Effects of annealing temperature on the photocatalytic activity of N-doped TiO2 thin films

The effects of annealing temperature on the photocatalytic activity of nitrogen-doped (N-doped) titanium oxide (TiO₂) thin films deposited on soda-lime-silica slide glass by radio frequency (RF) magnetron sputtering have been studied. Glancing incident X-ray diffraction (GIAXRD), Raman spectrum, scanning electron microscopy (SEM), atomic force microscopy (AFM) and UV-vis spectra were utilized to characterize the N-doped TiO₂ thin films with and without annealing treatment. GIAXRD and Raman results show as-deposited N-doped TiO₂ thin films to be nearly amorphous and that the rutile and anatase phases coexisted when the N-doped TiO₂ thin films were annealed at 623 and 823 K for 1 h, respectively. SEM microstructure shows uniformly close packed and nearly round particles with a size of about 10 nm which are on the slide glass surface for TiO₂ thin films annealed at 623 K for 1 h. AFM image shows the lowest surface roughness for the N-doped TiO₂ thin films annealed at 623 K for 1 h. The N-doped TiO₂ thin films annealed at 623 K for 1 h exhibit the best photocatalytic activity, with a rate constant (k_a) of about 0.0034 h⁻¹.     

Effects of tungsten thickness and annealing temperature on the electrical properties of W-TiO2 thin films

TiO₂ thin films were prepared by RF magnetron sputtering onto glass substrates and tungsten was deposited onto these thin films (deposition time 15-60 s) to form W-TiO₂ bi-layer thin films. The crystal structure, morphology, and transmittance of these TiO₂ and W-TiO₂ bi-layer thin films were investigated. Amorphous, rutile, and anatase TiO₂ phases were observed in the TiO₂ and W-TiO₂ bi-layer thin films. Tungsten thickness and annealing temperature had large effects on the transmittance of the W-TiO₂ thin films. The W-TiO₂ bi-layer thin films with a tungsten deposition time of 60 s were annealed at 200 °C-400 °C. The band gap energies of the TiO₂ and the non-annealed and annealed W-TiO₂ bi-layer thin films were evaluated using (αhν)^1/2 versus energy plots, showing that tungsten thickness and annealing temperature had major effects on the transmittance and band gap energy of W-TiO₂ bi-layer thin films.     

Shock-consolidated TiO2 bulk with pure anatase phases fabricated by explosive compaction using underwater shockwave

Titanium dioxide (TiO₂) bulk with pure anatase phases was fabricated by an explosive compaction technique using an underwater shockwave. Dynamic shock pressure of 6 GPa was used to consolidate anatase TiO₂ powders. Its microstructural, crystalline structural and photocatalytic characteristics were observed and measured by various techniques, such as X-ray diffraction (XRD), scanning electron microscopy (SEM) and photocatalytic activity measurement system. It was confirmed that the relative density of anatase TiO₂ compact is about 96% (3.73 g/cm³) of the theoretical density (3.89 g/cm³) and a strong surface bonding between particles is formed by a shock energy. In X-ray diffraction analysis, high purity anatase phases, broadened peaks due to lattice defects and decreased crystallite size were found. For the photocatalytic activities, the anatase TiO₂ compact was quite excellent compared to the commercial sintered TiO₂ bulk.     

Electrophoretic deposition of nanocrystalline TiO2 films on Ti substrates for use in flexible dye-sensitized solar cells

Nanocrystalline TiO₂ films were prepared on flexible Ti-metal sheets by electrophoretic deposition followed by chemical treatment with tetra-n-butyl titanate (TBT) and sintering at 450 °C. X-ray diffraction (XRD) analysis indicates that TBT treatment led to the formation of additional anatase TiO₂, which plays an important role in improving the interconnection between TiO₂ particles, as well as the adherence of the film to the substrate, and in modifying the surface properties of the nanocrystalline particles. The effect of TBT treatment on the electron transport in the nanocrystalline films was studied by intensity-modulated photocurrent spectroscopy (IMPS). An increase in the conversion efficiency was obtained for the dye-sensitized solar cells with TBT-treated nanocrystalline TiO₂ films. The cell performance was further optimized by designing nanocrystalline TiO₂ films with a double-layer structure composed of a light-scattering layer and a transparent layer. The light-scattering effect of the double-layer nanocrystalline films was evaluated by diffuse reflectance spectra. Employing the double-layer nanocrystalline films as the photoelectrodes resulted in a significant improvement in the incident photo-to-current conversion efficiency of the corresponding cells due to enhanced solar absorption by light scattering. A high conversion efficiency of 6.33% was measured under illumination with 100 mW cm⁻² (AM 1.5) simulated sunlight.     

Preparation of nanosized anatase TiO2-coated kaolin composites and their pigmentary properties

Nanosized anatase TiO₂-coated kaolin composites were prepared by the chemical deposition method starting from calcined kaolin and TiCl₄. The resultant TiO₂ nanoparticles on the kaolin surfaces existed in anatase phase after calcination at 200, 400, and 900 °C for 1 h, respectively. The surfaces of the kaolin powders were uniformly coated by a monolayer of TiO₂ nanoparticles. The higher calcination temperature was beneficial to formation of well crystallized anatase TiO₂ nanoparticles. The light scattering indexes of the TiO₂-coated calcined kaolin composites were two times higher than that of the kaolin substrate. XPS analysis shows that TiO₂ coating layers anchored at the kaolin surfaces via the Ti-O-Si and Ti-O-Al bonds.     

Lithium-ion battery anode properties of TiO2 nanotubes prepared by the hydrothermal synthesis of mixed (anatase and rutile) particles

From mixed (anatase and rutile) bulk particles, anatase TiO₂ nanotubes are synthesized in this study by an alkaline hydrothermal reaction and a consequent annealing at 300-400 °C. The physical and electrochemical properties of the TiO₂ nanotube are investigated for use as an anode active material for lithium-ion batteries. Upon the first discharge-charge sweep and simultaneous impedance measurements at local potentials, this study shows that interfacial resistance decreases significantly when passing lithium ions through a solid electrolyte interface layer at the lithium insertion/deinsertion plateaus of 1.75/2.0 V, corresponding to the redox potentials of anatase TiO₂ nanotubes. For an anatase TiO₂ nanotube containing minor TiO₂(B) phase obtained after annealing at 300 °C, the high-rate capability can be strongly enhanced by an isotropic dispersion of TiO₂ nanotubes to yield a discharge capacity higher than 150 mAh g⁻¹, even upon 100 cycles of 10 C-rate discharge-charge operations. This is suitable for use as a high-power anode material for lithium-ion batteries.     

Mesoporous polyaniline or polypyrrole/anatase TiO2 nanocomposite as anode materials for lithium-ion batteries

A functional composite as anode materials for lithium-ion batteries, which contains highly dispersed TiO₂ nanocrystals in polyaniline matrix and well-defined mesopores, is fabricated by employing a novel one-step approach. The as-prepared mesoporous polyaniline/anatase TiO₂ nanocomposite has a high specific surface area of 224 m² g⁻¹ and a predominant pore size of 3.6 nm. The electrochemical performance of the as-prepared composite as anode material is investigated by cyclic voltammograms and galvanostatic method. The results demonstrate that the polyaniline/anatase nanocomposite provides larger initial discharge capacity of 233 mAh g⁻¹ and good cycle stability at the high current density of 2000 mA g⁻¹. After 70th cycles, the discharge capacity is maintained at 140 mAh g⁻¹. The excellent electrochemical performance of the polyaniline/TiO₂ nanocomposite is mainly attributed to its special structure. Furthermore, it is accessible to extend the novel strategy to other polymer/TiO₂ composites, and the mesoporous polypyrrole/anatase TiO₂ is also successfully fabricated.     

Effect of pre-nitridation treatment on the formation of anatase TiO2 films by anodization

High performance-anatase TiO₂ films were successfully formed on metallic titanium by anodization in an acidic electrolyte composed of H₂SO₄, H₃PO₄ and H₂O₂ subsequent to pre-nitridation treatment. The pre-nitridation treatment was carried out by pre-annealing metallic titanium under a nitrogen atmosphere of 0.1 MPa. The anodized films showed photocatalytic activity in photooxidization of the iodide anion into the tri-iodide anion. The nitridation treatment had a significant effect not only on the formation of anatase TiO₂ films but also on the photocatalytic activity of the anodized films.     

Photocatalytic functional coatings of TiO2 thin films on polymer substrate by plasma enhanced atomic layer deposition

We prepared photocatalytic TiO₂ thin films which exhibited relatively high growth rate and low impurity on polymer substrate by plasma enhanced atomic layer deposition (PE-ALD) from Ti(NMe₂)₄ [tetrakis (dimethylamido) Ti, TDMAT] and O₂ plasma to show the self-cleaning effect. The TiO₂ thin films with anatase phase and bandgap energy about 3.3 eV were deposited at growth temperature of 250 °C and the photocatalytic effects were compared with commercial Activ glass. From contact angles measurement of water droplet and photo-induced degradation test of organic liquid, TiO₂ thin films with anatase phases showed superhydrophilic phenomena and decomposed organic liquid after UV irradiation. The anatase TiO₂ thin film on polymer substrate showed highest photocatalytic efficiency after 5 h UV irradiation. We attribute the highest photocatalytic efficiency of TiO₂ thin film with anatase structure to the formation of suitable crystalline phase and large surface area.     

Deposition of thin TiO2 layers on platinum by means of cyclic voltammetry of selected complex Ti(IV) media leading to anatase

Thin layers of anatase TiO₂, up to 1 μm, were produced on the surface of a platinum electrode by means of cycling voltammetry from the aqueous solutions of the peroxo-oxalate complexes and the oxalate complexes of titanium(IV). Mechanisms of TiO₂ electrodeposition as well as different electrochemical reactions causing pH changes at the electrode were studied. The electroreduction processes of hydrogen peroxide and nitrite ion on platinum cause the highest pH changes. Values of the molar ratio of Ti(IV)/H₂O₂ should be kept closely to 0.5.In all cases studied, the electrodeposition led to the partially decomposed amorphous oxalate compounds of titanium(IV), which can be converted into crystalline anatase above 500 °C in air. The thermal behaviour of TiO₂ precursor compounds was examined by DRIFTS and TG-DTA methods. Strong effects of K⁺ and NH₄⁺ ions on the electrodeposition process were found by using of the EQCM technique, Raman spectroscopy and XRD measurements. The ammonium electrolyte warrants purity of the anatase phase.Morphology of the oxide films produced in different solvents was examined by SEM.     

Photocatalytic oxidation of toluene to benzaldehyde over anatase TiO2 hollow spheres with exposed {001} facets

A new series of anatase TiO₂ hollow structures were prepared by a facile hydrothermal process. When the hydrothermal time was increased from 20 min to 72 h, the resulting TiO₂ solid spheres gradually transformed into TiO₂ hollow spheres with higher surface crystallinity and exposed {001} facets. The as-prepared TiO₂-72 h sample exhibited the highest activity comparing to other TiO₂-based samples and commercial product Degussa P-25 towards the selective photocatalytic oxidation of toluene to benzaldehyde. Such great photocatalytic performance was mainly attributed to enhanced UV-adsorption and better charge separation efficiency due to higher surface crystallinity of TiO₂-72 h.     

Development and study of anodic Ti/TiO2 electrodes and their potential use as impedimetric immunosensors

Titanium dioxide films were anodically formed at various potentials up to 65 V in 1 M H₂SO₄. Oxide films were characterized by performing various techniques, including electrochemical impedance spectroscopy, scanning electron microscopy, Raman spectroscopy, ellipsometry and diffuse reflectance FT-IR spectroscopy. Low voltage anodization (up to 10 V) results to amorphous TiO₂, whereas at higher applied potentials (up to 65 V), anatase is the predominant form. Anatase films were further hydroxylated with an acidic agent and the effect of this treatment on the overall impedance of the electrodes was studied with impedance spectroscopy. The potential use of anodic (anatase) Ti/TiO₂ electrodes in the development of impedimetric immunosensors is also demonstrated by monitoring the immunoreaction of avidin/anti-avidin with different instrumental approaches based on a FRA analyzer, an LCR-meter and a home-built charge integrator (Multipulser).     

Facile synthesis of mesoporous Ag-loaded TiO2 thin film and its photocatalytic properties

Ag nanoparticles highly dispersed into TiO₂ thin films are synthesized via a remarkably simple one-pot route in the presence of a P123 triblock copolymer as template directing and reducing agents, where the reduction of Ag⁺ to Ag⁰ by in situ heat-induced reduction through the oxidation of template at 400 °C and the controlled polymerization of TiO₂ take place simultaneously. The obtained mesoporous Ag/TiO₂ films deposited on soda-lime glass were optically transparent and crack-free. SEM and Kr adsorption clearly prove that Ag/TiO₂ films at different Ag contents are mesoporous with large surface area and regularly ordered mesopores and the thickness of the obtained films is ∼280 ± 20 nm. The pristine TiO₂ film exhibits a specific surface area of 63 cm²/cm² and specific pore volume of 0.013 mm³/cm² that it is decreased to 42 cm²/cm² and 0.010 mm³/cm² respectively as a result of Ag-loaded mesoporous TiO₂. The newly prepared photocatalysts Ag/TiO₂ films were evaluated for their photocatalytic degradation of 2-chlorophenol as a model reaction. It was found that the meso-ordered Ag/TiO₂ films are more photoactive 8 times than nonporous commercial photocatalysts Pilkington Glass Activ™. The recycling tests indicated that Ag/TiO₂ films was quite stable during that liquid-solid heterogeneous photocatalysis since no significant decrease in activity was observed even after being used repetitively for 10 times, showing a good potential in practical application. In general, the cubic mesoporous Ag/TiO₂ nanocomposites are stable and can be recycled without loss of their photochemical activity.     

Anatase TiO2 spheres with high surface area and mesoporous structure via a hydrothermal process for dye-sensitized solar cells

Spherical pure anatase TiO₂ spheres with a mesoporous structure and high surface area of up to 116.5 m² g⁻¹ were prepared by a simple urea-assisted hydrothermal process and investigated as dye-sensitized solar-cell electrodes. Although the particle diameters of the prepared TiO₂ spheres ranged from 0.4 to 1.3 μm, due to the high specific surface area, mesoporous TiO₂ sphere electrode was obtained with enhanced light harvesting and a larger amount of dye loading. An overall light conversion efficiency of 7.54% under illumination of simulated AM 1.5G solar light (100 mW cm⁻²) was achieved using the mesoporous TiO₂ spheres electrode, which was significantly higher than a commercial Degussa P25 TiO₂ nanocrystals electrode (5.69%).     

Onset coarsening-coalescence kinetics of ZrO2 and less refractory TiO2 nanoparticles: Effect of homologous temperature and phase transformation

Specific surface area change of ZrO₂ (predominant tetragonal - (t) symmetry, 30-50 nm) and less refractory TiO₂ anatase nanoparticles (20-50 nm) upon isothermal firing at 700-1000 °C in air was determined by N₂ adsorption-desorption hysteresis isotherm. The nanoparticles underwent onset coarsening-coalescence within minutes without appreciable phase transformation for TiO₂, but with extensive transformation into monoclinic (m-) symmetry for ZrO₂. The apparent activation energy of such a process being not much higher for ZrO₂ (77 ± 23 kJ/mol) than TiO₂ (56 ± 3 kJ/mol) nanoparticles can be attributed to transformation plasticity. The minimum temperature for coarsening/coalescence of the present ZrO₂ and TiO₂ nanoparticles was estimated as 710 and 641 °C, respectively.     

Properties of sol-gel SnO2/TiO2 electrodes and their photoelectrocatalytic activities under UV and visible light illumination

A visible light active binary SnO₂-TiO₂ composite was successfully prepared by a sol-gel method and deposited on Ti sheet as a photoanode to degrade orange II dye. Titanium and SnO₂ can promote the development of rutile phase of TiO₂ and inhibit the formation of anatase phase of TiO₂. Formation of SnO₂ crystalline is insignificant even when the calcination temperature increases to 700 °C. Heterogenized interface between SnO₂ and TiO₂ inhibits growth of TiO₂ linkage and leads to the particle-filled surface morphology of SnO₂-containing films. The carbonaceous, Ti-O-C bonds and Ti³⁺ species are likely to account for the photoabsorption and photoelectrocatalytic (PEC) activity under visible light illumination. The electrode with 30% SnO₂ exhibits higher photocurrent when compared with those in the region of 0-50%. The 600 °C-calcined SnO₂-TiO₂ electrode indicates higher activity when compared with those at 400, 500, 700 and 800 °C. PEC degradation of orange II follows the Langmuir-Hinshelwood model and takes place much effectively in a solution of pH 3.0 than those in pH 7.0 and pH 11.0.     

Tailoring high-surface-area nanocrystalline TiO2 polymorphs for high-power Li ion battery electrodes

The crystallization and morphology of brookite and anatase titania (TiO₂) were controlled using the urea-mediated hydrolysis/precipitation route in the presence of the Ti³⁺ ions. Without the strong complexing agents and the non-hydrothermal conditions, simple alterations to the urea concentration led to the synthesis from brookite nanorods to anatase nanoflowers at a low temperature below 100 °C, whereas the BET specific surface area evolved from 102 to 268 m² g⁻¹, respectively. A possible formation mechanism was also proposed for these TiO₂ nanostructures. The excellent reversible capacity and rate capability were achieved for the anatase nanoflowers because of the small crystallite size and significantly large surface area.     

Effect of silica on the microstructure and photocatalytic properties of titania

A series of TiO₂/SiO₂ composite with different Ti/Si ratios were prepared by sol–gel technique. The samples were characterized by different analytical techniques such as XRD, FT-IR, BET and XPS. Grain size of anatase TiO₂ calculated using Scherrer's formula was found to be in the range of 2.1–8.7 nm, and the content of anatase phase in TiO₂ ranges from 45% to 40.1%. The photocatalytic properties on methyl orange (MO) solution were also studied. The degradation rate of the composite is much higher than that of the pure TiO₂ in the same conditions.     

Sonosynthesis of nanostructured TiO2 doped with transition metals having variable bandgap

Here is described a sonosynthesis method to produce nanostructured TiO₂ pure and doped (Al, C, Co, Fe and Rh). The synthesized TiO₂ is amorphous and is transformed to anatase, brookite or rutile by heat treatments at temperatures between 100 and 300 °C. Pure TiO₂ can be partially transformed to brookite between 100 and 300 °C. The band gap in all heat treated samples from 100–600 °C is relatively constant, 3.2 eV, except for those doped with Fe. This effect on the band gap is the results of a bi/tri-crystal (anatase:brookite:rutile) framework. Rhodium is the most effective dopant to narrow the band gap, the opposite effect is observed with C. In single phase frameworks the bandgap can be modified ranges from 2.38 to 4.10 eV depending on the dopant. TiO₂ lattices are rigid enough to promote an outwards diffusion of the dopants to the surface of the particles forming nanostructured precipitates. The precipitates develop a network of quantum-dots with sizes between 5 and 10 nm.     

Effects of rf-power and working pressure on formation of rutile phase in rf-sputtered TiO2 thin film

Thin TiO₂ films have been deposited on glass substrates by a radio-frequency (rf) magnetron sputtering technique. The films were coated under argon atmosphere at three different rf-powers: 80, 100 and 120 W, and three working pressures: 1.0 × 10⁻², 2.5 × 10⁻³ and 1.0 × 10⁻³ mbar. Film structures were analyzed with XRD. At 100 and 120 W, films coated under low working pressure have developed the rutile phase with the preferred (1 1 0) orientation. However, at 80 W, the films have been observed only in an amorphous phase for all working pressures. This effect could be understood as sputtered TiO₂ molecules were more energetic at high rf-powers and encountered fewer collisions at low pressure before deposited onto the substrates. The films have also been annealed at 773 or 873 K. The post-deposition annealing has significantly improved crystallization of the TiO₂ films. In this contribution, results on optical and wetting properties of these films are also reported.