CO2 laser-assisted preparation of transparent Eu2Ti2O7 thin films

We present a laser-assisted preparation of transparent europium-titanate Eu₂Ti₂O₇ thin films with tailored structural and optical properties. We have evaluated the effects of the irradiation time on the structural and the optical properties of the films. This approach allows the preparation of nanocrystalline crack-free films and micro patterns. The amorphous thin films were prepared by a sol-gel method. The films were annealed by a CO₂ laser beam for various time intervals. The laser irradiation induced a crystallization process that resulted in the formation of Eu₂Ti₂O₇ nanocrystals. The nanocrystals regularly grew with increasing irradiation time reaching the size from 25?nm to 45?nm. A film of a thickness 480?nm exhibited an optical transmission of 91.9% that is close to the maximal theoretical limit. The film's refractive index at 632?nm was 2.26. A micrometric pattern was prepared by a direct laser writing followed by a wet chemical etching. Feasibility of the demonstrated approach, together with the high film's quality, and europium-titanate chemical resistivity open up many opportunities for advanced applications. The approach can be used for a preparation of protective coatings and integrated photonic devices such as planar optical waveguides and couplers.     

Citric based sol-gel synthesis and photoluminescence properties of un-doped and Sm doped Ca3Y2Si3O12 phosphors

The photoluminescent properties of un-doped and Sm³⁺ doped Ca₃Y₂Si₃O₁₂ phosphors were prepared by the citrate sol-gel method. Un-doped sample has shown a strong blue emission, which has its maximum intensity at 389 nm. Among all the observed emission transitions ⁴G_5/2→⁶H_J (J = 5/2, 7/2 & 9/2) of Sm³⁺, the reddish-orange (RO) emission transition ⁴G_5/2→⁶H_7/2 is more prominent, which matches well with the emission wavelength of near UV (n-UV) LED. The reasons for the observance of such prominent visible color emissions from these phosphors have been substantiated appropriately. Besides, structural details of these samples have also been analyzed from the measured XRD, TEM, TG-DTA and FT-IR profiles.     

Electrical properties of niobium doped Bi4Ti3O12-SrBi4Ti4O15 intergrowth ferroelectrics

Nb-doped Bi₄Ti₃O₁₂-SrBi₄Ti₄O₁₅ intergrowth ceramics have been prepared by modified oxalate route. XRD phase analysis confirmed the formation of single phase compound. Nb-doping does not affect the basic crystal structure of the intergrowth. SEM micrographs showed that the grain size of the ceramics decreases with Nb-doping. The temperature dependence of dielectric constant and losses was investigated in the temperature range 30–800 °C and frequency range 1 kHz–1 MHz. With Nb-doping, the T_c of the ferroelectrics reduces and peak permittivity increases. Doping also introduces small relaxor behavior in the ferroelectrics. The dc conductivity of the ceramics decreases with doping. The remnant polarization (P_r) of the intergrowth ferroelectrics is increased with Nb doping.     

Microwave assisted sintering of CaCu3Ti4O12

CaCu₃Ti₄O₁₂ electroceramic was prepared by a microwave assisted solid-state reaction technique from CaCO₃, CuO and TiO₂ powders. Processing involved the preparation of raw material, mixing and milling, calcination, pellet forming and sintering processes. Conventional furnace and microwave assisted sintering processes were employed in order to improve phase structures, morphology and dielectric properties of CaCu₃Ti₄O₁₂ ceramics. Surface and fracture FESEM analysis showed that the microwave assisted sintered CaCu₃Ti₄O₁₂ produced better densification and more uniform grain size compared to the conventional sintered sample.     

Synthesis and characterization of CaFe2O4 nanoparticles via co-precipitation and auto-combustion methods

In this paper, the techniques for the synthesis of CaFe₂O₄ nanoparticles using the auto-combustion and co-precipitation methods are discussed. The effects of both methods on the microstructure and magnetic properties of the CaFe₂O₄ nanoparticles were compared. The CaFe₂O₄ powder was obtained after drying the synthesized sample via co-precipitation overnight in an oven at 80 °C. For auto-combustion method, the sol that was initially formed was gradually converted into a gel, which was then combusted at 250 °C. Finally, the CaFe₂O₄ nanoparticles were calcined at 550 °C. The different synthesis methods produced nanoparticles with different physical and magnetic properties in order to find an optimum size to be utilized for drug delivery applications. The results of the X-ray diffraction showed that both processes produced nanocrystals with an orthorhombic crystalline structure. It was noted from the measurements made with a transmission electron microscope (TEM) that the synthesis using the co-precipitation method produced nanoparticles with a size of about 10–20 nm, which was comparable with the size that was obtained when the auto-combustion method was used. The magnetic properties were investigated using a vibrating sample magnetometer (VSM), where the magnetic saturation (M_s) of CaFe₂O₄ for the sample synthesized using the co-precipitation method was 47.279 emu/g, which was higher than the magnetic saturation (M_s) of 31.10 emu/g obtained when the auto-combustion method was used. The hysteresis loops (Hc) for the samples were 17.380 G and 6.1672 G, respectively. Additionally, the elaborate properties mentioned above, such as the size and superparamagnetic properties of the synthesized CaFe₂O₄ nanoparticle size, were the characteristics required for drug delivery because the targeted therapy required nanoparticles with good magnetic properties, a suitable size, and which were non-toxic in order to have a potential application in targeted drug delivery systems.     

Investigation on the origin of the giant dielectric constant in CaCu3Ti4O12 ceramics through analyzing CaCu3Ti4O12-HfO2 composites

A full range of CaCu₃Ti₄O₁₂-HfO₂ (CCTO-HfO₂) composites were prepared by sintering mixtures of the two components at 1000 °C for 10 h. X-ray diffraction studies confirmed the two-phase nature of the composites. The evolution of the microstructure in the composites, in particular, the size distribution of CCTO grains, was examined by scanning electron microscopy. The studies showed that, as more HfO₂ was added, the abnormal grain growth of CCTO and coarsening of the microstructure were gradually suppressed. As a result, the average CCTO grain size was reduced from 50 to 1 μm. The measured dielectric constants agree well with the values calculated from Lichtenecker's logarithmic law, using only the dielectric constants of pure CCTO and HfO₂ as two end points. The agreement suggests to us that the dielectric constant of CCTO is dominated by domain boundaries within the grains rather than by grain boundaries between the grains.     

Fabrication and properties of Mn1.56Co0.96Ni0.48O4 free-standing ultrathin chips

Mn_1.56Co_0.96Ni_0.48O₄ (MCN) free-standing ultrathin chips are successfully fabricated by using screen printing. The structure, electrical and IR absorption properties have been investigated as a function of the sintering temperature. The X-ray diffraction, X-ray photoelectron spectroscopy and field emission scanning electron microscope analyses show remarkable improvements in crystallinity, stoichiometry and relative density for MCN chips. From the electrical experimental results, it is found that the resistivity of the chip samples sharply decreases from 2660 to 21.9 Ω cm. Such feature is attributed to the decrease in the grain boundary resistance and the increase in Mn³⁺/Mn⁴⁺ ratio with increasing sintering temperature. Furthermore, Fourier transform infrared spectra show that the absorption bands ν1 (around 1160 cm⁻¹) at 1100 °C almost disappears while the others still remain. It is ascribed to the increase in the density of samples. The intensities of symmetry bands ν2 (850 cm⁻¹) are also found to be consistent with an increase in ratio of Mn³⁺ to Mn⁴⁺ ions with increasing sintering temperature.     

Effects of Al2O3 addition on the microstructure and microwave dielectric properties of Ba4Nd9.33Ti18O54 ceramics

Ba₄Nd_9.33Ti₁₈O₅₄·x wt%Al₂O₃ (BNT-A) ceramics (x=0, 0.5, 1.0, 1.5, 2.0, 2.5) were prepared by the conventional solid state reaction. The effects of Al₂O₃ on the microstructure and microwave dielectric properties of Ba₄Nd_9.33Ti₁₈O₅₄ (BNT) ceramics were investigated. X-ray diffraction and backscatter electronic images showed that the Al₂O₃ additive gave rise to a second phase BaAl₂Ti₅O₁₄ (BAT). The formation mechanism and grain growth of the BAT phase were first discussed. Dielectric property test revealed that the Al₂O₃ additive had improved the dielectric properties of the BNT ceramics: increased the Q×f value from 8270 to 12,180 GHz and decreased the τ_f value from 53.4 to 11.2 ppm/°C. A BNT-A ceramic with excellent dielectric properties: ε_r=70.2, Q×f=12,180 GHz, τ_f=20 ppm/°C was obtained with 2.0 wt% Al₂O₃ added after sintering at 1320 °C for 4 h.     

Synthesis of ultradisperse NiFe2O4 spinel by thermal decomposition of citrate precursors and its magnetic properties

Peculiarities of synthesis of nanocrystalline NiFe₂O₄ powders by thermal decomposition of citrate precursors were investigated. It was found that the parameters of nanopowders are determined by the decomposition temperature and pH of the precursor media. The temperature and duration of the process of precursor decomposition are limiting factors for decrease of the grain size. An optimum relation between the limiting factors can be determined experimentally by variation of pH. Correlation between the synthesis parameters, particle size, and magnetic properties is discussed. It is shown that optimum magnetic and magnetostrictive properties were found for the bulk polycrystalline samples sintered using the powders obtained for pH 2.     

Temperature dependence of piezoelectric properties on Nd and V co-substituted Bi4Ti3O12 ceramics for ceramic resonator applications

The temperature dependences of the piezoelectric properties of (Bi_4−yNd_y)_1−(x/12)(Ti_3−xV_x)O₁₂ [BNTV-x, y (x = 0.01, y = 0.00–1.00)] were investigated for environmentally friendly lead-free piezoelectric ceramic resonators with low-temperature coefficients of resonance frequency, TC-f. The |TC-f| in the (33) mode improved with increasing concentration of modified Nd ions, y, and exhibited the smallest |TC-f| value of 77.4 ppm/°C at y = 0.75 (BNTV-0.75). The |TC-f| in the other vibration mode (t), was also investigated for the BNTV-0.75 ceramic, and a smaller value of 42 ppm/°C was obtained. The (t) mode of the BNTV-0.75 ceramic showed excellent piezoelectric properties: Q_m = 4200, Q_e max = 31 and TC-f = −49.8 ppm/°C. These properties are very similar to those of commercialized hard PZT ceramics for resonator applications. The BNTV-0.75 ceramic seems to be a superior candidate material for lead-free piezoelectric applications of ceramic resonators.     

ZnLi2/3Ti4/3O4: A new low loss spinel microwave dielectric ceramic

A new low loss spinel microwave dielectric ceramic with composition of ZnLi_2/3Ti_4/3O₄ was synthesized by the conventional solid-state ceramic route. The ceramic can be well densified after sintering above 1075 °C for 2 h in air. X-ray diffraction data show that ZnLi_2/3Ti_4/3O₄ ceramic has a cubic structure [Fd-3m (227)] similar to MgFe₂O₄ with lattice parameters of a = 8.40172 Å, V = 593.07 Å³, Z = 8 and ρ = 4.43 g/cm³. The best microwave dielectric properties can be obtained in ceramic with relative permittivity of 20.6, Q × f value of 106,700 GHz and τ_f value of −48 ppm/°C. The addition of BaCu(B₂O₅) (BCB) can effectively lower the sintering temperature from 1075 °C to 900 °C and does not induce much degradation of the microwave dielectric properties. Compatibility with Ag electrode indicates that the BCB added ZnLi_2/3Ti_4/3O₄ ceramics are good candidates for LTCC applications.     

Preparation and characterization of three dimensionally ordered macroporous Li4Ti5O12 anode for lithium batteries

Three dimensionally ordered macroporous (3DOM) Li₄Ti₅O₁₂ membrane (80 μm thick) was prepared by a colloidal crystal templating process. Colloidal crystal consisting of monodisperse polystyrene particles (1 μm diameter) was used as the template for the preparation of macroporous Li₄Ti₅O₁₂. A precursor sol consisting of titanium isopropoxide and lithium acetate was impregnated into the void space of template, and it was calcined at various temperatures. A macroporous membrane of Li₄Ti₅O₁₂ with inverse-opal structure was successfully prepared at 800 °C. The interconnected pores with uniform size (0.8 μm) were clearly observed on the entire part of membrane. The electrochemical properties of the three dimensionally ordered Li₄Ti₅O₁₂ were characterized with cyclic voltammetry and galvanostatic charge and discharge in an organic electrolyte containing a lithium salt. The 3DOM Li₄Ti₅O₁₂ exhibited a discharge capacity of 160 mA h g⁻¹ at the electrode potential of 1.55 V versus Li/Li⁺ due to the solid state redox of Ti^3+/4+ accompanying with Li⁺ ion insertion and extraction. The discharge capacity was close to the theoretical capacity (167 mA h g⁻¹), which suggested that the Li⁺ ion insertion and extraction took place at the entire part of 3DOM Li₄Ti₅O₁₂ membrane. The 3DOM Li₄Ti₅O₁₂ electrode showed good cycle stability.     

Structural and luminescence properties of RE (RE = Eu, Tb):(MgCa)2Bi4Ti5O20 ceramics

Rare-earth ions (Eu³⁺, Tb³⁺) activated magnesium calcium bismuth titanate [(MgCa)₂Bi₄Ti₅O₂₀] ceramics were prepared by conventional solid state reaction method for their structural and luminescence properties. By using XRD patterns, the structural properties of ceramic powders have been analyzed. Emission spectrum of Eu³⁺:(MgCa)₂Bi₄Ti₅O₂₀ ceramic powder has shown strong red emission at 615 nm (⁵D₀ → ⁷F₂) with an excitation wavelength λ_exci = 393 nm and Tb³⁺:(MgCa)₂Bi₄Ti₅O₂₀ ceramic powder has shown green emission at 542 nm (⁵D₄ → ⁷F₅) with an excitation wavelength λ_exci = 376 nm. In addition, from the measurements of scanning electron microscopy (SEM), Fourier transform-infrared (FTIR) and energy dispersive X-ray analysis (EDAX) results the morphology, structure and elemental analysis of these powder ceramics have been studied.     

Synthesis of nano-sized Yb3Al5O12 powders by the urea co-precipitation method

Nano-sized polycrystalline ytterbium aluminum garnet (YbAG, Yb₃Al₅O₁₂) powders were successfully synthesized by a simple urea co-precipitation method. The thermal behavior of the YbAG precursor was investigated. The calcined amorphous YbAG precursor was directly converted to 20–30 nm monophase YbAG at as low as temperature 900 °C, without any other intermediate phases. The nano-sized YbAG powders calcined at 900 °C distributed evenly with a slight aggregation, and the specific surface area of the powders reached 29.7 m² g⁻¹. The absorption spectrum of the YbAG powders was measured, and there were two strong absorption peaks centered at 931 and 965 nm. The results did not correspond to the absorption peaks of Yb:YAG crystal exactly, as the lattice parameters were different between YbAG and YAG.     

Synthesis of high efficiency Zn2SiO4:Mn green phosphors using nano-particles

In this study, Zn₂SiO₄:Mn²⁺ luminescent phosphors were prepared by mixing nano-scale ZnO, SiO₂, and MnO₂ particles at the compositions corresponding to 2ZnO + SiO₂ + X mol% MnO₂ (Zn₂SiO₄–X-MnO₂, 0.02 ≤ X ≤ 0.05). The mixing powders were calcined from 900 °C to 1300 °C in air and in N₂ atmosphere. No matter calcined in air or in N₂ atmosphere, Zn₂SiO₄ was the mainly crystalline phase in particles calcined at 900 °C and was the only phase in particles calcined at 1000 °C and higher. The influences of MnO₂ concentration and calcining atmosphere and temperature on wavelength of luminescence peak and the emission intensity were further intensively investigated. We would show that the calcining atmosphere had no apparent influences on the physical and photoluminescence (PL) characteristics of Zn₂SiO₄:Mn²⁺ phosphors. The MnO₂ content and the calcining temperature were the main reasons to influence the physical and PL characteristics of Zn₂SiO₄:Mn²⁺ phosphors.     

Effect of Bi2O3 additives on sintering and microwave dielectric behavior of La(Mg0.5Ti0.5)O3 ceramics

Bi₂O₃ was selected as liquid phase sintering aid to lower the sintering temperature of La(Mg_0.5Ti_0.5)O₃ ceramics. The sintering temperature of La(Mg_0.5Ti_0.5)O₃ ceramics is generally high, about 1600 °C. However, the sintering temperature was significantly lowered about 275 °C from 1600 °C to 1325 °C by incorporating in 15 mol% Bi₂O₃ and revealed the optimum microwave dielectric properties of dielectric constant (?_r) value of 40.1, a quality factor (Q × f) value of 60,231 GHz, and the temperature coefficient (τ_f) value of 70.1 ppm/°C. During all addition ranges, the relative dielectric constants (?_r) were different and ranged from 32.0 to 41.9, the quality factors (Q × f) were distributed in the range of 928–60,231 GHz, and the temperature coefficient (τ_f) varies from 0.3 ppm/°C to 70.3 ppm/°C. Noticeably, a nearly zero τ_f can be found for doping 5 mol% Bi₂O₃ sintering at 1325 °C. It implies that nearly zero τ_f can be achieved by appropriately adjusting the amount of Bi₂O₃ additions and sintering temperature for La(Mg_0.5Ti_0.5)O₃ ceramics.     

Response characteristics of all-solid-state pH sensor using Li5YSi4O12 glass

A new type of all-solid-state pH sensor was investigated for the monitoring of pH in high temperature. The all-solid-state pH sensor consists of two half-cells: indicator electrode using the Li₅YSi₄O₁₂ glass and an Ag/AgCl reference electrode coated with Nafion film. A stable Nafion film was achieved by heat treating at 100 °C for 1 h. The electromotive force (EMF) of the all-solid-state pH sensor decreased linearly with pH increase in water in accordance with the Nernst's equation. The all-solid-state pH sensor operated stably up to 80 °C. The sensitivity of the all-solid-state pH sensor against pH was high, and the EMF was also scarcely influenced by the presence of inorganic ions such as Li⁺, Na⁺ and Cl⁻. It was practically confirmed by the pH titration test that the all-solid-state pH sensor behaved similar to the commercial pH meter with the conventional glass electrode. In addition, the all-solid-state pH sensor showed same equivalence point both at high temperature and low temperature operations.     

Effect of La substitution on the structural and electrical properties of BaBi4−xLaxTi4O15

Pure and lanthanum doped barium bismuth titanate BaBi_4−xLa_xTi₄O₁₅ (BBLT, x=0, 0.05, 0.15, 0.30) ceramics were prepared utilizing solid state method. The X-ray diffraction (XRD) data confirmed formation of single-phase Aurivillius compounds while SEM micrographs did not show evident grain size change of doped ceramics. Dielectric properties were investigated in 1.21 kHz to 1 MHz frequency range and in the temperature range of 20 to 727 °C. When Bi³⁺ is substituted with La³⁺, a significant disorder was induced and the material exhibited broadening of the phase transition. Impedance analysis confirmed the presence of two semicircular arcs in doped samples suggesting the existence of grain and grain-boundary conduction. The dc-conductivity and activation energies were evaluated for all compositions.     

Microstructural, electrical and magnetic properties of multiferroic CoFe2O4/0.68Pb(Mg1/3Nb2/3)O3-0.32PbTiO3 nanocomposite thin films

Bilayered CoFe₂O₄/0.68Pb(Mg_1/3Nb_2/3)O₃-0.32PbTiO₃ nanocomposite films are successfully prepared on Pt/Ti/SiO₂/Si substrate via simple sol-gel process. X-ray diffraction result reveals that there exists no chemical reaction or phase diffusion between the CoFe₂O₄ and 0.68Pb(Mg_1/3Nb_2/3)O₃-0.32PbTiO₃ phases. The microstructure is characterized by scanning/transmission electron microscopy (STEM). The composite thin films exhibit both strong ferroelectric and ferromagnetic responses at room temperature. The maximal magnetoelectric coupling coefficient of the nanocomposite films reaches up to 25 mV/cm Oe, occurs at a lower bias magnetic field (H_dc) of 550 Oe.     

Effect of Bi2O3 and B2O3 additives on the sintering temperature, microstructure, and microwave dielectric properties for Sm(Mg0.5Ti0.5)O3 ceramics

The microwave dielectric properties of Sm(Mg_0.5Ti_0.5)O₃ incorporated with various amount of Bi₂O₃ and B₂O₃ additives have been investigated systematically. In this study, both Bi₂O₃ and B₂O₃ additives acting as a sintering aid can effectively lower the sintering temperature from 1550 °C to 1300 °C. The ionic radius of Bi³⁺ for a coordination number of 6 is 0.103 nm, whereas the ionic radius of B³⁺ is 0.027 nm. Clearly, the ionic radius of Bi³⁺ is greatly larger than one of B³⁺, which resulted in the specimens incorporated with Bi₂O₃ having larger lattice parameters and cell volume than those incorporated with B₂O₃. The experimental results show that no second phase was observed throughout the entire experiments. Depending on the interfacial tension, the liquid phase may penetrate the grain boundaries completely, in which case the grains will be separated from one another by a thin layer as shown in Sm(Mg_0.5Ti_0.5)O₃ ceramics incorporated with Bi₂O₃. Whereas, in Sm(Mg_0.5Ti_0.5)O₃ ceramics incorporated with B₂O₃, the volume fraction of liquid is high, the grains may dissolve into the liquid phase, and rapidly rearrange, in which case contact points between agglomerates will be dissolved due to their higher solubility in the liquid, leading plate-like shape microstructure.A dielectric constant (?_r) of 29.3, a high Q × f value of 26,335 GHz (at 8.84 GHz), and a τ_f of −32.5 ppm/°C can be obtained for Sm(Mg_0.5Ti_0.5)O₃ ceramics incorporated with 10 mol% Bi₂O₃ sintered at 1300 °C. While Sm(Mg_0.5Ti_0.5)O₃ ceramics incorporated with 5 mol% B₂O₃ can effectively lower temperature coefficient of resonant frequency, which value is −21.6 ppm/°C. The Sm(Mg_0.5Ti_0.5)O₃ ceramic incorporated with heavily Bi₂O₃ and B₂O₃ additives exhibits a substantial reduction in temperature (∼250 °C) and compatible dielectric properties in comparison with that of an un-doped one. This implied that this ceramic is suitable for miniaturization in the application of dielectric resonators and filters by being appropriately incorporated with a sintering aid.