Effect of Wet Surface Treated Nano-SiO2 on Mechanical Properties of Polypropylene Composite

Nano-SiO2/polypropylene composite was prepared by melt-blending process. The nano-SiO2 particles were organized by wet process surface treatment with silane coupling agent KH-570. The effect of mass fraction of nano-SiO2 particles and dosage of KH-570 on the toughening and strengthening of PP matrix were investigated based on the fractography of impact notch and the analysis of crystal structure by X-ray and dispersive structure of nano-SiO2 by TEM. Results show that the impact and flexural strength and modulus of the composite are improved obviously with low loading of nano-SiO2 (3wt%-5wt%), and the izod impact strength of PP increases twice with 4wt% nano-SiO2. The nano-SiO2 particles treated can disperse into the matrix resin, which has evident heterogeneous nucleation effects on the crystallization of PP. The optimal toughening and strengthening effects of PP matrix can be obtained when the content of nano-SiO2 and KH-570 are 4wt% and 3wt%, respectively.     

Self-Propagating High-Temperature Reduetive Synthesis of TiB2-Al2O3 Composite Powders

TiB2-Al2O3 composite powders were produced by self-propagating high-temperature synthesis（SHS） method with reductive process from B2O3-TiO2-AI system. X-ray diffraction（XRD） and scanning electron microscopy（SEM） analyses show the presence of TiB2 and Al2O3 only in the composite powders produced by SHS. The powders are uniform and free-agglomerate. Transmission electron microscopy （TEM） and high resolution electron microscopy （HREM） observation of microstructure of the composite powders indicate that the interfaces of the TiB2-Al2O3 bond well, without any interfacial reaction products. It is proposed that the good interfacial bonding of the composite powders can be resulted from the TiB2 particles crystallizing and growing on the Al2O3 particles surface with surface defects acting as nucleation centers.     

Dielectric Properties of B2O3 Doped MgTiO3-CaTiO3 System Ceramics

The dielectric ceramics with a main crystal phase of MGTiO3 and additional crystal phase of CaTiO3 were prepared by the conventional electronic ceramics technology .the strucures of MgTiO3 are ilmenitetype,and belong to hexagonal syngony.the ratio of MgTiO3 to Ca TiO3 doping on the dielectric properties of MGTiO3-CaTiO3(MCT)ceranics were inrestigated.the addition of B2O3 decreases the sintering temperatnre and results in rapid desification without obrious negative effect on the Q values of the system(Q=1/tan ).B2O3 exists as liquid phase in the sintering process,promoting the reactions as a singering agent.     

Antibacterial properties of TiO<Subscript>2</Subscript> ceramic pellets prepared using nano TiO<Subscript>2</Subscript> powder

Titanium dioxide (TiO₂) porous ceramic pellets with three dimension nano-structure were prepared using nano TiO₂ powder. The TiO₂ porous ceramic pellets were composed of TiO₂ nanoparticles with 14–16 nm in diameter and had porosity of 74.85%. The mean pore size of the TiO₂ porous ceramic pellets was 20.73 nm and the main pore size ranged from 3 to 16 nm. The mass loss of the TiO₂ ceramic pellets was less than 5% after 20 d immersion in water. The antibacterial properties of the TiO₂ pellets were studied. The sterilization rate of Colibacillus (hospital polluted water with bacterium) can reach 99% after 3 h photocatalytic process and these TiO₂ pellets are easy to be re-activated and cyclically be used. The shaping mechanism and photocatalysis sterilization mechanism of the TiO₂ pellets were discussed. Funded by the Applied Basis Research from Sichuan Province, the Research of Photo Purification to Environment with Nano TiO₂ (No. 05YJ029-010)     

Effect of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> content on residual stress and properties of CAS glass-ceramics

The structure and properties of the glass-ceramics were tested with X-ray diffraction testing instrument,correlative software,and other modern testing means.Then the effect of Al2O3 content on internal stresses in CaO-Al2O3-SiO2 glass-ceramics was studied deeply.In order to study the relationship of Al2O3 to the residual stress of CaO-Al2O3-SiO2 glass-ceramics,X-ray diffraction ＂sin2ψ＂ was used.The means utilized the x radial incidence produced from cathode radial tube,and took the space between crystals as measurement of strain.When the stresses produced,the space between crystals changed and the diffraction peak moved during Bragg diffraction.The magnitude of movement is related to the stresses.The experimental results show the residual stress is considerably high and Al2O3 can influence the mechanical properties of this material hugely.     

Structure and dielectric properties of ZnO and Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> doped BaO-TiO<Subscript>2</Subscript> system microwave ceramics

The microwave dielectric properties and microstructure of BaTi4.3ZnyO9.6＋y ＋0.02 mol% SnO2＋0.01 mol% MnCO3＋x mol% Nb2O5（x=0-0.05, y=0-0.08） system ceramics were studied as a function of the amount of ZnO and Nb2O5 doped. Addition of （y=0-0.05） ZnO and （x=0-0.025） Nb2O5 enhanced the reactivity and decreased the sintering temperature effectively. It also increased the dielectric constant ε r and quality factor Q（=1/tan 8） of the system due to the substitution of Ti^4＋ ions with incorporating Zn^2＋and Nb^5＋ ions, which was analyzed by the reaction ZnO＋Nb2O5＋ 3 TiTxTi →ZnTi＋ 2NbTi＋3TiO2. When the system doped with （y=0.05） ZnO and （x=0.025） Nb205 were sintered at 1 160 ℃ for 6 h, the εr. Qf0 value and rfwere 36.5, 42 000 GHz, and＋1.8 ppm/℃, respectively, at 5 GHz.     

Manufacture Process of 8Y2O3 Stabilized ZrO2 from Nano Powders

The manufacture process of 8 mol% Y2O3 stabilized ZrO2 ( YSZ ) from nano powders, including the forming and sintering stages, was studied. During the forming process of YSZ powders, the relative density of YSZ increases lineally with the forming press, and the sintering linear shrinkage of YSZ to the forming press compiles to the parabola trend. When the forming press exceeding 500MPa, the samples with lower shrinkage and high density were obtained. The sintering temperature of YSZ decreases greatly because of the small size and high active surface of YSZ powders. As a result, the beginning sintering temperature of YSZ made in the experiment is as low as 825℃, and the end sintering temperature is 1300-1350℃ . The relative density of YSZ ceramic by solid sintering at 1300-1350℃ is more than 97% , with little and small pores in the uniform microstructure.     

Microstructure and mechanical properties of TiB<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composites

Effects of Al2O3 and Ni as the additives on the sinterability, microstructure and mechanical properties were systematic studied. The experimental results show that only a relative density about 96.2% of hot-pressing TiB2-30%Al2O3 can be attained due to the plate-like TiB2 particle and its random orientation and excessive Al2O3 grain growth. When sintering temperature is higher than 1 700 ℃, TiB2 grain growth can be found, which obvious improves flexural strength of TiB2 matrix but decreases toughness. It seems that mechanical properties of TiB2-Al2O3 composites are mainly depended on relative density besides grain growth. otherwise, they will be determined by relative density and TiB2 matrix strength together. Anyway, Al2O3 addition can weaken the grain boundary and thus improve the toughness of the materials. A flexural strength of 529 MPa, Vickers hardness of 24.8 GPa and indentation toughness of 4.56 MPa·m1/2 can be achieved inTiB2-30vol% Al2O3.     

The influence of mo additive on the microstructure and property of Ti/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composite

The influence of Mo on the microstructure, bending strength and HV of Ti/Al₂O₃ composite was studied, and the influence mechanism was analyzed. The results indicate that after the addition of Mo, the composite organization is finer and phases distribution is better-proportioned which make the microstructure denser, the bending strength and HV of composite are also increased to a degree. But the bending strength increases first then decreases with the increasing of Mo content, so the appropriate Mo content for the Ti/Al₂O₃ composite is to be further confirmed. WANG Zhi: Born in 1962 Funded by Natural Science Foundation of China (No. 50232020) and Natural Science Foundation of Shandong Province (No. 2002F21)     

Effect of pH values on photocatalytic properties of Bi<Subscript>2</Subscript>WO<Subscript>6</Subscript> synthesized by hydrothermal method

Highly crystalline orthorhombic Bi₂WO₆ powders were hydrothermally synthesized from aqueous solutions of Na₂WO₄ · 2H₂O and Bi (NO₃)₃ · 5H₂O over a wide range of pH. The effect of pH on morphologies, sizes and properties of the Bi₂WO₆ crystals was investigated. The band gaps of the as-prepared Bi₂WO₆ were determined from the onset of the absorption edge of UV-vis diffuse reflectance spectra. The methyl orange photodegradation was employed as a probe reaction to test the photocatalytic activity of the as-prepared samples under visible light irradiation. The photocatalytic activities of methyl orange degradation under visible light irradiation are strongly dependent on the pH used in the synthesis. The highest efficiency is observed at pH=7. Funded by the PCSIRT, the National Natural Science Foundation of China (Nos. 50532030 and 50625206) and the Zhejiang Provincial Natural Science Foundation of China (No. Z4080021)     

Synthesis of Ti3SiC2/TiB2 Composite by In-situ Hot Pressing （HP） Method

Ti3SiC2/TiB2 composite was successfully obtained by hot pressing Ti/TiC/Si/B4C power mixtures.Volume fraction of TiB2 in Ti3SiC2/TiB2 composite can not exceed 10%.Incorporation of excessive TiB2 will affect the reactions process.TiC and Ti5Si3 were two important intermediate phases during the whole reactions.The microstructure characteristics of the Ti3SiC2/TiB2 composites were analyzed using scanning electron microscopy （SEM） and transmission electron microscopy （TEM）.The experimental results show that the grains of Ti3SiC2/TiB2 composite are structured in a layered form,and the formation of TiB2 particles as reinforcements with elongated or equiaxed shape distributes in Ti3SiC2 matrix.     

High-temperature oxidation behavior of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiAl matrix composite in air

The oxidation behavior of Al₂O₃/TiAl in situ composites fabricated by hot-pressing technology was investigated at 900° in static air. The results indicate that the mass gains of the composites samples decrease gradually with increasing Nb₂O₅ content and the inert Al₂O₃ dispersoids effectively increase the oxidation resistance of the composites. The higher the Al₂O₃ dispersoids content, the more pronounced the effect. The primary oxidation precesses obey approximately the linear laws, and the cyclic oxidation precesses follow the parabolic laws. The oxidized sample containing Ti₂AlN and TiAl phases in the scales exhibits excellent oxidation resistance. The oxide scale formed after exposure at 900°C for 120 h is multiple-layered, consisting mainly of an outer TiO₂ layer, an intermediate Al₂O₃ layer, and an inner TiO₂+Al₂O₃ mixed layer. From the outer layer to the inner layer, TiO₂+Al₂O₃ mixed layer presents the transit of Al-rich oxide to Ti-rich oxide mixed layer. Near the substrate, cross-section micrograph shows a relatively loose layer, and micro- and macro-pores remain on this layer, which is a transition layer and transferres from Al₂O₃+TiO₂ scale to substrate. The thickness of oxide layer is about 20 μm. It is also found that continuous protective alumina scales can not be observed on the surface of oxidation scales. Ti ions diffuse outwardly to form the outer TiO₂ layer, while oxygen ions transport inwardly to form the inner TiO₂+Al₂O₃ mixed layer. Under long-time intensive oxidation exposure, the internal Al₂O₃ scale has a good adhesiveness with the outer TiO₂ scale. No obvious spallation of the oxide scales occurs. The increased oxidation resistance by the presence of in situ Al₂O₃ particulates is attributed to the enhanced alumina-forming tendency and thin and dense scale formation. Al₂O₃ particulates enhance the potential barrier of Ti ions from M/MO interface to O/MO interface, thereby the TiO₂ growth rate decreases, which is also beneficial to improve the oxidation resistance. Moreover, the multi-structure of the TiO₂+Al₂O₃ mixed layer decreases the indiffusion of oxygen ions and also avails to improve the high temperature oxidation resistance of the as-sintered composites. Supported by the Special Program for Education Bureau of Shaanxi Province, China (Grant No. 08JK240) and Scientific Research Startup Program for Introduced Talents of Shaanxi University of Technology, China (Grant No. SLGQD0751)     

Synthesis and electrochemical properties of Cr-doped Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript> cathode materials for lithium-ion batteries

Cr-doped Li₃V₂(PO₄)₃ cathode materials Li₃V_2−x Cr _x (PO₄)₃ were prepared by a carbothermal reduction(CTR) process. The properties of the Cr-doped Li₃V₂(PO₄)₃ were investigated by X-ray diffraction (XRD), scanning electron microscopic (SEM), and electrochemical measurements. Results show that the Cr-doped Li₃V₂(PO₄)₃ has the same monoclinic structure as the undoped Li₃V₂(PO₄)₃, and the particle size of Cr-doped Li₃V₂(PO₄)₃ is smaller than that of the undoped Li₃V₂(PO₄)₃ and the smallest particle size is only about 1 μm. The Cr-doped Li₃V₂(PO₄)₃ samples were investigated on the Li extraction/insertion performances through charge/discharge, cyclic voltammogram (CV), and electrochemical impedance spectra(EIS). The optimal doping content of Cr was that x=0.04 in the Li₃V_2−x Cr _x (PO₄)₃ samples to achieve high discharge capacity and good cyclic stability. The electrode reaction reversibility was enhanced, and the charge transfer resistance was decreased through the Cr-doping. The improved electrochemical performances of the Cr-doped Li₃V₂(PO₄)₃ cathode materials are attributed to the addition of Cr³⁺ ion by stabilizing the monoclinic structure. Funded by the Guangxi Natural Science Foundation(No. 0832259) and the National Basic Research Program of China (No. 2007CB613607)     

Mechanical characteristics of SiO<Subscript>2</Subscript> electrets

1μm SiO₂ layer was thermally grown on silicon wafer. Negative and positive charging of SiO₂ layer was performed by means of corona method at room temperature. By controlling grid voltage, we have obtained uniformly charged SiO₂ with surface potential from −500 to +200 V. With certain electric field, the electrostatic force between charged SiO₂ is investigated. Experimental results indicate that attraction not only exists between charged SiO₂ with different polarity, but also exists between charged SiO₂ with the same polarity, and no repulsion has been observed. The attractive force is related to both surface potential difference of charged SiO₂ and the uniformity of the electric field. Based on the experiment, the attractive force is supposed to be caused by polarization when two charged SiO₂ wafers are close.     

Effect of La doping on microstructure and ferroelectric properties of Bi<Subscript>4</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> thin films prepared by sol-gel method

The Bi4Ti3Oi2 and Bi3.25La0.75Ti3O12 thin films were prepared on the Pt/Ti/SiO2/Si substrate using the sol-gel method. The effect of La doping on the microstructure and ferroelectric properties of Bi4Ti3O12 films were investigated. Both the Bi4Ti3O12 and Bi3.25La0.75Ti3O12 thin films exhibited typical bismuth layered perovskite structure. The 2Pr （remanent polarization） value of Bi3.25La0.75Ti3O12 thin films is 18.6 μC/cm^2, which is much larger than that of Bi4Ti3O12 thin films. And the Bi3.2eLa0.75Ti3O12 films show fatigue-free behavior, while the Bi4Ti3O12 thin films exhibit the fatigue problem. The mechanism of improvement of La doping was discussed.     

Synthesis and characterization of (PEO)<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>−(V<Subscript>0.85</Subscript>Mo<Subscript>0.15</Subscript>)<Subscript>2</Subscript>O<Subscript>5</Subscript> nanocomposite films

(PEO) _x −(V_0.85Mo_0.15)₂O₅(x=0,0.5,1.0) nanocomposite films were prepared by a modified sol-gel method. The structure of the films was analyzed by XRD, and the DC electrical conductivity. Cyclic voltammogram and optical spectral transmittance were investigated. The results show that the (V_0.85Mo_0.15)₂O₅ xerogel has a layered structure and its interlayer space increased from 1.3181 nm at x=0 to 1.7897 nm at x=1.0. The introduction of MoO₃ improved the DC electrical conductivities of the films due to the generation of V₄₊ to maintain the electrical neutrality of the oxides. PEO intercalated in the interlayer of (V_0.85Mo_0.15)₂O₅ oxides has interaction with the oxides, enhancing the amount of Li⁺ ions inserted into the interlayer of the oxides. Moreover, the intercalation of PEO into the interlayer of (V_0.85Mo_0.15)₂O₅ oxides improved the cathodic electrochromic property in near ultraviolet region and anodic electrochromic property in visible range. JIANG Cong-sheng: Born in 1963 Supported by the Science Foundation of Hubei Province (Grant No. 2001ABB083)     

Microstrueturc and Mcehanieal Propcrtics of Heat-treated GeSb2Te4 Thin Films

The effect of annealing on microstructure, adhesive and frictional properties of GeSb2Te4 films were experimentally studied. The GeSb2Te4 films were prepared by radio frequency （RF） magnetron sputtering, and annealed at 200℃ and 340℃ under vacuum circumstance, respectively. The adhesion and friction experiments were mainly conducted with a lateral force microscope （LFM） for the GeSb2Te4 thin films before and after annealing. Their morphology and phase structure were analyzed by using atomic force microscopy （AFM） and X-ray Diffraction （XRD） techniques, and the nanoindention was employed to evaluate their hardness values. Moreover, an electric force microscope （EFM） was used to measure the surface potential. It is found that the deposited GeSb2Te4 thin film undergoes an amorphous-to-fcc and fcc-to-hex structure transition; the adhesion has a weaker dependence on the surface roughness, but a certain correlation with the surface potential of GeSb2Te4 thin films. And the friction behavior of GeSb2Te4 thin films follows their adhesion behavior under a lower applied load. However, such a relation is replaced by the mechanical behavior when the load is relatively higher. Moreover, the GeSb2Te4 thin film annealed at 340℃ presents a lubricative property.     

Preparation and characterization of CeO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript>/SnO<Subscript>2</Subscript>:Sb films deposited on glass substrates by R.F. sputtering

CeO2-TiO2 films and CeO2-TiO/SnO2：Sb （6 mol%） double films were deposited on glass substrates by radio-frequency magnetron sputtering （R.F. Sputtering）, using SnO2：Sb（6 mol%） target, and CeO2- TiO2 targets with different molar ratio of CeO2 to TiO2 （CeO2：TiO2-0：1.0; 0.1：0.9; 0.2：0.8; 0.3：0.7; 0.4：0.6; 0.5：0.5; 0.6：0.4; 0.7：0.3; 0.8：0.2; 0.9：0.1; 1.0：0）. The films are characterized by UV-visible transmission and infrared reflection spectra, scanning electron microscopy （SEM）, Raman spectroscopy, X-ray photoelectron spectroscopy （XPS） and X-ray diffraction （XRD）, respectively. The obtained results show that the amorphous phases composed of CeO2-TiO2 play an important role in absorbing UV, there are Ce^3-, Ce^4- and Ti^4- on the surface of the films; the glass substrates coated with CeO2-TiO2 （Ce/Ti=0.5：0.5; 0.6：0.4）/SnO2：Sb（6 mol%） double films show high absorbing UV（〉99）, high visible light transmission （75%） and good infrared reflection （〉70%）. The sheet resistance of the films is 30-50 Ω/□. The glass substrates coated with the double functional films can be used as window glass of buildings, automobile and so on.     

Effect of SiO2 on the Preparation and Properties of Pure Carbon Reaction Bonded Silicon Carbide Ceramics

Effect of SiO₂ content and sintering process on the composition and properties of Pure Carbon Reaction Bonded Silicon Carbide (PCRBSC) ceramics prepared with C−SiO₂ green body by infiltrating silicon was presented. The infiltrating mechanism of C−SiO₂ preform was also explored. The experimental results indicate that the shaping pressure increases with the addition of SiO₂ to the preform, and the pore size of the body turned finer and distributed in a narrower range, which is beneficial to decreasing the residual silicon content in the sintered materials and to avoiding shock off, thus increasing the conversion rate of SiC. SiO₂ was deoxidized by carbon at a high temperature and the gaseous SiO and CO produced are the main reason to the crack of the body at an elevated temperature. If the green body is deposited at 1800°C in vacuum before infiltration crack will not be produced in the preform and fully dense RBSC can be obtained. The ultimate material has the following properties: a density of 3.05–3.12 g/cm³, a strength of 580±32MPa and a hardness of (HRA)91–92.3. WU Qi-de: Born in 1949 This work was financially supported by the Key Research Project of the China (No. 96-A10-01-07) and the Key Research Project of the Wuhan (20001001003)     

Synthesis and characterization of a new Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> pillared triple-layered perovskite KSr<Subscript>2</Subscript>Nb<Subscript>3</Subscript>O<Subscript>10</Subscript>

A n-Hexyl NH₃Sr₂Nb₃O₁₀ is obtained by the stepwise ion-exchange reaction, then is dispersed in aqueous solution of trinuclear acetato-hydroxo iron (III) nitrate, [Fe₃(OCOCH₃)₇OH·2H₂O]NO₃, and the interlayer potassium cations of the perovskite niobate are exchanged with the partially hydrolyzed trinuclear acetato complex ions. On heating, the exchanged complex ions are converted into iron oxide pillars which keep the perovskite sheets apart. The product is characterized by XRD, SEM, EDAX and surface area measurement respectively. Zhang Hui: Born in 1970 Funded by the National Natural Science Foundation of China (No. 50002007), Major Program of Ministry of Education (No. 0201) and Open Foundation of State Key Lab of Advanced Tech. for Materials Synthesis and Processing.