钛合金表面GO/HA/MAO复合膜层的制备及其性能

为了改善钛合金种植体在体液中的腐蚀及摩擦腐蚀行为,延长其在人体环境中的服役时间,在微弧氧化 (MAO)膜层上采用溶胶凝胶(Sol-gel)法于羟基磷灰石(HA)和氧化石墨烯(GO)的混合溶胶中浸渍提拉成膜,从而在 Ti6Al4V 合金表面成功地制备了 GO/ HA/ MAO 复合膜层。 结果表明,MAO 膜层表面的微孔及微球被 GO/ HA 薄膜有效的覆盖且较为致密;膜层的物相组成主要为金红石相及锐钛矿相的 TiO₂、HA、SiO₂ 和GO;根据电化学腐蚀和摩擦腐蚀结果分析知,GO/ HA/ MAO 复合膜层在模拟体液(SBF)中的耐蚀性及耐摩擦腐蚀性相比于 MAO 膜层和 Ti6Al4V 基体均得到了显著提高。     

Durability of Titanium/Dicalcium Silicate Composite Coatings in Simulated Body Fluid

Titanium/dicalcium silicate composite coatings with different ratios (weight ratios as Ca₂SiO₄: Ti = 3:7, 5:5, 7:3) were prepared by plasma spraying. Effects of titanium addition on coating properties, such as bonding strength, flexural modulus, and dissolution in simulated physiological environment, were studied. Results showed that the bonding strength between coating and Ti-6Al-4V substrate increased with increase of titanium content in the composite coatings. It was explained by the narrowed dissimilarity of thermal expansion coefficients between the coatings and substrates. Degradation of mechanical properties after immersion in simulated body fluid was also studied. The dissolution of dicalcium silicate in the composite coatings resulted in the decrease of flexural strength and flexural modulus of the coatings in the simulated physiological environment. The higher titanium content in the composite coatings, the stabler are the composite coatings in the physiological environment.     

Synthesis and Characterization of Hydroxyapatite/TiO<Subscript>2</Subscript> Coatings on the β-Type Titanium Alloys with Different Sintering Parameters using Sol-Gel Method

In this study, hydroxyapatite (HA) based composite films were successfully syntheses on the β-type Ti29Nb13Ta4.6Zr (TNTZ). The solutionized TNTZ substrates coated with HA and HA/Titania (TiO₂) bioactive composite coatings by sol-gel method under various sintering parameters related to sintering temperatures and heating ramp rates. Microstructural observations of the coatings revealed that apatite was formed on the substrates. The hardness values of the coatings increase with increasing both the sintering temperature and the TiO₂ concentration in the coatings layer. However, it was found that the heating ramp rate of the sintering was not affecting the hardness values so much. Also, the hardness values of the HA/TiO₂ composite coatings at all sintering temperatures were higher than only HA coated TNTZ samples due to the existence TiO₂ phases in the HA matrix. Results indicating that the doping of HA with TiO₂, improve the physical consistency between the coating layer and the substrates and provide a better inter-particle bonding due to the existence TiO₂ phases in the HA.     

钛基材上电化学沉积羟基磷灰石

通过电沉积法在经过阳极氧化的钛基材表面沉积磷酸钙盐涂层,再经碱热处理使磷酸钙涂层转变为羟基磷灰石涂层。扫描电镜(SEM)观察了阳极氧化后生成的TiO2纳米管的微观结构,以及生成的羟基磷灰石的形貌。X射线衍射仪(XRD)分析了涂层的相组成,同时测定了涂层与基体的结合强度。试验结果表明:电沉积涂层CaHPO4·2H2O经碱处理后转变为羟基磷灰石;电沉积添加双氧水与钛基材经过阳极氧化后使得涂层与基体结合强度有所提高。模拟体液浸泡试验表明涂层具有良好的生物活性。     

Preparation and characterization of hydroxyapatite/titania composite coating on NiTi alloy by electrochemical deposition

NiTi alloy is used as biomaterial due to its unique properties, but the high content of Ni (about 50 at.%) in biomedical NiTi is of concern. Hydroxyapatite/titania composite coating was directly electrodeposited on the surface of NiTi alloy. The coated samples were characterized using X-ray diffraction, scanning electron microscopy, infrared spectroscopy, bonding strength test, polarization and electrochemical impedance spectroscopy (EIS). Results showed that addition of TiO₂ to the electrolyte changed the morphology of hydroxyapatite from thin flake-flower-like crystals to needle-flower-like crystals, and the coating was much denser. Besides, hydroxyapatite crystal grains in the coating were preferentially arranged in the [001] direction, which was perpendicular to the surface of NiTi alloy. The addition of TiO₂ improved the bonding strength between the coating and the substrate. Corrosion resistance of NiTi in the simulated body fluid at 37 °C was significantly improved by more than 50 times by electrodeposition of the hydroxyapatite/titania composite coating.     

Influence of deposition temperature on mechanical properties of plasma-sprayed hydroxyapatite coating on titanium alloy with ZrO<Subscript>2</Subscript> intermediate layer

Hydroxyapatite coatings were plasma sprayed on the Ti6A14V substrate with and without an intermediate ZrO₂ layer; meanwhile the temperatures of substrates were varied at 90, 140, and 200 °C. The coatings were subjected to the standard adhesion test per ASTM C633-79. The purpose of the investigation was to study the effects of those processing variables on the bonding strength and failure behavior of the system. It is found that the bonding strengths of HA/ZrO₂ and HA coatings generally decrease with increasing substrate temperature, except for the HA/ZrO₂ coating deposited at 200 °C. The rationale of the results is attributed to the residual stress reported in the literature. Introducing ZrO₂ bond coat is found to significantly promote the bonding strength of HA coating. The possible strengthening mechanism is the rougher surface of ZrO₂ bond coat and the higher toughness of ZrO₂, which provide the mechanical strengthening effects. The slightly denser HA in 200 °C deposited HA coating cannot explain the high bonding strength of the HA/ZrO₂ coating, nor the mechanical strengthening effect of ZrO₂ intermediate layer should apply. It is believed that a stronger diffusion bonding is formed at the interface of HA and ZrO₂, which increases the bonding between them chemically. The bonding strengths of HA/ZrO₂ and HA coatings are correlated with the area fraction of adhesive failure of the coatings. The correlation explains the findings in this study.     

Surface characterization of plasma sprayed pure and reinforced hydroxyapatite coating on Ti6Al4V alloy

Hydroxyapatite coatings suffer from poor mechanical properties like fretting fatigue, toughness and abrasive wear resistance. These properties can be enhanced by incorporation of secondary ceramic and metallic reinforcements in HA. An attempt has been made to deposit HA and HA reinforced with 10 wt.% (80Al₂O₃-20TiO₂) by plasma spray process on Ti6Al4V substrate. These coatings have been characterized using SEM/EDAX, XRD and FTIR spectroscopy. Corrosion studies have been done in SBF solution. Bio compatibility study is not included in this work. Reinforcement has enhanced the tensile strength. There is marginal improvement in microhardness and surface roughness with reinforcement. Both pure and reinforced coatings show superior resistance against corrosion in simulated body fluid.     

Structure of calcium titanate/titania bioceramic composite coatings on titanium alloy and apatite deposition on their surfaces in a simulated body fluid

In this study, TiO₂-based coatings containing Ca and P ions were prepared on titanium alloy surfaces by microarc oxidation (MAO). After soaking in aqueous NaOH solution and subsequent heat treatment at 700 and 800 °C, calcium titanate/titania bioceramic composite (CTBC) coatings were obtained. The results show that the outer layers (0–1.5 μm) of the CTBC coatings are mainly composed of Ca, Ti, O and Na constituents with a uniform distributions with increasing the depth near the surfaces. The surface phase compositions of the CTBC coating formed at 700 °C are anatase, rutile and CaTi₂₁O₃₈ phases, as well as a few CaTiO₃, while those of the CTBC coating formed at 800 °C are anatase, rutile and CaTiO₃. When incubated in a simulated body fluid (SBF), apatite was deposited on the CTBC coatings probably via formation of hydroxyl functionalized surface complexes on the CTBC coating surfaces by ionic exchanges between (Ca²⁺, Na⁺) ions of the CTBC coatings and H₃O⁺ ions in the SBF. The CTBC coating formed at 800 °C seems to facilitate the deposition of Ca and P probably due to the good crystallographic match between perovskite CaTiO₃ and HA on specific crystal planes.     

PLASMA SPRAYED Ti AND HA COATINGS： A COMPARATIVE STUDY BETWEEN APS AND VPS

Titanium (Ti) and hydroxyapatite (HA) coatings have been prepared via air (APS) and vacuum plasma spraying (VPS), and then their composition, structure, bonding strength and bioactivity were examined. The results obtained reveal that in APS process many of Ti were oxidized, but in VPS the oxidization was avoided. VPS Ti coating possesses better bonding condition than APS Ti coating. As for HA coating, higher crystallinity has been obtained while the coating was deposited by VPS as compared with APS. The simulated body fluid (SBF) tests show that both of APS and VPS HA coatings possess good bioactivity. As compared with APS, VPS is recommended as a better method to deposit Ti and HA coatings that can be applied as hard tissue replacement implants.     

Preparation and cell-materials interactions of plasma sprayed strontium-containing hydroxyapatite coating

The use of strontium-containing hydroxyapatite (Sr-HA) as a biomaterial has been reported recently. In vitro and in vivo studies have shown that Sr-HA promotes osteoblast response and stimulates new bone formation. In order to extend its usage to major load-bearing applications, such as artificial hip replacement, it has been proposed that the material could be used in the form of a coating on implant surfaces. This paper reports a preliminary study of biocompatibility of plasma sprayed Sr-HA coatings on a metallic substrate. Coatings of Sr-HA containing 10 mol% Sr²⁺ was produced on titanium alloy substrates. The coating exhibited good bonding with the substrate. The bioactivity of Sr-HA coating was evaluated in vitro by immersion in simulated body fluid (SBF). After immersion in SBF, Sr-HA coating exhibited great ability to induce apatite precipitation on its surface. The possible effects of cell-materials interactions of Sr-HA coating were examined by culturing osteoprecursor cells (OPC1) on coating surfaces. The effect of Sr-HA was also compared to a hydroxyapatite (HA) coating, which is widely used in orthopedics and dentistry. The results indicated that Sr-HA coating had good biocompatibility with human osteoblasts. OPC1 cells survived and proliferated well on the surface of coating. Sr-HA coating promoted OPC1 cells attachment, and more local contacts were produced on the surface. The presence of Sr stimulated OPC1 cell differentiation and ALP expression. No deleterious effect on ECM formation and mineralization was found with Sr-HA coating. The results indicated that Sr-HA coating had good mechanical properties and bioactivity in vitro.     

Characterization, Corrosion Resistance, and Cell Response of High-Velocity Flame-Sprayed HA and HA/TiO2 Coatings on 316L SS

The main aim of this study is to evaluate corrosion and biocompatibility behavior of thermal spray hydroxyapatite (HA) and hydroxyapatite/titania bond (HA/TiO₂)-coated 316L stainless steel (316L SS). In HA/TiO₂ coatings, TiO₂ was used as a bond coat between HA top coat and 316L SS substrate. The coatings were characterized by x-ray diffraction and scanning electron microscopy/energy dispersive spectroscopy, and corrosion resistance determined for the uncoated substrate and the two coatings. The biological behavior was investigated by the cell culture studies using osteosarcoma cell line KHOS-NP (R-970-5). The corrosion resistance of the steel was found to increase after the deposition of the HA and HA/TiO₂ bond coatings. Both HA, as well as, HA/TiO₂ coatings exhibit excellent bond strength of 49 and 47?MPa, respectively. The cell culture studies showed that HA-coated 316L SS specimens appeared more biocompatible than the uncoated and HA/TiO₂-coated 316L SS specimens.     

Effect of Spray Distance on Microstructure and Tribological Performance of Suspension Plasma-Sprayed Hydroxyapatite–Titania Composite Coatings

Hydroxyapatite (HA)–titania (TiO₂) composite coatings prepared on Ti6Al4V alloy surface can combine the excellent mechanical property of the alloy substrate and the good biocompatibility of the coating material. In this paper, HA–TiO₂ composite coatings were deposited on Ti6Al4V substrates using suspension plasma spray (SPS). X-ray diffraction, scanning electron microscopy, Fourier infrared absorption spectrometry and friction tests were used to analyze the microstructure and tribological properties of the obtained coatings. The results showed that the spray distance had an important influence on coating microstructure and tribological performance. The amount of decomposition phases decreased as the spray distance increased. The increase in spray distance from 80 to 110 mm improved the crystalline HA content and decreased the wear performance of the SPS coatings. In addition, the spray distance had a big effect on the coating morphology due to different substrate temperature resulting from different spray distance. Furthermore, a significant presence of OH^? and CO₃ ^2? was observed, which was favorable for the biomedical applications.     

Biocompatible nanostructured high-velocity oxyfuel sprayed titania coating: Deposition, characterization, and mechanical properties

Nanostructured titania (TiO₂) coatings were produced by high-velocity oxyfuel (HVOF) spraying. They were engineered as a possible candidate to replace hydroxyapatite (HA) coatings produced by thermal spray on implants. The HVOF sprayed nanostructured titania coatings exhibited mechanical properties, such as hardness and bond strength, much superior to those of HA thermal spray coatings. In addition to these characteristics, the surface of the nanostructured coatings exhibited regions with nanotextured features originating from the semimolten nanostructured feedstock particles. It is hypothesized that these regions may enhance osteoblast adhesion on the coating by creating a better interaction with adhesion proteins, such as fibronectin, which exhibit dimensions in the order of nanometers. Preliminary osteoblast cell culture demonstrated that this type of HVOF sprayed nanostructured titania coating supported osteoblast cell growth and did not negatively affect cell viability. This article was originally published inBuilding on 100 Years of Success, Proceedings of the 2006 International Thermal Spray Conference (Seattle, WA), May 15–18, 2006, B.R. Marple, M.M. Hyland, Y.-Ch. Lau, R.S. Lima, and J. Voyer, Ed., ASM International, Materials Park, OH, 2006.     

原位生成 WC-B4C 增强镍基激光熔覆层及其性能研究

目的通过激光熔覆技术,在Q235钢表面原位生成WC-B4C增强镍基熔覆层。方法以WO3,B2O3,C和Ni60混合粉末为预涂原料,采用激光熔覆技术原位生成WC-B4C增强镍基熔覆层,对熔覆层的显微组织和物相构成进行分析,研究其摩擦磨损性能。结果采用合适的工艺参数,通过原位生成WC-B4C形成的增强镍基涂层形貌良好,与基材呈现较好的冶金结合。熔覆层平均硬度1200HV0.3,摩擦磨损失重仅为纯Ni60熔覆层的1/3。结论熔覆层硬度较高,耐磨性很好。大量原位生成的WC-B4C增强相及其均匀分布是熔覆层硬度和耐磨性提高的原因。     

Fabrication and Characterization of Suspension Plasma-Sprayed Fluoridated Hydroxyapatite Coatings for Biomedical Applications

Fluoridated hydroxyapatite (FHA) coatings were prepared on a Ti substrate using a suspension plasma spraying technique. The crystalline phases and chemical compositions of the coatings were characterized using x-ray diffraction, Fourier transform infrared spectroscopy, and x-ray photoelectron spectroscopy. The analysis confirmed that the coating consisted of an FHA phase. The corrosion behavior in simulated body fluid was studied using potentiodynamic polarization tests, and the results indicated that the FHA coating greatly enhanced the corrosion resistance of the Ti substrate. The chemical stability of the FHA coatings was assessed by evaluating the release of Ca²⁺ ions. The results indicated that the substitution of fluorine into the hydroxyapatite (HA) structure had a positive effect on the dissolution resistance of the HA. The antibacterial activity was investigated using a surface-plating method; the results revealed that the antibacterial activity of the FHA coating was greater than that of the pure HA coatings. During cell culture tests, the FHA coating did not exhibit cytotoxicity toward the osteoblast cell line, and the cell proliferation was comparable with that of the HA coatings. The antibacterial activity and cell culture results suggested that the plasma-sprayed FHA coating possesses good antibacterial qualities, but is biocompatible with osteoblasts. The promising features of the FHA coating render it suitable for orthopedic and dental applications.     

Electrodeposition of sol-enhanced nanostructured Ni-TiO2 composite coatings

A novel electroplating method has been developed to produce nanocrystalline metal-matrix nano-structured composite coatings. A small amount of transparent TiO₂ sol was added into the traditional electroplating Ni solution, leading to the formation of nanocrystalline Ni-TiO₂ composite coatings. These coatings have a smooth surface. The Ni nodules changed from traditional pyramid-like shape to spherical shape. The grain size of Ni was also significantly reduced to the level of 50 nm. It was found that the amorphous anatase TiO₂ nano-particles (∼ 10 nm) were highly dispersed in the coating matrix. The microhardness was significantly increased from 320 HV₁₀₀ of the traditional Ni coating to 430 HV₁₀₀ of the novel composite coating with 3.26 wt.% TiO₂. Correspondingly, the wear resistance of the composite coating was improved by ∼ 50%.     

Effect of TiO2 nanoparticles on anticorrosion property in amorphous Ni-P-Cr composite coating in artificial seawater and microbial environment

To obtain the composite with a function of corrosion resistance in seawater and microbial environment, we apply low toxic electrolyte which contained Cr³⁺ instead of Cr⁶⁺ as a chromium source to produce Ni-P-Cr/TiO₂, Ni-P-Cr/ZrO₂ nanocomposite coatings, and Ni-P-Cr/TiO₂ microcomposite coating using direct current (DC) electrodeposits technique. The surface morphology, texture, and composition of the composite coatings are characterized by SEM, XRD, and EDX measurements, respectively. The corrosion behavior of the composite coatings is evaluated by polarization curves and electrochemical impedance spectroscopy (EIS). The results with more positive-shifting E_corr, lowest i_corr, and relatively high value of polarization resistance (R_p) proved that compared with other composite coatings, Ni-P-Cr/TiO₂ nanocomposite coating with its better passive film and unique antibacterial activity caused by TiO₂ nanoparticles incorporated, displayed excellent antibacterial and corrosion resistance property, consistent to the phenomenon that corrosion of this nanocomposite coating in SRB culture medium is not observed.     

Fabrication of Nano-TiO2 Coating for Dye-Sensitized Solar Cell by Vacuum Cold Spraying at Room Temperature

Deposition of nanocrystalline TiO₂ coating at low temperature is becoming more attractive due to the possibility for continuous roll production of the coating for assembly lines of dye-sensitized solar cell (DSC) at a low cost. In this study, porous nano-TiO₂ coating was deposited by vacuum cold spraying (VCS) at room temperature on a conducting glass substrate using commercial P25 nanocrystalline TiO₂ powder. The microstructure of TiO₂ coating was characterized by field emission scanning electron microscopy (FESEM) and nitrogen adsorption test. A commercial dye (N719) was adsorbed on the surface of TiO₂ particles within the coating to assemble a DSC. The cell performance was evaluated by employing simulated solar light at an intensity of 100 mW/cm². The results showed that TiO₂ coating was deposited by the agglomerates of nano-TiO₂ powders. The Brunauer-Emmett-Teller (BET) test of the as-sprayed TiO₂ coating yielded a porosity of 49% and an average pore size of 17 nm. The assembled solar cell yielded a short-circuit current density of 7.3 mA/cm² and an energy conversion efficiency of 2.4%. The test results indicate that VCS was a promising method to deposit nanocrystalline TiO₂ coatings at low temperature applied to DSCs. This article is an invited paper selected from presentations at the 2007 International Thermal Spray Conference and has been expanded from the original presentation. It is simultaneously published in Global Coating Solutions, Proceedings of the 2007 International Thermal Spray Conference, Beijing, China, May 14-16, 2007, Basil R. Marple, Margaret M. Hyland, Yuk-Chiu Lau, Chang-Jiu Li, Rogerio S. Lima, and Ghislain Montavon, Ed., ASM International, Materials Park, OH, 2007.     

The preparation and characteristics of a rare earth/nano-TiO2 composite coating on aluminum alloy by brush plating

Nano-TiO₂ modified rare earth composite coatings are prepared on 2024 aluminum alloy by brush plating. The composite coating is composed of mainly Ce(OH)₃, Ce(OH)₄, CeO₂ and TiO₂, with less cracks and lower porosity. The addition of nano-TiO₂ enhances the adhesive strength of the rare earth coating to Al substrate, results in refined coating grains and increases the micro-hardness of the coating. The nano-TiO₂ modification obviously improves the corrosion resistance of the rare earth coating. For the composite coating containing 2% TiO₂, both the corrosion current density and the impedance are reduced by more than one order of magnitude in contrast to the values for the pure rare earth coating. The higher barrier ability and increased Ce³⁺ content in the Ce oxides may explain the increase of the corrosion resistance.     

Functionally graded carbon nanotubes/hydroxyapatite composite coating by laser cladding

Functionally graded carbon nanotubes/hydroxyapatite (CNTs/HA) composite coatings have been fabricated by laser cladding technique using CNTs/HA composite powders. As the feedstock for laser deposition, CNTs/HA composite powders were prepared by ball-milling different weight ratios (1%, 3% and 5%) of CNTs with HA powders. CNTs/HA composite coatings were fabricated with CNTs/HA composite powders and functionally graded coating was fabricated by sequentially depositing different CNTs/HA composite coatings on pure titanium. The phase composition, microstructure, micro-hardness, bonding strength and in vitro cellular responses of the composite coatings and the functionally graded composite coating were studied. The results show that the crystallinity of CNTs/HA composite coatings increased with increasing amount of CNTs in the powder mixture. The CNTs were dispersed homogeneously in the coatings to form an interconnected web and the cylinder graphic structure of CNTs was not changed after laser irradiation. Compared with pure HA coating, the maximum increase of the micro-hardness of CNTs/HA composite coatings was 46.8% and the micro-hardness of the functionally graded coating increased gradually through the thickness of this coating. Furthermore, the bonding strength of the functionally graded coating was nearly twice higher than that of pure HA coating. The in vitro cellular biocompatibility tests reveal that the functionally graded composite coating has comparable in vitro bioactivity with pure HA coating.