一种基于正方环形谐振器的新型宽带带通滤波器

本文设计了一种紧凑型、宽通带、宽阻带的微带带通滤波器。该滤波器的设计是基于带有两个开路调节支节的正方谐振环。基于紧凑性的考虑,改变了传统方环谐振滤波器的馈电点和开路调节支节的位置,以便对谐振环进行折叠处理。这种改变并不影响谐振环的奇偶模特性。在输入和输出端口,通过两个叉指耦合结构对滤波器进行馈电,这种馈电方式增加了滤波器阻带的带宽和抑制度。滤波器的中心频率为4GHz,相对带宽为45％,通带内的回波损耗小于-12dB,群时延小于0．8ns,1-2．9GHz阻带抑制度大于12dB,5．3～7GHz阻带抑制度大于18dB。     

变带宽宽带数字下变频器的设计及其FPGA实现

针对宽带数字接收系统要求处理带宽可变和高度抑制干扰的特点,从传统的基于多相结构的宽带DDC出发,引入窄带DDC中整形滤波的概念,设计了带宽可变、阻带抑制高的变带宽宽带DDC,且在FPGA上实现并验证了其设计的有效性。     

基于ADS的平行耦合线带通滤波器的优化设计

从归一化低通滤波器出发,阐述了平行耦合线带通滤波器的工作原理和设计过程。给出了一个中心频率在C波段的带通滤波器设计实例。根据给定的滤波器技术指标,确定滤波器类型、结构和最佳级数。按照设计要求利用射频和微波设计软件ADS(先进设计系统)对带外抑制和插入损耗进行优化设计,从而达到要求的插损、带内波纹和理想的带外抑制特性。给出了优化的结果仿真图,结果表明优化结果与设计要求一致。     

Compact lowpass filter using spiral compact microstrip resonant cells

A novel lowpass filter using spiral compact microstrip resonant cells (SCMRCs) for size reduction is presented. Four SCMRC resonators as open stub lines are connected at both sides of an SCMRC resonator so that the port impedance at the lowpass band is matched to 50 /spl Omega/. The proposed lowpass filter has compact circuit size and wide stop-band. A demonstration lowpass filter is designed, fabricated and measured. It shows low insertion loss, flat response in the lowpass band and wide stop-band.     

基于DGS和SIR单元的超宽阻带低通滤波器设计

为了解决传统的微带线低通滤波器尺寸偏大,阻带较窄的问题,采用阶梯阻抗谐振(SIR)单元加载哑铃型缺陷地结构(DGS)单元设计了一个五阶微带低通滤波器,并通过在主传输线两侧添加并联开路枝节,以补偿DGS微带线的特性阻抗。测试结果表明:该滤波器结构尺寸21.6mm×8mm,3dB截止频率4GHz,通带内平均驻波比小于1.5,阻带范围5GHz～35GHz。实现了滤波器结构尺寸的减小和超宽阻带。     

Parallel-Coupled Coplanar-Waveguide Bandpass Filter With Multiple Transmission Zeros

A compact parallel-coupled coplanar-waveguide bandpass filter with good selectivity and stopband response is proposed. By using the quarter-wavelength resonators in implementation, the filter size can be reduced and no spurious passband is observed at twice the center frequency (2f₀). In addition, by suitably introducing the capacitive and inductive cross-coupling effects, four transmission zeros around the passband edges may be created for improving the filter selectivity. For design purpose, the equivalent-circuit models are also established. In this study, the compact fourth-order filter with multiple transmission zeros for improving the selectivity is implemented, and its stopband is extended up to 3.43f₀ with a rejection better than -30dB     

345 GHz Band-Pass Filter Using Ultra-Precision Machining Technology

This paper presents a terahertz (THz) band-pass filter using ultra-precision machining technology based on Chebyshev filter prototype. This iris inductive window coupled waveguide filter was designed by using 8 resonant cavities with a center frequency of 345 GHz and a 7% bandwidth. The final design fulfills the desired specifications and presents the minimum insertion loss of 1.55 dB and the return loss of less than 15 dB at 345 GHz. The stop-band rejection is 50 dB off the center frequency about 30 GHz, which means it has a good performance of high stop-band suppression. Compared with the recent development of THz filters, this filter possesses the characteristic of simple structure and is easy to machining.     

Design of microstrip bandpass filters with multiorder spurious-mode suppression

This paper proposes a bandpass filter design method for suppressing spurious responses in the stopband by choosing the constitutive resonators with the same fundamental frequency, but staggered higher order resonant frequencies. The design concept is demonstrated by a four-pole parallel-coupled Chebyshev bandpass filter and a compact four-pole cross-coupled elliptic-type bandpass filter. Each filter is composed of four different stepped-impedance resonators (SIRs) for which a general design guideline has been provided in order to have the same fundamental frequency and different spurious frequencies by proper adjusting the impedance and length ratios of the SIR. Being based on knowledge of the coupling coefficients and following the traditional design procedure, the resultant filter structures are simple and easy to synthesize. The measured results are in good agreement with the simulated predictions, showing that better than -30-dB rejection levels in the stopband up to 5.4f/sub 0/ and 8.2f/sub 0/ are achieved by the Chebyshev and quasi-elliptic filters, respectively.     

Wide-Stopband Microstrip Bandpass Filters Using Quarter-Wavelength Stepped-Impedance Resonators and Bandstop Embedded Resonators

Novel compact microstrip bandpass filters (BPFs) with extended stopband are proposed using both quarter-wavelength (lambda/4) stepped-impedance resonators and bandstop embedded resonators. First, by properly designing the impedance and length ratios of the stepped-impedance resonators, the developed filter may be made compact and its spurious harmonics may be pushed to the higher frequency region. Next, by suitably designing the bandstop structure so as to suppress the lower spurious harmonics of stepped-impedance resonators and then embedding the bandstop structure into the lambda/4 resonators, one may realize the BPFs with wideband spurious suppression. In particular, by connecting the bandstop embedded resonators to the input/output ports, a compact fourth-order BPF of dimension 0.089 lambdag times 0.27 lambdag is implemented and its stopband is extended up to 8.25 f ₀ with an adequate rejection of greater than 32.49 dB, where f ₀ is the passband center frequency and lambdag is the microstrip guided wavelength at f ₀.     

具有良好选择性及带外抑制的小型低通滤波器

本文提出了一种具有良好选择性以及宽带带外抑制的小型低通滤波器结构。滤波器的每一级由一段微带线和交指电容构成。基于对每一级结构的分析,我们可以确定通带的范围。为了进一步提高带外的抑制性,对单级滤波器进行了周期性的级联。通过产生多个带外衰减极点来实现带外的宽带抑制。此滤波器3dB 截止频率3.67GHz,带内插损-0.9dB,带内回波损耗低于-13dB。通带到阻带的选择度为160dB/GHz。带外抑制从3.8GHz 到13.1GHz 低于-20dB。     

Design of low-pass filter with 3-interations Koch fractal Pi-shaped DGS

A novel asymmetrical Pi-shaped defected ground structure (DGS) with 3-interations Koch fractal curves is proposed to design a microstrip low-pass filter (LPF) with ultra-wide stop-band (SB). The proposed LPFs with a single resonator and two cascaded resonators are both designed, simulated, manufactured and measured. Simulation and experiment results demonstrate that the designed LPF has a very sharp transition band (TB) and an ultra-wide SB performance compared with the existed similar symmetrical and asymmetrical DGS. The proposed LPF with two cascaded resonators is with a compact size of 36.8 mm×24.0 mm, a very low insertion loss of less than 0.7 dB under 1.9 GHz, and a wide SB from 2.2 GHz to 8 GHz with rejection of larger than 30 dB.     

Wide-stopband microstrip bandpass filters using dissimilar quarter-wavelength stepped-impedance resonators

Wide-stopband and compact microstrip bandpass filters (BPFs) are proposed using various dissimilar quarter-wavelength (/spl lambda//4) stepped-impedance resonators (SIRs) for multiple spurious suppression. The use of /spl lambda//4 SIRs is essential in widening the filter stopband and reducing the circuit size. By properly arranging the individual /spl lambda//4 SIR, which has the same fundamental resonance frequency f/sub 0/, but has different spurious (harmonic) resonance frequencies, and also carefully misaligning the maximum current density nodes, several higher order spurious resonances may be suppressed so that a BPF with wide stopband may be realized. In this study, the basic concept of multiple spurious suppression is demonstrated by thoroughly investigating the spurious characteristics of the fourth-order interdigital BPFs, which consist of two different types of /spl lambda//4 SIRs. To widen the rejection bandwidth, the fourth-order coupled-resonator BPFs based on three and four different types of /spl lambda//4 SIRs are implemented and carefully examined. Specifically, a very wide-stopband microstrip BPF composed of four dissimilar /spl lambda//4 SIRs is realized and its stopband is extended even up to 11.4f/sub 0/ with a rejection level better than 27.5 dB.     

利用ADS仿真SAW滤波器

通过某型号镜像阻抗连接结构低损耗SAW滤波器的设计过程,说明了在ADS软件中如何建立并调用各种模型来设计SAW滤波器,尤其是调用3D电磁场仿真软件计算出的封装性能,可以适应日益增高的器件工作频率和日益缩小的封装尺寸对仿真手段的要求.表面贴装器件实测结果与理论仿真基本吻合,满足了通带平滑低损耗高阻带抑制的要求,且过渡带陡峭.     

Miniature CPW Parallel-Coupled Bandpass Filter Based on Inductive Loaded Coupled-Lines and Lumped-Element J-Inverters

This study presents a compact coplanar-waveguide (CPW) parallel-coupled bandpass filter (BPF) with good selectivity and stopband rejection. The inductive terminations are introduced to the conventional anti-parallel coupled-lines, and lumped-element J-inverters are employed, to achieve both size reduction and spurious suppression. Additionally, the inductive cross-coupling effect is introduced to obtain two transmission zeros to enhance the selectivity. Suitable equivalent-circuit model is also established as effective design tool. Specifically, this work demonstrates a compact cross-coupled fourth-order BPF in grounded-CPW configuration. Compared to the conventional filters, the proposed filters exhibit over 65% size reduction, improved selectivity, and wider stopbands up to four times the center frequency     

宽阻带平面低通滤波器的设计

低通滤波器是通信系统中关键的器件之一,常作为选频器件用来抑制干扰信号和谐波信号,因此低通滤波器阻带带宽成为关键指标.常见的平面低通滤波器采用短截线(分支线)或高低阻抗线结构,这些结构的低通滤波器阻带不够宽,一般在截止频率的2倍频或3倍频处出现寄生通带.本文使用等效的T形节替代低通滤波器中的串联传输线的方式实现了带阻滤波器嵌入到低通滤波器内部,既对低通滤波器的阻带上任意频段出现的寄生通带进行了抑制,又不影响低通滤波器的通带内性能,并给出等效T形节的综合设计公式.此结构综合设计方法严谨简单、易于平面电路实现,制作出来改进的低通滤波器对3倍频寄生通带进行抑制,扩宽了阻带带宽到4个倍频程以上,测试结果:通带带宽0~3GHz,通带插入损耗小于0.5dB,带外抑制3.6~12GHz大于60dB.     

具有片上频率自动调谐功能的4MHz Gm-C滤波器

本文实现了一个应用于全集成L带DAB接收机的5阶Gm-C椭圆低通滤波器,该滤波器上集成了基于锁相环的片上频率自动调谐电路,使得该滤波器的截止频率可以准确控制在4MHz.该滤波器已经采用0.35μm CMOS工艺实现.测试结果表明,该滤波器的频率精度可以控制在1%以内,动态范围约为54dB,阻带抑制率大于40dB.该滤波器采用3.3V电源,消耗的电流约为13mA.     

SIR结构ACPW滤波器研究

文章提出将SIR谐振器结构应用于非对称共面波导传输线中,设计了一种新型SIR结构非对称共面波导带阻滤波器。通过四个SIR谐振单元在非对称共面波导传输线中级联,有效地改善了滤波器的插损和带宽。结果显示,本滤波器中心频率为1．8GHz,最小插损为0．4dB,相对带宽为33．3％,最大带外抑制为-60dB。具有小体积、低插损、高抑制、宽阻带、易于加工等优点。     

Finline and Metal Insert Filters with Improved Passband Separation and Increased Stopband Attenuation

A new class of optimized finline and metal insert filters is introduced. In these filters, the ladder-type insert is located in a waveguide section which is either wider or narrower than the embedding standard waveguide. A step junction at each end forms the transition to the standard waveguide and is included in the analysis. Both filter types provide a better suppression of spurious passbands and have significantly improved stop-band attenuation. Filters with enlarged sections are useful for design at the lower end of the waveguide band, whereas the narrower version is appropriate for bandend design.     

基于D-CRLH传输线的带阻滤波器

提出了一种新型对偶复合左右手传输线(Dual Composite Right/Left-handed Transmission Line,D-CRLHTL)结构,该结构单元由T型缺陷地(T-shaped defected ground structure,T-DGS)结构以及矩形贴片短截线组成,基于对传输线单元结构传输特性的全波仿真分析,设计了一款带阻滤波器。由于利用了基于T-DGS的D-CRLH传输线,该带阻滤波器具有较小的尺寸和更加陡峭的边沿特性。实验结果和仿真设计结果吻合较好:阻带中心频率为4.15GHz,插入损耗为30dB,3dB带宽为1.9GHz,20dB带宽为1.55GHz。     

A novel microstrip dual-mode bandpass filter with harmonic suppression

A novel dual-mode microstrip bandpass filter (BPF) with harmonic suppression is presented in this letter. The filter is composed of a perturbed square-ring resonator and two end-open L-shaped microstrip lines for the input and output of the resonator. The harmonic suppression of the BPF may be realized by choosing a proper length for the L-shaped microstrip line. The BPF has been investigated numerically and experimentally. Measured results show that the stop-band of the filter is increased up to near the third-order harmonic of the square-ring resonator due to harmonic suppression, and the rejection level is kept below -27dB.