Study on short glass fiber‐reinforced poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) composites

Biobased non‐fossil polyester poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P3/4HB) containing 4.0 mol % 4‐hydroxybutyrate (4HB) was melt‐mixed with short glass fibers (SGF) via a co‐rotating twin‐screw extruder. The compositing conditions, average glass fiber length and distribution, thermal, crystallization, and mechanical properties of the P3/4HB/SGF composites were investigated. Calcium stearate, two kinds of paraffin wax and modified ethylene bis‐stearamide (TAF) were investigated as lubricants for the P3/4HB/SGF composites. It revealed that TAF is the most efficient lubricant of the P3/4HB/SGF composites. Coupling agents 2,2′‐(1,3‐phenylene)bis‐2‐oxazoline (1,3‐PBO) and pyromellitic dianhydride (PMDA) were used as end‐group crosslinkers to reduce the degradation of P3/4HB and increase the mechanical properties of the P3/4HB/SGF composites. It showed that 1,3‐PBO is the efficient coupling agent. The optimum condition of the P3/4HB/SGF composites is 1.5 phr TAF, 1.0 phr 1,3‐PBO, and 30 wt % glass fiber content. And the maximum of tensile strength, tensile modulus, and impact strength of the composites is 3.7, 6.6, 1.8 times of the neat P3/4HB polymer, respectively. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Thermal stability of poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)/modified montmorillonite bio‐nanocomposites

Poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P34HB)/modified montmorillonite (EMMT) bio‐nanocomposites were prepared via melt intercalation method. The thermal stability of the bio‐nanocomposites was investigated. The results showed that the decomposition temperature (T _5%) of P34HB/EMMT bio‐nanocomposite reached 271.4°C, 39.9°C higher than that of pure P34HB. The remarkable thermal stability enhancement was presumably originated from the uniform dispersion of EMMT in the matrix and intercalated structures of P34HB/EMMT bio‐nanocomposites, which was related to the increased compatibility of EMMT and P34HB caused by the ester group in EMMT. TGA‐FTIR analysis on the thermal degradation procedures of the bio‐nanocomposites manifested that the introduction of EMMT did not alter the degradation mechanism of P34HB. However, the intercalated structures hindered the mobility of P34HB macromolecular and slowed down the decomposing process of P34HB. POLYM. COMPOS., 38:673–681, 2017. © 2015 Society of Plastics Engineers     

Miscibility and crystallization behaviors of poly(3‐hydroxybutyrate‐co‐11%‐4‐hydroxybutyrate)/Poly(3‐hydroxybutyrate‐co‐33%‐4‐hydroxybutyrate) blends

Biopolyesters poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) with an 11 mol % 4HB content [P(3HB‐co‐11%‐4HB)] and a 33 mol % 4HB content [P(3HB‐co‐33%‐4HB)] were blended by a solvent‐casting method. The thermal properties were investigated with differential scanning calorimetry. The single glass‐transition temperature of the blends revealed that the two components were miscible when the content of P(3HB‐co‐33%‐4HB) was less than 30% or more than 70 wt %. The blends, however, were immiscible when the P(3HB‐co‐33%‐4HB) content was between 30 and 70%. The miscibility of the blends was also confirmed by scanning electron microscopy morphology observation. In the crystallite structure study, X‐ray diffraction patterns demonstrated that the crystallites of the blends were mainly from poly(3‐hydroxybutyrate) units. With the addition of P(3HB‐co‐33%‐4HB), larger crystallites with lower crystallization degrees were induced. Isothermal crystallization was used to analyze the melting crystallization kinetics. The Avrami exponent was kept around 2; this indicated that the crystallization mode was not affected by the blending. The equilibrium melting temperature decreased from 144 to 140°C for the 80/20 and 70/30 blends P(3HB‐co‐11%‐4HB)/P(3HB‐co‐33%‐4HB). This hinted that the crystallization tendency decreased with a higher P(3HB‐co‐33%‐4HB) content. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation and characterization of biodegradable poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)/silica nanocomposites

Biodegradable poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) [P(3HB‐co‐4HB)]/silica nanocomposites were prepared by melt compounding. The effects of silica on the morphology, crystallization, thermal stability, mechanical properties, and biodegradability of P(3HB‐co‐4HB) were investigated. The nanoparticles showed a fine and homogeneous dispersion in the P(3HB‐co‐4HB) matrix for silica contents below 5 wt%, whereas some aggregates were detected with further increasing silica content. The addition of silica enhanced the crystallization of P(3HB‐co‐4HB) in the nanocomposites due to the heterogeneous nucleation effect of silica. However, the crystal structure of P(3HB‐co‐4HB) was not modified in the presence of silica. The thermal stability of P(3HB‐co‐4HB) was enhanced by the incorporation of silica. Silica was an effective reinforcing agent for P(3HB‐co‐4HB), and the modulus and tensile strength of the nanocomposites increased, whereas the elongation at break decreased with increasing silica loading. The exciting aspect of this work was that the rate of enzymatic degradation of P(3HB‐co‐4HB) was enhanced significantly after nanocomposites preparation. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Facile preparation and cytocompatibility of poly(lactic acid)/poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) hybrid fibrous scaffolds

A fibrous scaffold is required to provide three‐dimensional (3D) cell growth microenvironments and appropriate synergistic cell guidance cues. In this study, porous scaffolds with different mass ratio of poly(lactic acid) to poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P(3HB‐co‐4HB)) for tissue engineering were prepared by a modified particle leaching method. The effect of the addition of P(3HB‐co‐4HB) on microstructural morphology, compression property, swelling behavior, and enzymatic degradation of hybrid scaffolds was systematically investigated. The results indicated that this method was simple but efficient to prepare highly interconnected biomimetic 3D hybrid scaffolds (PP50/50 and PP33/67) with fibrous pore walls. The cytocompatibility of hybrid scaffolds was evaluated by in vitro culture of mesenchymal stem cells. The cell‐cultured hybrid scaffolds presented a complete 3D porous structure, thus allowing cell proliferation on the surface and infiltration into the inner part of scaffolds. The obtained hybrid scaffolds with pore size ranging from 200 to 450 µm, over 90% porosity, adjustable biodegradability, and water‐uptake capability will be promising for cartilage tissue engineering applications. POLYM. ENG. SCI., 54:2902–2910, 2014. © 2014 Society of Plastics Engineers     

Study of miscibility,crystallization, mechanical properties,and thermal stability of blends of poly(3‐hydroxybutyrate) and poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)

Natural amorphous polymer poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P3HB4HB) containing 41 mol % of 4HB was blended with poly(3‐hydroxybutyrate) (PHB) with an aim to improve the properties of PHB. The influence of P3HB4HB contents on thermal and mechanical properties of the blends was evaluated with differential scanning calorimetry (DSC), Fourier transform infrared (FTIR) spectroscopy, stress–strain measurement and thermo gravimetric analyzer. Miscibility of PHB/P3HB4HB blends was mainly decided by the contents of P3HB4HB. When P3HB4HB exceeded 50 wt %, the two polymer phases separated and showed immiscibility. The addition of P3HB4HB did not alter the crystallinity of PHB, yet it diluted the PHB crystalline phase as revealed by DSC studies. DSC and FTIR results showed that the overall crystallinity of the blends decreased remarkably with increasing of P3HB4HB contents. Decreased glass transition temperature and crystallinity imparted desired flexibility for the blends. The ductility of the blends increased progressively with increasing of P3HB4HB content. Thus, the PHB mechanical properties can be modulated by changing the blend composition. P3HB4HB did not significantly improve the thermal stability of PHB, yet it is possible to melt process PHB without much molecular weights loss via blending it with suitable amounts of P3HB4HB. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Miscibility,crystallization kinetics,and mechanical properties of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)(PHBV)/poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)(P3/4HB) blends

Poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)(PHBV)/poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P3/4HB) blend films were prepared by solvent‐cast method. The nonisothermal crystallization results showed that PHBV and P3/4HB are miscible due to a single glass transition temperature (T_g), which is dependent on blend composition. The isothermal crystallization results demonstrate that the crystallization rate of PHBV becomes slower after adding amorphous P3/4HB with 19.2 mol% 4HB, which could be proved through depression of equilibrium melt point ($T_m^o$ ) from 183.7°C to 177.6°C. For pure PHBV and PHBV/P3/4HB (80/20) blend, the maximum crystallization rate appeared at 88°C and 84°C, respectively. FTIR analysis showed that PHBV/P3/4HB blend films would maintain the helical structure, similar to pure PHBV. Meanwhile, with increasing P3/4HB content, the inter‐ and intra‐interactions of PHBV and P3/4HB decrease gradually. Besides, a lower elastic modulus and a higher elongation at break were obtained, which show that the addition of P3/4HB would make the brittle PHBV to ductile materials. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Rheological,thermal, and mechanical properties of P (3HB‐co‐4HB) and P (3HB‐co‐4HB)/EVA blends

Poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) [P(3HB‐co‐4HB)] fiber and P(3HB‐co‐4HB)/EVA fiber were obtained by single screw extrusion machine. The rheology of P(3HB‐co‐4HB) and P(3HB‐co‐4HB)/EVA blends was characterized by capillary rheometer, and the chemical groups of the blends were characterized with Fourier transform infrared spectroscopy (FT‐IR). The crystallization behavior and thermal, mechanical and elastic properties of the fibers were measured by differential scanning calorimeter (DSC), thermogravimetric analyzer (TGA) and single fiber strength tester, respectively. Besides, the moisture regain and drying shrinkage rates of the fibers were tested. These results showed that P(3HB‐co‐4HB)/EVA blends have better flowability, crystallinity, and thermal stability than P(3HB‐co‐4HB) fiber. The fracture strength of the P(3HB‐co‐4HB)/EVA fiber decreases with increasing the EVA content, but the elongation at break shows the contrary tendency. The rebound resilience ratio of P(3HB‐co‐4HB)/EVA fiber reaches 100%. Both moisture regain and drying shrinkage increase first and then decrease with increasing the EVA content. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41206.     

Miscibility and crystallization behavior of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/poly(vinyl acetate) blends

The miscibility and crystallization behavior of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (P(HB‐co‐HV))/poly(vinyl acetate) (PVAc) blends have been investigated by differential scanning calorimetry (DSC) and polarized optical microscopy (POM). It was found that P(HB‐co‐HV)/PVAc blends were miscible in the melt over the whole compositions. Thus the blend exhibited a single glass transition temperature (T_g), which increased with increasing PVAc composition. The spherulitic morphologies of P(HB‐co‐HV)/PVAc blends indicated that the PVAc was predominantly segregated into P(HB‐co‐HV) interlamellar or interfibrillar regions during P(HB‐co‐HV) crystallization because of the volume‐filled spherulites. As to the crystallization kinetics study, it was found that the overall crystallization and crystal growth rates decreased with the addition of PVAc. The kinetics retardation was primarily attributed to the reduction of chain mobility and dilution of P(HB‐co‐HV) upon mixing with higher T_g PVAc. The overall crystallization rate was predominantly governed by the spherulitic growth rate and promoted by the samples treated with the quenched state because of the higher nucleation density. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 980–988, 2006     

Miscibility and crystallization kinetics of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/ poly(methyl methacrylate) blends

The miscibility and crystallization kinetics of the blends of random poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) [P(HB‐co‐HV)] copolymer and poly(methyl methacrylate) (PMMA) were investigated by differential scanning calorimetry (DSC) and polarized optical microscopy (POM). It was found that P(HB‐co‐HV)/PMMA blends were miscible in the melt. Thus the single glass‐transition temperature (T_g) of the blends within the whole composition range suggests that P(HB‐co‐HV) and PMMA were totally miscible for the miscible blends. The equilibrium melting point (T°_m) of P(HB‐co‐HV) in the P(HB‐co‐HV)/PMMA blends decreased with increasing PMMA. The T°_m depression supports the miscibility of the blends. With respect to the results of crystallization kinetics, it was found that both the spherulitic growth rate and the overall crystallization rate decreased with the addition of PMMA. The kinetics retardation was attributed to the decrease in P(HB‐co‐HV) molecular mobility and dilution of P(HB‐co‐HV) concentration resulting from the addition of PMMA, which has a higher T_g. According to secondary nucleation theory, the kinetics of spherulitic crystallization of P(HB‐co‐HV) in the blends was analyzed in the studied temperature range. The crystallizations of P(HB‐co‐HV) in P(HB‐co‐HV)/PMMA blends were assigned to n = 4, regime III growth process. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3595–3603, 2004     

The influence of 4HB content on the properties of poly(3‐hydroxylbutyrate‐co‐4‐hydroxylbutyrate) based on melt molded sheets

A series of poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)s[P(3HB‐co‐4HB)s] sheets with the 4HB contents from about 9 to 34 mol % were prepared via melt molding. Their crystallinity, crystalline structures, thermal and mechanical properties were characterized by differential scanning calorimetry, X‐ray diffraction, thermogravimetric analysis, dynamic mechanical analysis, and tensile test. It was found that the melt temperatures (T_m), glass transition temperatures (T_g), and storage modulus (E′) of all the [P(3HB‐co‐4HB)s] copolymers investigated decreased continuously with increasing the amount of the 4HB; the yield stress and breaking stress nearly decreased with the increase of the 4HB contents while the elongation at the yield and break points increased; and the thermal stability of the P(3HB‐co‐4HB)s improved with increasing 4HB contents. The results suggest that the mechanical properties and crystal lattice parameters of the melt molded sheets are somewhat different from those of the solution cast films. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Water resistance,mechanical properties,and biodegradability of poly(3‐hydroxybutyrate)/starch composites

Composites of poly(3‐hydroxybutyrate), P(3HB), and starch were prepared by solution casting technique. To improve adhesion of starch to P(3HB), stearic acid was added as a compatibilizer and glycerol as a plasticizer. The water resistance, mechanical, and biodegradable properties of the P(3HB)/starch composites were studied. Diffusion and penetration coefficients of water increased with increasing starch content in the composites. The results showed that the elastic modulus and strain at rupture of the P(3HB)/starch composites were enhanced by increasing starch content upto 10 wt % and the tensile strength increased from 21.2 to 93.9 MPa. The presence of starch content higher than 10 wt % had an adverse effect on the mechanical properties of the investigated composites. The biodegradation rate using Actinomycetes increased proportionally to the starch content in the composite and accelerated in a culture medium of pH ≈ 7.0 at 30°C. Enzymatic degradation experiments showed that lipase produced by Streptomyces albidoflavus didnot degrade P(3HB)/starch composites. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Morphology and properties of biodegradable and biosourced polylactide blends with poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)

Biodegradable polymer blends based on biosourced polymers, namely polylactide (PLA) and poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P(3HB‐co‐4HB)), were prepared by melt compounding. The effects of P(3HB‐co‐4HB) on the miscibility, phase morphology, thermal behavior, mechanical properties, and biodegradability of PLA/P(3HB‐co‐4HB) blends were investigated. The blend was an immiscible system with the P(3HB‐co‐4HB) domains evenly dispersed in the PLA matrix. However, the T_g of P(3HB‐co‐4HB) component in the blends decreased compared with neat P(3HB‐co‐4HB), which might be attributed to that the presence of the phase interface between PLA and P(3HB‐co‐4HB) resulted in enhanced chain mobility near interface. The addition of P(3HB‐co‐4HB) enhanced the cold crystallization of PLA in the blends due to the nucleation enhancement of PLA caused by the enhanced chain mobility near the phase interface between PLA and P(3HB‐co‐4HB) in the immiscible blends. With the increase in P(3HB‐co‐4HB) content, the blends showed decreased tensile strength and modulus; however, the elongation at beak was increased significantly, indicating that the inherent brittlement of PLA was improved by adding P(3HB‐co‐4HB). The interesting aspect was that the biodegradability of PLA is significantly enhanced after blends preparation. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Hydrogen bonding,miscibility, crystallization,and thermal stability in blends of biodegradable polyhydroxyalkanoates and polar small molecules of 4‐tert‐butylphenol

The hydrogen bonding, miscibility, crystallization, and thermal stability of poly(3‐hydroxybutyrate) (PHB)/4‐tert‐butylphenol (BOH) blends and poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) [P(3HB‐3HHx)]/BOH blends were investigated by Fourier transform infrared (FTIR) spectroscopy, solid‐state¹³C‐NMR, differential scanning calorimetry, wide‐angle X‐ray diffraction (WAXD), and thermogravimetric analysis. The results of FTIR spectroscopy and solid‐state¹³C‐NMR show that intermolecular hydrogen bonds existed between the two components in the blends and that the interaction was caused by the carbonyl groups in the amorphous phase of both polyesters and the hydroxyl groups of BOH. With increasing BOH content, the chain mobility of both the PHB and P(3HB‐3HHx) components was improved. After the samples were quenched, the detected single glass‐transition temperatures decreased with composition, indicating that both PHB/BOH and P(3HB‐3HHx)/BOH were miscible blends in the melt. Moreover, as BOH content increased, the melting temperatures of PHB and P(3HB‐3HHx) clearly decreased, which implied that their crystallization was suppressed by the addition of BOH. Although the crystallinity of PHB and P(3HB‐3HHx) components decreased with increasing BOH content in the blends, their crystal structures were hardly affected after they were blended with BOH, which was further proven by WAXD results. In addition, the thermal stability of PHB was improved by a smaller amount of BOH.     

Processability modifications of poly(3‐hydroxybutyrate) by plasticizing,blending, and stabilizing

Poly(3‐hydroxybutyrate) (PHB) was plasticized with dioctyl (o‐)phthalate, dioctyl sebacate, and acetyl tributyl citrate (ATBC). The thermal properties, mechanical properties, and melt flow ability were studied with differential scanning calorimetry, thermogravimetric analysis, a universal material testing machine, and a melt flow indexer. ATBC was revealed to be an efficient plasticizer, reducing the glass‐transition temperature and increasing the thermoplasticization ability of PHB. We also blended poly(3‐hydroxybutyrate‐co‐hydroxyhexanoate) (PHBHHx) and poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) [P(3/4HB)] with PHB, ATBC, and antioxidant 1010 to overcome the brittleness of PHB and improve the melt flow stability of the materials. PHBHHx did little to improve the thermal processing but increased the fluidity of PHB, and P(3/4HB) toned the toughness of PHB. The addition of antioxidant 1010 enhanced the thermal stabilization of PHB. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Mechanical properties,thermal stability,and crystallization kinetics of poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)/calcium carbonate composites

Bacterial polyester poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P3/4HB) containing 5 mol% 4HB was composited with different calcium carbonate (CaCO₃) fillers. The effect of CaCO₃ contents on thermal properties, mechanical property, and crystallization kinetics was evaluated. The thermal stability of P3/4HB was reduced by mixing with CaCO₃ particles. With increasing CaCO₃ content, the elongation at break, tensile strength, and impact strength decrease; however, elastic modulus increases. When P3/4HB with 20 mol% 4HB was added into the P3/4HB/CaCO₃ composite, the impact strength were enhanced significantly; however, the elongation at break and tensile strength were only slight to moderate improvements. However, when compared with nano‐ and light‐CaCO₃, heavy CaCO₃ had the best mechanical properties. The nonisothermal and isothermal crystallization results demonstrated that the crystallization rate of P3/4HB was reduced and the highest crystallinity was obtained for all kinds of CaCO₃ fillers at 40 phr content. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Production and characterization of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) co‐polymer by a N2‐fixing cyanobacterium,Nostoc muscorum Agardh

BACKGROUND: Poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) [P(3HB‐co‐3HV)] co‐polymer has immense potential in the field of environmental and biomedical sciences as biodegradable and biocompatible material. The present study examines a filamentous N₂‐fixing cyanobacterium, Nostoc muscorum Agardh as a potent feedstock for P(3HB‐co‐3HV) co‐polymer production and characterization of co‐polymer film for commercial applications. RESULTS: Under photoautotrophic growth conditions, N. muscorum Agardh accumulated the homopolymer of poly‐β‐hydroxybutyrate (PHB), whereas synthesis of P(3HB‐co‐3HV) co‐polymer was detected under propionate‐ and valerate‐supplemented conditions. Exogenous carbons such as acetate, fructose and glucose supplementation with propionate/valerate was found highly stimulatory for the co‐polymer accumulation; the content reached 58–60% of dry cell weight (dcw) under P‐/N‐deficiencies with 0.4% acetate + 0.4% valerate supplementation, the highest value reported so far for P(3HB‐co‐3HV) co‐polymer‐producing cyanobacterial species. The material properties of the films were studied by mechanical tests, surface analysis and differential scanning calorimetry (DSC). CONCLUSION: N. muscorum Agardh, a photoautotrophic N₂‐fixing cyanobacterium, emerged as a potent host for production of P(3HB‐co‐3HV) co‐polymer with polymer content 60% of dry cell weight. The material properties of the films were found to be comparable with that of the commercial polymer, thus advocating its potential applications in various fields. Copyright © 2012 Society of Chemical Industry     

Study on the poly(3‐hydroxybutyrate‐co−4‐hydroxybutyrate)‐based composites toughened by synthesized polyester polyurethane elastomer

In this study, polycaprolactone(PCL)‐based polyurethane (PU) elastomer containing 45 wt % hard segment component was synthesized and characterized by fourier transform infrared spectroscopy, gel permeation chromatography, and X‐ray diffraction. As a toughening agent, the as‐synthesized PU was incorporated into biodegradable poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) [P(3,4)HB] by solution casting to prepare P(3,4)HB/PU composites. The microstructure and properties of P(3,4)HB/PU composites were investigated using transmission electron microscopy, X‐ray diffraction, tensile testing, scanning electron microscopy, differential scanning calorimetry, thermogravimetric analysis, and activated sludge degradation testing. The results show that PU can disperse well in a P(3,4)HB matrix. The elongation at break of P(3,4)HB/PU composites is remarkably increased while the yield strength and elastic modulus are decreased with an increase in PU content. At the same time, it is found that the fracture characteristic of P(3,4)HB is obviously transformed from brittleness into ductility with a gradual increase in PU loading. Moreover, the thermal stability of P(3,4)HB/PU composites is significantly improved compared with that of pure P(3,4)HB. In addition, the biodegradation rate of P(3,4)HB/PU composites is evidently reduced with the increase of PU content in the activated sludge degradation testing. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42740.     

The structure and photocatalytic performances of mechanically synthesized poly(3′,4′‐ethylenedioxy‐2,2′:5′,2″‐Terthiophene)/Zno composites

Poly(3′,4′‐ethylenedioxy‐2,2′:5′,2″‐terthiophene)/ZnO(poly(TET)/ZnO) composites with the ratio of poly(TET) and nano‐ZnO from 3:1 to 1:3 were synthesized by hand grinding and ball milling methods, respectively. The photocatalytic activities of the composites were examined through the degradation processes of methylene blue (MB) solution under UV light irradiation, and the possible mechanism for the photocatalytic activity enhancement by synergetic effects between nano‐ZnO and poly(TET) was proposed. The results showed that the strong interactions between the poly(TET) and nano‐ZnO occurred in the case of ball milling method. The results also proved that the crystallinity of ZnO was not disturbed in both of methods, and the nano‐ZnO was uniformly distributed in polymer matrix in the case of ball milling method. The comparative studies showed that the addition of the nano‐ZnO could enhance the photocatalytic activities of the composites. The highest degradation efficiency (100%) at 3 h under UV light irradiation occurred in the case of poly(TET)/ZnO(1:1) synthesized by ball milling method. Furthermore, the nanocompsosite displayed higher photocatalytic activity than nano‐ZnO, which was due to the holes (h⁺) transferring from the valence band of ZnO to the polymer backbone and the adsorption of MB molecules in polymer matrix via π–π conjugation between MB and aromatic regions of the poly(TET). POLYM. COMPOS., 36:1597–1605, 2015. © 2014 Society of Plastics Engineers     

Miscibility and intermolecular hydrogen‐bonding interactions in poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate)/poly(4‐vinyl phenol) binary blends

The miscibility and hydrogen bonding interaction in the poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate)/poly(4‐vinyl phenol) [P(3HB‐co‐3HH)/PVPh] binary blends were investigated by differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR). The DSC results indicate that P(3HB‐co‐3HH) with 20 mol % 3HH unit content is fully miscible with PVPh, and FTIR studies reveal the existence of hydrogen bonding interaction between the carbonyl groups of P(3HB‐co‐3HH) and the hydroxyl groups of PVPh. The effect of blending of PVPh on the mechanical properties of P(3HB‐co‐3HH) were studied by tensile testing. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007