Characterization of Ce0.9Gd0.1O1.95 powders synthesized by spray drying

Ce_0.9Gd_0.1O_1.95 powders were synthesized by spray drying and successive calcinations. The phase purity, BET surface area, and particle morphology of as-sprayed and calcined powders were characterized. After calcination above 300 °C, the powders were single phase and showed a BET surface area of 68 m²/g when calcined at 300 °C. The conductivity, in air, of sintered pellets was measured by electrochemical impedance spectroscopy (EIS) and it was found to be comparable with literature values. The activation energy for the total conductivity was around 0.83 eV. The powder calcined at lower temperature showed better sinterability and higher total conductivity due to an increased bulk conductivity.     

复合阳极Ni-Fe/Ce0.9Gd0.1O1.95在阴极支撑单电池的性能及其表征

为了提高固体氧化物燃料电池在中温条件下的电性能,探索了一种双金属阳极的阴极支撑单电池。单电池以La_0.6Sr_0.4CoO₃（LSC）-Ce_0.9Gd_0.1O_1.95（GDC）为阴极支撑体,旋涂了甘氨酸-硝酸盐法制备的La_0.9Sr_0.1Ga_0.8Mg_0.2O_3-δ（LSGM）电解质及Sm_0.2Ce_0.8O_1.9（SDC）缓冲层,涂覆了由硬模板法和浸渍法结合制备的Ni-Fe/GDC双金属阳极。对制备材料进行了XRD和微观形貌分析,单电池电化学测试在800 ℃和750 ℃下,以氢气为燃料的最大功率密度达0.73 W/cm²和0.64 W/cm²,以甲烷为燃料时达0.41 W/cm²和0.40 W/cm²。测试后的SEM表明,阳极具有多孔的微观结构,金属颗粒均匀包覆蠕虫状GDC,保证了单电池具有较高的发电性能。     

甘油水蒸汽重整制氢Ni/Ce0.9Gd0.1O1.95催化剂的研究

采用浸渍法和共沉淀法制备了Ni质量分数10%的10%Ni/Ce_0.9Gd_0.1O_1.95催化剂,通过X射线衍射、N₂物理吸附与H₂脉冲化学吸附、H₂程序升温还原等技术表征了催化剂的结构和性质,并考察了其催化甘油水蒸汽重整制氢反应性能。结果表明,浸渍法制备的10%Ni/Ce_0.9Gd_0.1O_1.95-S催化剂的活性最佳,该催化剂上Ni晶粒小、分散度高,形成氧空穴使得催化剂抗积炭能力大大提高,所以活性、氢气选择性较高,稳定性也较好。同时考察了水与甘油物质的量比和泵流速对甘油重整反应性能的影响,发现在水与甘油物质的量比为24:1,泵流速为0.06 mL·min^-1的条件下,甘油几乎完全转化,氢气选择性也非常高,而且反应10 h没有失活。     

Synthesis of nano-crystalline Ce0.9Gd0.1O1.95 electrolyte by novel sol–gel thermolysis process for IT-SOFCs

In the present work, nano-crystalline Ce_0.9Gd_0.1O_1.95 (GDC) powder has been successfully prepared by a novel sol–gel thermolysis method using a unique combination of urea and PVA. The gel precursor obtained during the process was calcined at 400 and 600 °C for 2 h. A range of analyzing techniques including XRD, TGA, BET, SEM, EDS and TEM were employed to characterize the physical and chemical properties of obtained powders. GDC gel precursors calcined at 400 and 600 °C were found to have an average crystallite size of 10 and 19 nm, respectively. From the result of XRD patterns, we found that well-crystalline cubic fluorite structure GDC was obtained by calcining the precursor gel at 400 and 600 °C. It has been also found that the sintered samples with lower temperature calcined powder showed better sinterability as well as higher ionic conductivity of 2.21 × 10⁻² S cm⁻¹ at 700 °C in air.     

A comparative study of NiO-Ce0.9Gd0.1O1.95 nanocomposite powders synthesized by hydroxide and oxalate co-precipitation methods

In this study, NiO-Ce_0.9Gd_0.1O_1.95 (NiO-GDC) nanocomposite powders, which were applied as anode materials of low temperature solid oxide fuel cells (SOFCs), were synthesized by hydroxide and oxalate reverse co-precipitation methods, respectively. The crystal phases, crystallite size, particle size, particle size distribution, and sintering characteristics of the synthesized NiO-GDC nanocomposite powders were investigated and compared. Results showed that the different co-precipitation methods affected strongly the synthesis and characteristics of the NiO-GDC nanocomposite powders. The NiO-GDC nanocomposite powders could be synthesized at lower temperature by the hydroxide reverse co-precipitation method, and the synthesized NiO-GDC nanocomposite powders had better sinterability. The NiO-GDC nanocomposite powders synthesized by the oxalate reverse co-precipitation method had smaller particle size and uniform particle size distribution and, however, were easy to result in crack formation in the sintered disks.     

Synthesis of spherical LiMn2O4 microparticles by a combination of spray pyrolysis and drying method

Lithium manganese oxide (LiMn₂O₄) has been synthesized by a spray pyrolysis method from the precursor solution; LiNO₃ and Mn(NO₃)₂·6H₂O were stoichiometrically dissolved into distilled water. The synthesized LiMn₂O₄ particles exhibited a pure cubic spinel structure in the X-ray diffraction (XRD) patterns, however they were spherical hollow spheres for various concentrations of precursor solution. Thus, the as-prepared LiMn₂O₄ particles were then ground in a mortar and dispersed into distilled water. To make a well dispersed slurry solution, a dispersion agent was also added into the slurry solution. The LiMn₂O₄ microparticles with a spherical nanostructure were finally prepared by a spray drying method from the slurry solution. The tap density of the LiMn₂O₄ microparticle prepared by a combination of spray pyrolysis and drying method was larger than that by a conventional spray pyrolysis method.The as-prepared samples were sintered at 750 °C for 1 h in air and used as cathode active materials for lithium batteries. Test experiments in the electrochemical cell Li|1 M LiClO₄ in EC:DEC = 1:1|LiMn₂O₄ demonstrate that the sample prepared by the present method is a promising cathode active material for 4 V lithium-ion batteries at high-charge-discharge and elevated temperature operation. The LiMn₂O₄ compounds by the combination of spray pyrolysis and drying method are superior to that by the conventional spray pyrolysis method in terms of electrochemical characteristics and tap density.     

Fabrication of dense Ce0.9Mg0.1P2O7-PmOn composites by microwave heating for application as electrolyte in intermediate-temperature fuel cells

In the present work, we report a method of fabrication of dense 10 mol% Mg²⁺-doped cerium pyrophosphate-phosphate (Ce_0.9Mg_0.1P₂O₇-P_mO_n; CMP-P) composites by microwave heat-treatment of the preformed Ce_0.9Mg_0.1P₂O₇ substrates in the presence of phosphoric acid. The composite was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS). The microwave heating at 375 °C for 5 min resulted in the formation of dense CMP-P composites which retained most of the pyrophosphate phase. The electrical conductivity was extracted from the EIS data and for the CMP-P composite prepared by H₃PO₄ loading for 10 h and microwave heat-treatment for 5 min it was found to be >10^?2 S m^?1 in 100–250 °C range with a maximum of 0.062 S cm^?1 at 190 °C, which was significant for its application as electrolyte in intermediate temperature fuel cells.     

Electrochemical characteristics of LiNi0.5Mn1.5O4 prepared by spray drying and post-annealing

LiNi_0.5Mn_1.5O₄ was prepared by a spray drying and post-annealing process. The re-annealing treatment in O₂ could not only decrease the Mn³⁺ content, but also increased the reversible capacity and significantly improve the rate capability compared to the untreated material. Moreover, the cyclic performance of the LiNi_0.5Mn_1.5O₄ depends on both the cycling rate and operating temperature, which was ascribed to the difference between the phase transition rates between cubic I ↔ cubic II and cubic II ↔ cubic III.     

Selectivity of high surface area Ce0.68Zr0.32O2 for the new generation of TWC under environments with different redox character

A number of experiments were carried out with fresh and aged high surface area Ce_0.68Zr_0.32O₂ mixed oxide samples with complex feed-streams in order to determine their performance as three way catalyst (TWC). The results confirmed the oxygen storage capacity (OSC) of these samples, which favour NO conversion in cycled versus stationary stoichiometric operation. Several experiments carried out with different feed-streams have shown that a pre-reducing treatment can significantly improve both NO reduction at low-temperature and selectivity to N₂, which can be very useful to reduce the emission of nitrogen oxides immediately after starting the automobile. Although a significant reduction of the specific surface area of the mixed oxide takes place during ageing at 1173 K, it has been shown that the performance of the sample remains similar or even better than when fresh, due to an increased OSC. Thus, the reduction of CO and hydrocarbon emissions during start could be achieved by situating the catalytic converter nearer the exhaust to the engine, where the catalyst will be heated faster.     

A simple and effective process for fabrication of Gd0.1Ce0.9O1.95 solid electrolyte ceramics

Ce_0.9Gd_0.1O_1.95 ceramics were prepared using a simple and effective process in this study. Without any prior calcination, the mixture of raw materials was pressed and sintered directly. The reaction of the raw materials occurred during the heating up period by passing the calcination stage in the conventional solid-state reaction method. More than 99.5% of theoretical density was obtained for Ce_0.9Gd_0.1O_1.95 sintering at 1500–1600 °C. Fine grains (<1 μm) formed in pellets sintered at 1450 °C. The homogeneity of grains increased with the sintering temperature. The grains grew to >4.5 μm in pellets sintered at 1600 °C. The reactive-sintering process is proved to be a simple and effective method in preparing Ce_0.9Gd_0.1O_1.95 ceramics for solid electrolyte application.     

Nano-crystalline LiNi0.5Mn1.5O4 synthesized by emulsion drying method

LiNi_0.5Mn_1.5O₄ spinel has been prepared by an emulsion drying method which can intermix cations very homogeneously at the atomic scale. When the emulsion-dried precursor was fired at 750 °C for 24 h, the observed particle of the LiNi_0.5Mn_1.5O₄ was nano-crystallite, being about 50 nm in diameter. The Rietveld refinement result clearly exhibited that the cubic spinel phase was successfully formed without any secondary phases, indicating that Li and transition metal cations occupied the 8a and 16d sites of the Fd3m structure, respectively. Li deintercalation from the spinel framework brings about a shift in the XRD peak toward higher angles and a peak splitting in the composition range δ=0-0.2 in Li_δNi_0.5Mn_1.5O₄, implying that the host structure is progressively oxidized from Ni²⁺ to Ni⁴⁺ and accompanied by a two phase reaction. The sample calcined at 750 °C for 24 h showed the best cyclability upon cycling due probably to better crystallinity and a smaller particle size. We suggest that this material can be used as a 4.5 V cathode material for Li-ion battery.     

Mesoporous Ti2Nb10O29 microspheres constructed by interconnected nanoparticles as high performance anode material for lithium ion batteries

Mesoporous Ti₂Nb₁₀O₂₉ microspheres are prepared through a solvothermal method in isopropanol-glycerol solvent followed by calcination treatment. The Ti₂Nb₁₀O₂₉ microspheres with diameter in the range between 1.0 and 2.0?µm are assembled from nanoparticles. The special hierarchical mesoporous structure of Ti₂Nb₁₀O₂₉ microspheres can reduce the Li⁺ ions diffusion distance and supply large interfacial area between electrolyte and electrode, endowing them with better electrochemical properties compared to Ti₂Nb₁₀O₂₉ nanoparticles. At different current densities of 1, 5, 10, 20 and 30?C, the first discharge capacity of mesoporous microspheres is respectively 268.9, 218.5, 205.3, 180.5, and 158.1 mA?h g^?1. By contrast, the corresponding values of Ti₂Nb₁₀O₂₉ nanoparticles are quickly reduced from 254.6, 196.3, 159.4, 127.5, to 99.0 mA?h g^?1. It worth noting that Ti₂Nb₁₀O₂₉ microspheres exhibit excellent rate capacities. Furthermore, at a current density of 10?C, the specific capacity of Ti₂Nb₁₀O₂₉ microspheres can be maintained at 173.5 mA?h g^?1 after 500 cycles, with 86.8% retention of the first discharge capacity. These results suggest that the Ti₂Nb₁₀O₂₉ mesoporous microspheres would be developed as potential anodic materials for high performance lithium-ion batteries.     

Spray drying of TiO2 nanoparticles into redispersible granules

We have demonstrated how titania nanoparticles can be spray-dried to produce redispersible granules. The evaluation of different dispersants using rheology, particle size and electrokinetic measurements showed that an anionic carboxylated polyelectrolyte, Dispex N40, was able to stabilize the primary aggregates of the titania nanoparticles with a size of about 180 nm at an addition of 2.4% dry-weight basis over a relatively large pH-range. Transmission electron microscopy showed that the commercial P-25 titania nanopowder could not be deagglomerated down to the individual crystallite size of 15-40 nm. Spherical granules with a size between 20 and 50 μm and a minimum amount of dusty fines could be produced by spray drying the aqueous titania dispersions in a configuration with internal bag filters. The granules could be completely disintegrated and redispersed in water by ultrasonication into a stable suspension with a size distribution that is identical to the as-received powder. The possibility to prepare redispersible nanoparticle granules by spray drying is a route to minimize the risk of airborne exposure and facilitate the handling of nanopowders.     

Morphological and electrochemical properties of LiV3O8 cathode powders prepared by spray pyrolysis

Lithium trivanadate (LiV₃O₈) powders are prepared by spray pyrolysis. The precursor powders of LiV₃O₈ obtained by spray pyrolysis have spherical and rod-like morphologies. The LiV₃O₈ powders post-treated at 300 °C and 400 °C also have spherical and rod-like morphologies. However, the LiV₃O₈ cathode powders post-treated at 500 °C consist of only rod-like crystals. The crystalline structure of the precursor powders that were directly prepared by spray pyrolysis comprised of LiV₃O₈ layers along with a small amount of β-Li_0.33V₂O₅ impurity. The peak due to β-Li_0.33V₂O₅ persisted in the XRD spectrum even after post-treatment at 300 °C. On the other hand, crystalline structures of the powders post-treated at 400 °C and 500 °C comprised pure LiV₃O₈ layers. The initial discharge capacities of the LiV₃O₈ cathode powders decrease from 344 mAh g⁻¹ to 261 mAh g⁻¹ when the post-treatment temperatures increase from 300 °C to 500 °C. The discharge capacities of the LiV₃O₈ cathode powders obtained after post-treatment at 400 °C and 500 °C are approximately 255 mAh g⁻¹ and 236 mAh g⁻¹, respectively, after 40 cycles.     

Hydrothermal synthesis of LiNi0.9Co0.1O2 cathode materials

Ultrafine powders of LiNi_0.9Co_0.1O₂ were prepared under mild hydrothermal conditions. The product was characterized by XRD, TEM and EDS tests, which indicated that the obtained products were pure and well-crystallized LiNi_0.9Co_0.1O₂. The ICP-AES results indicated the products were lithium-deficient compounds. The addition of KOH hardly effected the crystallinity of the product but gave larger crystals.     

Yb2O3 and Y2O3 co-doped zirconia ceramics

A suspension stabilizer-coating technique was employed to prepare x mol% Yb₂O₃ (x = 1.0, 2.0, 3.0 and 4.0) and 1.0 mol% Y₂O₃ co-doped ZrO₂ powder. A systematic study was conducted on the sintering behaviour, phase assemblage, microstructural development and mechanical properties of Yb₂O₃ and Y₂O₃ co-doped zirconia ceramics. Fully dense ZrO₂ ceramics were obtained by means of pressureless sintering in air for 1 h at 1450 °C. The phase composition of the ceramics could be controlled by tuning the Yb₂O₃ content and the sintering parameters. Polycrystalline tetragonal ZrO₂ (TZP) and fully stabilised cubic ZrO₂ (FSZ) were achieved in the 1.0 mol% Y₂O₃ stabilised ceramic, co-doped with 1.0 mol% Yb₂O₃ and 4.0 mol% Yb₂O₃, respectively. The amount of stabilizer needed to form cubic ZrO₂ phase in the Yb₂O₃ and Y₂O₃ co-doped ZrO₂ ceramics was lower than that of single phase Y₂O₃-doped materials. The indentation fracture toughness could be tailored up to 8.5 MPa m^1/2 in combination with a hardness of 12 GPa by sintering a 1.0 mol% Yb₂O₃ and 1.0 mol% Y₂O₃ ceramic at 1450 °C for 1 h.     

Characterization of luminescent SrAl2O4 films doped with terbium and europium ions deposited by ultrasonic spray pyrolysis technique

SrAl₂O₄, SrAl₂O₄:Tb³⁺ and SrAl₂O₄:Eu³⁺:Eu²⁺ films were synthesized by means of the ultrasonic spray pyrolysis technique. These samples, characterized by X-Ray Diffraction, showed the monoclinic phase of the strontium aluminate. Images of the surface morphology of these films were obtained by SEM and the chemical composition was measured by EDS and XPS. The photoluminescence and cathodoluminescence characteristics of the films were studied as a function of the terbium and europium concentrations. The optimal PL emission intensities were reached at 8?at% for terbium doped films and 6?at% for europium doped samples. The CL emission spectra for europium doped films showed the typical bands of Eu³⁺ ions and also a broadband centered at 525?nm which is attributed to Eu²⁺ ions. XPS measurements confirm the presence of Eu³⁺ and Eu²⁺ in europium doped SrAl₂O₄ films, without having been subjected to a reducing atmosphere. Chromatic diagrams exhibited green color for SrAl₂O₄:Tb³⁺ films, red and yellow colors for SrAl₂O₄:Eu³⁺:Eu²⁺ films. The PL decay curves were also obtained: the averaged decay time was 2.7?ms for SrAl₂O₄:Tb³⁺ films and 1.9?ms for SrAl₂O₄:Eu³⁺ films. Similar results were obtained by the stretched exponential model.     

Mesoporous and nanostructured CeO2 as supports of nano-sized gold catalysts for low-temperature water-gas shift reaction

Mesoporous particles and 1D nanorods of cerium oxides have been prepared by modifying the hydrothermal route of a surfactant-assisted controllable synthesis. Mesoporous cerias were obtained in a sealed glass vessel under continuous stirring, while ceria nanorods were obtained in a Teflon-lined autoclave without stirring. The mesoporous cerias did not show long-range mesoscopic organization, exhibiting a broad mesopore size distribution in the region 8–15 nm. A BET surface area of 100 m²/g with a total pore volume of 0.33 cm³/g is obtained for as-synthesized mesoporous ceria. The ceria nanorods exhibit a cubic crystalline structure after calcination, having the lengths in the range of 150–300 nm and diameters in the range of 10–25 nm. The growth direction of ceria nanorods is along [1 1 0]. A surface area of above 50 m²/g is obtained in the calcined nanorods. These synthesized ceria materials were used as supports of nano-sized gold catalysts, prepared by deposition–precipitation method. Their catalytic activity was evaluated by the low-temperature water-gas shift reaction. The gold/mesoporous ceria catalytic system exhibited higher catalytic activity than gold/ceria nanorods. It is revealed that the mesoporous and nanostructured cerias are of much interest as potential supports for gold-based catalysts that are effective for low-temperature water-gas shift reaction.     

Synergistic effect in structural and supercapacitor performance of well dispersed CoFe2O4/Co3O4 nano-hetrostructures

Herein, we report a facile homogeneous urea – assisted hydrothermal approach for the design of CoFe₂O₄/Co₃O₄ nano hetrostructure. A variation in Co concentration leads to smartly designed composite material namely CFC-11 and CFC-12 where CFC-12 appreciates the benefits of both CoFe₂O₄ and Co₃O₄ nanoparticles. The physico – chemical properties of as developed materials were investigated by X-ray diffraction (XRD), field emission electron microscopy (FE-SEM), high resolution transmission electron microscopy (HR-TEM), X-ray photoelectron microscopy (XPS) and Raman spectroscopy. The specific surface area and pore size distribution was determined by Brunauer-Emmett-Teller (BET) and Barrett-Joyner-Halendo (BJH) respectively. Magnetic measurements via. vibrating sample magnetometer (VSM) demonstrate that saturation magnetization decreases with the incorporation of Co₃O₄ antiferromagnetic nanoparticles. To explore the utility of as designed nano-hetrostructures as supercapacitor electrodes, we employed cyclic voltammetry (CV) and electrochemical impedence spectroscopy (EIS) measurements. A high specific capacitance of 761.1?F?g^?1 at 10?mV?s^?1, admirable cyclic durability of 92.2% and a low resistance value obtained from impedence measurements was observed for CFC-12. The favorable performance demonstrates the synergistic effect of CoFe₂O₄ and Co₃O₄ nanoparticles and thus promise an excellent material for energy storage devices.     

Improving sintering behavior of MWCNT/BaTiO3 ceramic nanocomposite with Bi2O3-B2O3 addition

The present research systematically investigated the novel low-temperature fabrication of a multi-walled carbon nanotube (MWCNT)/barium titanate nanocomposite using a two-step mixing technique. The synthesis was conducted using different amounts of MWCNT (0.25%, 0.5%, 1%, 2%, 4%, and 8% wt) with different compositions of (Bi₂O₃ + B₂O₃) as a sintering aid. Scanning and transmission electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, three-point bending strength, Vickers hardness indentation and Archimedean technique were used to characterize the as-synthesized specimens. It was found that the appropriate content of sintering aid (Bi₂O₃+B₂O₃) strongly decreased the sintering temperature from 1200 °C to 950 °C. The results also revealed that any sintering aid with the optimum composition that included 30% (mol) Bi₂O₃ was optimal for a sintering aid content of 6% (wt). Consequently, the highest values of the flexural strength and fracture toughness were achieved by applying the optimal amounts of MWCNT (1% wt) and sintering aid (6% wt).