Dielectric properties of thin solid films formed on silicon

We report on the measurement of the frequency-dependent complex permittivity, ()=()-i(), over the frequency range, 30 MHz to 6 GHz, of silicon wafers and of thin dielectric films formed on silicon. Measurements, as a function of temperature and time treatments, were obtained by means of an HP Network Analyzer and dielectric probe and the resulting ()and()plots for the silicon wafers are shown to have a Debye-type [1] profile, thereby indicating that the associated polarization mechanism is of the orientational variety.     

Simulation of the Process of Water Freezing in a Round Pipe

The problem of freezing of pure water in a round pipe is treated with due regard for convection under asymmetric thermal boundary conditions in the absence of motion along the pipe. The problem is solved numerically using the control volume approach, SIMPLER algorithm, and the enthalpy method. Results are obtained for three Grashof (Gr) and six Biot (Bi) numbers: Gr = 1.55 × 10⁶, Bi = 0.305 (0 < ), Bi = 0.044 ( < 2); Gr = 1.24 × 10⁷, Bi = 0.610 (0 < ), Bi = 0.087 ( < 2); Gr = 9.89 × 10⁷, Bi = 1.220 (0 < ), Bi = 0.174 ( < 2). The correctness of calculation of the problem disregarding free-convection flows is analyzed.     

Microstructure and mechanical properties of rapidly quenched L20 and L20+L12 alloys in Ni-Al-Fe and Ni-Al-Co systems

Ductile L2₀-type wires and+L1₂-type duplex wires with high strengths and large elongation in the Ni-Al-Fe and Ni-Al-Co ternary systems have been manufactured directly from the liquid state by an in-rotating-water spinning method. The wire diameter was in the range 80 to 180m and the average grain size was 2 to 4m for the wires and 0.2 to 1.0m for the+ wires. _y, _f and _p of the wires were found to be about 360 to 760 MPa, 560 to 960 MPa, and 0.2 to 5.5%, respectively, for the Ni-Al-Fe system, those of the+ wires were about 395 to 660 MPa, 670 to 1285 MPa, and 3.5 to 17%, respectively, for the Ni-Al-Fe system, and about 260 to 365 MPa, 600 to 870 MPa, and 4.0 to 7.0%, respectively, for the Ni-Al-Co system. Cold-drawing caused a significant increase in _y and _f and the values attained were about 1850 and 2500 MPa, respectively, for Ni-20Al-30Fe and Ni-25Al-30Co wires drawn to about 90% reduction in area. The high strengths, large elongation and good cold-workability of the melt-quenched and+ compound wires have been inferred to be due to the structural change into a low-degree ordered state containing a high density of phase boundaries, suppression of grain-boundary segregation and refinement of grain size.     

The morphology of α′ martensite in a two-phase (α+γ) Fe-Cr-Ni stainless steel

Both lath-shaped and martensites are induced by tensile deformation within of a two-phase ( + ) Fe-Cr-Ni stainless steel, forms from the through the at an intersection of two crystals. These are observed both when is surrounded by and when borders . The amount of strain at which both and nucleate, increases with test temperatures in the range –196 to 50° C. Adjacent laths are either twin-related, or 5, 9, 15 or 19° off the twin relationship, as found by analysing electron diffraction patterns.     

Study of the paramagnetic-antiferromagnetic transition and the γ → ε martensitic transformation in Fe-Mn alloys

The paramagnetic-antiferromagnetic transition and the martensitic transformation of Fe-Mn (Mn 15–32 wt%) alloys have been investigated by resistivity, dilatometry and X-ray diffraction (XRD). The results show that paramagnetic-antiferromagnetic transition increases the resistivity and the volume of alloys, whereas the martensitic transformation reduces the resistivity and volume of alloys. The A _f that was determined by the dilatometric method is not the temperature that martensites in the Fe-Mn alloys have reverse transformed to austenites completely. Mn additions reduce M _s, increase T _N and the lattice parameter of austenite in the Fe-Mn alloys. Both the antiferromagnetic transition and the martensitic transformation lead to an increase in the lattice parameter of austenite. The lattice parameters both above T _N and below T _N decrease linearly with temperature. The lattice parameter below M _s increases first and then decreases. Moreover, the (110) and (002) atomic planes in the Fe-15Mn-0.15C alloy are separated into two peaks: 2 for (002) is 44.16°, 2 for (110) is 44.47°.     

Transport properties of helium near the liquid-vapor critical point. II. Thermal conductivity of a3He-4He mixture

Measurements of the thermal conductivity are reported for an 80%³He-20%⁴He mixture above the critical point along several isotherms and near-critical isochores, using the same techniques and apparatus described for a study of³He. Using again the assumption that the observed conductivity can be decomposed into a sum of a regular and a singular contribution _reg and _sing, it is shown that along two near-critical isochores, _sing diverges. In particular, along the isochore showing the largest at the phase transition, the divergence is nearly the same as for³He and can be roughly characterized by a simple power law (T-T_c)^– with 0.58. This observation is contrary to predictions that foresee _sing0 asT _c is approached. The relaxation times characterizing the attainment of steady state conditions after switching the heat flux on and off show a similar behaviour as a function of reduced temperature as do those for pure³He. This result might indicate a substantial coupling between concentration and entropy diffusion. In the Appendix, the correlation length for³He nearT _c is calculated from heat conductivity, viscosity, and specific heat data.Work supported by Grant DMR 8024056 of the National Science Foundation.     

Mapping co-word structures: A comparison of multidimensional scaling and leximappe

The LEXIMAPPE method and Multidimensional Scaling (MDS) are discussed as methods to visualize (map) characteristics of structures of word-occurrence (co-word) relations. Utilization of MDS is proposed as an alternative mapping method able to circumvent problematic features of LEXIMAPPE maps of the total co-word structure. A comparison of both methods on the same real-life co-word matrix demonstrates topological advantages of an extended MDS-mapping.     

Numerical simulation of an explosive plasma generator in the gasdynamic approximation

A two-dimensional gasdynamic model of a plasma generator is proposed. A numerical solution of the problem is obtained, and peculiarities of the gasdynamic flow are considered. Results are compared with experiment.Notation T temperature - p pressure - N number of gas particles per unit volume - w gas mass velocity vector with components w_z=u and w_r=v - z axial coordinate - r radial coordinate - t time - E total specific energy of gas - specific internal energy - density - V plate velocity - E_in initial plate energy - M plate mass - S plate area - p pressure difference between left and right sides of plate - t, z, r time and space steps - k<1 Courant number - c velocity of sound in the gas Indices 0 initial value - * characteristic dimensional quantities - i, j grid cell indices along z and r - n number of time step - () symbol denoting intermediate values of gasdynamic variables in a time layer Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 37, No. 5, pp. 859–867, November, 1979.     

Effect of magnesium content on the stress exponent and effective stress in the steady state creep of Al-Mg alloys

The stress exponent of steady state creep,n, and the internal ( _i) and effective stresses ( _e) have been determined using the strain transient dip test for a series of polycrystalline Al-Mg alloys creep tested at 300° C and compared with previously published data. The internal or dislocation back stress, _i, varied with applied stress,, but was insensitive to magnesium content of the alloy, being represented by the empirical equation _i=1.084 ^1.802. Such an applied stress dependence of _i can be explained by using an equation for _i of the form _i (dislocation density)^1/2 and published values for the stress dependence of dislocation density. Values of the friction stress, _f, derived using the equation _e/=(1–c) (1– _f/), indicate that _f is not dependent on the magnesium content. A constant value of _f can best be rationalized by postulating that the creep dislocation structure is relatively insensitive to the magnesium content of the alloy.On leave from Engineering Materials Department, University of Windsor, Windsor, Ontario N9B 3P4, Canada.     

Precipitation sequence of various kinds of metastable phases in Al-1.0mass% Mg2Si-0.4mass% Si alloy

The precipitation of three new types of metastable phases, i.e., TYPE-A, TYPE-B and TYPE-C, with different crystal structures from the phase is proposed from our research on the change in crystal structures and formation sequence of metastable phases during the aging of the Al-1.0mass% Mg₂Si-0.4mass% Si alloy by a combination of analytical high resolution electron microscopy and energy dispersive X-ray spectroscopy. The sequence of their formation is explained as follows. First, precipitation of the phase and TYPE-B precipitate, then dissolution into the matrix and degradation of the TYPE-B precipitate. Finally, predominant precipitation of the metastable TYPE-A precipitate. The TYPE-C precipitate appeared heterogeneously in the over-aged condition.     

The θ projection method and small creep strain interpolations in a commercial Titanium alloy

The paper describes the early and final uniaxial creep behaviour of a Titanium alloy used for manufacturing intermediate power compressor disks and blades. Tests were conducted at the operating temperature (773 K) for such components and for rupture lives up to 3600 hours. Creep curves were fitted using either the conventional 4 model or the recently developed 6 equation. Parameters allowing the interpolation of times to small strains were produced and their accuracy checked against experimental values using distributions found to be most supported by the data. At strains above 0.75% both methods yielded zero mean interpolation errors. At strains above 0.27% and below 0.75% the 4 equation produced systematic errors in interpolation but the 6 function gave errors which were not statistically different from zero. For strains below 0.27% both techniques produced systematic interpolation errors but the 6 interpolations were always significantly better than their 4 counterparts. Both the 6 and 4 techniques produced systematic errors when predicting the failure time using interpolated rupture strains. Unlike the 4 function, the 6 equation produced unbiased predictions of the minimum creep rate and so produced failure time interpolations from the Monkman–Grant relation that were indistinguishable from zero.     

Solution of thermal conductivity problems with boundary condition of the third kind and arbitrary coordinate and time dependence of the biot number

An analytical solution of the thermal conductivity problem with boundary conditions of the third kind and arbitrary coordinate and time dependence of the Biot number is found in the form of a converging series of quadratures.Notation , z dimensionless coordinates - dimensionless temperature - Q dimensionless volume heat-liberation density per unit time - Fo=/² Fourier number - Bi₁(, Fo)=(, Fo) · / Biot number - thermal diffusivity coefficient - plate thickness - time - (, Fo) heat-liberation coefficient - thermal conductivity coefficient - i summation index - Jo zero order Bessel function of the first kind Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 41, No. 3, pp. 536–540, September, 1981.     

γ ? α2 Phase transformation in fractured high temperature stress rupture Ti-48Al-2Nb(at.%)

The ₂ phase transformation in fractured high temperature stress rupture Ti-48Al-2Nb(at.%) alloy has been studied by analytical electron microscopy. ₂ and phases were found at grain boundaries. ₂ layers that suspended in layers and interfacial ledge higher than 2d ₍₁₁₁₎ at /₂ interfaces were observed in the lamellar grains. These facts indicated that ₂ phase transformation and dynamic recrystallization have occurred during high temperature stress rupture deformation. It can be concluded that deformation induced ₂ phase transformation and dynamic recrystallization resulted in the presence of particles at grain boundaries. A structural and compositional transition area between deformation-induced ₂(or ) and its adjacently original (or ₂) phases was found by HREM and EDS and is suggested as a way to transform between and ₂ phase during high temperature stress rupture deformation. The transition area was formed by slide of partial dislocations on close-packed planes and diffusion of atoms.     

Theory of periodically driven,current-carrying,superconducting filaments. I. Spatially homogeneous states

Starting from the nonequilibrium theory of dirty superconductors in the Ginzburg-Landau regime, spatially homogeneous states with an applied currentI=I ₀+I ₁ cos (t) are considered. Expressions for the linear response (I₁ small) valid up to high frequencies (k _BT_c) are derived and evaluated analytically for the experimentally important case of smallI ₀ and ₀(T). Then the nonlinear response is treated for frequencies with _E1. Interesting new behavior is found for frequencies ₀ 1, where ₀ is essentially the GL relaxation time.     

Determination of the local angular radiation coefficients in certain two-body systems

A method is shown and formulas are derived by which local angular radiation coefficients can be determined in certain two-body systems where the configuration is arbitrary but one of the bodies is either a cylinder or a rectangular plate.Notation _int radiation vector of body 1 - _E ^int intrinsic radiation intensity of body 1 - _x, _y, _z components of the geometrical radiation vector along rectangular coordinates - r₀=x²+z² shortest distance from point M(x, y, z) to linear radiator - ₀ , ₀ ^' angles subtending the two segments of the linear radiator from point M(x, y, z) on area element 2 of irradiated surface - l length of the cylinders - x, y, z space coordinates of point M Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 22, No. 6, pp. 1080–1088, June, 1972.     

Swelling parameter of polypropylene used in household appliances

Samples of unfilled copolymer polypropylene were immersed in various solvents and the equilibrium swelling was recorded. Two-dimensional solubility maps of the Hildebrand parameter, , versus hydrogen bonding parameter, _c, and _h versus _v for polypropylene were plotted. Using the calculated percentage swell values and the solubility maps, the and _h values for detergent were postulated. No changes in the polypropylene backbone were revealed by mid- or far-infrared spectra, showing that the polypropylene polymer, when subjected to a number of different solvents, had not altered substantially.     

The influence of antimony-additions on the creep behaviour of a 25wt% Cr-20wt% Ni austenitic stainless steel

The effect of antimony on the creep behaviour (dislocation creep) of a 25 wt% Cr-20 wt% Ni stainless steel with ~ 0.005 wt% C was studied with a view to assessing the segregation effect. The antimony content of the steel was varied up to 4000 ppm. The test temperature range was 1153 to 1193 K, the stress range, 9.8 to 49.0 MPa, and the grain-size range, 40 to 600m. The steady state creep rate, , decreases with increasing antimony content, especially in the range of intermediate grain sizes (100 to 300m). Stress drop tests were performed in the secondary creep stages and the results indicate that antimony causes dislocations in the substructure to be immobile, probably by segregating to them, reducing the driving stress for creep.Nomenclature _a Creep stress in a constant load creep test without stress-drop - _A Initial applied stress in stress-drop tests - Stress decrement - ( _A-) Applied stress after a stress decrement, - t _i Incubation time after stress drop (by the positive creep) - _C Strain-arrest stress - _i Internal stress - _{s s}-component (= _i- _c) - Steady state creep rate (average value) in a constant load creep test - Strain rate at time,t, in a constant load creep test - New steady state creep rate (average value) after stress drop from _A to ( _A-) - Strain rate at time,t, after stress drop.     

Numerical solution of a micropolar fluid flow between two rotating coaxial disks

Summary Steady flow of a micropolar fluid between two rotating disks of infinite radius rotating at different/same speeds has been investigated. The lower and upper disks rotate with angular velocities and S respectively. By using similarity transformation method, the equations of motion are reduced to a set of ordinary non-linear coupled differential equations. The resulting non-linear equations are linearized by quasilinearization technique and integrated with the help of fourth order Runge-Kutta method via orthonormalization. Effects of micropolarity parameters on velocity components for different values of Reynolds numbers Re (200, 1000 etc.) andS (–1.0, 0.0, 0.5, 1.0) have been studied. Multiplicity of the solutions have been obtained for different values ofS and micropolar parameters at Re=1000. It is found that only one of the four micropolar parameters (₁) influences translation velocity components significantly. At high Re, flows similar to flows observed by Batchelor Stewartson and Holodniok etc., have been obtained. A new type of multiple solution has been obtained forS=1.0 which needs further investigation.     

Dielectric relaxation in polychlorotrifluoroethylene

The effect of increasing lamellar thickness in bulk polychlorotrifluoroethylene (PCTFE) by various methods (annealing and increasing time and temperature of crystallisation) on the parameters of the and relaxations has been studied.For the a relaxation consistent increase in temperature of maximum loss and activation energy with increasing lamellar thickness confirms the strong suggestion of earlier work [6] on oriented specimens and shows that the relaxation arises mainly in the interior of the lamellae with little contribution from the chain folds.No systematic changes in these parameters with increasing lamellar thickness was found for the relaxation and this is explained by the presence of _c and _a components in crystalline and amorphous regions respectively. The component _a (as well as the _c one) shows a marked anisotropy in magnitude with respect to the draw direction in oriented specimens relative to the direction of the applied electric field. This implies a lining up of the chain molecules parallel to one another in amorphous regions.The non-existence of analogous short chain compounds and experimental scatter prevented detailed checking of the consistency of the data for the relaxation with the theory for the _c-C _c model [5].     

Distribution characteristics of mechanical properties and correlation between the respective properties on S35C carbon steel

Mechanical properties of tensile strength, , upper yield stress, _SU, lower yield stress, _SL elongation, , area reduction, , Vickers hardness, H _v, and impact absorbed energy, E, were examined using 50 specimens of S35C carbon steel, which were machined from two bars supplied from the same charged and heat-treated material. Distribution characteristics of these properties are discussed, and the correlation between each pair of them is investigated from a statistical viewpoint. The main conclusions obtained are summarized as follows; distribution characteristics of _B, _SL, , , H _v and E are well approximated by a normal distribution, but those of asu are not approximated as well by this type of distribution. In the latter case, a Weibull distribution is preferable to represent the distribution pattern. No significant correlation was observed between each pair of the above mechanical properties. Consequently, individual properties have the inherent distribution characteristics independent of the other properties.