Synthesis of La2NiO4 via a PVA-based route

Single-phase La₂NiO₄ has been prepared using polyvinyl alcohol (PVA) as a complexing agent. Thermogravimetric (TG), Fourier transform infrared spectroscopy (FT-IR) and X-ray diffraction (XRD) were used to characterize precursor and derived oxide powders. The particle size and morphologies of La₂NiO₄ crystallites were characterized by field emission scanning electron microscope (FSEM). The effect of the mol ratios of metal ion to hydroxyl groups in polyvinyl alcohol on the formation of La₂NiO₄ was investigated. XRD analysis showed that single-phase and well-crystallized La₂NiO₄ was obtained from precursor with M/OH = 1:3 at 900 °C. The La₂NiO₄ ceramics sintered at 1300 °C for 4 h exhibits an electrical conductivity of 42.5 Ω⁻¹ cm⁻¹ at room temperature.     

Experimental determination of the eutectic temperature in air of the CuO-TiO2 pseudobinary system

Eutectic temperature and composition in the CuO-TiO₂ pseudobinary system have been experimentally determined in air by means differential thermal analysis (DTA), thermogravimetry (TG) and hot-stage microscopy (HSM). Samples of the new eutectic composition treated at different temperatures have been characterized by X-ray diffraction (XRD) and X-ray absorption near-edge structural spectroscopy (XANES) to identify phases and to determine the Cu valence state, respectively. The results show that the eutectic temperature in air is higher by 100 °C (∼1000 °C) for a Ti-richer composition (XTiO₂=25 mol%) than the one calculated in the literature. The reduction of Cu²⁺ to Cu⁺ takes places at about 1030 °C. The existence of Cu₂TiO₃ and Cu₃TiO₄ has been confirmed by XRD in the temperature range between 1045 and 1200 °C.     

Synthesis and characterization of high-density non-spherical Li(Ni1/3Co1/3Mn1/3)O2 cathode material for lithium ion batteries by two-step drying method

Non-spherical Li(Ni_1/3Co_1/3Mn_1/3)O₂ powders have been synthesized using a two-step drying method with 5% excess LiOH at 800 °C for 20 h. The tap-density of the powder obtained is 2.95 g cm⁻³. This value is remarkably higher than that of the Li(Ni_1/3Co_1/3Mn_1/3)O₂ powders obtained by other methods, which range from 1.50 g cm⁻³ to 2.40 g cm⁻³. The precursor and Li(Ni_1/3Co_1/3Mn_1/3)O₂ are characterized by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and scanning electron microscope (SEM). XPS studies show that the predominant oxidation states of Ni, Co and Mn in the precursor are 2⁺, 3⁺ and 4⁺, respectively. XRD results show that the Li(Ni_1/3Co_1/3Mn_1/3)O₂ material obtained by the two-step drying method has a well-layered structure with a small amount of cation mixing. SEM confirms that the Li(Ni_1/3Co_1/3Mn_1/3)O₂ particles obtained by this method are uniform. The initial discharge capacity of 167 mAh g⁻¹ is obtained between 3 V and 4.3 V at a current of 0.2 C rate. The capacity of 159 mAh g⁻¹ is retained at the end of 30 charge-discharge cycle with a capacity retention of 95%.     

Phase structure and nano-domain in high performance of BaTiO3 piezoelectric ceramics

BaTiO₃ ceramics were prepared by conventional sintering technique with a special emphasis on the effects of sintering temperature (1100-1230 °C) on the crystalline structure and piezoelectric properties. XRD patterns indicated that the crystallographic structure changed from tetragonal phase to orthorhombic one with raising sintering temperature from 1160 °C to 1180 °C. Domains were shaped in a stripe and a herringbone in orthorhombic samples for BaTiO₃ ceramics. The domain width and domain density increased with raising sintering temperature. The BaTiO₃ ceramic sintered at 1190 °C showed the excellent electrical properties, d₃₃ = 355 pC/N, k_p = 40%, P_r = 10.2 μC/cm², respectively, which are originated to the contributions of both the crystallographic structure transition and nano-domain.     

Synthesis of lanthanum beta-alumina powders by the polymeric precursor technique

La-β-Al₂O₃ (LaAl₁₁O₁₈) powders were synthesized by the polymeric precursor technique using lanthanum nitrate and aluminum nitrate. The transformations during thermal treatment of the precursor solution with ethylene glycol and citric acid were evaluated by thermal analysis. Fourier transform infrared spectroscopy analysis was performed after calcinations of the polymeric resin for determination of residual carbon. The specific surface area was evaluated by the BET method. Fine powders with ∼121 m²/g specific surface area and 20 nm average particle size were obtained and observed by scanning and transmission electron microscopy. Nearly single phase LaAl₁₁O₁₈ was obtained after pressing and sintering these powders at 1600 °C with small additions of MgO. The sintered pellets were characterized by X-ray diffraction and scanning electron microscopy. Impedance spectroscopy measurements carried out in the 1000–1200 °C range show the electrolytic behavior of the La-β-Al₂O₃ pellets, suggesting their application as solid electrolytes in high temperature potentiometric oxygen sensors.     

Spray-drying synthesized lithium-excess Li4+xTi5−xO12−δ and its electrochemical property as negative electrode material for Li-ion batteries

Li₄Ti₅O₁₂ (Fd-3m space group) materials were synthesized by controlling the lithium and titanium ratios (Li/Ti) in the range of 0.800-0.900 by using a spray-drying method, followed by calcination at several temperatures between 700 and 900 °C for large-scale production. Chemical and structure studies of the final products were done by X-ray diffraction (XRD), neutron diffraction (ND), X-ray photon electron spectroscopy (XPS), scanning electron microscopy (SEM) and inductively coupled plasma mass spectrometry (ICP-MS). The optimum synthesis condition was examined in relation to the electrochemical characteristics including charge-discharge cycling and ac impedance spectroscopy. It was found that when the spray-drying precursors at the Li/Ti ratio of 0.860 were calcined at 700-900 °C for 12 h in air, a pure Li_4+xTi_5−xO_12−δ (x = 0.06-0.08) phase with a lithium-excess composition was obtained. Based on the structural studies, it was found that the excess lithium is located at the lithium and titanium layer of the 16d site in the spinel structure (Fd-3m). These pure Li_4+xTi_5−xO_12−δ (x = 0.06-0.08) phase materials showed a higher discharge capacity of ∼164 mAh g⁻¹ at 1.55 V (vs. Li/Li⁺), between the cut-off voltage of 1.2-3.0, with an excellent cyclability and superior rate performance in comparison with the Li₄Ti₅O₁₂ phase containing impurity phases.     

Synthesis and characterization of nano-crystalline strontium hexaferrite using the co-precipitation and microemulsion methods with nitrate precursors

Nano-crystalline strontium hexaferrite (SrFe₁₂O₁₉) powder was synthesized using the classical co-precipitation and microemulsion methods. The precursors were obtained by precipitating Sr²⁺ and Fe²⁺ ions using tetramethylammonium hydroxide and calcinating at different temperatures ranging from 400 °C to 1000 °C in air. The influence of the Sr²⁺/Fe³⁺ mol ratio and the calcination temperature on the product formation and magnetic properties were studied. The formation of nanosized particles of SrFe₁₂O₁₉ with a relatively high saturation magnetization M_s = 64 Am²/kg, remanent magnetization of M_r = 39 Am²/kg and a coercitivity of H_c = 5.5 kOe was achieved at a Sr²⁺/Fe³⁺ mol ratio of 1:8 calcined at 900 °C. The formation of the SrFe₁₂O₁₉ was inspected using XRD analysis, thermogravimetric analysis (TGA), differential thermal analysis (DTA), TEM, and magnetic measurements.     

High thermally stable Mg-substituted tricalcium phosphate via precipitation

Tricalcium phosphates incorporating small amounts of Mg show attractive biological performances in terms of enhanced bone apposition, bone in-growth and cell-mediated degradation. A systematic investigation on Mg-stabilized β-TCP (β-tricalcium phosphate, β-Ca₃(PO₄)₂) is presented. Microstructure, composition and thermal behaviour were investigated by means of thermogravimetry and differential thermal analysis (TG-DTA), induced coupled plasma-atomic emission spectroscopy (ICP-AES), Fourier transform infrared spectroscopy (FT-IR), N₂ adsorption isotherms, X-ray diffraction (XRD and HT-XRD), and scanning electron microscopy (SEM). Pure and Mg-substituted tricalcium phosphate precursors consisted of calcium-deficient hydroxyapatite, the specific surface area being 128 m²/g and 87 m²/g, respectively. Tricalcium phosphate nanostructured powders were obtained by thermal treatment above 800 °C. The incorporation of Mg within the calcium phosphate lattice promoted the formation of the β-TCP phase at slightly lower temperature and resulted in the stabilization of the β-polymorph at high temperature (i.e. 1600 °C).     

Investigation of the intra-particle sintering kinetics of a mainly agglomerated alumina powder by using surface area reduction

An alumina precursor was prepared by the aluminium sulphate (0.20 M) and excess urea reaction in boiling aqueous solution. The precursor was calcined at 900 °C for 2 h and then δ-Al₂O₃ powder having volumetric agglomeration degree of 80% was obtained. Cylindrical compacts having diameter of 14 mm were prepared under 32 MPa by axial pressing using oleic acid as binder. Each compact was fired isothermally at various temperatures between 950 and 1400 °C. The firing time was changed from zero to 2 h. The fired compacts were examined by scanning electron microscopy (SEM) and nitrogen adsorption techniques. The specific surface areas (S/m² g^− 1) of the samples were calculated using the Brunauer, Emmett, and Teller (BET) procedure. The rate constant (k) and mechanism-characteristic parameter (n) were obtained for different temperatures between 950 °C and 1150 °C from the application of the neck-growth sintering rate (NGRM) model on the surface area reduction data. An Arrhenius equation and the parameter n for the sintering were found in the forms of k = (7.648 × 10⁶ h^− 1) exp (− 186,234 J mol^− 1 / RT) and n = 4.0 × 10^− 7 T³-1.7 × 10^− 3 T² + 2.3 T − 1030.8 respectively. The parameter n changes in the interval 0.61 <  n < 1.34 with rising temperature having maximum at about 1025 °C. Based on the SEM images and NGRM data, the intra-particle sintering was discussed.     

A simple and efficient preparation of LaFeO3 nanopowders by glycine-nitrate process: Effect of glycine concentration

LaFeO₃ perovskites have been prepared by the glycine-nitrate process (GNP) at various glycine-to-nitrate molar ratios. The perovskites have been systematically characterized by X-ray diffraction, BET surface area, scanning electron microscopy, transmission electron microscopy and temperature-programmed reduction to study the effect of glycine concentration on various properties of LaFeO₃. The X-ray diffraction patterns of the as-prepared and calcined samples show the formation of orthorhombic phase without any impurities. The BET specific surface areas of various perovskites increased with an increase in glycine-to-nitrate ratio (GNR) of 2.0 but were nearly constant at higher ratios. The scanning electron microscopy indicates that the prepared material is flake-like at GNRs ≤1.5 and exists as agglomerated particles at GNRs ≥2.0. The particle size of the as-prepared samples was in the range of 30-130 nm depending on the GNR and the calcined samples exhibited particle size in the range of 60-160 nm. The samples that were prepared at GNR < 1.5 did not show any peaks in temperature-programmed reduction, but the samples prepared at a GNR of 2.0 and above showed the reduction of Feⁿ⁺.     

Development of metal oxide nanoparticles by soft chemical method

An extensive work for the study of SnO₂ samples doped with x-mol% of Sb (x = 0, 6, 10, 14 and 18) is reported. The materials were prepared by the polymeric precursor method (Pechini method), calcined for 4 h between 800 °C and 1200 °C. The Rietveld method with X-ray diffraction data (XRD) was used to analyze the unit cell dimensions, crystallite size and microstrain. It was observed the crystallite size increasing and decrease of the microstrain with the increase of the calcining temperature. The synthesis of tin oxide nanoparticles with high thermal stability against particle growth rate was achieved by doping SnO₂ particles with Sb₂O₃. All the phases tend to have the same dimension when the temperature increases, although its values varies with x and reaches the maximum value when fired at 1100 °C. These variations seem to be an indication that the oxidation state of the antimony changes with the amount of Sb added to the material.     

Microstructure and ionic conductivity properties of gadolinia doped ceria (GdxCe1−xO2−x/2) electrolytes for intermediate temperature SOFCs prepared by the polyol method

Gd_0.1Ce_0.9O_1.95 and Gd_0.2Ce_0.8O_1.9 powders were prepared through the polyol process without using any protective agent. Microstructural and physical properties of the samples were characterized with X-ray diffraction (XRD), scanning electron microscopy (SEM), thermogravimetry (TG) and impedance analysis methods. The results of the thermogravimetry/differential thermal analysis (TG/DTA) and XRD indicated that a single-phase fluorite structure formed at the relatively low calcination temperature of 500 °C. The XRD patterns of the samples revealed that the crystallite size of the samples increased as calcination temperatures increased. The sintering behavior and ionic conductivity of pellets prepared from gadolinia doped ceria (GDC) powders, which were calcined at 500 °C, were also investigated. The relative densities of the pellets, which were sintered at temperatures above 1300 °C, were higher than 95%. The results of the impedance spectroscopy revealed that the GDC-20 sample that was sintered at 1400 °C exhibited an ionic conductivity of 3.25×10⁻² S cm⁻¹ at 800 °C in air. This result clearly indicates that GDC powder with adequate ionic conductivity can be prepared through the polyol process at low temperatures.     

Synthesis of nanocrystalline ytterbium-doped yttria by citrate-gel combustion method and fabrication of ceramic materials

Nanosized ytterbium doped yttria powders were prepared by citrate-gel combustion techniques. As-synthesized precursor and calcined powders were characterized for their crystalline structure, particle size and morphologies. Nanocrystalline Yb³⁺:Y₂O₃ powders with pure cubic yttria crystal structure were obtained by calcination of as-prepared precursors at 1100 °C for 3 h. Powders obtained were well dispersed with an average particle size of 60 nm. By using the obtained powders, nearly full dense Yb³⁺:Y₂O₃ ceramics were produced by vacuum sintering at 1800 °C for 12 h. The emission spectrum of the sintered ceramics under the excitation wavelength of 905 nm illustrates that there are three fluorescence peaks locating at 976 nm, 1030 nm and 1075 nm respectively, all corresponding to the ²F_5/2 → ²F_7/2 transitions of ytterbium ion.     

Preparation of nanocrystalline Sr3Al2O6 powders via citric acid precursor

Sr₃Al₂O₆ was synthesized via citric acid precursor. The effects of the molar ratio of citric acid to total metal cations concentration (CA/M) on the formation of Sr₃Al₂O₆ were investigated. Increasing the CA/M promoted the formation of Sr₃Al₂O₆. Single-phase and well-crystallized Sr₃Al₂O₆ was obtained from the CA/M = 1, CA/M = 2 and CA/M = 4 precursor at temperature 1200 °C, 1100 °C and 900 °C, respectively. Differential thermal analysis and thermogravimetric (DTA/TG), X-ray diffractometry (XRD) and field emission scanning electron microscopy (FESEM) were used to characterize the precursors and the derived oxide powders. Sr₃Al₂O₆ nanoparticles with a diameter of about 50-70 nm were obtained.     

Titanium dioxide modified with transition metals and rare earth elements: Phase composition,optical properties,and photocatalytic activity

A series of titania–transition metal and titania–rare earth element mixtures, with the stoichiometry Ti_1−xM_xO₂, where M=Ce, Eu, La, Nb, W, Y, and x ranging from 0 to 0.05 atoms per formula unit, were prepared via solid-state reaction of the precursor oxides. The products of the synthesis were thermally treated in air and two maximum temperatures (900 and 1000 °C) were reached.     

Synthesis of nanocrystalline lithium niobate powders via a fast chemical route

Lithnium niobate (LiNbO₃) can be obtained by mixing lithium nitrate (LiNO₃), ammonium niobate oxalate hydrate (C₄H₄NNbO₉) and glycine and then calcining at 600 °C for 1 h. The thermal analysis, structure, and morphology of the as-prepared LiNbO₃ were characterized by thermogravimetric and differential thermal analyses (TG/DTA), powder X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The crystallization temperature of LiNbO₃ precursor is 580 °C based on the TG/DTA results. After being calcined at 600 °C, the structure of the LiNbO₃ synthesized using various ratios of glycine to metal nitrates (Ψ-value) was formed with a particle size of about 29-38 nm, as found by XRD analysis. The crystal size has the lowest value at Ψ = 2, and the highest level of crystallization is at Ψ = 3.     

Structural and electrochemical behaviors of metastable Li2/3[Ni1/3Mn2/3]O2 modified by metal element substitution

Layered metastable lithium manganese oxides, Li_2/3[Ni_1/3−xMn_2/3−yM_x+y]O₂ (x = y = 1/36 for M = Al, Co, and Fe and x = 2/36, y = 0 for M = Mg) were prepared by the ion exchange of Li for Na in P2-Na_2/3[Ni_1/3−xMn_2/3−yM_x+y]O₂ precursors. The Al and Co doping produced the T^#2 structure with the space group Cmca. On the other hand, the Fe and Mg doped samples had the O6 structure with space group R-3m. Electron diffraction revealed the 1:2 type ordering within the Ni_1/3−xMn_2/3−yM_x+yO₂ slab. It was found that the stacking sequence and electrochemical performance of the Li cells containing T^#2-Li_2/3[Ni_1/3Mn_2/3]O₂ were affected by the doping with small amounts of Al, Co, Fe, and Mg. The discharge capacity of the Al doped sample was around 200 mAh g⁻¹ in the voltage range between 2.0 and 4.7 V at the current density of 14.4 mA g⁻¹ along with a good capacity retention. Moreover, for the Al and Co doped and undoped oxides, the irreversible phase transition of the T^#2 into the O2 structure was observed during the initial lithium deintercalation.     

Electrochemical performance of the carbon coated Li3V2(PO4)3 cathode material synthesized by a sol-gel method

A carbon coated Li₃V₂(PO₄)₃ cathode material for lithium ion batteries was synthesized by a sol-gel method using V₂O₅, H₂O₂, NH₄H₂PO₄, LiOH and citric acid as starting materials, and its physicochemical properties were investigated using X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) spectroscopy, scanning electron microscopy (SEM), energy dispersive analysis of X-ray (EDAX), transmission electron microscope (TEM), and electrochemical methods. The sample prepared displays a monoclinic structure with a space group of P2₁/n, and its surface is covered with a rough and porous carbon layer. In the voltage range of 3.0-4.3 V, the Li₃V₂(PO₄)₃ electrode displays a large reversible capacity, good rate capability and excellent cyclic stability at both 25 and 55 °C. The largest reversible capacity of 130 mAh g⁻¹ was obtained at 0.1C and 55 °C, nearly equivalent to the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹). It was found that the increase in total carbon content can improve the discharge performance of the Li₃V₂(PO₄)₃ electrode. In the voltage range of 3.0-4.8 V, the extraction and reinsertion of the third lithium ion in the carbon coated Li₃V₂(PO₄)₃ host are almost reversible, exhibiting a reversible capacity of 177 mAh g⁻¹ and good cyclic performance. The reasons for the excellent electrochemical performance of the carbon coated Li₃V₂(PO₄)₃ cathode material were also discussed.     

Spray-drying synthesized LiNi0.6Co0.2Mn0.2O2 and its electrochemical performance as cathode materials for lithium ion batteries

Layered LiNi_0.6Co_0.2Mn_0.2O₂ materials were synthesized at different sintering temperatures using spray-drying precursor with molar ratio of Li/Me = 1.04 (Me = transition metals). The influences of sintering temperature on crystal structure, morphology and electrochemical performance of LiNi_0.6Co_0.2Mn_0.2O₂ materials have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and charge-discharge test. As a result, material synthesized at 850 °C has excellent electrochemical performance, delivering an initial discharge capacity of 173.1 mAh g^− 1 between 2.8 and 4.3 V at a current density of 16 mA g^− 1 and exhibiting good cycling performance.     

TPR,XRD and XPS characterisation of ceria-based materials synthesized by freeze-drying precursor method

A freeze-drying precursor method was used to obtain submicrometric powders of ceria-based materials such as Ce_1−xGd_xO_2−δ (x=0, 0.01, 0.05, 0.10 and 0.20), 80%CeO₂–20%ZrO₂, 80%CeO₂–20%Al₂O₃ and (1−y)Ce_0.99Gd_0.01O_2−δ– (y)Al₂O₃ (y=0.01, 0.02, 0.05, 0.10 and 0.30) at temperatures as low as 400 °C. The phase formation and evolution with the temperature was studied by X-ray diffraction (XRD). Also, temperature programmed reduction (TPR) was performed to investigate the reducibility of the ceramic powders. It was observed that after reduction of the ceria-based materials the fluorite structure of the samples was retained. The TPR profiles showed two peaks which are associated to the surface and bulk ceria reduction processes. Likewise, after the TPR measurements the resulting powders have showed high phase stability and reproducibility. XPS results confirmed the reduction of Ce⁴⁺ to (Ce³⁺+Ce⁴⁺) ratio with alumina doping.