Hydrotropic properties of a novel alkylnaphthalene sulfonate

Alkylbenzenesulfonates based on toluene, xylene, as well as cumene, and alkylnaphthalenesulfonates, act as hydrotropes in surfactant systems. A novel sodium diisopropyl-naphthalene sulfonate (SDIPNS) has been devepoped that contains about 92% diisopropylnaphthalene sulfonate, compared to other diisopropylnaphthalene sulfonate preparations that contain less than 50% diisopropylnaphthalene sulfonate. This material is both a hydrotrope and a surfactant. The color of a 35% solution is light yellow, Gardner 3, significantly lighter than comparable materials. Draves wetting time for a 0.5% solution is about 30 s. The Ross-Miles foam test (1% solution) indicates a significant level of initial foam, but the foam is unstable. The solubilites of toluene and limonene in SDIPNS are much higher than in other hydrotropes tested. Hydrotropes raise the cloud point of nonionic surfactants; SDIPNS is the most efficient hydrotrope found for this application. Another measure of hydrotropicity is the amount of hydrotrope required to clear a cloudy detergent formulation; this hydrotrope is quite effective. Another measure is the modification of surfactant formulation viscosity; SDIPNS is quite effective. Additionally, SDIPNS changes the solubility of nonionic surfactants in water. SDIPNS is a surfactant as well as a hydrotrope, demonstrating a critical micelle concentration at about 1%. Presented as a poster session at the American Oil Chemists' Society Annual Meeting & Expo, May 11–13, 1998, Chicago, IL.     

Effect of hydrotropes on the aqueous solution behavior of surfactants

Aqueous solutions of surfactants—cationic: tetradecyltrimethylammonium bromide (C₁₄TABr); anionic: sodium dodecyl sulfate (SDS); and nonionic: polyoxyethylene t-octylphenol (trade name Triton X-102, also called OPE-8)— in the presence of three hydrotropes, viz., sodium xylene sulfonate, sodium p-toluene sulfonate, and sodium chlorobenzene sulfonate, were examined by measuring surface tension, viscosity, and cloud points for the nonionic surfactant. The results show a marked decrease in the critical micelle concentration with increase in hydrotrope concentration for C₁₄TABr, a marginal decrease for SDS, and very little change for OPE-8 up to 0.1 M hydrotrope. The viscosity of cationic surfactant solutions showed a remarkable increase in the presence of trace amounts of hydrotropes (up to 15 mM). In contrast, the SDS solution showed only a slight increase in viscosity at high hydrotrope concentration (150 mM), and the viscosity of the OPE-8 solution remained constant. The cloud point of OPE-8 increased in the presence of hydrotropes, unlike its behavior with the simple salt NaCl. The strong dependence of the solution behavior of cationic surfactants on the presence of hydrotropes is discussed in terms of electrostatic interaction.     

Hydrotropic and surfactant properties of novel diisopropyl naphthalene sulfonates

A novel surfactant and hydrotrope, sodium diisopropylnaphthalene sulfonate (SDIPNS) has been developed. It contains about 92% diisopropylnaphthalene sulfonate, compared to other materials which are less than 50% diisopropylnaphthalene sulfonate. Aqueous solutions of 34–36% active SDIPNS have dual functionality. They have excellent surface properties and are compatible with conventional anionic, nonionic, and amphoteric surfactants. They demonstrate good laundering detergency in combination with sodium lauryl ethoxy sulfate, with or without builder. They maintain surface activity in 150 ppm hard water (Ca²⁺/Mg²⁺=2∶1), 5% NaCl, pH 2, and pH 12. They are effective hydrotropes. They enhance surfactant solubility, raise the cloud point of nonionic surfactants, and modify the viscosity of surfactant formulations. They are light in color and are low-foaming. Presented as a Poster Session at the American Oil Chemists' Society Annual Meeting, May 9–12, 1999, Orlando, Florida.     

Aqueous Hydrotropic Solution as an Efficient Solubilizing Agent for Andrographolide from Andrographis paniculata Leaves

Abstract

An aqueous solution based extraction process for andrographolide from Andrographis paniculata leaves has been developed using alkyl benzene sulfonates and carboxylates as hydrotropes. The plant cells are permeabilized by the hydrotrope solutions followed by solubilization of andrographolide into the solutions. The extraction and solubilization of andrographolide is affected by structure and concentration of hydrotrope, temperature and particle size. Sodium cumene sulfonate (Na‐CS) shows the most efficient solubilization of andrographolide amongst the hydrotropes studied. The solubility of andrographolide increased by two orders of magnitude in Na‐CS aqueous solutions and ～96% andrographolide extraction was achieved in just 20 min.     

Influence of structure and counterions on physicochemical properties of linear alkylbenzene sulfonates

The effects of different inorganic and organic counterions on the physicochemical behavior of three commercial linear alkylbenzene sulfonates (LAS) have been studied. It has been found that the counterion hydration radius of the corresponding commercial linear alkylbenzene sulfonates has great influence on solubility, viscosity, surface tension and critical micelle concentration (CMC). The counterion has no influence on the detergency performance of the finished formulation. The alkyl chain length and the presence of tetralines have an important influence on solubility, viscosity and surface tension.     

Synthesis and Study of the Surface Properties of Alkylnaphthalene and Alkylphenanthrene Sulfonates

Some alkylnaphthalene and alkylphenanthrene sulfonates were synthesized by means of a Wurtz–Fittig reaction. The HLB values for the prepared compounds were calculated, and the basic properties were studied in water at different temperatures, namely, 25, 35 and 45 °C. Through surface tension measurements, the following values were determined: the critical micelle concentration (CMC) and the surface tension at the CMC (γ_CMC). The following values were calculated: area per molecule at the CMC (A_CMC), standard free energy change of micellization (ΔG _mic), standard free energy of adsorption (ΔG _ad), and the efficiency of a surfactant in reducing surface tension (pC20). Furthermore, the partition coefficients of the synthesized compounds were also measured. The results show that n-alkylnaphthalene and n-alkylphenanthrene surfactants studied exhibit desirable properties that may be of value in some fields such as detergency. To confirm the detergency power of the prepared surfactants, some foam studies were performed.     

Self-Assembly of Polyethylene Glycol Ether Surfactants in Aqueous Solutions: The Effect of Linker between Alkyl and Ethoxylate

The aqueous self-assembly behavior of two homologous series of poly(ethylene oxide) (PEO)-containing nonionic surfactants based on a C₁₀-Guerbet hydrophobe is reported. The two families of surfactants, alkyl ethoxylates and alkyl alkoxylates, are commercially available from BASF under the trade name Lutensol® XP-series and XL-series, respectively. The latter incorporate propylene oxide (PO) units in the surfactant chain. Dye solubilization was used to determine the critical micellization concentration (CMC) of each surfactant at 22 and 50 °C. The PO-containing alkyl alkoxylates displayed lower CMC values, which were also more sensitive to temperature. The Gibbs free energy, enthalpy, and entropy of micellization were computed from the CMC data and used to identify the contribution of each surfactant moiety (alkyl chain, PO unit, and PEO block) in controlling the CMC. The micellization properties are compared with compositionally similar surfactants with linear alkyl chains, yielding information about the effects of the Guerbet alkyl chain on micellization. Isothermal titration calorimetry was also used to characterize the CMC and enthalpy of micellization which generally compare well with the dye solubilization results. Cloud point data reveal nonmonotonic relationships for the Lutensol® surfactants with respect to composition, unlike linear alkyl chain surfactants. Finally, dilute solution viscosity measurements performed on some Lutensol® surfactants show a change in the slope, suggesting a structural change that tends to be more pronounced for surfactants with longer PEO blocks. The data presented herein enhance the understanding of surfactant structure–property relationships required for industrial formulation.     

Foaming of nonionic surfactant solutions: Effect of surfactant concentration and temperature

Foaming of solutions of the nonionic surfactant, octoxynol 9, was investigated in the concentration range of 0.010 to 5.00% and in the temperature range of 7–37 C, well below the cloud point of 65 C, by measuring the height and stability of foams generated by pouring thin streams of surfactant solutions into a glass column. All foams were fast-thinning. Their height increased monotonically with surfactant concentration. The rate of change of foam height with log surfactant concentration underwent no change at the CMC of 0.018%, but was four times lower above 0.146% than below 0.146%. Foams at lower temperatures generally thinned somewhat more slowly and were stronger or more cohesive and more stable than foams generated at higher temperatures by surfactant solutions of comparable concentrations. Oxidative degradation reduced foam height somewhat. Octoxynol 9 and sodium lauryl sulfate, rated as a good foamer, produced foams of comparable volume and stability.     

Synthesis and study of the surface properties of long-chain alkylnaphthalene sulfonates

Long-chain alkylnaphthalene sulfonates were synthesized by means of a Wurtz-Fittig reaction, and the basic properties were studied in water at 30°C. Through surface tension measurements, the following values were determined: the critical micelle concentration (CMC) and the surface tension at the CMC (γ_CMC). The following values were calculated: area per molecule at the CMC (A_CMC), standard free energy change of micellization (ΔG _mic ^o ), standard free energy of adsorption (ΔG _ad ^o ), and the “efficiency” of a surfactant in reducing surface tension (pC₂₀). The micelle aggregation numbers were measured through steady-state fluorescence-quenching methods. As the chain length of the hydrocarbon of n-alkylnaphthalene sulfonate increased, the Krafft temperature increased, the surface tension decreased, the value of CMC decreased, pC₂₀ increased, ΔG _ad ^o and ΔG _mic ^o became more negative, and the micelle aggregation number increased. The results showed that sodium α-(n-decyl)naphthalene sulfonate (DNS) had a high pC₂₀, low Krafft temperature, and lower CMC than other surfactants in this study. Thus, DNS and the other n-alkylnaphthalene surfactants studied exhibit desirable properties that may be of value in some fields such as detergency, oil recovery, and dyes.     

Rheological Investigation of Wormlike Micelles Based on Gemini Surfactant in EG–Water Solution

The self‐assembly behavior of gemini surfactants in ethylene glycol (EG)‐water (5/95, v/v) mixed solvent was investigated by rheological measurements at 10 °C. The influence of molecular structure of the gemini surfactant and added hydrotrope on the solution properties was studied. Sodium salicylate (NaSal) showed stronger ability to induce 2‐hydroxyl‐propanediyl‐α,ω‐bis‐(dimethyldodecylammonium bromide), referred to as 12‐3(OH)‐12, to form wormlike micelles than sodium benzoate. Less NaSal is required to promote a sphere to rod transition and to reach the peak viscosity. Moreover, the concentrations of hydrotrope and gemini surfactant are both lower than conventional single‐chain surfactant systems to reach a comparable viscosity. The strong hydrophobicity of gemini surfactants and hydrotropes is responsible for the high efficiency in forming wormlike micelles in EG/water systems. The geometric structure of gemini surfactants also plays a vital role in self‐assembly into wormlike micelles. Dimethylene‐1,2‐bis‐(dodecyl dimethylammonium bromide), referred to as 12‐2‐12, shows absolute superiority over 12‐3(OH)‐12 in constructing wormlike micelles. The present study will be helpful for developing de‐icing fluids and anti‐freezing solutions, which need rheology control in EG‐aqueous medium at low temperature.     

The molecular mechanism for destabilization of foams by organic ions

The effect of tetraalkylammonium ions on the destabilization of foam has been studied by measuring the half-life of foam (τ_1/2), area/molecule at the air/water interface, surface viscosity and critical micelle concentration (CMC) of sodium dodecyl sulfate (SDS). The area/molecule of SDS in organic salt solutions, calculated from the Gibbs isotherm, increases as the size of organic ion increases, and surface viscosity of the film decreases with the size of organic ions. The interaction of tetraalkylammonium ions with SDS decreases the CMC of the solution, and hence the concentration of SDS monomers decreases. The CMC of SDS decreases with the increase in the size and concentration of organic ions. The decrease in the CMC, increase in the area/molecule of SDS at the air/water interface and the decrease in surface viscosity by tetraalkylammonium ions all work to decrease the foam stability. The results indicate that the change in intermolecular distance between surfactant molecules in the adsorbed film by organic ions can significantly influence the surface viscosity and foam stability. The foam destabilizing efficiency of tetra-alkylammonium ions was superior or equivalent to that of tributyl phosphate and 2-ethyl hexanol, which are used in many antifoaming formulations.     

“Acid” pyrolysis-capillary chromatographic analysis of anionic and nonionic surfactants

A tandem “acid” pyrolysis-capillary chromatographic method for analyzing surfactants has been developed, and its application to the more common anionic and nonionic surfactant types investigated. In this method a surfactant is mixed with an acid, such as P₂O₅ or H₃PO₄, and dropped into a pyrolyzer attached to a capillary gas chromatograph. The resulting volatile pyrolyzate is carried into the chromatograph for analysis. According to the chromatograms, the point of cleavage during “acid” pyrolysis is quite selective, usually at a C-S or C-O bond. For example, LAS and ABS give peaks corresponding to the alkylbenzene precursors; primary linear alkyl sulfates and sulfonates, peaks corresponding to olefins with the same number of carbon atoms as the alkyl group; and alcohol and alkylphenol ethoxylates and ethoxylate sulfates, peaks corresponding to olefins from the alkyl group and to acetaldehyde and a higher aldehyde from the polyethoxy group. Alkylphenol derivatives are probably cleaved to form an alkylphenoxy intermediate, which then dealkylates to give the olefins. This method is quantitative for carbon number or carbon number and isomer distribution of hydrophobes in linear surfactants, semiquantitative for ethoxy content and for hydrophobes in branched chain surfactants, and qualitative for hydrotropes and certain foam additives. Surfactants, as well as mixtures of certain surfactant types, in built detergent formulations can be analyzed without isolation. Winner, Bond Award Medal, Philadelphia, October 1966.     

An Alternative Approach for Determining Critical Micelle Concentration: Dispersion of Ink in Foam

The present work investigates the critical micelle concentration (CMC) of nonionic surfactant solutions using a new approach by monitoring the dirt dispersion (DD) defined as the amount of dirt absorbed by foam using India ink as a model dirt. DD has so far been studied qualitatively by eye estimation. Our quantification studies show that DD increases with increasing surfactant concentration and reaches a maximum. After this, it decreases and becomes very small. The concentration for which DD is maximum corresponds to the CMC, as determined from surface tension measurements. The CMC of natural surfactants obtained from plants Sapindus mukorossi, Albizia procera, Juglans regia, Zephyranthes carinata, and Acacia concinna was determined. The CMC obtained by DD are in reasonably good agreement with those obtained using the surface tension method. The DD method is easy, rapid, and inexpensive and can become an effective tool for estimating the CMC.     

Effective Separation of Petro Products through Hydrotropy

This paper presents a comprehensive study on the effect of hydrotropes such as sodium salicylate, sodium benzoate, and nicotinamide on the separation of a near boiling mixture, o‐/p‐xylene. The influence of a wide range of hydrotrope concentrations (0 to 3.0 mol/L) and different system temperatures (303 to 333 K) on the separation of o‐/p‐xylene were studied. All hydrotropes used in this work showed an enhancement in the percentage extraction of p‐xylene to different degrees. The percentage extraction of p‐xylene from the o‐/p‐xylene mixture increases with an increase in hydrotrope concentration and also with system temperature. A minimum hydrotrope concentration (MHC) was found essential to initiate significant extraction of p‐xylene from the o‐/p‐xylene mixture. The maximum enhancement factor, which is the ratio of the value in the presence and absence of a hydrotrope, was determined for both cases. The Setschenow constant, k_s, a measure of the effectiveness of a hydrotrope, was determined for each case.     

Effect of hydrotropes on solubility and mass transfer coefficient of lauric acid

A comprehensive investigation on the solubility and mass transfer coefficient enhancement of lauric acid through hydrotropy has been undertaken. The solubility and mass transfer studies were carried out using hydrotropes such as sodium cumene sulfonate, sodium p-xylene sulfonate and sodium p-toluene sulfonate under a wide range of hydrotrope concentrations (0 to 3.0 mol/L) and different system temperatures (303 to 333 K). The effectiveness of hydrotropes was measured in terms of Setschnew constant K _s and reported for all hydrotropes used in this study. The solubility data are also fitted in a polynomial equation as the function of hydrotrope concentration.     

Experimental Study of CMC Evaluation in Single and Mixed Surfactant Systems, Using the UV–Vis Spectroscopic Method

In this study, the critical micellar concentration (CMC) of anionic, cationic and nonionic surfactants was determined using the UV–Vis spectroscopic method. Sodium lauryl sulfate (SDS) as anionic, hexadecyl-trimethyl-ammonium bromide as cationic, tert-octylphenol ethoxylates TOPEON (with N = 9.5, 7.5 and 35) and lauryl alcohol ethoxylate (23EO) as nonionic surfactants have been used. Concentration of surfactants varies both from below and above the CMC value in the pyrene solution. In addition, the amount of the CMC was determined using the values from the data obtained from the graph of absorbance versus concentration of surfactants. A comparative study was conducted between the results of the present study and the literature which shows a good agreement, in particular for TOPEO9.5 and LAEO23. Furthermore, the CMC value of SDS (as an ionic surfactant) in the presence of nonionic surfactants was also examined. The result reveals that with addition of small amount of nonionic surfactant to the anionic SDS surfactant, a decline in the CMC value of the anionic–nonionic system relative to the CMC of pure anionic surfactant was observed. In addition and for the first time, the effect of UV irradiation on the size of the micelle formations was studied. It was found that UV irradiation causes the formation of smaller micelles which is of prime concern in membrane technology.     

Association of nonionic polymer with hydrocarbon/fluorocarbon surfactant in aqueous solution

The interaction between a nonionic polymer and a hydrocarbon or fluorocarbon surfactant has been investigated by means of surface tension, viscosity, electroconductivity, fluorescence probing, solubilization of a waterinsoluble dye, and electron spin resonance (ESR). The systems studied consisted of polyvinylpyrrolidone (PVP) with lithium dodecyl sulfate (LiDS) or lithium perfluorooctane sulfonate (LiFOS). Surface tension measurements indicated that formation of PVP-surfactant complex is more favorable in the PVP-LiFOS system than in the PVP-LiDS system, and that the adsorbed amount of LiFOS is less than that of LiDS, although the CMCs of the surfactants are almost the same. In the PVP-LiFOS system, the relative viscosity and the solubilized amount of a water-insoluble dye showed a maximum at a certain concentration of LiFOS in the region between two transitions observed in the surface tension, where also a change in the slope of the electroconductivity is observed. These results indicate that shielding of effective charge of the PVP-LiFOS complex causes a conformational change of PVP wrapped around the aggregate of LiFOS with an increase of free surfactant in the bulk phase. The conformational change can be correlated with microenvironmental properties of PVP-surfactant complexes. The microviscosity estimated with ESR indicated that the headgroups of LiFOS adsorbed on PVP are less tightly packed than those of LiFOS micelles, while an opposite result was obtained in the PVP-LiDS system. In particular, the marked high viscosity at a low concentration of LiFOS in the PVP-LiFOS system can probably be attributed to rigidity of the fluorocarbon chain of LiFOS.     

ENHANCEMENT OF SOLUBILITY AND MASS-TRANSFER COEFFICIENT OF 1,2-DIHYDROXY-9,10-ANTHRAQUINONE (ALIZARIN) THROUGH HYDROTROPY

The effect of hydrotropes potassium p-toluene sulfonate (KPTS), citric acid, and nicotinamide on the solubility and mass-transfer coefficient of 1,2-dihydroxy-9,10-anthraquinone (alizarin) was studied. Solubility studies were carried out under a wide range of hydrotrope concentrations (0 to 3.0 mol·L^?1) and different system temperatures (303 to 333 K). It was observed that the solubility and mass-transfer coefficient of alizarin increases with an increase in hydrotrope concentration and system temperature. The maximum enhancement factor, the ratio of the value of solubility in the presence and absence of a hydrotrope, was determined for all experiments under study. The effectivity of hydrotropes was measured by the determination of the Setschenow constant, K_s. The order of effectiveness of various hydrotropes based on K_s values is potassium p-toluene sulfonate > citric acid > nicotinamide.     

EXTRACTIVE DISTILLATION WITH AQUEOUS SOLUTIONS OF HYDROTROPES

The effect of hydrotropes on vapor-liquid equilibrium of a mixture provides a potential technique of extractive distillation for systems which are difficult or impossible to separate by normal rectification. Various hydrotropes, such as sodium toluate, sodium toluence sulfonate, sodium cymcnc sulfonate, sodium mesitylene sulfonate and sodium salicylate, in aqueous solutions have been tested for the separation of close-boiling point mixtures, such as p-cresol/2,6-xylenol, isopropanol/ fm-butanol, and wc-butanol/rert-butanol. The changes in the relative volatility increase with the concentration of hydrotrope and with the hydrotrope to solute ratio.     

Experimental Study on Foam Properties of Mixed Systems of Silicone and Hydrocarbon Surfactants

Silicone surfactants are inevitably involved in industrial applications in combination with hydrocarbon surfactants, but properties of the mixtures of silicone and hydrocarbon surfactants have received little attention, especially foam properties of the mixtures. In this study, aqueous solutions of respective binary mixtures of a nonionic silicone surfactant with anionic, cationic, and nonionic hydrocarbon surfactants were prepared for evaluation of their foam properties. Surface tension of aqueous solutions of the mixtures were measured with the maximum bubble pressure method. Foaming ability and foam stability of the mixtures were then evaluated with the standard Ross–Miles method. The findings show that the addition of the silicone surfactant results in a decrease in surface tension for aqueous solutions of the hydrocarbon surfactants. The critical micelle concentration (CMC) of the hydrocarbon surfactants is also changed by the additive silicone surfactant. Additionally, clear foam synergistic effects were observed in the mixtures of silicone and hydrocarbon surfactants, regardless of the ionic types of the hydrocarbon surfactant. The foam stability of the hydrocarbon surfactant was shown to generally improve with the increasing concentration of the silicone surfactant. Even so, aqueous solutions of different ionic hydrocarbon surfactants in the presence of the silicone surfactant will give different foam stabilities. The results of the present study are meant to provide guidance for the practical application of foams generated by the mixtures of the silicone and hydrocarbon surfactants.