Studies of reactions with polymers. I. The reaction of maleic anhydride with PVA and the properties of the resultant

Graft copolymerization of maleic anhydride (MA) onto PVA was carried out both in the presence and absence of the initiator. In the former case, the resultant was a copolymer containing a carboxylic acid and a keto-olefinic side chain. Therefore, the reaction product, viscosity, gel content, and mechanical properties differed from the resultant of the latter, which was obtained by esterification of PVA by MA. Both resultants showed polyelectrolytes characteristics. The dependence of the grafting percentage on the concentration of the initiator, the concentration of the monomer, the reaction temperature, and the reaction medium was studied. Grafted copolymers after heat treatment showed remarkable mechanical strength in the wet state when compared with original PVA.     

Studies of reactions with polymers. III. Syntheses and properties of poly(vinyl alcohol) graft terpolymers

A condensation-coupling reaction through esterification is performed between the hydroxy groups of poly(vinyl alcohol) (PVA) and the anhydride groups of methyl methacrylate (MMA)-co-maleic anhydride (MA) copolymer to produce the PVA-g-MMA/MA graft terpolymer. The MMA-co-MA copolymer was obtained by copolymerization of MA and MMA in dimethyl sulfoxide by using azobisisobutyronitrile as initiator. The structure of reaction products was confirmed by infrared analysis, and the dependence of composition, viscosity, and yield of the graft terpolymer on the MA content in MMA-co-MA as well as the concentration of the reactants fed were investigated. Mechanical properties, water content, and gel content of the membranes of terpolymers were measured over a wide range of compositions. PVA-g-MMA/N-ethylol maleimide was also synthesized by reacting the residual anhydride groups on PVA-g-MMA/MA with ethanol amine, this reaction proceeds through the PVA-g-MMA/N-ethylol maleamic acid intermediate.     

Amphiphilic graft copolymer latex membranes. VI. Poly(vinyl alcohol)–acrylonitrile–N-hydroxyethyl acrylamide graft copolymer latex membranes

Poly(vinyl alcohol)(PVA)–acrylonitrile(AN)–N-hydroxyethyl acrylamide (HEAAm) graft copolymer latex membranes were prepared and properties of the membranes were compared with those of PVA–AN graft latex membranes and Cuprophane PT-150. The physical constants of HEAAm were determined and the tautomerization between hydroxyethyl amide group and aminoethyl ester group upon pH changes was ascertained by infrared spectrum of poly(HEAAm) film. An increase in HEAAm content in the membrane enhanced permeabilities of solute in aqueous solutions in comparison with PVA–AN graft latex membranes, maintaining good mechanical properties in wet state. With pH variation, the permeability of the nonionic solute was unchanged, but that of the anionic solute in acidic condition was superior to that in basic condition, and the permeability of the cationic solute exhibited the opposite trend. The behavior of ionic solute were attributable to the effect of the tautomerization of the functional group in the membrane.     

两亲性接枝共聚物PVA-g-PBA的合成与表征

以过硫酸钾 (KPS)为引发剂 ,将丙烯酸丁酯 (BA)接枝到聚乙烯醇 (PVA)上 ,制得两亲性接枝共聚物 PVA-g-PBA。用红外光谱、X射线衍射表征了接枝物 ,研究了引发剂浓度、单体浓度及反应时间对单体转化率、接枝率和接枝效率和接枝率对共聚物吸水性能的影响。结果表明在水介质中 ,氮气保护下 ,70℃时 ,以过硫酸钾 (KPS)为引发剂 ,将丙烯酸丁酯 (BA)接枝到聚乙烯醇 (PVA)上 ,[PVA]为 2 .5× 1 0 -4mol/ L,[BA]为 0 .63 mol/ L、[KPS]为 5 .5 5× 1 0 -4时 ,反应 5 h,能获得较高 CM、G和 Ge的接枝物。接枝物的接枝率越高 ,吸水率越低 ,吸水 1 0 h达平衡 ,最大平衡吸水率为 1 88.8%。     

Porous acrylonitrile/itaconic acid copolymers prepared by suspended emulsion polymerization

Porous acrylonitrile (AN)/itaconic acid (IA) copolymers were successfully prepared by suspended emulsion polymerization for the first time, with potassium peroxydisulfate (KPS) as an initiator, poly(vinyl alcohol) (PVA) as a dispersant agent, and Span80 as an emulsifier. The effects of the water/monomer mass ratio, agitation conditions, KPS concentration, PVA concentration, Span80 concentration,s and IA concentration on the average particle size and size distribution, particle morphology, and porosity of the AN/IA copolymers were investigated. The results show that the final AN/IA copolymers formed with agglomerates of primary particles had a porous structure, low particle density, and uniform particle size and did not agglomerate easily between the particles. The preparation conditions for the AN/IA copolymers were optimized as follows: (1) the water/monomer mass ratio was 0.3 : 1; (2) the concentrations of KPS, IA, PVA, and Span80 were 0.5, 12.4, 0.1, and 0.5 wt %, respectively, based on the weight of AN separately; (3) the agitation rate was 400 rpm; (4) the polymerization temperature was 70°C; and (5) the reaction time was 3 h. The size of the final AN/IA copolymer particles was in the range 200–400 μm. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and properties of acrylonitrile–EPDM–N-vinylcarbazole graft terpolymer

A graft terpolymer of acrylonitrile (AN) and N-vinylcarbazole (NVC) onto ethylene–propylene–diene terpolymer (EPDM) was synthesized in toluene using benzoyl peroxide. The effects of EPDM content, mole ratio of NVC to AN, reaction time, reaction temperature, and initiator concentration in the graft copolymerization were examined. The synthesized AN–EPDM–NVC graft terpolymers (AEVC) were identified by infrared (IR) and ¹H-NMR (nuclear magnetic resonance) spectra. The thermal stability, tensile strength, and light resistance of AEVC were investigated by using a Fade-o-Meter, thermogravimetric analyzer, and tensile tester. It was found that the heat resistance of AEVC is considerably better than that of acrylonitrile–butadiene–styrene (ABS) copolymer. © 1995 John Wiley & Sons, Inc.     

PE氯化接枝St/AN共聚共混物研究

采用固相法对聚乙烯(PE)进行氯化接枝苯乙烯/丙烯腈(St/AN)单体,制得了改性氯化聚乙烯(CPE)材料。探讨了氯化反应温度、氯含量、引发剂过氧化苯甲酰(BPO)用量和单体配比对聚合物力学性能的影响,实验中还对PE接枝了不同单体,结果表明,采用二段温度(70℃,120℃)法,氯质量分数为35%,BPO加入质量为0.24g,m(St)/m(AN)为1:1时,可制得力学性能较好的CPE材料。极性单体MA、AN及St的加入提高了CPE材料的拉伸强度。     

Radiation-initiated graft copolymerization of individual monomer and comonomer onto polyethylene and polytetrafluoroethylene films

Preparation and some properties of the graft copolymers obtained by radiation-induced graft polymerization of methacrylic acid (MAA) and (acrylonitrile/MAA) comonomer onto polyethylene and polytetrafluoroethylene films, were investigated. The effect of reaction conditions, solvent, monomer, and inhibitor concentration, comonomer composition, and comonomer concentration, on the graft copolymerization process was studied. The grafting process was enhanced in the presence of comonomer (AN/MAA) as compared with individual grafting of MAA or acrylonitrile (AN). The optimum comonomer composition, at which the highest grafting yield was obtained, was found to be (80/20) wt % of (AN/MAA) comonomer. The graft copolymerization of (AN/MAA) comonomer was enhanced in presence of AN due to its higher polarity strength. The electrical and swelling properties of the graft copolymers were greatly affected by the contents of PAN and PMAA graft chains. Mechanical properties of the graft copolymers were significantly changed with the grafting yield.     

Uses of electron‐beam irradiation to prepare pH‐ and temperature‐sensitive hydrogels from reactive poly(vinyl alcohol) grafts

Thermosensitive poly(vinyl alcohol)‐graft‐(maleic anhydride), PVA‐MA, and poly(vinyl alcohol)‐graft‐(N‐isopropylacrylamide maleic anhydride) (PVA‐MA‐NIPAAm) copolymers containing carboxyl groups were prepared using electron beam irradiation at dose 80 kGy. The swelling ratios of the cross‐linked gels were measured at various temperatures. The LCST values were measured using DSC technique. The temperature dependence of the swelling ratios of the cross‐linked copolymers and terpolymers were measured at different temperatures. The swelling ratios of copolymers increased with increasing temperature up to 25–38°C, then decreased. The swelling behavior of both copolymers and terpolymers was referred to formation of hydrogen bonds between amide group of NIPAAm moieties and carboxyl group in MA moieties and to hydrophobic interaction due to methyl groups of NIPAAm. The swelling behaviors of these gels were analyzed in buffer solution at various pH. Swelling ratios of all gels were relatively high and they showed reasonable sensitive to pH. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Grafting onto wool. XI. Graft copolymerization of poly(vinyl acetate) and poly(methyl acrylate) onto reduced wool in presence of potassium persulfate–ferrous ammonium sulfate (KPS—FAS) system as redox initiator

In an attempt to ascertain the role of—SH groups of Himachali wool during graft copolymerization, poly(viny acetate) (PVAc) and poly(methyl acrylate) (PMA) were graft copolymerized onto reduced wool by using potassium persulfate—ferrous ammonium sulfate (KPS—FAS) redox pair in aqueous medium. Reduction of wool was carried out by sodium bisulfite solution of varying concentrations for different reaction periods. Concentration of reducing agent and the extent of reduction were found to influence grafting of vinyl monomers. Maximum grafting of methyl acrylate (MA) and vinyl acetate (VAc) occurred when wool was reduced by 1% and 0.5% NaHSO₃ solution, respectively, for 24 h. Increase in percent grafting of MA onto reduced wool compared to that of unreduced wool has been ascribed to the production of more—SH groups by reduction of—SS—groups of wool fiber.     

Synthesis and characterization of terpolymer of N‐cyclohexylmaleimide,methyl methacrylate,and acrylonitrile

Terpolymers of N‐cyclohexylmaleimide, methylmethacrylate, and acrylonitrile (AN) at different AN feed content were synthesized by suspension polymerization. The thermal properties of the terpolymers such as glass transition temperature (T_g) and Vicat softening temperature (T_Vicat) were determined by torsion braid analysis and Vicat softening temperature tester, respectively. The value of T_g and T_Vicat decreased with increasing AN feed content. Thermogravimetric analyses were carried out with the results that the incorporated AN units enhanced the thermal stability of the resulting polymers and a second degradation step appeared with the addition of AN. The mechanical properties (tensile strength and impact strength) of the terpolymers were also detected and the results show that the tensile strength and impact strength of terpolymers increase with increasing AN feed content. The rheological results illustrated that the terpolymers showed rheological behavior similar to that of pseudoplastic liquid. The apparent shear viscosity decreased with the increasing of AN feed content. The flow power index n increased with increasing AN feed content. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 792–796, 2007     

High char‐yielding poly[acrylonitrile‐co‐(itaconic acid)‐co‐(methyl acrylate)]: synthesis and properties

Polyacrylonitrile terpolymers of various compositions consisting of acrylonitrile (AN), itaconic acid (IA) and methyl acrylate (MA) were synthesized by solution polymerization in dimethylsulfoxide. Increase in concentration of either IA or MA retarded the overall polymerization rate and the polymer molecular weight. The system consisting of AN + MA and varying IA concentration was more prone to retardation in comparison with the system composed of AN + IA with variable MA concentration. The retardation factors were quantified. Minor quantities of MA boost the reactivity of IA in the terpolymer system. The terpolymer was richer in MA vis‐à‐vis the feed. The thermal characteristics of the terpolymer were examined as a function of its composition. In contrast to the copolymer of AN and IA requiring 1–1.5 mol% IA, the terpolymer required an IA content of approximately 2.5 mol% for optimum thermal stability. The polymer with 90 mol% AN, 2.5 mol% IA and 7.5 mol% MA exhibited reasonably good char‐forming characteristics and thermal stability. The overall crystallinity and crystallite size of the polymers were found to decrease on incorporation of the comonomers. The ‘aromatization index’ of the copolymer increased with the temperature of pyrolysis through re‐organization of the tetrahydropyridine ladder structure. Copyright © 2005 Society of Chemical Industry     

Cationic Graft Polymerization of 2-Oxazolines on Poly(vinyl alcohol) Derivatives

The graft polymerization of various monomers onto PVA has been studied by radical polymerization mechanism. Successful grafting of acrylonitrile (AN), acrylamide (AAm), acrylic acid, methyl methacrylate, and vinyl acetate was reported by using chemical (Minoet al., 1959; Ide, 1961; Maskimov et al., 1965) and radiation (Misra et al., 1987) methods. On the other hand, less attention has been paid to ionic graft polymerization. Sasson and Zilkha reported on grafting formaldehyde onto potassium-metallated PVA (Sasson and Zilkha, 1969). Galin studied grafting of AN and propane sulfone onto sodium-metallated PVA (Galin, 1971). We used the same anionic system for the polymerization of AAm (Ikeda and Suzuki, 1980).     

Synthesis and thermal analysis of emulsion terpolymers of N‐phenylmaleimide,methyl methacrylate,and acrylonitrile

Terpolymers of N‐phenylmaleimide (PMI), methyl methacrylate (MMA), and acrylonitrile (AN) were synthesized by emulsion polymerization. The thermal properties of the terpolymers, at different PMI and AN feed contents, were investigated by TBA, TGA, and the Vicat softening point test. The results show that the glass transition temperature (T_g) and decomposition temperature of the terpolymers increase with increasing PMI feed content. Furthermore, the Vicat softening points of the terpolymers increase with the PMI feed content. The M?_w and M?_n of the terpolymers were also determined by GPC. The results show that the M?_w and M?_n of the terpolymers have a maximum value in the range of 0–30% PMI feed content and decrease with an increasing AN feed content. The mechanical properties (tensile strength and impact strength) of the terpolymers decrease with an increasing PMI feed content and increase with an increasing AN feed content. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2455–2462, 2001     

Graft polymerization of acrylonitrile onto paper and characterization of the grafted product

The chemical graft copolymerization reaction of acrylonitrile (AN) onto paper sheet was performed. The effect of initiator concentration, monomer concentration, and temperature on the reaction rate was studied. The reaction rate equation of the graft copolymerization reaction is found to be R_P = K₂ [initiator]^0.54[monomer]^1.13. The apparent activation energy (E_a) of the copolymerization reaction is found to be 35.99 KJ/mol. The infrared characteristic absorption bands for cellulosic paper structure and the paper gr‐AN are studied. Tensile break load, porosity, and burst strength were measured for the grafted and pure paper sheet. It was found that the mechanical properties are improved by grafting. The chemical resistance of the graft product against strong acid (HCl), strong alkali (NaOH), polar and nonpolar solvents was investigated. It was found that the resistance to these chemicals is enhanced by grafting. From the TGA and DTA data, it is clear that the grafted paper sheet is more thermally stable than pure paper sheet. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Solid state grafting copolymerization of acrylamide onto poly(vinyl alcohol) initiated by redox system

A solid state grafting copolymerization of acrylamide (AM) onto poly(vinyl alcohol) (PVA) was conducted with ammonium persulfate and sodium bisulfite redox system as initiators. Before the reaction the PVA powder and required amount of AM were mixed evenly, and sprayed with water to swell the PVA powder and to dissolve AM. Then the swollen PVA powder was sprayed with the redox solution, and the reaction temperature was controlled at a temperature between 30°C and 80°C for 120 min. The grafting percentage and efficiency were determined as functions of monomer/PVA ratio, initiator concentration and reaction temperature. The structure and performance of the graft copolymers were confirmed by FTIR‐ATR, XRD, ¹³C NMR, and thermogravimetric analysis, together with mechanical property and apparent viscosity measurements. It has been confirmed that grafting copolymerization of AM onto PVA initiated by this redox system occurred with higher grafting percentage and efficiency in the solid state. The thermal stability and water‐solubility of grafted PVA were found to be better than those of unmodified PVA. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39938.     

Separation of liquid mixtures by using polymer membranes. IV. Water-alcohol separation by pervaporation through modified acrylonitrile grafted polyvinyl alcohol copolymer (PVA-G-AN) membranes

The acrylonitrile (AN) grafted onto polyvinyl alcohol (PVA) can improve the mechanical properties and water resistance of PVA; however, its hydrophilicity is decreased. Prepared PVA-g-AN membranes through modification with the NaOH and HCHO aqueous solutions can enhance its hydrophilicity. This modified PVA-g-AN membranes were used to separate alcohol/water solution with the pervaporation method. The flux was increased from 0.72 kg/m² h of the original membrane to 2.06 kg/m² h of the modified membrane. Moreover, adding a small quantity of CoSO₄ to the water-alcohol mixture can simultaneously increase the separation factor. © 1993 John Wiley & Sons, Inc.     

Dynamic mechanical properties of photopolymerizable poly(vinyl alcohol)–acrylate monomer blends

Dynamic mechanical properties of photopolymerizable poly(vinyl alcohol) (PVA)–monoacrylate blends were investigated by measuring dynamic shear modulus G′ and loss tangent, tan δ. The dynamic mechanical properties of the blends before being exposed to UV irradiation were governed by the weight percent of the monomers which act as plasticizers. On the other hand, the UV-irradiated blends seemed to be typical two-phase materials since they revealed two tan δ maxima whose positions were independent of the monomer content. Those two maxima were assigned to PVA and photopolymerized acrylates with reference to the dynamic mechanical data of PVA and a PVA-polyacrylamide polyblend. Those dynamic mechanical data suggested that insolubilization of the blend type photopolymers should be caused by a decrease in solubility due to graft polymerization of acrylate monomers onto PVA.     

Synthesis and properties of acrylonitrile-CR-methyl methacrylate graft copolymer

Graft copolymerization of acrylonitrile (AN) and methyl methacrylate (MMA) onto polychloroprene (CR) was carried out using benzoyl peroxide as initiator. The effects of mole ratio of AN to MMA, reaction temperature, reaction time, solvent, and initiator concentration on the graft copolymerization were examined. It was found that the thermal stability and weatherability of the AN—CR—MMA graft copolymer (ACM) were considerably better than those of CR.     

Graft Copolymerization of Styrene‐Maleic Anhydride Onto Poly(Vinyl Chloride) and Its Cross‐linking by Toluene Diisocyanate: Characterization,Thermal, and Mechanical Properties

In this work, styrene‐maleic anhydride (St‐MA) copolymer was successfully grafted onto poly(vinyl chloride) (PVC) by means of chemical method in cyclohexanone medium. In this manner, the effects of various parameters such as total monomer content, monomers ratio, and initiator concentration on the grafting percentage (GP) and acid value (AV) were examined. The graft copolymers were characterized by Fourier‐transform infrared and nuclear magnetic resonance spectroscopy methods. Afterward, the cross‐linking reaction was carried out through MA hydrolysis and condensation reaction between maleic acid and produced diamines, by toluene diisocyanate (TDI) at the presence of hot water. The results showed that the GP and AV of PVC‐g‐(St‐MA) copolymers were considerably higher than those of PVC‐g‐MA and PVC‐g‐St with significant molecular weight. A gel content of 56% was attained with 1 phr TDI in PVC‐g‐(St‐MA) copolymer. The glass transition temperatures and mechanical properties of PVC‐g‐(St‐MA) samples were increased compared to pure PVC. Cross‐linked PVC‐g‐(St‐MA) showed improved mechanical properties than other samples, but the glass transition temperature of PVC backbone in this cross‐linked copolymer was disappeared due to its heavily dense structure. J. VINYL ADDIT. TECHNOL., 25:377–384, 2019. © 2019 Society of Plastics Engineers