Al-1Mn-1Mg合金热变形过程中的动态软化行为研究

研究了Al-1Mn-1Mg合金不同变形下的流变应力曲线和微观结构特征,探讨了该铝材在热变形过程中的动态软化行为。结果表明,应变速率为0.1 s-1时,若变形温度较低,则发生了动态回复;若变形温度高于723 K,产生明显的动态再结晶;变形温度为673 K时,在低应变速率条件下,产生动态再结晶,应变速率高于0.1 s-1,软化过程具有动态回复和动态再结晶的混合特征。当应变速率高于5.0 s-1时,产生几何动态再结晶。     

Hot deformation behavior and flow stress model of F40MnV steel

Single hit compression tests were performed at 1 223-1 473 K and strain rate of 0.1-10 s-1 to study hot deformation behavior and flow stress model of F40MnV steel. The dependence of the peak stress, initial stress, saturation stress, steady state stress and peak stain on Zener-Hollomon parameter were obtained. The mathematical models of dynamic recrystallization fraction and grain size were also obtained. Based on the tested data, the flow stress model of F40MnV steel was established in dynamic recovery region and dynamic recrystallization region, respectively. The results show that the activation energy for dynamic recrystallization is 278.6 kJ/mol by regression analysis. The flow stress model of F40MnV steel is proved to approximate the tested data and suitable for numerical simulation of hot forging.     

Flow stress behavior and processing map of Al-Cu-Mg-Ag alloy during hot compression

The hot deformation behavior of Al-Cu-Mg-Ag was studied by isothermal hot compression tests in the temperature range of 573-773 K and strain rate range of 0.001-1 s^-1 on a Gleeble 1500 D thermal mechanical simulator. The results show the flow stress of Al-Cu-Mg-Ag alloy increases with strain rate and decreases after a peak value, indicating dynamic recovery and recrystallization. A hyperbolic sine relationship is found to correlate well the flow stress with the strain rate and temperature, the flow stress equation is estimated to illustrate the relation of strain rate and stress and temperature during high temperature deformation process. The processing maps exhibit two domains as optimum fields for hot deformation at different strains, including the high strain rate domain in 623-773 K and the low strain rate domain in 573-673 K.     

AZ31镁合金热变形规律的研究

利用等温压缩试验方法,研究了AZ31镁合金在应变速率为0.001~1 s-1,变形温度为473K~623K的条件下的变形行为.动态再结晶是该试验条件下晶粒细化的主要机制,通过分析显微组织的变化来研究动态再结晶的机制,同时研究孪晶对再结晶机制的影响.     

含稀土的23Cr型双相不锈钢的高温变形行为

利用Gleeble-3500热力模拟试验机在950-1200℃,应变速率为0.1-10s-1条件下进行了含稀土的23Cr型双相不锈钢的热压缩变形,获得了流变曲线,建立了热变形方程,分析了变形组织。结果表明：在流变曲线上既存在峰值应力也有稳态应力;在高温低应变速率条件下,峰值应变减小。上述变形条件下,试验钢的热变形激活能Q=436kJ/mol,表观应力指数n=3.91,热变形方程为：ε=2.41×1016[sinh（0.012σs）]3.91exp （-436000/RT）。奥氏体的动态再结晶在试验钢的动态软化机制中起主导作用且随着温度的升高和应变速率的降低越来越充分;而大应变下,铁素体的软化主要表现为较充分的动态回复。稀土元素影响了热变形时两相中Mo元素的再分配是稀土改善双相不锈钢高温塑性的重要原因之一。稀土使Mo在铁素体中浓度较低温度下降低,高温下升高;而奥氏体相中,使得Mo浓度在较低温度下升高而高温下降低。     

Determination of the dynamic recrystallization kinetics model for SCM435 steel

The flow stress behavior of SCM435 steel was studied by using a MMS-200 thermal simulation machine, under the conditions with deformation temperatures of 1023–1323 K and strain rate of 0.01–10 s^?1. The experimental results indicated that the critical strain would get smaller with the increment in temperature and the decrement in strain rate, leaving the dynamic recrystallization easier to occur. The peak stress constitutive equation of SCM435 steel under high temperatures was established by the form of hyperbolic sine, and the activation energy of deformation under high temperature was obtained by regression equation. The critical strain ? _c for dynamic recrystallization was accurately derived from the θ-σ curve containing strain hardening rate θ and flow stress σ. Then the correlation between peak stress, peak strain, critical stress, critical strain and the parameter Z was further obtained. The Avrami kinetic equation of dynamic recrystallization for SCM435 steel was developed from stress-strain curve, and the Avrami exponent m was abstracted. Observations also indicated that the Avrami constants would decrease with increments in temperature, but increase with increments in strain rate. The Avrami constant took small influence from the deforming temperature, but significant influence from strain rate, and the correlation between Avrami constant and the strain rate was obtained by regression equation.     

温度和应变速率对ZK60镁合金压缩变形行为的影响

在应变量为0.6（ε=0.6）、不同温度（523~723 K）和应变速率（0.001~10 s-1）条件下,利用Gleeble-1500D热模拟试验机,对铸态ZK60镁合金进行热压缩变形行为的研究,分析变形温度和应变速率对ZK60镁合金压缩变形行为的影响规律,即在相同应变速率条件下,随着变形温度的升高,合金的峰值应力降低。在相同温度条件下,随着应变速率的增大,合金的流变应力增大。计算其应变速率敏感指数m值为0.14和表观激活能Q值为226~254 kJ/mol。研究表明,在温度为573~673 K、应变速率为0.001~0.1 s-1时,合金发生动态再结晶。     

Al-Mg-Si合金热压缩变形的流变应力方程

为了给制定和优化热加工工艺参数提供理论依据,采用Gleeble-1500热模拟机研究了含锆Al-Mg-Si合金在变形温度为653~803 K、变形速率为0.01~10s^-1条件下的热压缩变形的流变应力行为,并通过回归法建立材料变形的流变应力数学模型.结果表明：该合金为正应变速率敏感材料,真应力-真应变曲线存在明显的稳态流变特征;流变应力随着变形速率的增加以及变形温度的降低而增加;在较低变形温度条件下,真应力〖CDF*3〗真应变曲线为动态回复曲线;在较高变形温度条件下真应力-真应变曲线为动态再结晶曲线.该合金流变应力σ可用包含Arrhenius项的Zener Hollomon参数的函数来描述,式中A、α和n的值分别为1.89×10¹⁰s^-1、0.024MPa^-1和7.46,热变形激活能Q为166.85kJ/mol.     

Constitutive Modeling and Dynamic Recrystallization Mechanisms of an Ultralow-carbon Microalloyed Steel During Hot Compression Tests

The hot deformation behavior of an ultralow-carbon microalloyed steel was investigated using an MMS-200 thermal simulation test machine in a temperature range of 1 073-1 373 K and strain rate range of 0.01-10 s~(-1).The results show that the flow stress decreases with increasing deformation temperature or decreasing strain rate.The strain-compensated constitutive model based on the Arrhenius equation for this steel was established using the true stress-strain data obtained from a hot compression test.Furthermore,a new constitutive model based on the Z-parameter was proposed for this steel.The predictive ability of two constitutive models was compared with statistical measures.The results indicate the new constitutive model based on the Z-parameter can more accurately predict the flow stress of an ultralow-carbon microalloyed steel during hot deformation.The dynamic recrystallization (DRX) nucleation mechanism at different deformation temperatures was observed and analyzed by transmission electron microscopy (TEM),and strain-induced grain boundary migration was observed at 1 373 K/0.01 s~(-1).     

82B高碳钢热变形行为研究

采用单道次热压缩实验方法,在Thermomaster-Z型热模拟试验机上模拟高碳钢高速线材热轧变形过程动态再结晶行为,测定82B高碳钢在变形温度为800～1 100℃、变形速率为0.1～50 s-1、变形程度为0～0.60条件下的真应力-应变曲线,利用曲线特征值确定高应变速率下的变形激活能,根据实验结果分析动态再结晶变形条件,建立动态再结晶状态图。     

Plastic deformation behavior of ZK60 magnesium alloy with addition of neodymium

The hot deformation simulation of a ZK60 magnesiuln alloy at different temperatures from 373 to 673 K and different strain rates of 0.1, 0.01 and 0.002 s^-1 was studied by using the Gleebe-1500 simulator. The plastic deformation behavior was measured and the deformation activation energy was calculated. The microstructures of ZK60 magnesium alloy with an addition of neodymium during the deformation process were observed by using Polyvar-MET optical microscope and Tecnai G^2 20 TEM. The results show that the working hardening, the dynamic recovery and the dynamic recrystallization occur during the plastic deformation process at different temperatures and strain rates. The dynamic recrystallization starts when the temperature is over 473 K and the DRX grain size after hot deformation is only 5-10 μm. So the refined grains improve both the tensile strength and the elongation of alloys at room temperature. Neodymium is added into the alloy and a precipitate phase Mg12Nd that impedes the movement of dislocations is formed, which benefits to increasing mechanical properties of ZK60 magnesium alloy.     

Q235钢CSP轧制时动态再结晶行为研究

利用Gleeble-1500热模拟实验机研究Q235钢连铸坯CSP轧制时在高温变形过程中的动态再结晶行为。结果表明,在高变形温度和低应变速率条件下Q235钢易发生动态再结晶;在回归相应的数学模型后,建立了Q235钢的热变形方程式。对Q235钢连铸坯热变形后的组织进行分析,发现奥氏体发生动态回复后转变的铁素体组织中也有动态再结晶晶粒。     

Mg-9Gd-3Y合金热变形行为与本构关系

为了解决Mg-9Gd-3Y合金在热塑性变形过程中的本构关系问题,对Mg-9Gd-3Y合金进行了不同变形温度（653～753K）下采用不同应变速率（0.01～10s-1）的热压缩试验,利用载荷/位移数据建立真应力/真应变曲线和本构方程.结果表明：动态再结晶在晶界处较易发生,流变曲线显示出典型的动态再结晶特征,以及应力水平与变形温度和应变速率的关系.本构方程预测出的流变应力数据与相应的试验结果较一致.     

Dynamic recrystallization behavior of 35CrMo structural steel

1　ＩＮＴＲＯＤＵＣＴＩＯＮＤｕｒｉｎｇｈｏｔｗｏｒｋｉｎｇ ,ｓｅｖｅｒａｌｍｅｔａｌｌｕｒｇｉｃａｌｐｈｅｎｏｍｅｎａｓｕｃｈａｓｗｏｒｋ ｈａｒｄｅｎｉｎｇ (ＷＨ ) ,ｄｙｎａｍｉｃｒｅｃｏｖｅｒｙ (ＤＲＶ) ,ａｎｄｄｙｎａｍｉｃｒｅ ｃｒｙｓｔａｌｌｉｚａｉｔｏｎ (ＤＲＸ )ｏｃｃｕｒｓｉｍｕｌｔａｎｅｏｕｓ ｌｙ[1 5 ] .Ｅｓｐｅｃｉａｌｌｙ ,ｔｈｅｏｃｃｕｒｒｅｎｃｅｏｆＤＲＸ ,ｃａｎｒｅｆｉｎｅｇｒａｉｎａｎｄｒｅｄｕｃｅｄｅｆｏｒｍａｔｉｏｎｒｅｓｉｓｔａｎｃｅｉｎｐｒａｃｔｉｃａｌｈｏｔ ｗ…     

Dynamic recrystallization behaviour of Nb-Ti microalloyed steels

The dynamic recrystallization （DRX） behavior of Nb-Ti microalloyed steels was investigated by isothermal single compression tests in the temperature range of 900-1 150 ℃ at constant strain rates of 0.1-5 s^-1. DRX was retarded effectively at low temperature due to the onset of dynamic precipitation of Nb and Ti carbonitrides, resulting in higher values of the peak strain. An expression was developed for the activation energy of deformation as a function of the contents of Nb and Ti in solution as well as other alloying elements. A new value of corrective factor was determined and applied to quantify the retardation produced by increase in the amount of Nb and Ti dissolved at the reheating temperature. The ratio of critical strain to peak strain decreases with increasing equivalent Nb content. In addition, the effects of Ti content and deformation conditions on DRX kinetics and steady state grain size were determined. Finally, the kinetics of dynamic precipitation was determined and effect of dynamic precipitation on the onset of DRX was clarified based on the comparison between precipitate pinning force and recrystallization driving force.     

Hot deformation behavior and constitutive relationship of Q420qE steel

Isothermal compression tests at temperatures from 1 273 to 1 423 K and strain rates from 0.1 to 10 s-1 were carried out to investigate the flow behaviors of Q420qE steel.Stress-strain data collected from the tests were employed to establish the constitutive equation,in which the influence of strain was incorporated by considering the effect of strain on material constants Q,n,α,and ln A.The results show that the flow stress curves are dependent on the strain,strain rate and deformation temperature.They disp...     

Effect of twinning on flow stress during initial stage of hot compression of twin roll cast Mg-5.51Zn-0.49Zr alloy

A Thermecmastor-Z hot deformation simulator,optical microscopy,XRD and TEM were employed to characterize the flow stress behavior and microstructure of twin roll cast ZK60 magnesium alloy during initial stage of hot compression at elevated temperature of 300 ℃ and 400 ℃ and a given strain rate of 10-2s-1.The results suggest that flow stress drop during initial stage of hot compression at 300℃,generally led by dynamic recrystallization,is attributed to twinning,correspondingly to dynamic recrystallization as...     

玄武岩纤维地聚物混凝土的高温动态力学特性

采用自主研制的高温100 mm SHPB试验装置,研究了玄武岩纤维增强地聚物混凝土(BFRGC)的瞬时高温动态力学特性.采用厚度为1.0 mm,直径为30,35,40,45,50 mm的铝片作为整形器对入射波进行整形,保证了试验过程的有效性.结果表明:不同温度下,玄武岩纤维地聚物混凝土(BFRGC)的动态抗压强度、峰值应变和能量吸收特性随应变率的提高近似线性增长;200℃时BFRGC的动态抗压强度相对于常温时大幅度提高;随着温度的升高,BFRGC的峰值应变显著提高,且均大幅度高于常温时的峰值应变值;200～600℃时BFRGC的吸能特性明显优于常温状态,而800℃时能量吸收特性明显降低.     

Hot deformation behaviors and flow stress model of GCr15 bearing steel

The hot deformation behaviors of GCr15 bearing steel were investigated by isothermal compression tests, performed on a Gleeble-3800 thermal-mechanical simulator at temperatures between 950℃ and 1150℃ and strain rates between 0.1 and 10 s^-1. The peak stress and peak strain as functions of processing parameters were obtained. The dependence of peak stress on strain rate and temperature obeys a hyperbolic sine equation with a Zener-Hollomon parameter. By regression analysis, in the temperature range of 950-1 150℃ and strain rate range of 0.1-10 s^-1, the mean activation energy and the stress exponent were determined to be 351kJ/mol and 4.728, respectively. Meanwhile, models of flow stress and dynamic recrystallization （DRX） grain size were also established. The model predictions show good agreement with experimental results.     

Hot-compression behavior of Al alloy 5182

Hot-compression of aluminum alloy 5182 was carried out on a Gleeble-1500 thermo-simulator at deformation temperatureranging from 350 °C to 500 °C and at strain rate from 0.01 s 1to 10 s 1with strain range from 0.7 to 1.9. The microstructures andmacro-textures evolution under different conditions were investigated by polarized optical microscopy and X-ray diffraction analysis,respectively. The basic trend is that the hot-compression stress increases with the decrease of temperature and increase of strain rate,which is revealed and elucidated in terms of Zener-Hollomon parameter in the hyperbolic sine equation with the hot-deformationactivation energy of 143.5 kJ/mol. An empirical constitutive equation is proposed to predict the hot-deformation behavior underdifferent conditions. As deformation temperature increases up to 400 °C, at strain rate over 1 s 1, dynamic recrystallization (DRX)occurs. Cube orientation {100} 001 is detected in the recrystallized sample after hot-compression.