Sintering of Al2O3-SiC composite from sol-gel method with MgO, TiO2 and Y2O3 addition

Al₂O₃-SiC composite ceramics were prepared by pressureless sintering with and without the addition of MgO, TiO₂ and Y₂O₃ as sintering aids. The effects of these compositional variables on final density and hardness were investigated. In the present article at first α-Al₂O₃ and β-SiC nano powders have been synthesized by sol-gel method separately by using AlCl₃, TEOS and saccharose as precursors. Pressureless sintering was carried out in nitrogen atmosphere at 1600 °C and 1630 °C. The addition of 5 vol.% SiC to Al₂O₃ hindered densification. In contrast, the addition of nano MgO and nano TiO₂ to Al₂O₃-5 vol.% SiC composites improved densification but Y₂O₃ did not have positive effect on sintering. Maximum density (97%) was achieved at 1630 °C. Vickers hardness was 17.7 GPa after sintering at 1630 °C. SEM revealed that the SiC particles were well distributed throughout the composite microstructures. The precursors and the resultant powders were characterized by XRD, STA and SEM.     

Structural and optical properties of Tm:Y2O3 transparent ceramic with La2O3, ZrO2 as composite sintering aid

The paper reports the use of La₂O₃ and ZrO₂ co-doping as a composite sintering aid for the fabrication of Tm:Y₂O₃ transparent ceramics. Two groups of experiments were conducted for investigating the influences of composite sintering aids on the microstructures and the optical properties of Tm:Y₂O₃ transparent ceramics in contrast to single La³⁺ and single Zr⁴⁺ doped Tm:Y₂O₃. Samples with composite sintering aids could realize fine microstructures and good optical properties at relatively low sintering temperatures. Grain sizes around 10 μm and transmittances close to theoretical value at wavelength of 2 μm were achieved for the 9 at.% La³⁺, 3 at.% Zr⁴⁺ co-doped samples sintered at 1500-1600 °C. The influences of the composite sintering aids on the emission intensities and the phonon energies of Tm:Y₂O₃ ceramics were also investigated.     

Effect of CeO2 addition on densification and microstructure of Al2O3-YSZ composites

Alumina (Al₂O₃) and alumina-yttria stabilized zirconia (YSZ) composites containing 3 and 5 mass% ceria (CeO₂) were prepared by spark plasma sintering (SPS) at temperatures of 1350-1400 °C for 300 s under a pressure of 40 MPa. Densification, microstructure and mechanical properties of the Al₂O₃ based composites were investigated. Fully dense composites with a relative density of approximately 99% were obtained. The grain growth of alumina was inhibited significantly by the addition of 10 vol% zirconia, and formation of elongated CeAl₁₁O₁₈ grains was observed in the ceria containing composites sintered at 1400 °C. Al₂O₃-YSZ composites without CeO₂ had higher hardness than monolithic Al₂O₃ sintered body and the hardness of Al₂O₃-YSZ composites decreased from 20.3 GPa to 18.5 GPa when the content of ZrO₂ increased from 10 to 30 vol%. The fracture toughness of Al₂O₃ increased from 2.8 MPa m^1/2 to 5.6 MPa m^1/2 with the addition of 10 vol% YSZ, and further addition resulted in higher fracture toughness values. The highest value of fracture toughness, 6.2 MPa m^1/2, was achieved with the addition of 30 vol% YSZ.     

Preparation of nanocrystalline Sr3Al2O6 powders via citric acid precursor

Sr₃Al₂O₆ was synthesized via citric acid precursor. The effects of the molar ratio of citric acid to total metal cations concentration (CA/M) on the formation of Sr₃Al₂O₆ were investigated. Increasing the CA/M promoted the formation of Sr₃Al₂O₆. Single-phase and well-crystallized Sr₃Al₂O₆ was obtained from the CA/M = 1, CA/M = 2 and CA/M = 4 precursor at temperature 1200 °C, 1100 °C and 900 °C, respectively. Differential thermal analysis and thermogravimetric (DTA/TG), X-ray diffractometry (XRD) and field emission scanning electron microscopy (FESEM) were used to characterize the precursors and the derived oxide powders. Sr₃Al₂O₆ nanoparticles with a diameter of about 50-70 nm were obtained.     

Improvement of microstructural properties of 3Y-TZP materials by conventional and non-conventional sintering techniques

3 mol% Y₂O₃-stabilized zirconia nanopowders were fabricated using various sintering techniques; conventional sintering (CS) and non-conventional sintering such as microwave (MW) and pulsed electric current-assisted-sintering (PECS) at 1300 °C and 1400 °C. A considerable difference in the densification behaviour between conventional and non-conventional sintered specimens was observed. The MW materials attain a bulk density 99.4% theoretical density (t.d.) at 1300 °C, while the CS materials attain only 92.5% t.d. and PECS 98.7% t.d. Detailed microstructural evaluation indicated that a low temperature densification leading to finer grain sizes (135 nm) could be achieved by PECS followed by MW with an average sintered grain size of 188 nm and CS 225 nm. It is believed that the high heating rate and effective particle packing are responsible for the improvements in these properties.     

Transparent polycrystalline MgAl2O4 ceramic fabricated by spark plasma sintering: Microwave dielectric and optical properties

The optical properties and microwave dielectric properties of transparent polycrystalline MgAl₂O₄ ceramics sintered by spark plasma sintering (SPS) through homemade nanosized MgAl₂O₄ powders at temperatures between 1250 °C and 1375 °C are discussed. The results indicate that, with increasing sintering temperatures, grain growth and densification occurred up to 1275 °C, and above 1350 °C, rapid grain and pore growth occurred. The in-line light transmission increases with the densification and decreases with the grain/pore growth, which can be as high as 70% at the wavelength of 550 nm and 82% at the wavelength of 2000 nm, respectively. As the sintering temperature increases, Q×f and dielectric constant ε_r values increase to maximum and then decrease respectively, while τ_f value is almost independent of the sintering temperatures and remains between −77 and −71 ppm/°C. The optimal microwave dielectric properties (ε_r=8.38, Q×f=54,000 GHz and τ_f=−74 ppm/°C) are achieved for transparent MgAl₂O₄ ceramics produced by spark plasma sintering at 1325 °C for 20 min.     

Phase diagram of the Al2O3-HfO2-Y2O3 system

The phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system was first constructed in the temperature range 1200-2800 °C. The phase transformations in the system are completed in eutectic reactions. No ternary compounds or regions of appreciable solid solution were found in the components or binaries in this system. Four new ternary and three new quasibinary eutectics were found. The minimum melting temperature is 1755 °C and it corresponds to the ternary eutectic Al₂O₃ + HfO₂ + Y₃Al₅O₁₂. The solidus surface projection, the schematic of the alloy crystallization path and the vertical sections present the complete phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system.     

Processing and physical properties of Al2O3/aluminum alloy composites

Porous aluminum oxide (Al₂O₃) preforms were formed by sintering in air at 1200 °C for 2 h. A356, 6061, and 1050 aluminum alloys were infiltrated into the preforms by squeeze casting in order to fabricate Al₂O₃/A356, Al₂O₃/6061, and Al₂O₃/1050 composites, respectively, with different volumes of aluminum alloy content. The content of aluminum alloy in the composites was 10–40% by volume. The resistivity of Al₂O₃/A356, Al₂O₃/6061, and Al₂O₃/1050 composites decreased dramatically from 6.41 × 10¹² to 9.77 × 10⁻⁴, 7.28 × 10⁻⁴, and 6.24 × 10⁻⁴ Ω m, respectively, the four-points bending strength increased from 397 to 443, 435.1, 407.2 MPa, respectively, and the deviations were smaller than 2%. From SEM microstructural analysis and TEM bright field images, the pore volume fraction and the relative density of the composites were the most important factors that affected the physical and mechanical properties. The ceramic phase and alloy phase in Al₂O₃/aluminum alloy composites were found to be homogenized and uniformly distributed using electrical and mechanical properties analysis, microstructure analysis, and image analysis.     

Efficient production of hydrogen and multi-walled carbon nanotubes from ethanol over Fe/Al2O3 catalysts

Fe/Al₂O₃ catalysts with different Fe loadings (10-90 mol%) were prepared by hydrothermal method. Ethanol decomposition was studied over these Fe/Al₂O₃ catalysts at temperatures between 500 and 800 °C to produce hydrogen and multi-walled carbon nanotubes (MWCNTs) at the same time. The results showed that the catalytic activity and stability of Fe/Al₂O₃ depended strongly on the Fe loading and reaction temperature. The Fe(30 mol%)/Al₂O₃ and Fe(40 mol%)/Al₂O₃ were both the effective catalyst for ethanol decomposition into hydrogen and MWCNTs at 600 °C. Several reaction pathways were proposed to explain ethanol decomposition to produce hydrogen and carbon (including nanotube) at the same time.     

Preparation of columbite MgNb2O6 and ZnNb2O6 ceramics by reaction-sintering

Columbite MgNb₂O₆ (MN) and ZnNb₂O₆ (ZN) ceramics produced by the reaction-sintering process were investigated. Secondary phases Mg_0.652Nb_0.598O_2.25 and Mg_0.66Nb_11.33O₂₉ were found in MgNb₂O₆ pellets. After 1250 °C sintering for 2 h, a density 4.85 g/cm³ (97.1% of the theoretical value) was obtained in MgNb₂O₆ pellets. In ZnNb₂O₆ pellets, no secondary phase formed. The maximum density 5.55 g/cm³ (98.7% of the theoretical value) occurs at 1200 and 1180 °C sintering for 2 and 4 h, respectively.     

Preparation of ZrO2/Gd2O3 composite ceramic materials by coprecipitation method

High burnup is a goal for further development of advanced nuclear power in the future. However, along with the increase of burnup, it becomes more diffidult to control reactor reactivity, which affects the operation safety of the nuclear reactor. Al₂O₃/B₄C burnable poison materials widely used in pressurized water reactor currently will not meet the requirements of burnable poison materials in high burnup nuclear power. Because of the better performance of ZrO₂/Gd₂O₃ burnable poison materials than that of Al₂O₃/B₄C, this paper studies the preparation of ZrO₂/Gd₂O₃ composite ceramic materials by the coprecipitation method. The experimental results show that at the sintering temperature of 1500–1650 °C, ZrO₂/Gd₂O₃ composite ceramic grains are small, compact and uniform with the generation of homogeneous solid solution. At 1600 °C, ZrO₂–10%Gd₂O₃ has the highest density and mechanical strength.     

Synthesis of Zn3Nb2O8 ceramics using a simple and effective process

Synthesis of Zn₃Nb₂O₈ ceramics using a simple and effective reaction-sintering process was investigated. The mixture of ZnO and Nb₂O₅ was pressed and sintered directly without any prior calcination. Single-phase Zn₃Nb₂O₈ ceramics could be obtained. Density of these ceramics increased with soaking time and sintering temperature. A maximum density 5.72 g/cm³ (99.7% of the theoretical density) was found for pellets sintered at 1170 °C for 2 h. Pores were not found and grain sizes >20 μm were observed in pellets sintered at 1170 °C. Abnormal grain growth occurred and grains >50 μm could be seen in Zn₃Nb₂O₈ ceramics sintered at 1200 °C for 2 h and 1200 °C for 4 h. Reaction-sintering process is then a simple and effective method to produce Zn₃Nb₂O₈ ceramics for applications in microwave dielectric resonators.     

Effects of CaSiO3 addition on sintering behavior and microwave dielectric properties of Al2O3 ceramics

The effects of CaSiO₃ addition on the sintering behavior and microwave dielectric properties of Al₂O₃ ceramics have been investigated. The addition of CaSiO₃ into Al₂O₃ ceramics resulted in the emergence of Ca₂Al₂SiO₇ and CaAl₂Si₂O₈, which acting as liquid sintering aids can effectively lower the sintering temperature of Al₂O₃ ceramic. The Q × f value of Al₂O₃-CaSiO₃ ceramics decreased with the CaSiO₃ addition increasing because of the lower Q × f value of Ca₂Al₂SiO₇ and CaAl₂Si₂O₈. Compared with the pure CaSiO₃ ceramic, the Al₂O₃-CaSiO₃ ceramic with 20 wt% CaSiO₃ addition possessed good dielectric properties of ?_r = 9.36 and Q × f = 13,678 GHz at the similar sintering temperature.     

Influence of sintering temperature and holding time on the densification, phase transformation, microstructure and properties of hot pressing WC-40 vol.%Al2O3 composites

WC-40 vol.%Al₂O₃ composites were prepared by high energy ball milling followed by hot pressing. The tungsten carbide (WC) and commercial alumina (Al₂O₃) powders composed of amorphous Al₂O₃, boehmite (AlOOH) and χ-Al₂O₃ were used as the starting materials. The phase transformation during sintering, the influence of sintering temperature and holding time on the densification, microstructure, Vickers hardness and fracture toughness and the toughening effects of WC-40 vol.%Al₂O₃ composites were investigated. The results showed that the amorphous Al₂O₃, AlOOH and χ-Al₂O₃ were transformed to α-Al₂O₃ completely during the sintering process. With the increasing sintering temperature and holding time, the relative density increased and both the Vickers hardness and fracture toughness increased initially to the maximum values and then decreased. When the as milled powders were hot pressed at 1540 °C for 90 min, a relative density of 97.98% and a maximum hardness of 18.65 GPa with an excellent fracture toughness of 10.43 MPa m^1/2 of WC-40 vol.%Al₂O₃ composites were obtained.     

Two-step pulsed electric current sintering of transparent Al2O3 ceramics

Abstract

Fully densified Al₂O₃ ceramics with fine grain size were obtained by pulsed electric current sintering through a two-step heating profile (referred to as TS-PECS). Highly transparent Al₂O₃ polycrystals with fine grain size (400 nm) were successfully fabricated by the TS-PECS process, namely, sintering at 1000°C for 1 h and followed at 1200°C for 20 min under uniaxial pressure of 100 MPa. Effects of the first step temperature and heating rate were discussed for bulk density, grain size and transparency. The temperature in the first step strongly affects densification and grain growth of Al₂O₃. On the other hand, heating rate, even of 100 K min^?1, in TS-PECS does not give significant influences on densification and grain growth of Al₂O₃. Inline transmittance at 640 nm in wavelength normalised to 1 mm in thickness is increased by decreasing heating rate even in TS-PECS.     

Sintering,microstrusture and hardness of different alumina–zirconia composites

Two commercial 3 mol% yttria-partially stabilized zirconia powders, 0.3 wt% Al₂O₃-doped (Al-doped Y-PSZ) and without Al₂O₃ (Y-PSZ), were used to produce alumina (Al₂O₃)-zirconia (ZrO₂) slip cast composites. The influence of the substitution of Al₂O₃ either by different Al-doped Y-PSZ contents or 50 vol% Y-PSZ on the sintering kinetic at the intermediate stage was investigated. In addition, the microstructure of Al₂O₃ and the different composites at temperatures in the range of 1100–1600 °C was studied and related to the sample hardness. An increase in the sintering rate was observed when Al-doped Y-PSZ increased from 22 to 50 vol% or when 50 vol% Y-PSZ was substituted by 50 vol% Al-doped Y-PSZ. 50 vol% ZrO₂ was the most effective concentration to reduce the rate of Al₂O₃ grain growth in the final sintering stage; the Al₂O₃ grain growth began at lower temperatures and became greater with decreasing the Al-doped Y-PSZ content. On the contrary, the ZrO₂ grain growth slightly increased with increasing the Al-doped Y-PSZ concentration. However, for 50 vol% Al-doped Y-PSZ a smaller ZrO₂ grain size distribution compared with 50 vol% Y-PSZ could be achieved. As the average Al₂O₃ grain size of the sintered samples became greater than about 1 µm a markedly decrease in the hardness was found; this occurred at temperatures higher than 1400 °C and 1500 °C for Al₂O₃ and the composite with 10.5 vol% Al-doped Y-PSZ, respectively.     

Long-term degradation of Ta2O5-doped Bi2O3 systems

Bismuth oxide in δ-phase is a well-known high oxygen ion conductor and can be used as an electrolyte for intermediate temperature solid oxide fuel cells (IT-SOFCs). 5-10 mol% Ta₂O₅ are doped into Bi₂O₃ to stabilize δ-phase by solid state reaction process. One Bi₂O₃ sample (7.5TSB) was stabilized by 7.5 mol% Ta₂O₅ and exhibited single phase δ-Bi₂O₃-like (type I) phase. Thermo-mechanical analyzer (TMA), X-ray diffractometry (XRD), AC impedance and high-resolution transmission electron microscopy (HRTEM) were used to characterize the properties. The results showed that holding at 800-850 °C for 1 h was the appropriate sintering conditions to get dense samples. Obvious conductivity degradation phenomenon was obtained by 1000 h long-term treatment at 650 °C due to the formation of α-Bi₂O₃ phase and Bi₃TaO₇, and 〈1 1 1〉 vacancy ordering in Bi₃TaO₇ structure.     

Relationship between fracture toughness characteristics and morphology of sintered Al2O3 ceramics

The influence of sintering temperature and soaking time on fracture toughness of Al₂O₃ ceramics has been investigated. The samples were prepared by solid state sintering at 1500, 1600 and 1700 °C for different soaking time periods. The fracture toughness of the sintered samples was determined by inducing cracks using Vickers indentation technique. Microstructural investigations on fracture surfaces obtained by three point bend test mode were made and correlated with fracture toughness. Crack deflection in the samples sintered at 1500 and 1600 °C for which ranges of fracture toughness are 5.2–5.4 and 5.0–5.6 MPa m^1/2 respectively, are found. The samples sintered at 1700 °C have lower fracture toughness ranging between 4.6 and 5.0 MPa m^1/2. These samples have larger grains and transgranular fracture mode is predominant. The crack deflection has further been revealed by SEM and AFM observations on fracture surface and fracture surface roughness respectively.     

Effects of Al2O3 addition on the sintering behavior and microwave dielectric properties of CaSiO3 ceramics

The effects of Al₂O₃ addition on the densification, structure and microwave dielectric properties of CaSiO₃ ceramics have been investigated. The Al₂O₃ addition results in the presence of two distinct phases, e.g. Ca₂Al₂SiO₇ and CaAl₂Si₂O₈, which can restrict the growth of CaSiO₃ grains by surrounding their boundaries and also improve the bulk density of CaSiO₃-Al₂O₃ ceramics. However, excessive addition (≥2 wt%) of Al₂O₃ undermines the microwave dielectric properties of the title ceramics since the derived phases of Ca₂Al₂SiO₇ and CaAl₂Si₂O₈ have poor quality factor. The optimum amount of Al₂O₃ addition is found to be 1 wt%, and the derived CaSiO₃-Al₂O₃ ceramic sintered at 1250 °C presents improved microwave dielectric properties of ?_r = 6.66 and Q × f = 24,626 GHz, which is much better than those of pure CaSiO₃ ceramic sintered at 1340 °C (Q × f = 13,109 GHz).     

Synthesis and characterization of B13C2 boron carbide ceramic by pulsed electric current sintering

Approximately 400 nm grain sized boron-carbon ceramic was synthesized by the pulsed electric current sintering (PECS) method using boron and carbon powders. Relative density of up to 95% was achieved at sintering temperature of 1900 °C. This ceramic was composed with B₁₃C₂ as major phase and few B₄C and C, which were characterized by X-ray diffraction (XRD) and Rietveld refinement quantitative analysis and chemical analysis (CA) and electron probe microanalysis (EPMA). The microstructure was also observed via transmission electron microscope (TEM).