Polyurethanes based on 2,2‐Dinitropropane‐1,3‐diol and 2,2‐bis(azidomethyl)propane‐1,3‐diol as potential energetic binders

On the base of 2,2‐bis(azidomethyl)propane‐1,3‐diol (BAMP) and 2,2‐dinitropropane‐1,3‐diol (DNPD) four different polyurethanes were synthesized in a polyaddition reaction using hexamethylene diisocyanate (HMDI) and diisocyanato ethane (DIE). The obtained prepolymers were mainly characterized using vibrational spectroscopy (IR) and elemental analysis. For determination of low and high temperature behavior, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were used. Investigations concerning friction and impact sensitivities were carried out using a BAM drop hammer and friction tester. The energetic properties of the polymers were determined using bomb calorimetric measurements and calculated with the EXPLO5 V6.02 computer code. The obtained values were compared with the glycidyl azide polymer (GAP). The compounds turned out to be insensitive toward friction (>360 N) and less sensitive toward impact (40 J). The good physical stabilities, along with their sufficient thermal stability (170–210 °C) and moderate energetic properties renders these polymers into potential compounds for applications as binders in energetic formul;ations. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43991.     

2,2‐Dinitro‐1,3‐Bis‐Nitrooxy‐Propane (NPN): A New Energetic Plasticizer

A new energetic plasticizer, 2,2‐dinitro‐1,3‐bis‐nitrooxy‐propane (NPN), has been characterized. Its high oxygen balance, +12.5%, and low glass transition temperature, −81.5 °C (midpoint), makes it very attractive as an energetic plasticizer in solid propellants. The ability of NPN to lower the glass transition temperature and viscosity of uncured PolyNIMMO has been studied and compared to other energetic plasticizers, such as BDNPA/F and butyl‐NENA. NPN has a similar plasticizing effect as butyl‐NENA, both on depressing the glass transition temperature and lowering the viscosity. To increase the poor thermal stability of NPN, several conventional nitrocellulose/nitroglycerine stabilizers were evaluated. Further work is however needed to find a more effective stabilizer.     

Understanding the Compatibility of the Energetic Binder PolyNIMMO with Energetic Plasticizers: Experimental and DFT Studies

The development of energetic binders with suitable energetic plasticizers is required to enhance the mechanical properties and to reduce the glass transition temperature of propellant and explosive formulations. The compatibility of the energetic binder poly(3‐nitratomethyl‐3‐methyloxetane) (polyNIMMO) with five different energetic plasticizers viz. bis(2,2‐dinitro propyl)acetal (BDNPA), dinitro‐diaza‐alkanes (DNDA‐57), 1,2,4‐butanetriol trinitrate (BTTN), N‐N‐butyl‐N ‘(2‐nitroxy‐ethyl) nitramine (BuNENA) and diethyleneglycoldinitrate (DEGDN) was studied by differential scanning calorimetry (DSC), rheology, and DFT methods. The results obtained for the pure binder were compared with the results obtained for the binder/plasticizer blend in regard of the decomposition temperature and the format of the peak indicated the compatibility of polyNIMMO with the plasticizers. The glass transition temperatures of the blends were determined by low temperature DSC and showed desirable lowering of glass transition temperature with single peak. The rheological evaluation revealed that the viscosity of the binder is considerably lowered by means of flow behavior upon addition of 20 % (w/w) plasticizer. The addition of BuNENA and DEGDN has maximum effect on the lowering of viscosity of polyNIMMO. The predicted relative trend of interaction energies between plasticizer and binder is well correlated with the corresponding trend of viscosity of binder/plasticizer blends. These experimental studies verified by theoretical methods are valuable to design practical blends of new plasticizers and binders.     

Poly(1,3‐disila‐1,3‐diphenyl‐2‐oxaindane)‐diphenylsiloxane‐poly(dimethylsiloxane) block copolymers

The heterofunctional condensation of 1,3‐dichloro‐1,3‐disila‐1,3‐diphenyl‐2‐oxaindane with dihydroxydiphenylsilane at various ratios of initial compounds in the presence of amines was carried out, and α,ω‐dihydroxy(1,3‐disila‐1,3‐diphenyl‐2‐oxaindane)‐diphenylsiloxane oligomers with various degrees of condensation were obtained. Corresponding block copolymers were obtained by heterofunctional polycondensation of synthesized α,ω‐dihydroxy(1,3‐disila‐1,3‐diphenyl‐2‐oxaindane)‐diphenylsiloxane oligomers with α,ω‐dichlorodimethylsiloxanes in the presence of amines. Thermogravimetry, gel permeation chromatography, differential scanning calorimetry, and wide‐angle X‐ray analysis were carried out on the synthesized block coplymers. Differential scanning calorimetry and wide‐angle X‐ray studies of these copolymers showed that their properties were determined by the ratio of the lengths of the flexible linear poly(dimethylsiloxane) and rigid poly(1,3‐disila‐1,3‐diphenyl‐2‐oxaindane)‐diphenylsiloxane fragments in the main macromolecular chain. Two‐phase systems were obtained with specific flexible and rigid fragment length values in synthesized block copolymers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3462–3467, 2006     

Synthesis of formaldehyde polymers from benzene‐1,2‐diol,phenolic alkane‐1,2‐diol,and phenolic alkane‐1,3‐diol as immobilized chelatants for borate anion

A variety of phenolic aryl‐1,2‐ and 1,3‐diols have been condensed with formaldehyde to form polymers serving as immobilized chelatants for borate anions. In this way, polymers from 1,2‐dihydroxybenzene, 2‐hydroxymethylphenol, and a 3‐methyl derivative (saligenins) and 2‐(4‐hydroxyphenyl)‐propane‐1,3‐diol have been converted into formaldehyde polymers with an increasing level of conformational mobility in the diol moiety of the polymer. The extraction of borate from alkaline solutions with three types of polymers has been examined, and the polymer containing planar 1,2‐dihydroxybenzene has been found to be superior to a saligenin‐ and 2‐(4‐hydroxyphenyl)‐ propane‐1,3‐diol‐derived polymer. This suggests that conformational mobility is not an important structural feature. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and application of an alternative plasticizer Di(2‐Ethylhexyl)‐1,2‐cyclohexane dicarboxylate

Cyclohexane dicarboxylic acid esters are environmentally friendly and non‐toxic plasticizers, and have similar performance with phthalates which have potential toxicity to human health. In this article, di(2‐ethylhexyl)‐1,2‐cyclohexane dicarboxylate (DEHCH) was synthesized via esterification between hexahydrophthalic anhydride (HHPA) with iso‐octanol by using concentrated sulfuric acid as a catalyst. The effects of reaction parameters on esterification were studied by investigating the temperature, reaction time, molar ratio of iso‐octanol‐to‐HHPA, and catalyst content. Conversions of HHPA to esters were determined. Functional group analysis was conducted by using FTIR and ¹H‐NMR spectroscopy. PVC compounds after addition of the synthesized plasticizer DEHCH presented similar plasticizing performance with DEHP and DINCH, as demonstrated by comparisons of the results of mechanical properties, transparency, and volatilization and migration tests obtained for plasticized PVC compounds. DEHCH can also be considered as an alternative plasticizer for DEHP. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39763.     

Dialkyl furan‐2,5‐dicarboxylates,epoxidized fatty acid esters and their mixtures as bio‐based plasticizers for poly(VInylchloride)

Dialkyl furan‐2,5‐dicarboxylates and epoxidized fatty acid esters (EFAE) of varying molecular weights and volatilities, as well as their mixtures, were investigated as alternative plasticizers for poly(vinylchloride) (PVC). The EFAE utilized were epoxidized soybean oil (ESO) and epoxidized fatty acid methyl ester (e‐FAME). All plasticizers were compatible with PVC, with plasticization efficiencies usually increasing with decreasing molecular weights of the plasticizers (except in the case of ESO, which was remarkably effective at plasticizing PVC, in spite of its relatively high molecular weight). In comparison with phthalate and trimellitate plasticizers, the alternatives generally yielded improved balance of flexibility and retention of mechanical properties after heat aging, with particularly outstanding results obtained using 30?50 wt % e‐FAME in mixtures with diisotridecyl 2,5‐furandicarboxylate. Although heat aging characteristics of the plasticized polymer were often related to plasticizer volatilities, e‐FAME performed better than bis(2‐ethylhexyl) 2,5‐furandicarboxylate, and bis(2‐ethylhexyl) phthalate of comparatively higher molecular weights. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42382.     

An Azido Ester Plasticizer, 1,3‐Di(Azidoacetoxy)‐2,2‐Di(Azidomethyl)Propane (PEAA): Synthesis,Characterization and Thermal Properties

A polyazido compound, 1,3‐di(azidoacetoxy)‐2,2‐di(azidomethyl)propane (PEAA) was synthesized and identified. Thermal properties of PEAA, such as the glass transition temperature (T_g), differential scanning calorimetry (DSC) and thermogravimetric analysis (DTG) were investigated in detail. Two steps in the course of thermal decomposition of PEAA were observed clearly, and some gases, carbon monoxide, carbon dioxide, nitrogen, hydrocyanic acid, methane and 2‐methyl‐1,3‐butadiene were identified as decomposition products by in situ cell FTIR. The pyrolysis mechanism was also proposed.     

Preparation and characterization of castor oil‐based waterborne polyurethane crosslinked with 2‐amino‐2‐(hydroxymethyl)‐1,3‐propanediol

Crosslinked castor oil (CO)‐based waterborne polyurethane was synthesized from CO, polycarbonate diol, isophorone diisocyanate, 2,2‐dimethylol propionic acid, and 2‐amino‐2‐(hydroxymethyl)‐1,3‐propanediol (THAM) using pre‐polymer process. Fourier transform infrared spectroscopy, X‐ray diffraction, and transmission electron microscopy were utilized to characterize the above‐synthesized polyurethane. The effect of THAM content was studied on particle size, zeta potential, thermogravimetric analysis, differential scanning calorimetry, tensile tests, and contact angle measurement. Results showed that, with the increase of THAM content, the particle size increases and the thermal stability increases. Furthermore, as the THAM content increased from 0% to 1.5%, tensile strength increased from 9.5 to 16.3 MPa, contact angle increased from 67.8° to 87.4°, and bibulous rate decreased from 13.4% to 6.1%, the elongation at break dropped from 154.8% to 37.9%, respectively. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45532.     

A study on the aliphatic energetic plasticizers containing nitrate ester and nitramine

The aliphatic energetic plasticizers with three and four –CH₂ between nitrate ester and nitramine were synthesized to obtain a plasticizer that is more stable than N-butyl-N-nitratoethyl nitramine (BuNENA) with two –CH₂. First, amino alcohol compounds such as propylamino propanol (PAP) and ethylamino butanol (EAB) as a precursor of energetic plasticizer were synthesized. However, unlike in BuNENA synthesis, various side reactions occurred in the nitration of amino alcohols. Fortunately, it was possible to considerably suppress the formation of side products in the nitration of PAP by using a solvent and an appropriate concentration of nitric acid. In addition, an energetic plasticizer with higher oxygen content was obtained through the nitration of intermediate, amide alcohol, which was formed in the synthesis of EAB.     

Nonlinear optical studies on new conjugated poly{2,2l‐(3,4‐ dialkoxythiophene‐2,5‐diyl) bis[5‐(2‐thienyl)‐1,3,4‐oxadiazole]}s

Three new donor–acceptor type poly{2,2^l‐(3,4‐ dialkoxythiophene‐2,5‐diyl)bis[5‐(2‐thienyl)‐1,3,4‐oxadiazole]}s ( P1, P2, and P3 ) were synthesized starting from thiodiglycolic acid and diethyl oxalate through multistep reactions. The polymerization was carried out using chemical polymerization technique. The optical and charge‐transporting properties of the polymers were investigated by UV‐visible, fluorescence emission spectroscopic and cyclic voltammetric studies. The polymers showed bluish‐green fluorescence in solutions. The electrochemical band gaps were determined to be 2.03, 2.09, and 2.17 eV for P1 , P2, and P3, respectively. The nonlinear optical properties of new polymers were investigated at 532 nm using single beam Z‐scan and degenerate four‐wave mixing (DFWM) techniques with nanosecond laser pulses. The polymers exhibited strong optical limiting behavior due to “effective” three‐photon absorption. Values of the effective three‐photon absorption ( 3PA ) coefficients, third‐order nonlinear susceptibilities (χ⁽³⁾), and figures (F) of merit were calculated. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Smokeless GAP‐RDX Composite Rocket Propellants Containing Diaminodinitroethylene (FOX‐7)

Composite rocket propellants prepared from nitramine fillers (RDX or HMX), glycidyl azide polymer (GAP) binder and energetic plasticizers are potential substitutes for smokeless double‐base propellants in some rocket motors. In this work, we report GAP‐RDX propellants, wherein the nitramine filler has been partly or wholly replaced by 1,1‐diamino‐2,2‐dinitroethylene (FOX‐7). These smokeless propellants, containing 60% energetic solids and 15% N‐butyl‐2‐nitratoethylnitramine (BuNENA) energetic plasticizer, exhibited markedly reduced shock sensitivity with increasing content of FOX‐7. Conversely, addition of FOX‐7 reduced the thermochemical performance of the propellants, and samples without nitramine underwent unsteady combustion at lower pressures (no burn rate catalyst was added). The mechanical characteristics were quite modest for all propellant samples, and binder‐filler interactions improved slightly with increasing content of FOX‐7. Overall, FOX‐7 remains an attractive, but less than ideal, substitute for nitramines in smokeless GAP propellants.     

Synthesis and characterization of novel aromatic poly(amide‐imide)s derived from 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl or 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl and various aromatic diamines

New aromatic diimide‐dicarboxylic acids having kinked and cranked structures, 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl (2a) and 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl (2b), were synthesized by the reaction of trimellitic anhydride with 2,2′‐bis(4‐aminophenoxy)biphenyl (1a) and 2,2′‐bis(4‐aminophenoxy)‐1,1′‐binaphthyl (1b), respectively. Compounds 2a and 2b were characterized by FT‐IR and NMR spectroscopy and elemental analyses. Then, a series of novel aromatic poly(amide‐imide)s were prepared by the phosphorylation polycondensation of the synthesized monomers with various aromatic diamines. Owing to structural similarity, and a comparison of the characterization data, a model compound was synthesized by the reaction of 2b with aniline. The resulting polymers with inherent viscosities of 0.58–0.97 dl g^?1 were obtained in high yield. The polymers were fully characterized by FT‐IR and NMR spectroscopy. The ultraviolet λ_max values of the poly(amide‐imide)s were also determined. The polymers were readily soluble in polar aprotic solvents. They exhibited excellent thermal stabilities and had 10% weight loss at temperatures above 500 °C under a nitrogen atmosphere. Copyright © 2003 Society of Chemical Industry     

Bishydrazinium and Diammonium Salts of 4,4′,5,5′‐Tetranitro‐2,2′‐biimidazolate (TNBI): Synthesis and Properties

The diammonium ( 1 ) and bishydrazinium ( 2 ) salts of 4,4′,5,5′‐tetranitro‐2,2′‐biimidazolate (TNBI) were synthesized and their physical properties as well as predicted explosive performance characteristics are described. These dianionic salts are easily formed in good yields by reaction of TNBI with aqueous solutions of the cationic species. TNBI is synthesized from 2,2′‐biimidazole, which is ultimately synthesized by the condensation of aqueous glyoxal with ammonium acetate. The compounds were characterized by NMR spectroscopy, vibrational (FT‐IR and Raman) spectroscopy, elemental analysis, thermal analysis (DSC, VTS and calorimetry), and small scale safety testing (impact, friction, ESD). The measured densities and heats of formation are reported. The materials show promise for use in IM explosive and propellant formulations due to the combination of their calculated performances, thermal stability and insensitivity to stimuli.     

X‐Ray reflectivity study of polyimide thin films swollen by 1,3‐butadiene and n‐butane

X‐ray reflectivity measurements were performed on two different polyimide thin films synthesized from 2,2‐bis(3,4‐carboxyphenyl)hexafluoropropane dianhydride (6FDA) in 1,3‐butadiene and n‐butane. In 1,3‐butadiene at 2.3 atm, the film thickness increased by 24–30%. However, the film thickness increased by only 10% in n‐butane at 2.3 atm. Excessive increases in film thickness were shown in 1,3‐butadiene, but the decreases in film density were minor. The probability of the condensation of 1,3‐butadiene in the films is indicated. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1818–1825, 2000     

Resistive switching characteristics of polyimides derived from 2,2′‐aryl substituents tetracarboxylic dianhydrides

2,2′‐Position aryl‐substituted tetracarboxylic dianhydrides including 2,2′‐bis(biphenyl)‐4,4′,5,5′‐biphenyl tetracarboxylic dianhydride and 2,2′‐bis[4‐(naphthalen‐1‐yl)phenyl)]‐4,4′,5,5′‐biphenyl tetracarboxylic dianhydride were synthesized. A new series of aromatic polyimides (PIs) were synthesized via a two‐step procedure from 3,3′,4,4′‐biphenyl tetracarboxylic dianhydride and the newly synthesized tetracarboxylic dianhydrides monomers reacting with 2,2′‐bis[4′‐(3″,4″,5″‐trifluorophenyl)phenyl]‐4,4′‐biphenyl diamine. The resulting polymers exhibited excellent organosolubility and thermal properties associated with T_g at 264 °C and high initial thermal decomposition temperatures (T_5%) exceeding 500 °C in argon. Moreover, the fabricated sandwich structured memory devices of Al/PI‐a/ITO was determined to present a flash‐type memory behaviour, while Al/PI‐b/ITO and Al/PI‐c/ITO exhibited write‐once read‐many‐times memory capability with different threshold voltages. In addition, Al/polymer/ITO devices showed high stability under a constant stress or continuous read pulse voltage of ? 1.0 V. Copyright © 2011 Society of Chemical Industry     

Synthesis and characterization of organosoluble and transparent polyimides derived from trans‐1,2‐bis(3,4‐dicarboxyphenoxy)cyclohexane dianhydride

A novel dianhydride, trans‐1,2‐bis(3,4‐dicarboxyphenoxy)cyclohexane dianhydride (1,2‐CHDPA), was prepared through aromatic nucleophilic substitution reaction of 4‐nitrophthalonitrile with trans‐cyclohexane‐1,2‐diol followed by hydrolysis and dehydration. A series of polyimides (PIs) were synthesized from one‐step polycondensation of 1,2‐CHDPA with several aromatic diamines, such as 2,2′‐bis(trifluoromethyl)biphenyl‐4,4′‐diamine (TFDB), bis(4‐amino‐2‐trifluoromethylphenyl)ether (TFODA), 4,4′‐diaminodiphenyl ether (ODA), 1,4‐bis(4‐aminophenoxy)benzene (TPEQ), 4,4′‐(1,3‐phenylenedioxy)dianiline (TPER), 2,2′‐bis[4‐(3‐aminodiphenoxy)phenyl]sulfone (m‐BAPS), and 2,2′‐bis[4‐(4‐amino‐2‐trifluoromethylphenoxy)phenyl]sulfone (6F‐BAPS). The glass transition temperatures (T_gs) of the polymers were higher than 198°C, and the 5% weight loss temperatures (T_d5%s) were in the range of 424–445°C in nitrogen and 415–430°C in air, respectively. All the PIs were endowed with high solubility in common organic solvents and could be cast into tough and flexible films, which exhibited good mechanical properties with tensile strengths of 76–105 MPa, elongations at break of 4.7–7.6%, and tensile moduli of 1.9–2.6 GPa. In particular, the PI films showed excellent optical transparency in the visible region with the cut‐off wavelengths of 369–375 nm owing to the introduction of trans‐1,2‐cyclohexane moiety into the main chain. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42317.     

2,2-二(溴甲基)-1,3-丙二醇的合成

以季戊四醇和４０％氢溴酸溶液为原料,冰醋酸为催化剂,经取代反应、减压分离、纯化和干燥等步骤合成了具有优良性能的反应型阻燃剂２,２ 二（溴甲基） １,３ 丙二醇,以季戊四醇计,产品收率为８０．８％。实验确定了氢溴酸与季戊四醇的最佳摩尔比为２．５∶１,最佳反应时间为６～８ｈ,最佳反应温度为回流温度。先用等体积的甲苯和水混合物分离合成产物,再用热水重结晶进行纯化。经元素分析、熔点测定和红外光谱分析予以确证。     

Multiarm hyperbranched polyester‐b‐Poly(ε‐caprolactone):Plasticization effect and migration resistance for PVC

A series of multiarm structure hyperbranched polyester‐b‐poly(ε‐caprolactone) (HEPCLs) with different lengths of poly(ε‐caprolactone) (PCL) segments (s = 3, 6, 7, 8) were synthesized. Hyperbranched polyester (HE) was synthesized from glycidol and succinic anhydride and used as a macromolecular polymerization initiator for ε‐caprolactone. The HEPCLs were used as polyvinyl chloride (PVC) plasticizers and the mechanical properties, thermal properties, morphology, and migration stabilities of PVC films were explored. The plasticizing efficiency increased with the increase in PCL segments, and the plasticizing efficiency of HEPCL₈ exceeded that of dioctyl phthalate. Scanning electron microscopy and solid‐state ¹H NMR showed that the HEPCLs possess better compatibility with PVC than HE. Moreover, HEPCLs exhibited excellent migration stability even at very harsh condition, indicating that HEPCLs can be used as no‐migration PVC plasticizers in medical products, children's toys, and food packaging. J. VINYL ADDIT. TECHNOL., 26:35–42, 2020. © 2019 Society of Plastics Engineers     

The Synthesis of Energetic Compound on 4,4′‐((2,4,6‐trinitro‐1,3‐phenylene)bis(oxy)) bis(1,3‐dinitrobenzene)(ZXC‐5): Thermally Stable Explosive with Outstanding Properties

The novel, thermally stable explosive 4,4′‐((2,4,6‐trinitro‐1,3‐phenylene)bis(oxy))bis(1,3‐dinitrobenzene) (Be referred to as ZXC‐ 5 in our laboratory) has been reported. ZXC‐5 can be synthesized by a simple synthetic method (The total synthesis of ZXC‐ 5 requires only two steps and the total yield of ZXC‐ 5 is more than 89 %) and shows the superior detonation performances (detonation pressure, detonation velocity, sensitivity toward mechanical stimuli, and temperature of decomposition). The structure of ZXC‐5 was characterized by multinuclear (¹H, ¹³C) NMR and mass spectrometry. The structure in the crystalline state was confirmed by low‐temperature single‐crystal X‐ray diffraction. From the calculated standard molar enthalpy of formation and the measured densities, the detonation properties were predicted by using the EXPLO5 V6.01 thermochemical computer code. The sensitivity of ZXC‐ 5 towards impact, electrostatic discharge, and friction were also measured.