Synthesis and characterization of ZnxMg1 − xGa2O4:Co fabricated by low-temperature burning method

A series of Zn_xMg_1 − xGa₂O₄:Co²⁺ spinels (x = 0, 0.25, 0.5, 0.75, and 1.0) was successfully produced through low-temperature burning method by using Mg(NO₃)₂·4H₂O, Zn(NO₃)₂·6H₂O, Ga(NO₃)₃·6H₂O, CO(NH₂)₂, NH₄NO₃, and Co(NO₃)₂·6H₂O as raw materials. The product was characterized by X-ray diffraction, transmission electron microscopy, and photoluminescence spectroscopy. The product was not merely a simple mixture of MgGa₂O₄ and ZnGa₂O₄; rather, it formed a solid solution. The lattice constant of Zn_xMg_1 − xGa₂O₄:Co²⁺ (0 ≤ x ≤ 1.0) crystals has a good linear relationship with the doping density, x. The synthesized products have high crystallinities with neat arrays. Based on an analysis of the form and position of the emission spectrum, the strong emission peak around the visible region (670 nm) can be attributed to the energy level transition [⁴T₁(⁴P) → ⁴A₂(⁴F)] of Co²⁺ in the tetrahedron. The weak emission peak in the near-infrared region can be attributed to the energy level transition [⁴T₁(⁴P) → ⁴T₂(⁴F)] of Co²⁺ in the tetrahedron.     

Evolution of the local structure and electrochemical properties of spinel LiNixMn2−xO4 (0 ≤ x ≤ 0.5)

A series of Ni substituted spinel LiNi_xMn_2−xO₄ (0 ≤ x ≤ 0.5) have been synthesized to study the evolution of the local structure and their electrochemical properties. X-ray diffraction showed a few Ni cations moved to the 8a sites in heavily substituted LiNi_xMn_2−xO₄ (x ≥ 0.3). X-ray photoelectron spectroscopy confirmed Ni²⁺ cations were partially oxidized to Ni³⁺. The local structures of LiNi_xMn_2−xO₄ were studied by analyzing the and A_1g Raman bands. The most compact [Mn(Ni)O₆] octahedron with the highest bond energy of Mn(Ni)O was found for LiNi_0.2Mn_1.8O₄, which showed a Mn(Ni)O average bond length of 1.790 Å, and a force constant of 2.966 N cm⁻¹. Electrolyte decomposition during the electrochemical charging processes increased with Ni substitution. The discharge capacities at the 4.1 and 4.7 V plateaus obeyed the linear relationships with respect to the Ni substitution with the slopes of −1.9 and +1.9, which were smaller than the theoretical values of −2 and +2, respectively. The smaller slopes could be attributed to the electrochemical hysteresis and the presence of Ni³⁺ in the materials.     

Structural and magnetic characterization of MnxZn1 − xFe2O4 (x = 0.2; 0.35; 0.65; 0.8; 1.0) ferrites obtained by the citrate precursor method

In this work the microstructure and magnetic properties of Mn-Zn ferrites powders were investigated. Mn_xZn1 _− xFe₂O₄ powders where x = 0.2; 0.35; 0.5; 0.65; 0.8 and 1.0 were obtained by citrate precursor method. Citrate resin precursor was burned on air atmosphere at 400 °C for 3 h. Mn-Zn powders were calcined at 950 °C during 150 min under inert atmospheres: N₂ and rarefied atmosphere. Thermal analysis of precursor resin, phase evolution and microstructure of Mn-Zn ferrites powders were investigated by TG, DTA, XRD and SEM techniques. The powders calcined under rarefied atmosphere show spinel cubic structure and contamination of α-Fe₂O₃, while powders calcined under N₂ presents only the spinel cubic structure. Particle size was observed by SEM ranging from 80 to 150 nm. The magnetic properties were measured employing a vibrating sample magnetometer (VSM). It was observed that the saturation magnetization M_s increased with the increase of Mn content. The M_s of Mn_0.8Zn_0.2Fe₂O₄ calcined on rarefied atmosphere and Mn_0.8Zn_0.2Fe₂O₄ calcined on N₂ was 23.31 emu g⁻¹ and 56.23 emu g⁻¹, respectively.     

Microwave dielectric properties of BaO-2(1 − x)ZnO-xNd2O3-4TiO2 (x = 0-1.0) ceramics

Microwave dielectric properties of (1 − x)BaZn₂Ti₄O₁₁-xBaNd₂Ti₄O₁₂ (x = 0-1.0) ceramics were investigated by the solid-state reaction with the purpose of finding a microwave ceramics with high dielectric constant (?_r), high quality factor (Q × f) and low temperature coefficient of resonant frequency (τ_f). A two phase system BaZn₂Ti₄O₁₁-BaNd₂Ti₄O₁₂ was formed and SEM photographs show equiaxed BaZn₂Ti₄O₁₁ grains and columnar BaNd₂Ti₄O₁₂ grains. The microwave dielectric properties were strongly determined by the chemical composition. As increasing x from 0 to 1.0, the phase composition varied from pure BaZn₂Ti₄O₁₁, to the two phase system BaZn₂Ti₄O₁₁-BaNd₂Ti₄O₁₂ and then to pure BaNd₂Ti₄O₁₂. Therefore, the ?_r raised from 29.1 to 82.0 and the Q × f values decreased from 54,630 GHz to 8110 GHz, and the τ_f values increased from −29 ppm/°C to 94 ppm/°C. 0.8BaZn₂Ti₄O₁₁-0.2BaNd₂Ti₄O₁₂ ceramics sintered at 1250 °C for 2.5 h had ?_r = 39.1, Q × f = 37,850 GHz and τ_f = −9 ppm/ °C.     

Structural and magnetic properties of NiFe2−xBixO4 (x = 0, 0.1, 0.15) nanoparticles prepared via sol-gel method

NiFe_2−xBi_xO₄ (x = 0, 0.1, 0.15) nanopowders were synthesized via sol-gel method. The precursor gels were calcined at 773 K in air for 1 h to obtain the pure nanostructured NiFe_2−xBi_xO₄ spinel phase. The crystal structure and magnetic properties of the substituted spinel series of NiFe_2−xBi_xO₄ have been investigated by means of ⁵⁷Fe Mössbauer spectroscopy, transmission electron microscopy and alternating gradient force magnetometry. Mössbauer spectroscopic measurements revealed that Bi³⁺ cations tend to occupy octahedral positions in the structure of the substituted ferrite, i.e., the crystal-chemical formula of the as-prepared nanoparticles may be written as: (Fe)[NiFe_1−xBi_x]O₄ (x = 0, 0.1, 0.15), where parentheses and square brackets enclose cations on sites of tetrahedral and octahedral coordination, respectively. Selective area electron diffraction studies provided evidence that the samples of the NiFe_2−xBi_xO₄ series, independently of x, exhibit the cubic spinel structure. The values of the saturation magnetization and the coercive field of NiFe_2−xBi_xO₄ nanoparticles were found to decrease with increasing degree of bismuth substitution.     

Microstructure and dielectric properties of Ba0.6Sr0.4TiO3-MgAl2O4 composite ceramics

(1 − x)Ba_0.6Sr_0.4TiO₃-xMgAl₂O₄(x = 25, 30, 35 and 40 wt%) composite ceramics were prepared by conventional solid-state reaction method. The microstructures, dielectric properties and tunability of the composites have been investigated. The XRD patterns analysis reveals two crystalline phases, a cubic perovskite structure Ba_0.6Sr_0.4TiO₃ (BST) and a spinel structure MgAl₂O₄ (MA). SEM observations show that the BST grains slightly dwindle and agglomerate with increasing amounts of MA. A dielectric peak with very strong frequency dispersion is observed at higher MA content, and the Curie temperature shifts to a higher temperature with increasing MA content. The ceramic sample with 30 wt% MA has the optimized properties: the dielectric constant is 1503, the dielectric loss is 0.003 at 10 kHz and 25 °C, the tunability is 23.63% under a dc electric field of 1.0 kV/mm, which is suitable for ferroelectric phase shifter.     

Double channel electrode flow cell application to the study of HO2 production on MnxCo3−xO4 (0 ≤ x ≤ 1) spinel films

We conducted a study on the electroreduction of O₂ in alkaline solution at room temperature on pure thin oxide electrodes of composition Mn_xCo_3−xO₄ (0 ≤ x ≤ 1) using the double channel electrode flow cell (DCEFC). The oxides were prepared at 150 °C and deposited by spray pyrolysis onto titanium substrates. The oxygen reduction reaction (orr) occurs through “interactive” and “parallel” pathways, and the ratio of O₂ molecules reduced to OH⁻ ions with respect to those reduced to HO₂⁻ ions depends on the oxide stoichiometry and on the applied overpotential. The formation of HO₂⁻ increases when the manganese concentration increases. The results obtained for the orr show that the number of electrons transferred per O₂ molecule decreases from 3 to 2 and the ratio k₁/k₂ (the rate constants for direct reduction to OH⁻ and indirect reduction to HO₂⁻) increases, respectively, in the overpotential studied range (−0.05 to −0.6 V). The Mn³⁺ ions placed in the B-sites of the spinel structure seem to be the active centres, where hydrogen peroxide is formed.     

Preparation of Ni/MgxTi1 − xO catalysts and investigation on their stability in tri-reforming of methane

Ni/Mg_xTi_1 − xO catalysts were prepared through a wet impregnation method by dispersing Ni on Mg_xTi_1 − xO composite oxides obtained via a sol–gel technique. The Ni/Mg_xTi_1 − xO catalysts were characterized by various means including ICP–OES, BET, XRD, H₂–TPR, SEM, and TG. No free NiO peak was found in all XRD patterns of the Ni/Mg_xTi_1 − xO catalysts. The H₂–TPR and chemisorption results indicated that adding Ti to the NiO–MgO system obstructed the formation of solid solution, and thus increased the reducibility of the catalysts. The prepared Mg_xTi_1 − xO composite oxides had the same ability to disperse Ni as TiO₂ and MgO. The tri-reforming (simultaneous oxygen reforming, carbon dioxide reforming, and steam reforming) of methane over Ni/Mg_xTi_1 − xO catalysts was carried out in a fixed bed flow reactor. The conversions of CH₄ and CO₂ can respectively be achieved as high as above 95% and 83% over Ni/Mg_0.75Ti_0.25O catalyst under the reaction conditions. The activity of Ni/Mg_0.75Ti_0.25O and Ni/Mg_0.5Ti_0.5O did not decrease for a reaction period of 50 h, indicating their rather high stability. The experimental results showed that the nature of support, the interaction between metal and support, and the ability to be reduced played an important role in improving the stability of catalysts.     

Synthesis of negative thermal expansion materials ZrW2−xMoxO8 (0 ≤ x ≤ 2) using hydrothermal method

Negative thermal expansion materials ZrW_2−xMo_xO₈ (0 ≤ x ≤ 2) have been successfully synthesized by the reaction of a mixture of ammonium tungstate and ammonium molybdate with zirconium oxynitrate using a hydrothermal method. Effect of substituted ion Mo on the microstructure, α-to-β and cubic to trigonal phase transition in resulting ZrW_2−xMo_xO₈ powders was examined by the XRD experiments. It was found that the structural phase transition temperature decreased slightly with increasing substituted content. The cubic to trigonal phase transition was also influenced by substituted content. The resulting products decomposed to WO₃/MoO₃ and ZrO₂ as temperature increasing when x ≤ 0.5 and while x > 0.5, the cubic phase transited to trigonal phase. The effect of substituted Mo on the morphology of resulting products was also investigated by SEM experiments.     

Microstructural and electrical behavior of Bi4V2−xCuxO11−δ (0 ≤ x ≤ 0.4)

Cation substituted bismuth vanadate possesses high oxygen ion conductivity at lower temperatures. The ionic conductivity of this material at 300 °C is 50–100 times more than any other solid electrolyte. Three phases (α, β, γ) are observed in the substituted compound; α and γ are low and high conducting phase, respectively. Samples of Bi₄V_2−xCu_xO_11−δ (x = 0–0.4) were prepared by solid-state reaction technique. Impedance spectroscopy measurements were carried out in the frequency range of 100 Hz to 100 kHz using gold sputtered cylindrical shaped pellets to obtain bulk ionic conductivities as a function of the substitution and temperature. The change of slopes observed in the Arrhenius plots is in agreement with the phase transitions for all the compositions. The highest ionic conductivity of the Cu-substituted compound was observed in Bi₄V_1.8Cu_0.2O_11−δ which is attributed to its lower activation energy. Microstructural studies indicated the stabilization of high temperature γ-phase at low temperature in those samples whose ionic conductivity observed was higher.     

Microwave dielectric properties of the (1 − x)Mg2TiO4-xCaTiO3-y wt.% ZnNb2O6 ceramics system

Composite ceramics based on (1 − x)Mg₂TiO₄-xCaTiO₃-y wt.% ZnNb₂O₆ (x = 0.12-0.16, y = 0-8) were prepared by a conventional mixed-oxide route. Zn²⁺ partially replaced Mg²⁺ in Mg₂TiO₄ and formed the spinel-structured (Mg_1−δZn_δ)₂TiO₄ phase. Nb²⁺, is known to be solid soluble in CaTiO₃, was found to change its shape from cubic to pliable. A bi-phase system (Mg_1−δZn_δ)₂TiO₄ and CaTiO₃ exhibited in all samples, where a small amount of second phase Mg_1−δZn_δTiO₃ was also detected. The microwave dielectric properties of specimens were strongly related to ZnNb₂O₆ and CaTiO₃ content. As y increased, ?_r and τ_f decreased, however, Q × f decreased to a minimum value and started to increase thereafter. It was also found that ?_r and τ_f increased and Q × f decreased with increasing x. The optimized microwave dielectric properties with ?_r = 18.37, Q × f = 31,027 GHz (at 6 GHz), and τ_f = 0.51 ppm/°C were achieved for (1 − x)Mg₂TiO₄-xCaTiO₃-y wt.% ZnNb₂O₆ (x = 0.12, y = 4) sintered at 1360 °C for 6 h.     

Synthesis, characterization and optical properties of Zn1−xTixO nanoparticles prepared via a high-energy ball milling technique

Zn_1−xTi_xO (x = 0, 0.01, 0.03 and 0.05) nanoparticles were prepared by high-energy ball milling at 400 rpm. The milled powders were characterized by X-ray diffractometer (XRD) and the results exhibited that Ti-doped ZnO nanoparticles consisted of single phase with hexagonal structure when the mixtures of ZnO and TiO₂ powders were milled for 20 h. The crystallite size reduced as a function of the doping content and milling time from 1 to 10 h then increased after milling for 20 h and when the annealing temperature increased. The strain changed inversely to the crystallite size. A wider band-gap was obtained by increasing the doping content and annealing temperature because of a reduction in defect concentration. Both ZnO- and Ti-doped ZnO nanoparticles caused damage to S. aureus, E. coli, P. mirabilis, S. typhi and P. aeruginosa.     

Preparation, characterization and electrical conductivity studies of NdYb1−xGdxZr2O7 (0 ≤ x ≤ 1.0) ceramics

Several compositions of NdYb_1−xGd_xZr₂O₇ (0 ≤ x ≤ 1.0) ceramics were prepared by pressureless-sintering method at 1973 K for 10 h in air. The relative density, microstructure and electrical conductivity of NdYb_1−xGd_xZr₂O₇ ceramics were analyzed by the Archimedes method, X-ray diffraction, scanning electron microscopy and impedance plots measurements. NdYb_1−xGd_xZr₂O₇ (0 ≤ x ≤ 0.3) ceramics have a single phase of defect fluorite-type structure, and NdYb_1−xGd_xZr₂O₇ (0.7 ≤ x ≤ 1.0) ceramics exhibit a single phase of pyrochlore-type structure; however, the NdYb_0.5Gd_0.5Zr₂O₇ composition shows mixed phases of both defect fluorite-type and pyrochlore-type structures. The measured values of the grain conductivity obey the Arrhenius relation. The grain conductivity of each composition in NdYb_1−xGd_xZr₂O₇ ceramics gradually increases with increasing temperature from 673 to 1173 K. NdYb_1−xGd_xZr₂O₇ ceramics are oxide-ion conductor in the oxygen partial pressure range of 1.0 × 10⁻⁴ to 1.0 atm at all test temperature levels. The highest grain conductivity value obtained in this work is 1.79 × 10⁻² S cm⁻¹ at 1173 K for NdYb_0.3Gd_0.7Zr₂O₇ composition.     

Preparation and microstructural characterization of (Nd1−xGdx)2(Ce1−xZrx)2O7 solid solutions

(Nd_1−xGd_x)₂(Ce_1−xZr_x)₂O₇ (0 ≤ x ≤ 1.0) powders with an average particle size of 100 nm were synthesized with chemical-coprecipitation and calcination method, and were characterized by X-ray diffractometry and scanning electron microscopy. The sintering behaviour of (Nd_1−xGd_x)₂(Ce_1−xZr_x)₂O₇ powders was studied by pressureless sintering at 1600–1700 °C for 10 h in air. The relative densities of (Nd_1−xGd_x)₂(Ce_1−xZr_x)₂O₇ solid solutions increase with increasing the sintering temperature, and gradually decrease with increasing the content of neodymium and cerium at identical temperature levels. (Nd_1−xGd_x)₂(Ce_1−xZr_x)₂O₇ solid solutions have a single phase of defect fluorite-type structure among all the composition combinations studied. The lattice parameters of (Nd_1−xGd_x)₂(Ce_1−xZr_x)₂O₇ solid solutions agree well with the Vegard's rule.     

Structural evolution, sintering behavior and microwave dielectric properties of (1 − x)Li3NbO4-xLiF (0 ≤ x ≤ 0.9)

Sintering behavior, microstructure and microwave dielectric properties of (1 − x)Li₃NbO₄-xLiF (0 ≤ x ≤ 0.9) ceramics have been studied in this paper. Continuous solid solution with rock salt structure formed across the entire compositional range. Phase transformed from ordered body-centered cubic phase to short range ordered face-centered cubic phase with the addition of LiF. The x > 0.4 compositions could be densified at 850 °C/2 h. The optimized Q × f value for each composition increased with the increase of LiF content and saturated at about 75,000 GHz when x ≥ 0.15, whereas the optimized dielectric permittivity decreased with the increase of LiF content. All specimens exhibited negative τ_f value. The chemical compatibilities with copper (Cu) in the case of x = 0.4 composition and silver (Ag) in the case of x = 0.5 composition were also investigated, respectively. No chemical reaction has taken place between the matrix phase and Ag or Cu after sintering at 850 °C/2 h or 950 °C/2 h, respectively.     

Structural and magnetic properties of Co1−xZnxFe2O4 nanorods prepared by the solvothermal annealing method

Co_1−xZn_xFe₂O₄ (0.1≤x≤0.9) nanorods have been prepared by the thermal decomposition of the corresponding oxalate precursor, which was synthesized by the template-, surfactant-free solvothermal method. The as-prepared samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), fourier transform infrared spectroscopy (FTIR) and vibrating sample magnetometry (VSM). The obtained Co_1−xZn_xFe₂O₄ (0.1≤x≤0.9) nanorods were built by many nanoparticles with average sizes around 20 nm to form one-dimensional arrays. Vibrating sample magnetometry measurements show that the coercivity of the ferrite nanorods decreases with increasing Zn content, whereas the specific saturation magnetization initially increases and then decreases with the increase of Zn content. The maximum saturation magnetization value of the as-prepared sample (Co_0.5Zn_0.5Fe₂O₄) reaches 43.0 emu g⁻¹.     

Soft template synthesis of mesoporous Co3O4/RuO2·xH2O composites for electrochemical capacitors

Co₃O₄/RuO₂·xH₂O composites with various Ru content (molar content of Ru = 5%, 10%, 20%, 50%) were synthesized by one-step co-precipitation method. The precursors were prepared via adjusting pH of the mixed aqueous solutions of Co(NO₃)₂·6H₂O and RuCl₃·0.5H₂O by using Pluronic123 as a soft template. For the composite with molar ratio of Co:Ru = 1:1 annealed at 200 °C, Brunauer-Emmet-Teller (BET) results indicated that the composite showed mesoporous structure, and the specific surface area of the composite was as high as 107 m² g⁻¹. The electrochemical performances of these composites were measured in 1 M KOH electrolyte. Compared with the composite prepared without template, the composite with P123 exhibited a higher specific capacitance. When the molar content of Ru was rising, the specific capacitance of the composites increased significantly. It was also observed that the crystalline structures as well as the electrochemical activities were strongly dependent on the annealing temperature. A capacitance of 642 F/g was obtained for the composite (Co:Ru = 1:1) annealed at 150 °C. Meanwhile, the composites also exhibited good cycle stability. Besides, the morphologies and textural characteristic of the samples were also investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM).     

Microstructures and dielectric properties of spark plasma sintered Ba0.4Sr0.6TiO3/CaCu3Ti4O12 composite ceramics

(1 − x)Ba_0.4Sr_0.6TiO₃/xCaCu₃Ti₄O₁₂ composite ceramics were prepared by spark plasma sintering. Sintering behavior, microstructures and dielectric properties of the composite ceramics were investigated by XRD, SEM, EDS and dielectric spectrometer. Dense composite ceramics consisting of Ba_0.4Sr_0.6TiO₃ phase and CaCu₃Ti₄O₁₂ phase were prepared at 800 °C for 0 min. The dielectric loss of the composite ceramic decreased with increasing amount of Ba_0.4Sr_0.6TiO₃, and the high dielectric constant were retained. Moreover, the better temperature stability of dielectric constant was obtained. These improvements of dielectric characteristics have great scientific significance for potential application.     

Spinel precipitation in Sn4+-doped Co1−xO polycrystals with dispersed Co2+xSn1−xO4 particles

Co_1?xO–SnO₂ powders in molar ratio of 92:8 were reactively sintered at 1400 °C to form Co_1?xO–Co_2+xSn_1?xO₄ composite and then cooled in furnace or air quenched for secondary Co_2+xSn_1?xO₄ spinel precipitation from the Sn⁴⁺ doped Co_1?xO grains. Electron microscope observations indicated the secondary spinel to precipitate at grain boundaries when slowly cooled, but as parallel-epitaxial platelets within the Sn⁴⁺ doped Co_1?xO grains with a precipitate free zone near the grain boundary when air quenched. A process of thermal-mismatch induced {1 1 0} cleaving, taking advantage of cobalt vacancies, and spontaneous healing by oxidation precipitation accounts for the platy spinel precipitation within the grains. The precipitate free zone can be attributed to cobalt vacancy depletion, i.e. site saturation, near the grain boundary during rapid cooling in air. The spinel nanocrystals nucleated from cobalt vacancies in association with Sn⁴⁺ dopant have well-developed {1 1 1} habit plane in order to minimize the coherency strain energy.     

LiNi0.8Co0.15Al0.05O2 cathode materials prepared by TiO2 nanoparticle coatings on Ni0.8Co0.15Al0.05(OH)2 precursors

Synthesis, electrochemical, and structural properties of LiNi_0.8Co_0.15Al_0.05O₂ cathodes prepared by TiO₂ nanoparticles coating on a Ni_0.8Co_0.15Al_0.05(OH)₂ precursor have been investigated by the variation of coating concentration and annealing temperature. TiO₂-coated cathodes showed that Ti elements were distributed throughout the particles. Among the coated cathodes, the 0.6 wt% TiO₂-coated cathode prepared by annealing at 750 °C for 20 h exhibited the highest reversible capacity of 176 mAh g⁻¹ and capacity retention of 92% after 40 cycles at a rate of 1C (=190 mA g⁻¹). On the other hand, an uncoated cathode showed a reversible first discharge capacity of 186 mAh g⁻¹ and the same capacity retention value to the TiO₂-coated sample at a 1C rate. However, under a 1C rate cycling at 60 °C for 30 cycles, the uncoated sample showed a reversible capacity of 40 mAh g⁻¹, while a TiO₂-coated one showed 71 mAh g⁻¹. This significant improvement of the coated sample was due to the formation of a possible solid solution between TiO₂ and LiNi_0.8Co_0.15Al_0.05O₂. This effect was more evident upon annealing the charged sample while increasing the annealing temperature, and at 400 °C, the coated one showed a more suppressed formation of the NiO phase from the spinel LiNi₂O₄ phase than the uncoated sample.