Real gas choked flow conditions at low reduced-temperatures

Real gas choked mass flux is calculated for a frictionless stream expanding isentropically until it reaches the speed of sound and without phase changes. The other parameters associated with the choked state are the pressure, density, temperature ratios, and the speed of sound. Departure of the choked mass flux from the ideal gas model is discussed first in absolute terms and then in relative terms, using the Principle of Corresponding States, for gases with boiling points in the low temperature range. Reduced-stagnation pressures are examined up to values of 30 for hydrogen, neon, nitrogen, argon, methane, krypton, xenon, and R-14 and up to 100 for ⁴He. The corresponding reduced-stagnation temperatures go down to 1.4 and in some cases down to 1.2 for nitrogen and argon. Also discussed are the limiting values of stagnation parameters for which no phase change occurs in the choked state. Compared to the ideal gas, the mass flux may almost double and the critical pressure ratio may decrease by an order of magnitude. The relevance of results is discussed qualitatively and quantitatively for Joule-Thomson cryocooling.     

As-cast microstructures and behavior at high temperature of chromium-rich cobalt-based alloys containing hafnium carbides

Hafnium is often used to improve the high temperature oxidation resistance of superalloys but not to form carbides for strengthen them against creep. In this work hafnium was added in cobalt-based alloys for verifying that HfC can be obtained in cobalt-based alloys and for characterizing their behavior at a very temperature. Three Co–25Cr–0.25 and 0.50C alloys containing 3.7 and 7.4 Hf to promote HfC carbides, and four Co–25Cr– 0 to 1C alloys for comparison (all contents in wt.%), were cast and exposed at 1200 °C for 50 h in synthetic air. The HfC carbides formed instead chromium carbides during solidification, in eutectic with matrix and as dispersed compact particles. During the stage at 1200 °C the HfC carbides did not significantly evolve, even near the oxidation front despite oxidation early become very fast and generalized. At the same time the chromium carbides present in the Co–Cr–C alloys totally disappeared in the same conditions. Such HfC-alloys potentially bring efficient and sustainable mechanical strengthening at high temperature, but their hot oxidation resistance must be significantly improved.     

Equipment using a “static-analytic” method for solubility measurements in potentially hazardous binary mixtures under cryogenic temperatures

A new apparatus designed to study, at cryogenic temperatures, thermodynamic equilibria of potentially explosive binary systems such as hydrocarbon-oxygen mixtures is described herein. This equipment has an equilibrium cell which was especially designed to minimize hazards while allowing accurate phase equilibrium measurements. Reliability of results, obtained with this equipment has been verified by working on the nitrogen-propane system, for which data are already available in literature, over a large range of compositions and at various temperatures. Four isothermal curves describing liquid phase compositions at 109.98, 113.77, 119.75 and 125.63 K have been determined. Our experimental data are represented within 2% in compositions and in pressures through the Peng-Robinson equation of state implying Mathias-Copeman alpha function and Huron-Vidal mixing rule. Comparisons to literature allow pointing out: good agreement is observed with Kremer and Knapp data (1983) while the three sets of Poon and Lu data (1974) presenting systematic positive deviation are consequently judged as suspicious.     

Chitosan-collagen/organomontmorillonite scaffold for bone tissue engineering

A novel composite scaffold based on chitosan-collagen/organomontmo-rillonite (CS-COL/OMMT) was prepared to improve swelling ratio, biodegradation ratio, biomineralization and mechanical properties for use in tissue engineering applications. In order to expend the basal spacing, montmorillonite (MMT) was modified with sodium dodecyl sulfate (SDS) and was characterized by XRD, TGA and FTIR. The results indicated that the anionic surfactants entered into interlayer of MMT and the basal spacing of MMT was expanded to 3.85 nm. The prepared composite scaffolds were characterized by FTIR, XRD and SEM. The swelling ratio, biodegradation ratio and mechanical properties of composite scaffolds were also studied. The results demonstrated that the scaffold decreased swelling ratio, degradation ratio and improved mechanical and biomineralization properties because of OMMT.     

Capacitance based mass metering for cryogenic fluids

This paper describes a method for measuring the mass of cryogenic fluids in on-board rocket propellant tanks or ground storage tanks. Linear approximations to the Clausius-Mossotti relationship serve as the foundation for a capacitance based mass sensor, regardless of fluid density stratification or tank shape. Sensor design considerations are presented along with the experimental results for a capacitance based mass gage tested in liquid nitrogen. This test data is shown to be consistent with theory resulting in a demonstrated mass measurement accuracy of ±0.75% and a deviation from linearity of less than ±0.30% of full scale mass. Theoretical accuracies are also shown to be ±0.73% for hydrogen and ±1.39% for oxygen for a select range of pressures and temperatures.     

Gas gap thermal switches using neon or hydrogen and sorption pump

The very low pressure obtained thanks to adsorption phenomenon at low temperature can be used to build cryogenic heat switches, which offer the possibility to make or break thermal contact between two parts of a cryogenic system. The ON (conducting) and OFF (insulating) states of the switch are obtained by varying the gas pressure between two copper blocks separated by a gap of 100 μm. This pressure is controlled by acting upon the temperature of a small sorption pump (activated charcoal) connected to the gap space. For a “high” sorption pump temperature, the gas previously adsorbed in the sorption pump is released to the gap between the two blocks, allowing a good thermal conduction through the gas (ON state). On the opposite, cooling the sorption pump allows a very good vacuum between the copper blocks, which efficiently break the thermal contact (OFF state). Experimental thermal characteristics (Conductance in the ON and OFF state, ON-OFF switching temperature) of such a “Gas Gap Heat Switch” are described using hydrogen or neon as exchange gas and are compared with theoretical calculations.     

Development of a miniature cryogenic fluid circuit and a cryogenic micropump

This article presents the development of a miniaturized cryogenic fluid circuit for distributed cooling of low-temperature tracking detectors in high-energy physics (HEP). The heart of the circuit is a prototype cryogenic micropump. This volumetric pump is compatible with cooling powers of about 10-100 W, and capable of producing pressure heads of up to around 0.3 MPa. Besides detector and electronics cooling in HEP, potential applications are found in the field of superconductor technology.     

A review of experimental methods for solid solubility determination in cryogenic systems

Over the past years, there have been a number of serious explosions in air industry, which have resulted in workers injuries and fatalities. At the same time, there has been an increase in the use of air separation products for industrial activities.The quality of air entering an air separation plant is of crucial importance for its safe and reliable operation and the interest in the solubility data of solids in cryogenic liquid solvents is closely connected to the problem of impurities accumulation in the process plant and storage tanks. Such accumulations, especially in liquid oxygen, may cause fouling and blockage in heat exchangers and pipelines and they may eventually cause serious explosions. For this reason the air contaminants composition in liquid oxygen must be determined with great precision.This paper aims at reviewing experimental methods for determining the solubility of solid compounds that may be present in the cryogenic liquefaction processing of air distillation. A review of the literature data on solubility of solids in liquid oxygen and nitrogen is included as well.Emphasis is given to the difficulties in setting-up measuring apparatuses working at extreme conditions, i.e. low compositions and low temperatures.     

Low-power cryocooler survey

A cryocooler survey has been performed on data of 235 cryocoolers, with cooling powers below some tens of watts and operating between 4 and 120 K. The state-of-the-art is discussed and trends are investigated on cooling performance, mass and size, cost, lifetime and reliability. The data were compared with earlier surveys to explore historical trends. Improvements in cooling performance were mainly in 80 K cryocoolers, an increase in efficiency by about a factor of 5. Coolers did not reduce in size significantly. Main reduction was in 80 K coolers because of the higher efficiency. In the survey, cost is related to input power, cooling power and operating temperature. Cost development is considered and related to learning curves. Since the mid-90s, the lifetime of Stirling-type cryocoolers has increased by one order of magnitude from typically 0.5 to 5 years or more. The confusion that exists on the term “reliability” is discussed.     

Integrated Resonant Self-Pumped Loop and pulse tube cryocooler for cryogenic cooling distribution

Cooling distribution is a vital technology concerning cryogenic thermal management systems for many future space applications, such as in-space, zero boil-off, long-term propellant storage, cooling infrared sensors at multiple locations or at a distance from the cryocooler, and focal-plane arrays in telescopes. These applications require a cooling distribution technology that is able to efficiently and reliably deliver cooling power (generated by a cryocooler) to remote locations and uniformly distribute it over a large-surface area. On-going efforts by others under this technology development area have not shown any promising results.This paper introduces the concept of using a Resonant Self-Pumped Loop (RSPL) integrated with the proven, highly efficient pulse tube cryocooler. The RSPL and pulse tube cryocooler combination generates cooling power and provides a distributive cooling loop that can be extended long distances, has no moving parts, and is driven by a single linear compressor. The RSPL is fully coupled with the oscillating flow of the pulse tube working fluid and utilizes gas diodes to convert the oscillating flow to one-directional (DC) steady flow that circulates through the cooling loop. The proposed RSPL is extremely simple, lightweight, reliable, and flexible for packaging. There are several requirements for the RSPL to operate efficiently. These requirements will be presented in this paper. Compared to other distributive cooling technologies currently under development, the RSPL technology is unique.     

Effect of cryogenic treatment on microstructure, mechanical and wear behaviors of AISI H13 hot work tool steel

This paper focuses on the effects of low temperature (subzero) treatments on microstructure and mechanical properties of H13 hot work tool steel. Cryogenic treatment at −72 °C and deep cryogenic treatment at −196 °C were applied and it was found that by applying the subzero treatments, the retained austenite was transformed to martensite. As the temperature was decreased more retained austenite was transformed to martensite and it also led to smaller and more uniform martensite laths distributed in the microstructure. The deep cryogenic treatment also resulted in precipitation of more uniform and very fine carbide particles. The microstructural modification resulted in a significant improvement on the mechanical properties of the H13 tool steel.     

Percolation and the resistive transition of the critical temperature Tc of Nb3Sn

The relationship between the distribution of the critical temperature, the percolation function, and the resistive transition of the critical temperature is explored for polycrystalline Nb₃Sn. In the neighborhood of the critical temperature, Nb₃Sn is assumed to be a random mixture of superconducting and normal grains. Percolation concepts are applied to a study of the resistivity. A general analysis is made showing that the onset and shape of the resistive transition for composite conductors are determined by the percolation function and the distribution of the critical temperature. An approximate form of the percolation function is determined based on a linear FEM analysis. Example resistive transitions are calculated for an assumed normal distribution of the critical temperature. An argument is presented that relates grain orientation and strain dependence in Nb₃Sn. It is noted that a dependence of the distribution of T_c with strain, in addition to the usual shift in T_c with strain, would be the result of a strain dependence that is a function of grain orientation. The analysis shows the extent to which the slope of the resistive transition is a measure of the distribution of the critical temperature, and therefore a measure of the grain orientation strain sensitivity. Finally, a method is described to determine the percolation function experimentally.     

Analysis of optimum configuration of two-stage thermoelectric modules

In this paper, the theoretical analysis and stimulating calculation were conducted for a basic two-stage thermoelectric module, which contains one thermocouple in the second stage and several thermocouples in the first stage. The study focused on the configuration of the two-stage thermoelectric module, especially investigating the influences of some parameters, such as the allocation of the junction temperature difference in the module, the length of thermocouples and the number of thermocouples, on the cooling performance of the module. The obtained analysis results indicate that changing the junction temperature difference in the second stage, the length of thermocouples and the number of thermocouples in the first stage can improve the cooling performance of the module. These results can be used to optimize the configuration of the two-stage thermoelectric module, and provide guides for the design and application of thermoelectric cooler.     

JackPot: A novel model to study the influence of current non-uniformity and cabling patterns in cable-in-conduit conductors

JackPot is a new model that is used to analyse how and to what extend current non-uniformity among strands in a cable-in-conduit conductor (CICC) affects its performance. The joints at the extremities of the CICCs in coils and short samples introduce a non-uniform current distribution among the strands. A detailed and quantitative study down to strand level is required to explain the involved phenomena, to understand their implications on short sample and coil tests and to provide adequate solutions for improvements. The model can be used to evaluate the influence of the joint design and to define its baseline requirements for short-sample qualification testing, and for optimum magnet performance of for example the ITER coils.JackPot is an electrical network model that simulates the interaction between the superconducting strands in the cable (following their precise trajectories), the interstrand contact resistances, the conduit, and the cable’s connection to the joints. The backbone of JackPot is its cable geometry model, from which all relevant properties are derived. All parameters are derived from well defined experimental measurements on conductor sections and joints, except the axial strain for Nb₃Sn strands, which is the only free parameter in the model.The simulations demonstrate that the current non-uniformity is the source for a number of observed phenomena. Another conclusion is that completely filling the bottom joints and upper terminations of a short sample with solder, opposed to only (partly) soldering the cable surface, improves short-sample testing significantly for qualifying the ITER type CICCs. This paper describes the model and gives a few examples of applications for its validation.     

Low temperature radiative properties of materials used in cryogenics

Radiative heat transfer between two parallel surfaces, a sample surface and a black surface, was measured. One of the surfaces was cooled with liquid helium to about 5 K and the other one was step by step heated to temperatures ranging between 30 and 140 K. As a result, the total hemispherical absorptivity and emissivity of the sample surface were determined in dependence on the temperature of the heat radiation. Aluminium samples were made of Al sheet, Al foil and aluminized mylar. Further measurements were performed on sheets of aluminium alloy, Cu, zinc brass and stainless steel. The influence of different types of sample treatment such as chemical and mechanical surface finishing and material annealing on the radiative properties is presented.     

Fracture and deformation properties of Ni-Fe superalloy in cryogenic high magnetic field environments

The present paper includes experimental and analytical data on the fracture properties of a nickel-iron superalloy, a ferromagnetic austenite, at 4 K in magnetic fields of 0 and 6 T. The tensile, notch tensile and small punch tests are employed. A finite element analysis is also performed to convert the experimentally measured load-displacement data into useful engineering information. To interpret the results we review the available theory of the influence of magnetic field on the stress intensity factor for a crack in ferromagnetic materials.     

Liquid helium cryostat for SQUID-based MRI receivers

We describe a liquid helium cryostat, developed to cool SQUID-based receivers in low field MRI systems. The cryostat has a 4 L liquid helium capacity, a hold time of over 3 days and accommodates 10 cm diameter receiver coils. New vacuum insulation methods reduce the noise level by at least an order of magnitude compared to existing commercial designs. The minimum detectable field at 425 kHz, with a 5 cm diameter circular coil, was estimated to be 0.018 fT/Hz^1/2 from Q-factor measurements and 0.035 fT/Hz^1/2 by direct measurement with a SQUID amplifier. Further measurements indicated that most of this field noise probably originates with dielectric losses in the cryostat’s fibreglass shells.     

Application of microwave-assisted extraction to the analysis of PCBs and CBzs in fly ash from municipal solid waste incinerators

Polychlorinated biphenyls (PCBs) and chlorobenzenes (CBzs) are two classes of dioxin precursors formed in municipal solid waste incinerators (MSWIs) producing negative health effects similar to those of dioxins. Reducing the analytical time required for determining the concentrations of these compounds in MSWIs is important for quickly evaluating their importance and associated health risks. In the present study, microwave-assisted extraction (MAE) is compared with traditional Soxhlet extraction (SE) to determine the extraction efficiencies attained for PCB and CBz analysis. The efficiencies of MAE are compared with those of SE under various experimental conditions, using fly ash spiked with standards. Water is used as a safe and environmentally friendly solvent in MAE for PCB and CBz analyses and MAE has high extraction efficiency for spiked fly ash compared with that of SE. Furthermore, the extraction time and organic solvent consumption are reduced with MAE compared with SE. The optimum conditions for MAE established in this study are using a 30-ml volume of toluene/acetone (1/1) or a 15-ml volume of toluene, samples with less than 60% water content (WC), and an irradiation time of 15 min.     

Cryogenic propellant liquefaction and storage for a precursor to a human Mars mission

An analysis of cryogenic liquefaction and storage methods for in-situ produced propellants (oxygen and methane) on Mars is presented. The application is to a subscale precursor sample return mission, intended to demonstrate critical cryogenic technologies prior to a human mission. A heat transfer analysis is included, resulting in predicted cryogenic tank surface temperatures and heat leak values for different conditions. Insulation thickness is traded off against cryocooler capacity to find optimum combinations for various insulation configurations, including multilayer insulation and microspheres. Microsphere insulation is shown to have promise, and further development is recommended.