Superior catalytic behaviour of Pt-doped Pd catalysts in the complete oxidation of methane at low temperature

The catalytic combustion of methane at low temperature under lean conditions was investigated over bimetallic palladium-platinum catalysts supported on alumina. Pd-Pt catalysts with constant 2 wt.% metal loading and varying compositions in Pt and Pd were prepared by successive impregnations of the metal salts. The catalysts were characterised by powder X-ray diffraction, transmission electron microscopy/electron dispersion X-ray spectroscopy (TEM/EDX), volumetry of H₂ chemisorption, FTIR study of CO adsorption and temperature-programmed oxidation (TPO). In the absence of water added to the feed, the methane conversion over Pd-rich bimetallic catalysts (Pt/Pt + Pd molar ratios less than 0.3) was found to be the same as that of the reference Pd/Al₂O₃ catalyst. Interestingly, under wet conditions, these bimetallic catalysts exhibited an improved performance with respect to Pd/Al₂O₃. This effect was found to be maintained upon mild steam ageing. An interaction between both metals was suggested to explain the enhanced activity of bimetallic catalysts. This was confirmed by TPO experiments indicating that formation and decomposition of PdO is affected upon Pt addition even for very low amounts of Pt. The adsorption of CO on reduced catalysts studied by FTIR revealed new types of adsorbed CO species, suggesting again an interaction between two metals.     

Stability of palladium-based catalysts during catalytic combustion of methane: The influence of water

The stability of methane conversion was studied over a Pd/Al₂O₃ catalyst and bimetallic Pd–Pt/Al₂O₃ catalysts. The activity of methane combustion over Pd/Al₂O₃ gradually decreased with time, whereas the methane conversion over bimetallic Pd–Pt catalysts was significantly more stable. The differences in combustion behavior were further investigated by activity tests where additional water vapor was periodically added to the feed stream. From these tests it was concluded that water speeds up the degradation process of the Pd/Al₂O₃ catalyst, whereas the catalyst containing Pt was not affected to the same extent. DRIFTS studies in a mixture of oxygen and methane revealed that both catalysts produce surface hydroxyls during combustion, although the steady state concentration on the pure Pd catalyst is higher for a fixed temperature and water partial pressure. The structure of the bimetallic catalyst grains with a PdO domain and a Pd–Pt alloy domain may be the reason for the higher stability, as the PdO domain appears to be more affected by the water generated in the combustion reaction than the alloy. Not all fuels that produce water during combustion will have stability issues. It appears that less strong binding in the fuel molecule will compensate for the degradation.     

Catalytic combustion of methane over bimetallic Pd–Pt catalysts: The influence of support materials

The effect of support material on the catalytic performance for methane combustion has been studied for bimetallic palladium–platinum catalysts and compared with a monometallic palladium catalyst on alumina. The catalytic activities of the various catalysts were measured in a tubular reactor, in which both the activity and stability of methane conversion were monitored. In addition, all catalysts were analysed by temperature-programmed oxidation and in situ XRD operating at high temperatures in order to study the oxidation/reduction properties.

The activity of the monometallic palladium catalyst decreases under steady-state conditions, even at a temperature as low as 470 °C. In situ XRD results showed that no decomposition of bulk PdO into metallic palladium occurred at temperatures below 800 °C. Hence, the reason for the drop in activity is probably not connected to the bulk PdO decomposition.

All Pd–Pt catalysts, independently of the support, have considerably more stable methane conversion than the monometallic palladium catalyst. However, dissimilarities in activity and ability to reoxidise PdO were observed for the various support materials. Pd–Pt supported on Al₂O₃ was the most active catalyst in the low-temperature region, Pd–Pt supported on ceria-stabilised ZrO₂ was the most active between 620 and 800 °C, whereas Pd–Pt supported on LaMnAl₁₁O₁₉ was superior for temperatures above 800 °C. The ability to reoxidise metallic Pd into PdO was observed to vary between the supports. The alumina sample showed a very slow reoxidation, whereas ceria-stabilised ZrO₂ was clearly faster.     

Catalytic combustion of methane over supported bimetallic Pd catalysts: Effects of Ru or Rh addition

A series of Pd/γ-Al₂O₃ catalysts with various amounts of Ru or Rh with, and/or without, BaO were prepared by successive incipient wetness impregnation. The catalysts were investigated for the catalytic methane combustion before, and after, H₂S poisoning in an oxygen-rich atmosphere. The addition of ruthenium enhanced the catalytic activity for methane oxidation even after H₂S poisoning while maintaining the initial catalytic activity of the fresh catalyst. These results are explained in terms of dispersion of palladium by ruthenium and poisoning resistance of ruthenium. The addition of rhodium did not improve the overall activity in methane oxidation.     

Complete methane oxidation over Pd catalyst supported on α-alumina. Influence of temperature and oxygen pressure on the catalyst activity

The influence of the reaction parameters including temperature, oxygen concentration, and of in situ hydrogen reduction on the Pd catalyst activity towards complete methane oxidation is studied experimentally.Zero porosity α-alumina plates are used as a support for Pd catalyst. This lowers the influence of metal–support interaction on the catalyst state as confirmed by UV–visible spectroscopy. A plug flow reactor with a high linear gas velocity is used to measure the reaction rate. Overall conversion is kept low for most of the experiments so that the reaction is in the kinetically limited regime. The oxidation state of the catalyst before and after the reaction is determined using UV–visible reflectance spectroscopy of the plate surface. Changes in the catalyst activity with time are monitored after stepwise changes in the reaction parameters.Activity was found to decrease with time at low temperatures and high oxygen concentrations (condition when PdO phase is stable) and to increase with time at high temperatures and low oxygen concentrations (conditions when Pd is stable). A sharp increase in conversion was observed after the in situ hydrogen reduction of the sample.The experimental data is consistent with the reduced Pd form of the catalyst being more active towards methane oxidation than the oxidized PdO form at high temperatures. Possible particle size and morphology effects are discussed.     

The nature of activity enhancement for propane oxidation over supported Pt catalysts exposed to sulphur dioxide

The nature of the active sites, the role of the support, and the mechanism by which hydrocarbons are activated over supported Pt catalysts have been investigated for the combustion of propane in the presence and absence of SO₂. A strong enhancement in the activity for propane oxidation has been confirmed either when SO₂ is introduced with the propane or with a pre-sulphated alumina-supported catalyst. No equivalent effects were found with silica-supported catalysts. Fluorination of the alumina support also leads to an increase in activity. The addition of pulses of SO₂ into the propane-containing gas stream produces a very large, but short-lived, increase in activity in addition to a more gradual and progressive activity enhancement. Reasons for these different effects are discussed. Attempts to correlate the permanent enhancement in activity with the total acidity of the support were unsuccessful. It appears that the increase in activity is due to a more subtle effect and a model is presented in which the possible role of perimeter sites at the metal–support interface is emphasised.     

Oxidation behaviour and catalytic properties of Pd/Al2O3 catalysts in the total oxidation of methane

A series of Pd/Al₂O₃ catalysts with a wide range of mean Pd particle sizes (ca. 2–30 nm in diameter) was prepared by using various precursors (H₂PdCl₄, Pd(NO₃)₂ and Pd(AcAc)₂) and pre-treatments. The mean particle size of reduced samples was determined by H₂ chemisorption. The catalytic activity in methane oxidation under lean burn conditions was measured. The oxidation of reduced samples was studied at 300 °C. The extent of oxidation was found to decrease with increasing mean particle size. While small particles (<5 nm) oxidised very rapidly, the oxidation of large particles (ca. >15 nm) proceeded via a two-step process, being first fast and then slow. The decomposition of oxide species was studied by temperature-programmed experiments under vacuum. Two distinct oxidised species with different stability were evidenced depending on the particle size. Oxidised species in larger particles were found of lower stability than in smaller ones. A correlation between the existence of distinct types of oxide species and catalytic properties in methane oxidation was discussed.     

Effects of ZrO2/Al2O3 properties on the catalytic activity of Pd catalysts for methane combustion and CO oxidation

Zirconia supported on alumina was prepared and characterized by BET surface area, X-ray diffraction (XRD), X-ray photoelectron spectra (XPS), temperature programmed desorption (TPD), and pulse reaction. 0.2% Pd/ZrO₂/Al₂O₃ catalyst were prepared by incipient wetness impregnation of supports with aqueous solution of Pd(NO₃)₂. The effects of support properties on catalytic activity for methane combustion and CO oxidation were investigated. The results show that ZrO₂ is highly dispersed on the surface of Al₂O₃ up to 10 wt.% ZrO₂, beyond this value tetragonal ZrO₂ is formed. The presence of a small amount of ZrO₂ can increase the surface area, pore volume and acidity of support. CO–TPD results show that the increase of CO adsorption capacity and the activation of CO bond after the presence of ZrO₂ lead to the increase of catalytic activity of Pd catalyst for CO oxidation. CO pulse reaction results indicate that the lattice oxygen of support can be activated at lower temperature following the presence of ZrO₂, but it does not accelerate the activity of 0.2% Pd/ZrO₂/Al₂O₃ for methane combustion. 0.2% Pd/ZrO₂/Al₂O₃ dried at 120 °C shows highest activity for CH₄ combustion, and the activity can be further enhanced following the repeat run. The increase of treatment temperature and pre-reduction can decrease the activity of catalyst for CH₄ combustion.     

Complete Oxidation of Methane at Low Temperature over Pt Catalysts Supported on High Surface Area SnO2

The catalytic activity of Pt catalysts supported on high surface area tin(IV) oxide in the complete oxidation of CH₄ traces under lean conditions at low temperature was studied in the absence and in the presence of water (10 vol.%) or H₂S (100 vol.ppm). Their catalytic properties were compared to those of Pd/Al₂O₃ and Pt/Al₂O₃. In the absence of H₂S in the feed, Pt/SnO₂appears as a very promising catalyst for CH₄ oxidation, being even significantly more active under wet conditions than the best reference catalyst, Pd/Al₂O₃. Catalysts steamed-aged at 873 K were also studied in order to simulate long term ageing in real lean-burn NGV exhaust conditions. To this respect, Pt/SnO₂ is slightly less resistant than Pd/Al₂O₃. In the presence of H₂S, Pt/SnO₂catalysts are rapidly and almost completely poisoned, comparably to Pd/Al₂O₃and the catalytic activity is hardly restored upon oxidising treatment below 773 K. A synergetic effect between Pt and specific surface SnO₂sites active in CH₄oxidation is proposed to explain the superior catalytic behaviour of Pt/SnO₂.     

Catalytic hydrodehalogenation of halon 1211 (CBrClF2) over γ-alumina-supported Ni, Pd and Pt catalysts

The hydrodehalogenation of halon 1211 over Ni, Pd and Pt supported on γ-alumina was studied. The effect of reaction temperature and hydrogen/halon 1211 input ratio was examined. Steady state catalytic activities of Pd and Pt are very similar, and much higher than that of Ni. Hydrodehalogenation over Pd favours the formation of CH₂F₂, while Pt and Ni produce primarily CH₄ and CH₃F, respectively. Product profiles suggest that the hydrodehalogenation of halon 1211 over Pd and Pt follows a reaction mechanism which is similar to hydrodehalogenation of CFC-12. Over Ni catalysts, the primary hydrodehalogenation reactions are those which first remove one halogen (Cl or Br) and then remove two halogens (one F and either Br or Cl). The higher mobility of hydrogen atom on the surface of Pt is consistent with the observation that only trace amounts of C₂₊ hydrocarbons were detected when Pt was used compared with Pd and Ni. Increasing selectivity to CH₂F₂ with time on stream over Pd and Pt is mainly ascribed to the transformation of support alumina to partially fluorinated alumina.     

低负载Pd/Al2O3催化剂的制备及其对CO室温催化性能研究

采用等体积浸渍法和还原法结合制备了Pd/Al2 O3催化剂,通过N2吸附-脱附、SEM、TEM、X射线衍射、X射线光电子能谱和CO原位漫反射傅里叶变换红外光谱等表征手段对制备的样品微观结构进行了系统分析,考察了不同Pd负载量和测试条件下CO催化氧化性能.实验结果表明,水合肼还原法实现了Pd在Al2 O3载体上的均匀分散...     

Selective reduction of NOx by hydrogen and methane in natural gas stationary sources over alumina-supported Pd, Co and Co/Pd catalysts: Part A. On the effect of palladium precursors and catalyst pre-treatment

The aim of the present work is to study the selective reduction of NO_x from natural gas sources. The unburned methane can be used as reductant. Another reductant such as hydrogen can be created in situ, using a microreformer. The results suggest that the NO_x are reduced by H₂ at low temperature, when methane is not activated and at higher temperature the methane is then the main reductant. However, the catalytic behaviour depends on the metal precursor and the catalyst treatment. The most prominent result is obtained on the palladium catalyst prepared from Pd(NH₃)₄(NO₃)₂ precursor. Comparing the reduction and the calcination step in the course of catalyst preparation, one can conclude that calcination lead to the higher activity in deNO_x, since reduced catalysts are oxidized during the deNO_x process.     

Catalytic activity and long-term stability of palladium oxide catalysts for natural gas combustion: Pd supported on LaMnO3-ZrO2

The catalytic activity and long-term stability of 2% Pd/LaMnO₃-ZrO₂ catalysts for natural gas combustion were deeply investigated. The catalyst, prepared via solution combustion synthesis, was completely characterized (XRD, BET, FESEM/EDS, TPC/TPD/TPR and FT-IR analysis) in the fresh status, and in the aged one, after prolonged treatment under hydro-thermal ageing and S-compounds poisoning (up to 3 weeks of hydro-thermal treatment at 800 °C under a flow of domestic boiler exhaust gases typical composition of 9% CO₂, 18% H₂O, 2% O₂ in N₂, including 200 ppmv of SO₂). An increased catalytic activity towards NG combustion with ageing was detected: the T₅₀, in fact, got lowered from 570 (fresh sample) to 465 °C (after 3 weeks ageing). Highly dispersed Pd centers were predominant on fresh catalyst. Upon ageing, oxygen covered Pd metal particles formed, at the expense of dispersed cationic and zerovalent Pd atoms. The increase in the catalytic activity was associated to the phase modification occurring in the bulk support, where Mn oxides, active towards CH₄ combustion, segregated. Moreover, bands due to sulfate species were detected in aged samples: IR analysis showed that Pd atoms did not interact significantly with these species. The bands of sulfate species decreased in intensity after 3 weeks ageing, likely mostly due to sintering of the catalyst, with the corresponding decrease in the surface area.     

Combined CO/CH4 oxidation tests over Pd/Co3O4 monolithic catalyst: Effects of high reaction temperature and SO2 exposure on the deactivation process

CO and CH₄ combined oxidation tests were performed over a Pd (70 g/ft³)/Co₃O₄ monolithic catalyst in conditions of GHSV = 100,000 h⁻¹ and feed composition close to that of emission from bi-fuel vehicles. The effect of SO₂ (5 ppm) on CO and CH₄ oxidation activity under lean condition (λ = 2) was investigated. The presence of sulphur strongly deactivated the catalyst towards methane oxidation, while the poisoning effect was less drastic in the oxidation of CO. Saturation of the Pd/Co₃O₄ catalytic sites via chemisorbed SO₃ and/or sulphates occurred upon exposure to SO₂. A treatment of regeneration to remove sulphate species was attempted by performing a heating/cooling cycle up to 900 °C in oxidizing atmosphere. Decomposition of PdO and Co₃O₄ phases at high temperature, above 750 °C, was observed. Moreover, sintering of Pd⁰ and PdO particles along with of CoO crystallites takes place.