Direct Observation of Conductive Polymer Induced Inversion Layer in n‐Si and Correlation to Solar Cell Performance

Heterojunctions formed by ultrathin conductive polymer [poly(3,4‐ethylenedioxythiophene): poly(styrenesulfonate)—PEDOT:PSS] films and n‐type crystalline silicon are investigated by photoelectron spectroscopy. Large shifts of Si 2p core levels upon PEDOT:PSS deposition provide evidence that a dopant‐free p–n junction, i.e., an inversion layer, is formed within Si. Among the investigated PEDOT:PSS formulations, the largest induced band bending within Si (0.71 eV) is found for PH1000 (high PEDOT content) combined with a wetting agent and the solvent additive dimethyl sulfoxide (DMSO). Without DMSO, the induced band bending is reduced, as is also the case with a PEDOT:PSS formulation with higher PSS content. The interfacial energy level alignment correlates well with the characteristics of PEDOT:PSS/n‐Si solar cells, where high polymer conductivity and sufficient Si‐passivation are also required to achieve high power conversion efficiency.     

Highly Conductive PEDOT:PSS Electrode with Optimized Solvent and Thermal Post‐Treatment for ITO‐Free Organic Solar Cells

Highly conductive poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) films as stand‐alone electrodes for organic solar cells have been optimized using a solvent post‐treatment method. The treated PEDOT:PSS films show enhanced conductivities up to 1418 S cm^?1, accompanied by structural and chemical changes. The effect of the solvent treatment on PEDOT:PSS has been investigated in detail and is shown to cause a reduction of insulating PSS in the conductive polymer layer. Using these optimized electrodes, ITO‐free, small molecule organic solar cells with a zinc phthalocyanine (ZnPc):fullerene C₆₀ bulk heterojunction have been produced on glass and PET substrates. The system was further improved by pre‐heating the PEDOT:PSS electrodes, which enhanced the power conversion efficiency to the values obtained for solar cells on ITO electrodes. The results show that optimized PEDOT:PSS with solvent and thermal post‐treatment can be a very promising electrode material for highly efficient flexible ITO‐free organic solar cells.     

Semiconducting single-walled carbon nanotubes as interfacial modification layers for organic-Si solar cells

A semiconducting single-walled carbon nanotubes (s-SWCNTs) interlayer between poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) and n-Si was used for high performance organic-Si hybrid photovoltaic (PV) devices. The s-SWCNTs films with different thickness were utilized to investigate the PV effect on PEDOT:PSS/Si device performance. The surface potential of Si substrate with s-SWCNTs was dramatically reduced, which increased the compatibility between Si and PEDOT:PSS. In addition, s-SWCNTs with good semiconducting properties, guaranteed the charge transfer between Si and PEDOT:PSS. Therein, the electrical contact was dramatically improved with addition of s-SWCNTs interlayer, which led to increased fill factor. A power conversion efficiency (PCE) of 12.14% was achieved with an optimized thickness of s-SWCNTs layer. The s-SWCNTs interface layer was fabricated by a simple solution processed method, which was easily coupled with organic-Si solar cells to enhance the PCE.     

Photovoltaic Devices: Highly Conductive PEDOT:PSS Electrode with Optimized Solvent and Thermal Post‐Treatment for ITO‐Free Organic Solar Cells (Adv. Funct. Mater. 6/2011)

Highly conductive poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) films as stand‐alone electrodes for organic solar cells have been optimized using a solvent post‐treatment method. The treated PEDOT:PSS films show enhanced conductivities up to 1418 S cm^?1, accompanied by structural and chemical changes. The effect of the solvent treatment on PEDOT:PSS has been investigated in detail and is shown to cause a reduction of insulating PSS in the conductive polymer layer. Using these optimized electrodes, ITO‐free, small molecule organic solar cells with a zinc phthalocyanine (ZnPc):fullerene C₆₀ bulk heterojunction have been produced on glass and PET substrates. The system was further improved by pre‐heating the PEDOT:PSS electrodes, which enhanced the power conversion efficiency to the values obtained for solar cells on ITO electrodes. The results show that optimized PEDOT:PSS with solvent and thermal post‐treatment can be a very promising electrode material for highly efficient flexible ITO‐free organic solar cells.     

Boosting Performance of Non‐Fullerene Organic Solar Cells by 2D g‐C3N4 Doped PEDOT:PSS

The power‐conversion efficiency (PCE) of single‐junction organic solar cells (OSCs) has exceeded 16% thanks to the development of non‐fullerene acceptor materials and morphological optimization of active layer. In addition, interfacial engineering always plays a crucial role in further improving the performance of OSCs based on a well‐established active‐layer system. Doping of graphitic carbon nitride (g‐C₃N₄) into poly(3,4‐ethylene‐dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) as a hole transport layer (HTL) for PM6:Y6‐based OSCs is reported, boosting the PCE to almost 16.4%. After being added into the PEDOT:PSS, the g‐C₃N₄ as a Bronsted base can be protonated, weakening the shield effect of insulating PSS on conductive PEDOT, which enables exposures of more PEDOT chains on the surface of PEDOT:PSS core‐shell structure, and thus increasing the conductivity. Therefore, at the interface between g‐C₃N₄ doped HTL and PM6:Y6 layer, the charge transport is improved and the charge recombination is suppressed, leading to the increases of fill factor and short‐circuit current density of devices. This work demonstrates that doping g‐C₃N₄ into PEDOT:PSS is an efficient strategy to increase the conductivity of HTL, resulting in higher OSC performance.     

Over 16.7% Efficiency Organic‐Silicon Heterojunction Solar Cells with Solution‐Processed Dopant‐Free Contacts for Both Polarities

Realization of synchronous improvement in optical management and electrical engineering is necessary to achieve high‐performance photovoltaic device. However, inherent challenges are faced in organic‐silicon heterojunction solar cells (HSCs) due to the poor contact property of polymer on structured silicon surface. Herein, a remarkable efficiency boost from 12.6% to over 16.7% in poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate)/n‐silicon (PEDOT:PSS/n‐Si) HSCs by independent optimization of hole‐/electron‐selective contacts only relying on solution‐based processes is realized. A bilayer PEDOT:PSS film with different functionalizations is utilized to synchronously realize conformal contact and effective carrier collection on textured Si surface, making the photogenerated carriers be well separated at heterojunction interface. Meanwhile, fullerene derivative is used as electron‐transporting layer at the rear n‐Si/Al interface to reduce the contact barrier. The study of carriers' transport and independent optimization on separately contacted layers may lead to an effective and simplified path to fabricate high‐performance organic‐silicon heterojunction devices.     

Junction model and transport mechanism in hybrid PEDOT:PSS/n-GaAs solar cells

This study investigates the junction formation and interface properties of PEDOT:PSS/n-GaAs hybrid solar cells on planar GaAs substrates. Barrier height, photocurrent, dark saturation current and build-in potential at this hybrid interface are measured by varying n-GaAs doping concentrations. The work function and valence band edge of the polymer are extracted from ultraviolet photoelectron spectroscopy to construct the band diagram of the hybrid n-GaAs/PEDOT:PSS junction. The current-voltage characteristics were analyzed by using abrupt (p⁺n) junction and Schottky junction models. Contrary to the earlier results from the PEDOT:PSS/n-Si solar cells, the experimental evidence clearly suggested that the interface between n-GaAs and PEDOT:PSS more likely exhibited a Schottky type instead of a p⁺n junction. The current transport is governed by the thermionic emission of majority carriers over a barrier and not by diffusion. The dark saturation current density increases markedly owing to the increasing surface recombination rate in heavier n-doped GaAs substrates, leading to significant deterioration in solar cells performance.     

Efficient and Stable Perovskite Solar Cells via Dual Functionalization of Dopamine Semiquinone Radical with Improved Trap Passivation Capabilities

Highly efficient planar heterojunction perovskite solar cells (PVSCs) with dopamine (DA) semiquinone radical modified poly(3,4‐ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) (DA‐PEDOT:PSS) as a hole transporting layer (HTL) were fabricated. A combination of characterization techniques were employed to investigate the effects of DA doping on the electron donating capability of DA‐PEDOT:PSS, perovskite film quality and charge recombination kinetics in the solar cells. Our study shows that DA doping endows the DA‐PEDOT:PSS‐modified PVSCs with a higher radical content and greater perovskite to HTL charge extraction capability. In addition, the DA doping also improves work function of the HTL, increases perovskite film crystallinity, and the amino and hydroxyl groups in DA can interact with the undercoordinated Pb atoms on the perovskite crystal, reducing charge‐recombination rate and increasing charge‐extraction efficiency. Therefore, the DA‐PEDOT:PSS‐modified solar cells outperform those based on PEDOT:PSS, increasing open‐circuit voltage (V _oc) and power conversion efficiency (PCE) to 1.08 V and 18.5%, respectively. Even more importantly, the efficiency of the unencapsulated DA‐PEDOT:PSS‐based PVSCs are well retained with only 20% PCE loss after exposure to air for 250 hours. These in‐depth insights into structure and performance provide clear and novel guidelines for the design of effective HTLs to facilitate the practical application of inverted planar heterojunction PVSCs.     

High efficiency arrays of polymer solar cells fabricated by spray‐coating in air

We present bulk heterojunction organic solar cells fabricated by spray‐casting both the PEDOT:PSS hole‐transport layer (HTL) and active PBDTTT‐EFT:PC₇₁BM layers in air. Devices were fabricated in a (6 × 6) array across a large‐area substrate (25 cm²) with each pixel having an active area of 6.45 mm². We show that the film uniformity and operational homogeneity of the devices are excellent. The champion device with spray cast active layer on spin cast PEDOT:PSS had an power conversion efficiency (PCE) of 8.75%, and the best device with spray cast active layer and PEDOT:PSS had a PCE of 8.06%. The impacts of air and light exposure of the active layer on device performance are investigated and found to be detrimental. Copyright © 2015 John Wiley & Sons, Ltd.     

Solution‐Processed Nickel Oxide Hole Transport Layers in High Efficiency Polymer Photovoltaic Cells

The detailed characterization of solution‐derived nickel (II) oxide (NiO) hole‐transporting layer (HTL) films and their application in high efficiency organic photovoltaic (OPV) cells is reported. The NiO precursor solution is examined in situ to determine the chemical species present. Coordination complexes of monoethanolamine (MEA) with Ni in ethanol thermally decompose to form non‐stoichiometric NiO. Specifically, the [Ni(MEA)₂(OAc)]⁺ ion is found to be the most prevalent species in the precursor solution. The defect‐induced Ni³⁺ ion, which is present in non‐stoichiometric NiO and signifies the p‐type conduction of NiO, as well as the dipolar nickel oxyhydroxide (NiOOH) species are confirmed using X‐ray photoelectron spectroscopy. Bulk heterojunction (BHJ) solar cells with a polymer/fullerene photoactive layer blend composed of poly‐dithienogermole‐thienopyrrolodione (pDTG‐TPD) and [6,6]‐phenyl‐C71‐butyric acid methyl ester (PC₇₁BM) are fabricated using these solution‐processed NiO films. The resulting devices show an average power conversion efficiency (PCE) of 7.8%, which is a 15% improvement over devices utilizing a poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) HTL. The enhancement is due to the optical resonance in the solar cell and the hydrophobicity of NiO, which promotes a more homogeneous donor/acceptor morphology in the active layer at the NiO/BHJ interface. Finally, devices incorporating NiO as a HTL are more stable in air than devices using PEDOT:PSS.     

High Efficiency Planar p‐i‐n Perovskite Solar Cells Using Low‐Cost Fluorene‐Based Hole Transporting Material

For commercial applications, it is a challenge to find suitable and low‐cost hole‐transporting material (HTM) in perovskite solar cells (PSCs), where high efficiency spiro‐OMeTAD and PTAA are expensive. A HTM based on 9,9‐dihexyl‐9H‐fluorene and N,N‐di‐p‐methylthiophenylamine (denoted as FMT) is designed and synthesized. High‐yield FMT with a linear structure is synthesized in two steps. The dopant‐free FMT‐based planar p‐i‐n perovskite solar cells (pp‐PSCs) exhibit a high power conversion efficiency (PCE) of 19.06%, which is among the highest PCEs reported for the pp‐PSCs based on organic HTM. For comparison, a PEDOT:PSS HTM‐based pp‐PSC is fabricated under the same conditions, and its PCE is found to be 13.9%.     

In‐Situ Switching from Barrier‐Limited to Ohmic Anodes for Efficient Organic Optoelectronics

Injection and extraction of charges through ohmic contacts are required for efficient operation of semiconductor devices. Treatment using polar non‐solvents switches polar anode surfaces, including PEDOT:PSS and ITO, from barrier‐limited hole injection and extraction to ohmic behaviour. This is caused by an in‐situ modification of the anode surface that is buried under a layer of organic semiconductor. The exposure to methanol removes polar hydroxyl groups from the buried anode interface, and permanently increases the work function by 0.2–0.3 eV. In the case of ITO/PEDOT:PSS/PBDTTT‐CT:PC71BM/Al photovoltaic devices, the higher work function promotes charge transfer, leading to p‐doping of the organic semiconductor at the interface. This results in a two‐fold increase in hole extraction rates which raises both the fill factor and the open‐circuit voltage, leading to high power conversion efficiency of 7.4%. In ITO/PEDOT:PSS/F8BT/Al polymer light‐emitting diodes, where the organic semiconductor's HOMO level lies deeper than the anode Fermi level, the increased work function enhances hole injection efficiency and luminance intensity by 3 orders of magnitude. In particular, hole injection rates from PEDOT:PSS anodes are equivalent to those achievable using MoO₃. These findings exemplify the importance of work function control as a tool for improved electrode design, and open new routes to device interfacial optimization using facile solvent processing techniques. Such simple, persistent, treatments pave the way towards low cost manufacturing of efficient organic optoelectronic devices.     

A Versatile Fluoro‐Containing Low‐Bandgap Polymer for Efficient Semitransparent and Tandem Polymer Solar Cells

The versatility of a fluoro‐containing low band‐gap polymer, poly[2,6‐(4,4‐bis(2‐ethylhexyl)‐4H‐cyclopenta[2,1‐b;3,4‐b’]dithiophene)‐alt‐4,7‐(5‐fluoro‐2,1,3‐benzothia‐diazole)] (PCPDTFBT) in organic photovoltaics (OPVs) applications is demonstrated. High boiling point 1,3,5‐trichlorobenzene (TCB) is used as a solvent to manipulate PCPDTFBT:[6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) active layer morphology to obtain high‐performance single‐junction devices. It promotes the crystallization of PCPDTFBT polymer, thus improving the charge‐transport properties of the active layer. By combining the morphological manipulation with interfacial optimization and device engineering, the single‐junction device exhibits both good air stability and high power‐conversion efficiency (PCE, of 6.6%). This represents one of the highest PCE values for cyclopenta[2,1‐b;3,4‐b’]dithiophene (CPDT)‐based OPVs. This polymer is also utilized for constructing semitransparent solar cells and double‐junction tandem solar cells to demonstrate high PCEs of 5.0% and 8.2%, respectively.     

Tuning Hole Transport Layer Using Urea for High‐Performance Perovskite Solar Cells

Interface engineering is critical to the development of highly efficient perovskite solar cells. Here, urea treatment of hole transport layer (e.g., poly(3,4‐ethylene dioxythiophene):polystyrene sulfonate (PEDOT:PSS)) is reported to effectively tune its morphology, conductivity, and work function for improving the efficiency and stability of inverted MAPbI₃ perovskite solar cells (PSCs). This treatment has significantly increased MAPbI₃ photovoltaic performance to 18.8% for the urea treated PEDOT:PSS PSCs from 14.4% for pristine PEDOT:PSS devices. The use of urea controls phase separation between PEDOT and PSS segments, leading to the formation of a unique fiber‐shaped PEDOT:PSS film morphology with well‐organized charge transport pathways for improved conductivity from 0.2 S cm^?1 for pristine PEDOT:PSS to 12.75 S cm^?1 for 5 wt% urea treated PEDOT:PSS. The urea‐treatment also addresses a general challenge associated with the acidic nature of PEDOT:PSS, leading to a much improved ambient stability of PSCs. In addition, the device hysteresis is significantly minimized by optimizing the urea content in the treatment.     

Graphene‐Conducting Polymer Hybrid Transparent Electrodes for Efficient Organic Optoelectronic Devices

To achieve the broad utilization of the full functionality of graphene (GR) in devices, a transfer method should be developed that can simplify the process without leaving residue of the insulating supporting layer on the surface of GR. Furthermore, stable GR doping without the use of an insulating polymer is required. Here, a new GR transfer method that uses a popular conducting polymer, poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS), is reported as a new supporting layer for the transfer of GR films that are synthesized by chemical vapor deposition. The GR/PEDOT:PSS bilayer can be directly utilized without the removal process. Therefore, this transfer method simplifies the transfer process and solves the residue problem of conventional transfer methods. The stable doping of GR films is simultaneously achieved by using the PEDOT:PSS layer. The new GR/PEDOT:PSS hybrid electrodes are fully functional in polymer solar cells and polymer light‐emitting diodes, outperforming the conventionally transferred GR electrodes and indium tin oxide electrodes.     

Aging process of PEDOT:PSS dispersion and robust recovery of aged PEDOT:PSS as a hole transport layer for organic solar cells

Conducting p-type polymer of poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) has been widely used for organic optoelectronics, particularly as a hole transport layer for organic solar cells. While the aged PEDOT:PSS dispersion impacts device performance, the aging of PEDOT:PSS dispersion have not been well investigated. Moreover, the recovery process of aged (two-year-old) PEDOT:PSS dispersion has not been demonstrated yet. Herein, it is found that aqueous PEDOT:PSS dispersion undergoes extensive phase separation during the aging process, resulting in both nanoscale and macroscale hydrophobic PEDOT-rich agglomerates. When the aged PEDOT:PSS thin film is integrated into P3HT:PCBM organic solar cells, the PEDOT-rich agglomerates trap the photogenerated holes at the PEDOT:PSS/P3HT interface, resulting in poor extraction efficiency in organic solar cells. To recover a hole transport functionality from aged PEDOT:PSS, three different solvents such as isopropyl alcohol (C₃H₇OH), ethanol (C₂H₅OH) and methanol (CH₃OH) are investigated. Among them, it is found that isopropyl alcohol (IPA) yielded very uniform PEDOT:PSS thin film layer. This is because hydrophobic functional groups of IPA solvent facilitated the preferential solvation of phase separated hydrophobic PEDOT-rich agglomerates. However, when non-optimal concentration of IPA solvents was added into the aged PEDOT:PSS dispersion, the size of PEDOT-rich agglomerates was adversely enlarged. When organic solar cells were fabricated using more than a two-year-old PEDOT:PSS that was treated with IPA solvent, the resulting device performance of organic solar cells was fully recovered and became comparable or better than that of organic solar cells fabricated with fresh PEDOT:PSS.     

Isopropanol-treated PEDOT:PSS as electron transport layer in polymer solar cells

Isopropanol (IPA)-treated poly(3,4-ethylenedioxithiophene):poly(styrene sulfonate) (PEDOT:PSS) was applied as a new electron transport layer (ETL) in P3HT:PCBM bulk heterojunction polymer solar cell (BHJ-PSC) devices for the first time, revealing the electron transport property of IPA-treated PEDOT:PSS in sharp contrast to the well known hole transport property of the untreated PEDOT:PSS. Under the optimized condition for incorporating PEDOT:PSS ETL, the power conversion efficiency (PCE) of the ITO/untreated PEDOT:PSS (HTL)/P3HT:PCBM/IPA-treated PEDOT:PSS (ETL)/Al device (3.09%) is quite comparable to that of the reference ITO/untreated PEDOT:PSS (HTL)/P3HT:PCBM/Al device without any ETL (3.06%), and an annealing treatment of PEDOT:PSS ETL at 120 °C for 10 min led to a PCE of 3.25%, which even slightly surpasses that of the reference device, revealing the electron transport property of IPA-treated PEDOT:PSS. The electron transport property of IPA-treated PEDOT:PSS is interpreted by the lowering of the work function of PEDOT:PSS upon IPA treatment and incorporation as ETL as probed by scanning Kelvin probe microscopy (SKPM).     

Revealing the Impact of F4‐TCNQ as Additive on Morphology and Performance of High‐Efficiency Nonfullerene Organic Solar Cells

Fluorinated molecule 2,3,5,6‐tetrafluoro‐7,7,8,8‐tetracyanoquinodimethane (F4‐TCNQ) and its derivatives have been used in polymer:fullerene solar cells primarily as a dopant to optimize the electrical properties and device performance. However, the underlying mechanism and generality of how F4‐TCNQ affects device operation and possibly the morphology is poorly understood, particularly for emerging nonfullerene organic solar cells. In this work, the influence of F4‐TCNQ on the blend film morphology and photovoltaic performance of nonfullerene solar cells processed by a single halogen‐free solvent is systematically investigated using a set of morphological and electrical characterizations. In solar cells with a high‐performance polymer:small molecule blend FTAZ:IT‐M, F4‐TCNQ has a negligibly small effect on the molecular packing and surface characteristics, while it clearly affects the electronic properties and mean‐square composition variation of the bulk. In comparison to the control devices with an average power conversion efficiency (PCE) of 11.8%, inclusion of a trace amount of F4‐TCNQ in the active layer has improved device fill factor and current density, which has resulted into a PCE of 12.4%. Further increase in F4‐TCNQ content degrades device performance. This investigation aims at delineating the precise role of F4‐TCNQ in nonfullerene bulk heterojunction films, and thereby establishing a facile approach to fabricate highly optimized nonfullerene solar cells.     

Rational Interface Design and Morphology Control for Blade‐Coating Efficient Flexible Perovskite Solar Cells with a Record Fill Factor of 81%

Halide perovskites are one of the ideal photovoltaic materials for constructing flexible solar devices due to relatively high efficiencies for low‐temperature solution‐processed devices. However, the overwhelming majority of flexible perovskite solar cells are produced using spin coating, which represents a major hurdle for upscaling. Here, a scalable approach is reported to fabricate efficient and robust flexible perovskite solar cells on a polymer substrate. Thiourea is introduced into perovskite precursor solution to modulate the crystal growth, resulting in dense and uniform perovskite thin films on rough surfaces. As a decisive step, a cascade energy alignment is realized for the hole extraction layer by rationally designing a bilayer interface comprised of PEDOT:PSS/PTAA with a distinct offset in the highest occupied molecular orbital levels, enabling markedly enhanced charge extraction and spectral response. An efficiency as high as 19.41% and a record fill factor up to 81% are achieved for flexible perovskite devices processed by a scalable printing method. Equally important, the bilayer interface reinforces the bendability of the indium tin oxide substrate, leading to enhanced mechanical robustness of the flexible devices. These results underpin the importance of morphology control and interface design in constructing high‐performance flexible perovskite solar cells.