Effect of tool rotational speed and pin profile on microstructure and tensile strength of dissimilar friction stir welded AA5083-H111 and AA6351-T6 aluminum alloys

The relatively new welding process friction stir welding (FSW) was applied in this research work to join 6 mm thick dissimilar aluminum alloys AA5083-H111 and AA6351-T6. The effect of tool rotational speed and pin profile on the microstructure and tensile strength of the joints were studied. Dissimilar joints were made using three different tool rotational speeds of 600 rpm, 950 rpm and 1300 rpm and five different tool pin profiles of straight square (SS), straight hexagon (SH), straight octagon (SO), tapered square (TS), and tapered octagon (TO). Three different regions namely unmixed region, mechanically mixed region and mixed flow region were observed in the weld zone. The tool rotational speed and pin profile considerably influenced the microstructure and tensile strength of the joints. The joint which was fabricated using tool rotational speed of 950 rpm and straight square pin profile yielded highest tensile strength of 273 MPa. The two process parameters affected the joint strength due to variations in material flow behavior, loss of cold work in the HAZ of AA5083 side, dissolution and over aging of precipitates of AA6351 side and formation of macroscopic defects in the weld zone.     

Microstructures and mechanical properties in dissimilar AZ91/AZ31 spot welds

The stir zone microstructures and mechanical properties of dissimilar AZ91/AZ31 friction stir spot welds made using different tool designs and tool rotational speed settings are investigated. Intermingled AZ91 and AZ31 lamellae are formed in the stir zones of dissimilar spot welds made using threaded, three-flat/0.7 mm/threaded and three-flat/no-thread tools and tool rotational speeds ranging from 1500 to 3000 rpm. The intermingled lamellae have chemical compositions, which are similar to those of the upper and lower sheets in the dissimilar sandwich. The flats on the rotating tool facilitate the downward transfer of upper and lower sheet materials in the location close to the pin periphery and therefore intermingled AZ91 and AZ31 lamellae are formed in the stir zones of dissimilar spot welds produced using a three-flat tool without a thread.The distance (Y) from the tip of the hook region to the keyhole periphery has a dominant influence on the mechanical properties of dissimilar AZ91/AZ31 spot welds, since the hook regions are curved inwards towards the axis of the rotating tool. The highest failure load properties and largest Y-values are found in dissimilar spot welds made using threaded and three-flat/0.7 mm/threaded tools and tool rotational speeds from 1500 to 3000 rpm. Dissimilar spot welds made using a rotational speed of 1000 rpm have the smallest Y-values and the lowest failure load properties.     

Feasibility study of friction spot welding of dissimilar single-lap joint between poly(methyl methacrylate) and poly(methyl methacrylate)-SiO2 nanocomposite

In this work, the feasibility of friction spot welding (FSpW) of a commercial poly(methyl methacrylate) (PMMA) GS grade and a PMMA 6 N/2 wt% silica (SiO₂) nanocomposite was investigated. Single-lap joints welded at rotational speeds of 1000, 2000 and 3000 rpm were produced. The analysis of the joint microstructure and material flow pattern indicated that joints could be produced using all of the tested welding conditions. However, the joint produced at 1000 rpm displayed sharp weld lines (weak links), indicating insufficient heat input, while the welds produced at 3000 rpm displayed excessive plastic deformation (bulging of the bottom plate), volumetric defects and a lack of material mixing in the welded area, associated with higher heat input. The weld produced at a rotational speed of 2000 rpm resulted in improved material mixing, which was indicated by the absence of weld lines and volumetric defects due to the more correct heat input. This welding condition was selected for further mechanical testing. Lap shear testing of PMMA GS/PMMA 6 N/2 wt% SiO₂ nanocomposite single lap joints welded at 2000 rpm resulted in an average ultimate lap shear strength of 3.9 ± 0.05 MPa. These weld strength values are equal to or better than those obtained using state-of-the-art welding techniques for PMMA materials, thereby demonstrating the potential of friction spot welding for thermoplastic nanocomposites.     

Effect of welding parameters on microstructure and mechanical properties of AA6061-T6 butt welded joints by stationary shoulder friction stir welding

Stationary shoulder friction stir welding (SSFSW) butt welded joints were fabricated successfully for AA6061-T6 sheets with 5.0 mm thickness. The welding experiments were performed using 750–1500 rpm tool rotation speeds and 100–300 mm/min welding speeds. The effects of welding parameters on microstructure and mechanical properties for the obtained welds were discussed and analyzed in detail. It is verified that the defect-free SSFSW welds with fine and smooth surface were obtained for all the selected welding parameters, and the weld transverse sections are obviously different from that of conventional FSW joint. The SSFSW nugget zone (NZ) has “bowl-like” shapes with fairly narrow thermal mechanically affected zone (TMAZ) and heat affected zone (HAZ) and the microstructures of weld region are rather symmetrical and homogeneous. The 750–1500 rpm rotation speeds apparently increase the widths of NZ, TMAZ and HAZ, while the influences of 100–300 mm/min welding speeds on their widths are weak. The softening regions with the average hardness equivalent 60% of the base metal are produced on both advancing side and retreating side. The tensile properties of AA6061-T6 SSFSW joints are almost unaffected by the 750–1500 rpm rotation speeds for given 100 mm/min, while the changing of welding speed from 100–300 mm/min for given 1500 rpm obviously increased the tensile strength of the joint and the maximum value for welding parameter 1500 rpm and 300 mm/min reached 77.3% of the base metal strength. The tensile fracture sites always locate in HAZ either on the advancing side or retreating side of the joints.     

Numerical studies of particle segregation in a rotating drum based on Eulerian continuum approach

Solid–solid–gas three-phase particle segregation in a half-filled rotating drum is simulated using Eulerian continuum approach coupling the kinetic theory of granular flow. A dynamic angle of repose fitting (DARF) method is proposed to determine granular kinetic viscosities of particles of six different sizes moving in the drum rotating at 10 rpm, 20 rpm or 30 rpm. The DARF granular kinetic viscosity increases and decreases with the increasing of particle size and drum rotational speed, respectively. The determined DARF granular viscosity values are used to simulate size-induced particle segregation in a rotating drum. The simulated small-particle-rich segregation structure shows a central small-particle-rich band together with two small-particle-rich side wings. The size of the wings decreases with the increasing of the drum rotational speed. The formation of radial segregation core and axial segregation bands qualitatively agree with the experimental observations.     

Microstructure and tensile strength of friction stir welded joints between interstitial free steel and commercially pure aluminium

In the present study, the joining of interstitial free steel and commercial pure aluminium was carried out by friction stir welding (FSW) technique using tool rotational speeds of 600, 900, 1200 rpm and traverse speed of 100 mm/min. The microstructure and micro-hardness of the weld interface have been investigated. Optical microscopy was used to characterize the microstructures of different regions of friction stir welding joints. The scanning electron microscopy-back scattered electron (SEM-BSE) images show the existence of the different reaction layers in the welded zone. The Al₃Fe intermetallic compound has been observed in the weld interface and their thickness increase with the increase in tool rotational speed. Tensile strength was also evaluated and maximum tensile strength of ∼123.2 MPa along with ∼4.5% elongation at fracture of the joint have been obtained when processed at 600 rpm tool rotational speed.     

Microstructure,mechanical and corrosion properties of friction stir welded high nitrogen nickel-free austenitic stainless steel

Friction stir welding (FSW) was applied to a 2.4 mm thick high nitrogen nickel-free austenitic stainless steel plate using tungsten–rhenium (W–Re) tool. The high-quality weld was successfully produced at a tool rotational speed of 400 rpm and a traveling speed of 100 mm/min. The microstructure, mechanical and corrosion properties of the weld were studied. The nitrogen content of the weld was almost identical to that of base metal (BM). FSW refined grains in the stir zone (SZ) through dynamic recrystallization and led to increase in hardness and tensile strength within the SZ, while the ductility was slightly decreased. The failure of tensile specimens occurred in the BM. TEM results revealed precipitates of Cr₂₃C₆ of size ~ 1 μm in the SZ, although their content was small. The precipitation of Cr₂₃C₆ and increase in δ-ferrite in the SZ led to small decrease in both pitting and intergranular corrosion resistance.     

Investigating effects of process parameters on microstructural and mechanical properties of Al5052/SiC metal matrix composite fabricated via friction stir processing

Friction stir processing (FSP) is a novel process for refinement of microstructure, improvement of material’s mechanical properties and production of surface layer composites. In this investigation via friction stir processing, metal matrix composite (MMC) was fabricated on surface of 5052 aluminum sheets by means of 5 μm and 50 nm SiC particles. Influence of tool rotational speed, traverse speed, number of FSP passes, shift of rotational direction between passes and particle size was studied on distribution of SiC particles in metal matrix, microstructure, microhardness and wear properties of specimens. Optimum of tool rotational and traverse speed for achieving desired powder dispersion in MMC was found. Results show that change of tool rotational direction between FSP passes, increase in number of passes and decrease of SiC particles size enhance hardness and wear properties.     

Joint properties of friction welded 6061 aluminum alloy/YSZ–alumina composite at low rotational speed

In this study, a ceramic composite of alumina–yttria stabilized zirconia (YSZ) was friction welded to 6061 aluminum alloy. Alumina rods containing 25 wt.% YSZ were formed using slip casting and subsequently sintered at 1600 °C to form a solid body. The 6061 aluminum alloy sample was cut and polished, and then subjected to friction welding experiments. Both rods were 16 mm in diameter. The results of this study showed that the alumina–25 wt.% YSZ composite was able to be friction welded to 6061 aluminum alloy at a lower rotational speed of 630 rpm compared with high rotational speeds. The friction force was maintained at 5 KN for a frictional time of 30 s. Optical Microscopy (OM) and Field Emission Scanning Electron Microscope (FESEM) were used to analyze the microstructure of the products, particularly at the interface of the joints. The joints were also examined with EDX line and area (energy dispersive X-ray) in order to determine the phases formed during the low speed welding. The mechanical properties including bending strength and Vickers microhardness were measured. The experimental results indicated that the mechanical strength of friction welded alumina–25 wt.% YSZ composite/6061 aluminum alloy components were obviously affected by joining in the low rotational speed (630 rpm), having higher strength as compared to higher rotational speed.     

The effect of tool rotational and traverse speed on friction stir weldability of AISI 430 ferritic stainless steels

In this study, the effects of tool rotational speed and traverse speed on welding of AISI 430 (X6Cr17, material number 1.4016) ferritic stainless steels by friction stir welding method are examined. Two specimens with dimension of 3 × 100 × 200 mm were joined in butt position. Tool rotational speeds were determined to be 560–1400 min⁻¹ and traverse speeds as 80–200 mm/min. During the studies, tool pressure force 3.5 kN and tool angle of 0° was kept constant. Hard metal carbide (WC-Co hard metal identified as K10) with equilateral triangle tip profile was used as the tool material. Determination of the tool advance speeds related to the tool rotation speeds giving the best-looking weld seals with acceptable values of mechanical properties was aimed.During welding of the specimens joined in butt position, the temperature change due to time and variation of the pressure force applied on welded specimens by the tool shoulder has been recorded. It has been observed that the best mechanical resistance values were obtained at tool rotational speed of 1120 min⁻¹ through five tool rotational speeds (560–1400). Also it has been observed that the best mechanical resistance values were obtained at traverse speed of 125 mm/min through five traverse speeds (80–200) with the constant tool pressure force of 3.5 kN and tool angle of 0°.     

Influence of tool geometry and rotational speed on mechanical properties and defect formation in friction stir lap welded 5456 aluminum alloy sheets

Friction stir welding of AA5456 aluminum alloy in lap joint configuration is with two different tempers, T321 and O, and different thicknesses, 5 mm and 2.5 mm was investigated. The influences of tool geometry and various rotational speeds on macrostructure, microstructure and joint strength are presented. Specifically, four different tool pin profiles (a conical thread pin, a cylindrical–conical thread pin, a stepped conical thread pin and Flared Triflute pin tool) and two rotational speeds, 600 and 800 rpm, were used. The results indicated that, tool geometry influences significantly material flow in the nugget zone and accordingly control the weld mechanical properties. Of particular interest is the stepped conical threaded pin, which is introduced for the first time in the present investigation. Scanning electron microscopy investigation of the fracture location of samples was carried out and the findings correlated with tool geometry features and their influences on material flow and tension test results. The optimum microstructure and mechanical properties were obtained for the joints produced with the stepped conical thread pin profile and rotational speed of 600 rpm. The characteristics of the nugget zone microstructure, hooking height, and fracture location of the weld joints were used as criteria to quantify the influence of processing conditions on joint performance and integrity. The results are interpreted in the framework of physical metallurgy properties and compared with published literature.     

A novel approach to develop aluminum matrix nano-composite employing friction stir welding technique

The main object of the present study is to investigate the effect of nano-sized SiC particle on the mechanical properties of the friction stir welding (FSW) joints. Prior to FSW, nano-sized SiC particles were incorporated into the joint line. A combination of three rotational speeds and three traveling speeds were applied. Microstructural evaluation using optical microscopy (OM) and scanning electron microscopy (SEM) revealed a banded structure consisting of particle-rich and particle-free regions in stir zone (SZ). The joints fabricated with rotational speed of 1250 rpm and traveling speeds of 40 and 50 mm/min, exhibited the highest mechanical properties. Owing to the presence of SiC nano-particles, at 1250 rpm and 40 mm/min, ultimate tensile strength (UTS) and percentage of elongation were improved by 31% and 76.1%, respectively. Significant increase in UTS and percentage of elongation were attributed to the pinning effect and increased nucleation sites associated with SiC nano-particles. Moreover, reinforcement particles resulted in breaking of primary grains. On the other hand, at 1250 rpm and 40 mm/min, SiC-included specimen showed superior ductility to SiC-free specimen. The fracture morphologies were in good agreement with corresponding ductility results.     

Effects of tool rotation speed on microstructures and mechanical properties of AA2219-T6 welded by the external non-rotational shoulder assisted friction stir welding

The external non-rotational shoulder assisted friction stir welding (NRSA-FSW) was applied to weld high strength aluminum alloy 2219-T6 successfully, and effects of the tool rotation speed on microstructures and mechanical properties were investigated in detail. Defect-free joints were obtained in a wide range of tool rotation speeds from 600 rpm to 900 rpm, but cavity defects appeared on the advancing side when the tool rotation speed increased to 1000 rpm. The microstructural deformation and heat generation were dominated by the rotating tool pin and sub-size concave shoulder, while the non-rotational shoulder helped to improve the weld formation. Microstructures and Vickers hardness distributions showed that the NRSA-FSW is beneficial to improving the asymmetry and inhomogeneity, especially in the weld nugget zone (WNZ). At the tool rotation speed of 800 rpm, both the tensile strength and the elongation reached the maximum, and the maximum tensile strength was up to 69.0% of the base material. All defect-free joints were fractured at the weakest region with minimum Vickers hardness in the WNZ, while for the joint with cavity defects the fracture occurred at the defect location.     

The optimisation of process parameters for friction stir spot-welded AA3003-H12 aluminium alloy using a Taguchi orthogonal array

The aim of the present work is to optimise the welding parameters for friction stir spot welded non-heat-treatable AA3003-H12 aluminium alloy sheets using a Taguchi orthogonal array. The welding parameters, such as the tool rotational speed, tool plunge depth and dwell time, were determined according to the Taguchi orthogonal table L9 using a randomised approach. The optimum welding parameters for the peak tensile shear load of the joints were predicted, and the individual importance of each parameter on the tensile shear load of the friction stir spot weld was evaluated by examining the signal-to-noise ratio and analysis of variance (ANOVA) results. The optimum levels of the plunge depth, dwell time and tool rotational speed were found to be 4.8 mm, 2 s and 1500 rpm, respectively. The ANOVA results indicated that the tool plunge depth has the higher statistical effect with 69.26% on the tensile shear load, followed by the dwell time and rotational speed. The tensile shear load of the friction stir spot welding (FSSW) joints increased with increasing plunge depth. Additionally, examination of the weld cross-sections, microhardness tests and fracture characterisation of the selected friction spot welded joints were conducted to understand the better performance of the joints. All the fractures of the joints during tensile testing occurred at stir zone (SZ), where the bonded section was minimum. The tensile shear load and tensile deformation of the FSSW joints increased linearly with increasing the bonded size. The finer grain size in the SZ led to the higher hardness, which resulted in higher fracture strength. When the tensile shear load of the joints increased approximately 3-fold, the failure energy absorption of the joints increased approximately 15-fold.     

Characterization of friction stir welded boron carbide particulate reinforced AA6061 aluminum alloy stir cast composite

Development of welding procedures to join aluminum matrix composite (AMCs) holds the key to replace conventional aluminum alloys in many applications. In this research work, AA6061/B₄C AMC was produced using stir casting route with the aid of K₂TiF₆ flux. Plates of 6 mm thickness were prepared from the castings and successfully butt joined using friction stir welding (FSW). The FSW was carried out using a tool rotational speed of 1000 rpm, welding speed of 80 mm/min and axial force of 10 kN. A tool made of high carbon high chromium steel with square pin profile was used. The microstructure of the welded joint was characterized using optical and scanning electron microscopy. The welded joint showed the presence of four zones typically observed in FSW of aluminum alloys. The weld zone showed fine grains and homogeneous distribution of B₄C particles. A joint efficiency of 93.4% was realized under the experimental conditions. But, FSW reduced the ductility of the composite.     

Effect of paddle rotational speed on particle mixing behavior in electrophotographic system by using parallel discrete element method

The objective of this paper is to investigate the effect of paddle rotational speed on the mixing behavior in an agitation process of an electrophotographic system by using parallel DEM. The mixing behaviors of beads with different sizes and densities were measured at various paddle rotational speeds by using a high-speed video camera, and were compared with the simulation results. A good agreement in the mixing behavior was obtained and the changes in particle velocity during the mixing were comparable. The simulation for mixing behavior of larger carrier particles suggested that the radial particle mixing was much faster than the axial one. The faster radial mixing is attributed to the fact that there are two radial flows in the system; the one is over the shaft, the other is between the paddle and shaft. The extent of mixing depended on the number of paddle rotations when the rotational speed is larger than 100 rpm, while the mixing under 50 rpm is completed at a smaller number of rotations.     

Friction stir welded T-joints optimization

The increasing use of aluminium alloys in transportation industry, such as railways, shipbuilding and aeronautics, promotes the development of more efficient and reliable welding processes. Friction stir welding (FSW) is a prominent solid-state joining technology that arose as a possible reliable welding solution. Optimized process parameters are not regularly used in previous studies found in the literature, in particular T-joints, which difficult the process industrial application. This study is focused on the optimization of friction stir welded T-joints using the Taguchi method. Mechanical tests of 27 different welded joints were carried out, and results were analysed using ANOVA, mean effect and response surface methodology (RSM). The tool rotational speed was verified to be the most influent factor in the joint mechanical properties, and is strongly dependent on the shoulder/probe diameters ratio. It was also shown that using 1000 rpm, 3.90 mm of probe depth and shoulder/probe diameters ratio of 2.5 (shoulder diameter of 15 mm) it may be achieved improved joint strength. For the optimized parameters it was verified that the welding speed does not have a significant influence. Equations to predict the joints mechanical properties were also derived through multiple regression.     

Microstructure and interface characterization of dissimilar friction stir welded lap joints between Ti–6Al–4V and AISI 304

The feasibility of dissimilar friction stir welding (FSW) in overlap configuration between Ti–6Al–4V alloy (Ti64) and AISI 304 austenitic stainless steels (304SS) was investigated. Sound joints were achieved when placing titanium as the upper workpiece. Joints were successfully produced by employing a welding speed of 1 mm/s and rotational speeds of 300 and 500 rpm. A lamellar microstructure was formed in the stir zone of Ti64, where grain size was found to increase with increasing rotational speed, and austenitic equiaxed grains were obtained near the interface of 304SS coupon. Energy dispersive X-ray spectroscopy (SEM-EDS) of the interface revealed a thin intermixed region and suggested intermetallic compound formation. Microhardness data in the titanium weld zone for both rotational speeds exhibited slightly lower values than the base material, with the lowest values in the heat affected zone, whereas the microhardness values in the stainless steel side around the weld center were found to be higher than those obtained for the base material.     

Formation and mechanical properties of stationary shoulder friction stir welded 6005A-T6 aluminum alloy

6005A-T6 aluminum alloy is welded by stationary shoulder friction stir welding (SSFSW). At a constant rotational velocity of 2000 rpm, the effect of welding speed on mechanical properties of SSFSW joint are investigated in detail. Defect-free joint with gloss surface and small flash is attained and no cracks appear at the bending angle of 180°. Compared with traditional friction stir welding (FSW), width of rotational shoulder affected zone is relatively small because of the smaller diameter of rotational shoulder. Increasing welding speed is benefit for reducing the width of softening region and the softening degree. The fracture position of welding joint locates in thermo-mechanically affected zone and the fracture surface morphology presents the typical ductile fracture. The maximum tensile strength of joint at the welding speed of 400 mm/min reaches 82% of base metal (BM).     

Evaluation of microstructures and mechanical properties of friction stir welded lap joints of Inconel 600/SS 400

The microstructures and mechanical properties of friction stir welded Inconel 600 and SS 400 lap joints were evaluated in this study. Friction stir welding was carried out at a tool rotation speed of 200 rpm and a welding speed of 100 mm/min. Application of friction stir welding was notably effective in reducing the grain size of the stir zone, as a result, the average grain size of Inconel 600 was reduced from 20 μm in the base material to 8.5 μm in the stir zone. The joint interface between Inconel 600 and SS 400 was soundly welded without voids and cracks, and MC carbides with a size of 50 nm were partially formed in the region of the lap joint interface in Inconel 600. In addition, a hook from SS 400 was formed on the advancing side of the Inconel 600 alloy, which directly affected an increase in the peel strength of the weld. In this study, we systematically discussed the effect of friction stir welding on the evolution of the microstructures and mechanical properties of friction stir lap jointed Inconel 600 and SS 400.