Synthesis and NTC properties of YCr1−xMnxO3 ceramics sintered under nitrogen atmosphere

YCr_1−xMn_xO₃ (0 ≤ x ≤ 0.8) negative temperature coefficient (NTC) compositions were synthesized by classical solid state reaction at 1200 °C, and sintered under nitrogen atmosphere at 1500 °C and 1600 °C. XRD patterns analysis has revealed that for x ≤ 0.6, the structure consists of a solid solution of an orthorhombic perovskite YCrO₃ phase with Mn substitute for Cr. For x ≥ 0.8, a second phase with a structure similar to the hexagonal YMnO₃ phase appears. SEM images and calculated open porosity have shown that the substitution of Mn for Cr results in a decrease in porosity. Whatever the sintering temperature, the electrical characterizations (between 25 and 900 °C) have shown that the increase in the manganese content involves the decrease in both resistivity and material constant B (parameter which characterizes the thermal sensitivity of material) when x ≤ 0.6. The magnitude order of the resistivity at 25 °C is of 10⁴-10⁸ Ω cm and activation energies vary from 0.28 to 0.99 eV at low and high temperatures, respectively.     

Synthesis and properties of (BaxPb1−x)(Zn1/3Nb2/3)O3 relaxor ferroelectric ceramics using a reaction-sintering process

(Ba_xPb_1−x)(Zn_1/3Nb_2/3)O₃ (BPZN; x = 0.06–0.1) relaxor ferroelectric ceramics produced using a reaction-sintering process were investigated. Without any calcination involved, the mixture of raw materials was pressed and sintered directly. BPZN ceramics of 100% perovskite phase were obtained. Highly dense BPZN ceramics with a density higher than 98.5% of theoretical density could be obtained. Maximum dielectric constant K_max 13,500 (at 75 °C), 19,600 (at 50 °C) and 14,800 (at 28 °C) at 1 kHz could be obtained in 6BPZN, 8BPZN and 10BPZN, respectively. Dielectric maximum temperature (T_max) in BPZN ceramics via reaction-sintering process is lower than BPZN ceramics prepared via B-site precursor route.     

New NiFe2−xCrxO4 spinel films for O2 evolution in alkaline solutions

Spinel-type ternary ferrites with composition NiFe_2−xCr_xO₄ (0 ≤ x ≤ 1) were synthesized by a precipitation method and their physicochemical and electrocatalytic properties have been investigated using IR, XRD, BET surface area, XPS, impedance and Tafel polarization techniques. The study indicated that substitution of Cr from 0.2 to 1.0 mol in the spinel matrix increased the apparent electrocatalytic activity of the base oxide towards the O₂ evolution reaction in 1 M KOH at 25 °C. The apparent electrocatalytic activity of the oxide with 0.8-1.0 mol Cr was found to be the greatest among the present series of oxides investigated. It is noteworthy that the electrocatalytic activity of the oxide with x = 0.8-1.0 was also greater than those of other spinel/perovskite O₂ evolving electrocatalysts reported in literature.     

Preparation, characterization and dielectric properties of CaCu3Ti4O12 ceramics

CaCu₃Ti₄O₁₂ nano-sized powders were successfully prepared by sol-gel technique and calcination at 600-900 °C. The thermal decomposition process, phase structures and morphology of synthesized powders were characterized by IR, DSC-TG, XRD, TEM, respectively. It was found that the main weight-loss and decomposition of precursors occurred below 450 °C and the complex perovskite phase appeared when the calcination temperature was higher than 700 °C. Using above synthesized powders as starting materials, CCTO-based ceramics with excellent dielectric properties (?₂₅ = 5.9 × 10⁴, tan δ = 0.06 at 1.0 kHz) were prepared by sintering at 1125 °C. According to the results, a conduction mechanism was proposed to explain the origin of giant dielectric constant in CCTO system.     

Study on the rapid synthesis of LiNi1−xCoxO2 cathode material for lithium secondary battery

LiNi_1−xCo_xO₂ (x = 0, 0.1, 0.2) cathode materials were successfully synthesized by a rheological phase reaction method with calcination time of 0.5 h at 800 °C. All obtained powders are pure phase with α-NaFeO₂ structure (R-3m space group). The samples deliver an initial discharge capacity of 182, 199 and 189 mAh g⁻¹ (25 mA g⁻¹, 4.35-3.0 V), respectively. The reaction mechanism was also discussed, which consists of a series of defect reactions. As a result of these defect reactions, the reaction of forming LiNi_1−xCo_xO₂ takes place in high speed.     

Effect of La substitution on the structural and electrical properties of BaBi4−xLaxTi4O15

Pure and lanthanum doped barium bismuth titanate BaBi_4−xLa_xTi₄O₁₅ (BBLT, x=0, 0.05, 0.15, 0.30) ceramics were prepared utilizing solid state method. The X-ray diffraction (XRD) data confirmed formation of single-phase Aurivillius compounds while SEM micrographs did not show evident grain size change of doped ceramics. Dielectric properties were investigated in 1.21 kHz to 1 MHz frequency range and in the temperature range of 20 to 727 °C. When Bi³⁺ is substituted with La³⁺, a significant disorder was induced and the material exhibited broadening of the phase transition. Impedance analysis confirmed the presence of two semicircular arcs in doped samples suggesting the existence of grain and grain-boundary conduction. The dc-conductivity and activation energies were evaluated for all compositions.     

Preparation and properties of yttrium-doped SrTiO3 anode materials

Direct electrochemical oxidation of hydrocarbon fuels is a current development trend of solid oxide fuel cells (SOFCs) and finding new anode materials for this application is a key issue. In this study, promising candidates, Y₂O₃-doped SrTiO₃ perovskite compounds Sr_1−1.5xY_xTiO₃ (x = 0.02, 0.04, 0.06, 0.08, 0.10), were synthesized by solid-state reaction. The structure of the calcined powders was examined by X-ray diffraction (XRD). The sinterability and high temperature conductivity were measured by the Archimedes principle and a dc four-probe method, respectively. The effect of sintering temperature on the electrical conductivity was studied. The results indicated that the optimal sintering temperature is around 1400 °C. From 400 °C to 1000 °C, the conductivity decreased with increasing temperature. At 800 °C the highest conductivity (26.8 S/cm) was observed for x = 0.08.     

Oxidation resistance of multi-walled carbon nanotubes coated with polycarbosilane-derived SiCxOy ceramic

Multi-walled carbon nanotubes (MWCNTs) have been successfully coated with a thin SiC_xO_y coating when polycarbosilane (PCS) was used as precursor and pyrolyzed in a coke bed. Meanwhile, effect of PCS concentration on oxidation resistance of the coated MWCNTs is studied. The results showed that the pyrolysis products of PCS were composed of amorphous SiC_xO_y as the main phase, together with β-SiC and SiO₂ as the minor phases whose amount increased a little with the increase of temperature from 1000 °C to 1500 °C. The thickness of SiC_xO_y coating on the surface of MWCNTs increased a little from 1 wt.% to 5 wt.%, but decreased dramatically with PCS concentration in the range of 10-30 wt.%. The oxidation resistance of the coated MWCNTs was greatly improved in comparison with as-received ones. The oxidation peak temperature of the coated MWCNTs reached 783.7 °C, much higher than 652.2 °C for as-received ones.     

Spray pyrolysis synthesis of nanostructured LiFexMn2−xO4 cathode materials for lithium-ion batteries

A series of partially Fe-substituted lithium manganese oxides LiFe_xMn_2−xO₄ (0 ≦ x ≦ 0.3) was successfully synthesized by an ultrasonic spray pyrolysis technique. The resulting powders were spherical nanostructured particles which comprised the primary particles with a few tens of nanometer in size, while the morphology changed from spherical and porous to spherical and dense with increasing Fe substitution. The densification of particles progressed with the amount of Fe substitution. All the samples exhibited a pure cubic spinel structure without any impurities in the XRD patterns.The as-prepared powders were then sintered at 750 °C for 4 h in air. However, the particles morphology and pure spinel phase of LiFe_xMn_2−xO₄ powders did not change after sintering. The as-sintered powders were used as cathode active materials for lithium-ion batteries, and cycle performance of the materials was investigated using half-cells Li/LiFe_xMn_2−xO₄. The first discharge capacity of Li/LiFe_xMn_2−xO₄ cell in a voltage 3.5-4.4 V decreased as the value x increased, however these cells exhibited stable cycling performance at wide ranges of charge-discharge rates.     

Phase, microstructure evolution and sintering of Sr-doped TiB2 precursors

Precursors for the preparation of bulk Sr-doped TiB₂ composites were synthesized by modified Pechini method. The high temperature behaviour of homogeneous Sr-Ti-B-C-O gels was investigated in the range 1200-1650 °C. DTA-TG analysis of the precursor powder shows two steps of the carbothermal reduction with endothermic peaks at temperatures of 1335 °C and 1500 °C. The influence of strontium content (2, 5, 10, 20 and 50 mol.%) on the phase composition and morphology of powders at 1650 °C was studied.Due to the shift of TiB₂ diffractions and the detection of strontium in TiB₂ grains by EDX analysis the formation of Ti_1 − xSr_xB₂ solid solution is assumed in the Sr-doped powders. Finally, Sr-doped TiB₂ composites were inductive hot-pressed from the as prepared powders at 1900 °C for 7 min. The formation of SrTiO₃ phase in the powders is serving as a sintering aid during the preparation of bulk Sr-Ti-B composites. The exaggerated grain growth (grain size up to ∼60 μm) occurs during the sintering with increasing content of strontium in the precursor.     

Preparation and microstructural characterization of (Nd1−xGdx)2(Ce1−xZrx)2O7 solid solutions

(Nd_1−xGd_x)₂(Ce_1−xZr_x)₂O₇ (0 ≤ x ≤ 1.0) powders with an average particle size of 100 nm were synthesized with chemical-coprecipitation and calcination method, and were characterized by X-ray diffractometry and scanning electron microscopy. The sintering behaviour of (Nd_1−xGd_x)₂(Ce_1−xZr_x)₂O₇ powders was studied by pressureless sintering at 1600–1700 °C for 10 h in air. The relative densities of (Nd_1−xGd_x)₂(Ce_1−xZr_x)₂O₇ solid solutions increase with increasing the sintering temperature, and gradually decrease with increasing the content of neodymium and cerium at identical temperature levels. (Nd_1−xGd_x)₂(Ce_1−xZr_x)₂O₇ solid solutions have a single phase of defect fluorite-type structure among all the composition combinations studied. The lattice parameters of (Nd_1−xGd_x)₂(Ce_1−xZr_x)₂O₇ solid solutions agree well with the Vegard's rule.     

Re-examination of bulk and grain boundary conductivities of Ce1−xGdxO2−δ ceramics

Powders of gadolinium-doped ceria solid solutions, Ce_1−xGd_xO_2−δ (x = 0.05, 0.1, 0.2, 0.3 and 0.4), were prepared by a freeze-drying precursor route. Dense ceramic pellets with average grain sizes in the range of several microns were obtained after sintering at 1600 °C. Cobalt nitrate was added to the powders to obtain dense ceramic samples with grain sizes in the submicrometer range at 1150 °C. The ionic conduction was analysed by impedance spectroscopy in air, to de-convolute the bulk and grain boundary contributions. The bulk conductivity at low temperature clearly decreases with increasing content of Gd whereas the activation energy increases. An alternative method is proposed to analyse the extent of defect interactions on conduction. For samples without addition of Co, the specific grain boundary conductivity increases with increasing Gd content. Addition of cobalt does not alter the bulk properties but produces an important increase in the specific grain boundary conductivity, mainly in samples with lower Gd-concentration (x = 0.05 and 0.1). Segregation of Gd and its strong interaction with charge carriers may explain the blocking effects of grain boundaries.     

Synthesis and characterization of Gd0.1Ce0.9O1.95 nanopowder via an acetic–acrylicmethod

Nanocrystalline Ce_0.9Gd_0.1O_1.95 (GDC) powders are successfully prepared by an acetic–acrylic method using acrylic acid, cerium acetate and gadolinium acetate as the starting materials. The polymeric precursors are characterized by means of TG/DTA, XRD and FT-IR, and the resultant powders are characterized by XRF, BET, SEM and particle size distribution (PSD) analysis. It is shown that the morphology of the oxide particles is dependent on the preparation conditions such as molar ratio of acrylic acid to metallic ions (L/M) and the sort of surfactant. High purity, single phase, homogeneous, nanocrystalline GDC powders with slight aggregation are obtained using ethylene glycol as surfactant, L/M=0.5 and heat treatment above 600 °C. The low application amount and high effect of acrylic acid is attributed to the co-operation of carboxyl group and ethylenic bond. The electrical conductivity of the sintered GDC pellet is 0.053 Scm⁻¹ in air at 750 °C. The present work indicates that the acetic–acrylic method is a relatively green method without any NO_x to synthesize high performance GDC powders.     

Preparation and oxygen reduction activity of stable RuSex/C catalyst with pyrite structure

Carbon supported RuSe_x (x = 0.35-2) catalysts of controlled stoichiometry and phase are synthesized via precipitating ruthenium nanoparticles on Vulcan XC-72R, then selenizing ruthenium with hydrogen annealing. The competition for Se between solid-state Ru selenization and volatile selenium hydride formation results in RuSe_x nanoparticles with the pyrite structure, the Ru hcp structure, or a mixture of the two. These catalysts are methanol tolerant, and catalytically active toward oxygen reduction reaction (ORR). RuSe_x/C (x ≅ 2) with a pyrite structure, produced at 400 °C, exhibits catalytic activity and stability superior to that of RuSe_x/C with a ruthenium hcp structure or a mixed phase. And this pyrite RuSe_x/C (x ≅ 2) catalyst yields H₂O₂ less than 1.5% in the technically pertinent potential range of 0.4-0.6 V (vs. Ag/AgCl). Its stability is verified in 100 CV cycles, which shows that the catalyst annealed at 400 °C is more enduring in potential cycling over 0.65 V (vs. Ag/AgCl), compared with the RuSe_x/C catalyst annealed at 300 °C and the RuSe_cluster/C reference catalyst prepared by thermolysis of Ru₃(CO)₁₂. After CV cycles, the 400 °C-annealed catalyst still exhibits a higher ORR activity than the other two catalysts.     

Structure,dielectric and piezoelectric properties of Ba0.90Ca0.10Ti1−xSnxO3 lead-free ceramics

Lead-free piezoelectric ceramics Ba_0.90Ca_0.10Ti_1−xSn_xO₃ have been prepared by a conventional ceramic fabrication technique and the effects of Sn⁴⁺ on the structure, dielectric and piezoelectric properties of the ceramics have been investigated. All the ceramics exhibit a pure perovskite structure. After the substitution of Sn⁴⁺, the crystal structure of ceramics is transformed gradually from a tetragonal to an orthorhombic phase, and becomes a pseudo-cubic phase at x≥0.14. The substitution also decreases the Curie temperature greatly from 138 °C at x=0 to 33 °C at x=0.12, and shifts the orthorhombic–tetragonal phase transition to higher temperatures. Coexistence of the orthorhombic and tetragonal phases is formed in the ceramic at x=0.10, leading to significant improvements in the piezoelectric properties: d₃₃=521 pC/N and k_p=45.5%. Our results also reveal that the ceramics sintered at higher temperatures contain larger grains, and thus exhibit more noticeable tetragonal–orthorhombic phase transition and enhanced ferroelectric and piezoelectric properties.     

Structural and magnetic characterization of MnxZn1 − xFe2O4 (x = 0.2; 0.35; 0.65; 0.8; 1.0) ferrites obtained by the citrate precursor method

In this work the microstructure and magnetic properties of Mn-Zn ferrites powders were investigated. Mn_xZn1 _− xFe₂O₄ powders where x = 0.2; 0.35; 0.5; 0.65; 0.8 and 1.0 were obtained by citrate precursor method. Citrate resin precursor was burned on air atmosphere at 400 °C for 3 h. Mn-Zn powders were calcined at 950 °C during 150 min under inert atmospheres: N₂ and rarefied atmosphere. Thermal analysis of precursor resin, phase evolution and microstructure of Mn-Zn ferrites powders were investigated by TG, DTA, XRD and SEM techniques. The powders calcined under rarefied atmosphere show spinel cubic structure and contamination of α-Fe₂O₃, while powders calcined under N₂ presents only the spinel cubic structure. Particle size was observed by SEM ranging from 80 to 150 nm. The magnetic properties were measured employing a vibrating sample magnetometer (VSM). It was observed that the saturation magnetization M_s increased with the increase of Mn content. The M_s of Mn_0.8Zn_0.2Fe₂O₄ calcined on rarefied atmosphere and Mn_0.8Zn_0.2Fe₂O₄ calcined on N₂ was 23.31 emu g⁻¹ and 56.23 emu g⁻¹, respectively.     

Synthesis of nanosized (Pb,Sr)TiO3 perovskite powders by coprecipitation processing

Nanosized perovskite lead strontium titanate (Pb_xSr_1−x)TiO₃ (PST) powders were successfully prepared by a simple coprecipitation method. Lead-strontium titanyl oxalate (PSTO) precursor was first synthesized at room temperature, and the precursor was then calcined at 600 °C for 1 h to produce the single phase perovskite PST powders. Characterization studies were carried out on the as-dried precursor and the calcined PST powders by various techniques. The results showed a strong dependence of the chemical composition of final PST powders on pH value in the coprecipitation reaction. PST powders with desired composition could be synthesized by adding 25 mol% excess Sr. PST particles were found to be spherical in nature with an average size of 10 nm.     

Perovskite-type La2−xSrxNiO4 (0 ≤ x ≤ 1) as active anode materials for methanol oxidation in alkaline solutions

Perovskite-type ternary oxides with molecular formulae, La_2−xSr_xNiO₄ (0 ≤ x ≤ 1), were prepared by a modified citric acid sol-gel route at 600 °C for their possible use in a direct methanol fuel cell (DMFC). The study was conducted by cyclic voltammetry, chronoamperometry, impedance and anodic Tafel polarization techniques. The results showed that the electrocatalytic activity of the base oxide (x = 0) in 1 M KOH plus 1 M CH₃OH at 25 °C increases with x, the observed current densities being 23.6, 47.3, 43.2 and 50.9 mA cm⁻² at a scan rate of 10 mV s⁻¹ and E = 0.6 V versus Hg/HgO for oxides with x = 0, 0.25, 0.5 and 1.0, respectively. All the four perovskite anodes used in this study did not indicate any poisoning by the methanol oxidation intermediates/products. The methanol electro-oxidation reaction followed a Tafel slope of ∼2 × 2.303RT/3F (=40 mV decade⁻¹) on each oxide catalyst, regardless of Sr content.     

Lyothermal synthesis of nanocrystalline BaSnO3 powders

The synthesis of BaSnO₃ powders has been investigated at lyothermal conditions (temperature of 250 °C; t = 6 h), starting from SnO₂·xH₂O and Ba(OH)₂ and methanol, ethanol, isopropanol and acetone as solvents. Among them isopropanol was found to be the most suitable medium for preparing BaSnO₃. By addition of the modifier Genapol X-080 during the processing, the BET specific surface area of the end-powder was increased by a factor of 10. The as-prepared powder consisted of BaSn(OH)₆. The thermal behavior, the crystallization behavior and the structure evolution of the powder during heating treatment have been studied with the TG–DTA–MS, XRD and FTIR. The weight loss of the as-prepared powder of about 12 wt% heated up to 1200 °C is mainly attributed to the dehydration around 260 °C which leads to the structure rearrangement and the building of the [SnO₆] octahedra. At this temperature BaSn(OH)₆ converts to an amorphous phase, from which BaSnO₃ nucleates and grows with increasing temperature. The obtained BaSnO₃ powders had a BET specific surface area of 16.56 m²/g and a primary crystallite size of 49 nm.     

Compositional dependence of phase structure and electrical properties in (K0.50Na0.50)0.97Bi0.01(Nb1−xZrx)O3 lead-free ceramics

(K_0.50Na_0.50)_0.97Bi_0.01(Nb_1-xZr_x)O₃ (KNBNZ) lead-free ceramics were prepared by the conventional solid-state sintering process. Their phase structure is dependent on the Zr content in the investigated range, and the ceramics endure a phase transition from pseudocubic to orthorhombic with increasing Zr content. Improved piezoelectric properties have been observed when the poling temperature is located at ~100 °C because of the coexistence of orthorhombic and tetragonal phases. Their dielectric and piezoelectric properties were enhanced by doping Zr, the ceramic with x=0.02 showing optimal electrical properties, i.e., d₃₃~161 pC/N, k_p~0.41, Q_m~81, T_c~370 °C, and T_o−t~130 °C. These results show that the KNBNZ ceramic is a promising lead-free piezoelectric material.