Electrowetting optical switch with large aperture tuning range

In this paper, we propose an optical switch by deforming the shape of the liquid droplet. The optical switch consists of two immiscible liquids. The dye‐doped water is conductive, while the clear liquid is insulating. In the voltage‐off state, incident light can pass through the circular aperture formed of clear liquid. When the voltage is applied to the liquids, the surrounding dye‐doped water pushes to the side wall because of the effect of electric field force. So, the diameter of the circular aperture is rapidly reduced, and the incident light is absorbed by the dye‐doped water. Our results show that the device can obtain an optical attenuation (~350:1) and reasonable response time (~320 ms). The diameter of the aperture can be largely tuned from ~0.5 to ~6.2 mm as the applied voltage is changed from ~25 to ~65 V. The proposed optical switch has potential applications in light shutters, tunable irises, and variable optical attenuators.     

RGB converter based on liquid prism

In this paper, we propose a Red Green Blue (RGB) converter, which is an expanded application of electrowetting liquid prism in the micro‐systems. Four rectangular indium tin oxide (ITO) glass substrates having the same size are stacked to form the sidewalls. Another ITO electrode is fabricated and stuck on the bottom polymethyl methacrylate substrate as the opposite electrode. With two immiscible fluids in the transparent cell, the shape of the liquid–liquid interface can be deformed by electrostatic force. Three different color filters are placed under the prism. When we apply different voltages, the light beam will propagate through different filters by deforming the liquid–liquid interface. Our results show that we can obtain the light having three different colors from a non‐transparent cap's light hole. The device is capable of reasonable switch time (~75 and ~140 ms). It has a wide potential application in tunable lasers, adaptive indicators, and display systems.     

Motion‐blur‐free LCD for high‐resolution virtual reality displays

A new liquid crystal display device with fast response time, high transmittance, and low voltage for virtual reality is reported. When driven at 90 Hz with 17% duty ratio, the motion picture response time is 1.5 ms, which is comparable with cathode‐ray tube, leading to indistinguishable motion blur. Moreover, this device enables high‐resolution density because only one thin‐film transistor per pixel is needed and it has a built‐in storage capacitor.     

Synthesis and application of an alkylated pyrazole‐based azo dye for electrofluidic display

Electrofluidic display (EFD) is one of the most promising reflective displays for its full color and video speed. Colored EFD oil, normally formulated by soluble organic dyes in non‐polar solvent, dominates the color, electro‐optical behavior, and reliability performances for EFD devices. In this paper, a novel yellow electrofluidic dye with excellent solubility in non‐polar EFD solvent was achieved based on the introduction of long alkyl chain into pyrazole azo dye. The resulting EFD device fabricated by the dye showed excellent application properties, such as fast switching speed (17.8 ms), high aperture ratio (68.5%), low threshold voltage (24v), good light stability (240 h under accelerated conditions), and low backflow phenomenon.     

Electrowetting actuated liquid prism with large steering angle based on additional gravitational effects

In this paper, we propose a liquid prism based on electrowetting‐on‐dielectric and gravity effect. The device is filled with two immiscible liquids. The conductive liquid is filled in the upper part of the device, and the oil is filled in the bottom of the device. Different from the conventional liquid prism, the density of the conductive liquid is larger than that of the oil. The liquid–liquid interface can form a tilt shape when applied different voltages to the opposite sidewalls. The beam will be deflected when the light passes through the device. Our results show that the tilt angle of the liquid–liquid interface is ~45°, and the light beam can be deflected by 22.2° (?10.9° to +11.3°). The actuation time of the device is ~240 ms. The proposed liquid prism for light beam steering and tracking has potential application in laser directions, telecommunications, and scanners.     

The effect of transmittance and luminous efficiency with the application of cathode mesh mask in transparent organic light‐emitting devices

With the development of organic light‐emitting devices (OLEDs), the transparent OLED is also restricted by its efficiency and stability. Thus, in order to improve the transmittance and luminous efficiency of transparent OLED, the cathode mesh mask combined with Al:Ag alloy is adopted to prepare the cathode of transparent OLED, which would enhanced the luminance, efficiency, and transmittance of the device. With the same driving voltage, the device has the highest brightness, when the cathode thickness is 85 nm. At the voltage of 13 and 14 V, the luminance, for bottom‐emission and top‐emission, is 9501 cd/m² and 1840 cd/m², respectively. The entire transmittance of the device has achieved about 78% at a 480 nm wavelength.     

Viewing‐angle‐switching device based on array of optical micro‐rods incorporated with electrophoretic material systems

We have successfully demonstrated a control device for a viewing angle that enables switching between two states, a wide‐viewing angle, and a narrow‐viewing angle. It is composed of a light‐transmitting portion formed with an array of optical micro‐rods and a shielding/transmitting changeable portion of cross stripes designed with electrophoretic material systems consisting of black particles and an optically transparent medium. When the black particles are fully dispersed in the optically transparent medium, the cross stripe portion plays the role of a non‐transmitting material as the shielding portion in a similar manner to a conventional viewing angle control film. When the black particles are completely gathered electronically to one side in the optically transparent medium, in contrast, the cross stripe portion filled by the optically transparent medium can transmit incident light. These functions allow us to select electrically either of two modes between a limited viewing angle and a non‐limited viewing angle. The optical properties for the limited viewing angle mode were +/?30° of the visible angle and 50% of the transmittance, and the one for the non‐limited viewing mode was 58% of the transmittance. The response time from the narrow‐viewing angle to wide‐viewing angle was 1 s at 20 V of applied voltage.     

Low‐voltage and high‐transmittance blue‐phase liquid‐crystal device with slanted electrodes

Abstract— A low‐voltage (～10 V_rms) and high‐transmittance (～90%) polymer‐stabilized blue‐phase liquid‐crystal (BPLC) device with a slanted‐electrodes structure is proposed. Unlike the vertical‐field‐switching (VFS) mode in which oblique incident light and a vertical field are employed, the proposed device utilizes normal incident light and an oblique field. The slanted electrodes generate a strong and uniform oblique electric field, which contributes in obtaining low voltage and high transmittance. Moreover, no couple films or prism sheets are needed, which helps to enhance the optical efficiency and simplify of the device structure. This device has great potential application for emerging BPLC displays and photonic devices.     

Emission of dispersed‐type inorganic EL devices with frequency‐variable high‐voltage oscillation circuit

Dispersed‐type inorganic electroluminescent (EL) devices composed of a transparent electrode, a phosphor, a dielectric, and a back electrode were prepared under various conditions using a zinc sulfide (ZnS)‐based phosphor. Additionally, a voltage/frequency variable circuit was designed. A compact high‐voltage/frequency variable circuit including three modules for boosting, frequency conversion, and voltage conversion was designed. A 140 V_pp voltage and a frequency in the range of 270 Hz to 2.4 kHz can be controlled by this circuit. The emission has begun to be observed at a voltage about 60 V_pp and a frequency of 400 Hz, at a voltage about 40 V_pp and a frequency of 1.4 kHz, 2.4 kHz, respectively. The emission intensity increased with an increase in frequency; emission with a wavelength of 450 nm was strongly influenced by the frequency. The luminescence and the electrical properties were affected by the preparation conditions including device structures, dispersion of ZnS:Cu, and Cl particles because of the current path generated by defects in the EL cell.     

Lightweight electrowetting display on ultra‐thin glass substrate

Mobile display devices that use ultra‐thin (≤100 µm) glass substrates offer a combination of attractive characteristics: lightweight, high quality device fabrication process, thermal and dimensional stability, and mechanical flexibility. Electrowetting (EW) devices fabricated on ultra‐thin glass are demonstrated in this paper. Water contact angle, which is the most critical parameter of EW devices, changes from ~165° to 80° when a 20 V direct current (or alternating current) voltage is applied. EW devices on ultra‐thin glass show negligible hysteresis (~2°) and fast switching time of ~10 ms. EW device operation is maintained when the glass substrate is mechanically flexed. These results indicate the promise of narrow profile EW devices on ultra‐thin glass substrate for mobile and other devices, including video rate flexible electronic paper.     

High‐quality direct‐view display combining multiple integral 3D images

This paper proposes a method for combining multiple integral three‐dimensional (3D) images using direct‐view displays to obtain high‐quality results. A multi‐image combining optical system (MICOS) is used to enlarge and combine multiple integral 3D images without gaps. An optical design with a simple lens configuration that does not require a diffuser plate prevents the deterioration in resolution resulting from lens arrangement errors and the diffuser plate. An experiment was performed to compare a previously developed method with the proposed method, and the latter showed a significant improvement in image quality. A method for expanding the effective viewing angle of the proposed optical design was also developed, and its effectiveness was confirmed experimentally. A prototype device of the proposed optical design was constructed using a high‐density organic light‐emitting diode (OLED) panel with 8K resolution and 1058 ppi pixel density to achieve 311 (H) × 175 (V) elemental images, a viewing angle of 20.6° in both the horizontal and vertical directions, and a display size of 9.1 in. In addition, the proposed optical design enabled making device considerably thinner, ie, with a thickness of only 47 mm.     

Maximizing electro‐optic performances in the fringe‐field switching liquid crystal mode with negative dielectric anisotropic liquid crystal

The fringe‐field switching (FFS) mode that uses liquid crystals (LCs) with negative dielectric anisotropy is used in high‐resolution FFS liquid crystal display owing to its higher transmittance over positive LC, although its response time becomes slow and operating voltage (V_op) becomes high. In the device, reduction of the cell gap is required to achieve fast response time, which results in increase in V_op in general. In this paper, we propose the FFS mode with electrode width 1 µm and distance between the electrodes 1.5 µm. In such an electrode structure, V_op decreases with decreasing cell gap to 2 µm so that a proper V_op, high LC's light efficiency of 90%, a high color temperature, and a fast response time less than 10 ms, can be achieved, which maximizes electro‐optic performance of the FFS mode.     

Local dimming light‐guiding plate type backlight system using alignment‐controlled polymer‐dispersed liquid crystals

A new technology which enables a local brightness control according to the displayed images has been expected in the thin and lightweight backlight systems to improve a contrast ratio and power consumption of the liquid crystal displays (LCDs). In this paper, we have proposed a novel local‐dimming backlight system using alignment‐controlled polymer‐dispersed liquid crystals as a light‐guiding plate and investigated the forming conditions of polymer‐dispersed liquid crystals to achieve both a high‐luminance ratio and a fast response speed. As a result, we found that a luminance ratio and response speed of the backlight system can be improved by using bifunctional LC monomer materials and forming fine and rigid polymer network in the LCs, and achieved high luminance ratio of 16:1 and fast response time less than 0.5 ms. In addition, we fabricated the twisted nematic‐mode LCD using the local dimming light‐guiding plate‐type backlight based on this design, and successfully realized eight times higher contrast ratio than that of the traditional twisted nematic‐mode LCD.     

Simulation study of single‐cell‐gap transflective liquid crystal display with nonuniform potential

A single‐cell‐gap transflective liquid crystal display with a nonuniform electric potential is demonstrated. The top substrate has a top planar common electrode, a transparent dielectric layer with a general dielectric constant is coated on the bottom substrate, and two planar pixel electrodes with the same size are coated on the dielectric layer and the bottom substrate, respectively. With the different gaps between the two planar pixel electrodes and top planar pixel electrode, the nonuniform electric potential from the transmissive region (T region) to the reflective region (R region) is generated, while a bumpy reflector is coated under the bottom substrate. In this device, with the dielectric layer, the pixel and common electrodes generate a strong electric potential in the T region and a relatively weak electric potential in the R region. Consequently, the T and R regions accumulate the same optical phase retardation. The simulation results show that the display exhibits reasonably low operating voltage, high optical efficiency, and well‐matched voltage‐dependent transmittance and reflectance curves. Besides, the fabrication process and the driving mode of the transflective liquid crystal display are relatively simple, and it is suitable for mobile applications.     

Flexible thin‐film transistors application of amorphous tin oxide‐based semiconductors

The structural, optical, and electrical properties of Si‐doped SnO₂ (STO) films were investigated in terms of their potential applications for flexible electronic devices. All STO films were amorphous with an optical transmittance of ~90%. The optical band gap was widened as the Si content increased. The Hall mobility and carrier density were improved in the SnO₂ with 1 wt% Si film, which was attributed to the formation of donor states. Si (1 wt%) doped SnO₂ thin‐film transistor exhibited a good device performance and good stability with a saturation mobility of 6.38 cm²/Vs, a large I_on/I_off of 1.44 × 10⁷, and a SS value of 0.77 V/decade. The device mobility of a‐STO TFTs at different bending radius maintained still at a high level. These results suggest that a‐STO thin films are promising for fabricating flexible TFTs.     

A vertical structure photodetector based on all‐inorganic perovskite quantum dots

In this work, the vertical structure photodetector based on CsPbBr₃ quantum dots (QDs) with a structure of indium tin oxide (ITO)/zinc oxide (ZnO)/CsPbBr₃ QDs/Au is reported. In this device, CsPbBr₃ QDs film works as the light‐harvesting layer, and ZnO QDs film acts as the electron transport channel, which can extract the electron efficiently and improve the quality of CsPbBr₃ QDs film. As a result, the on/off ratio, detectivity and rise time (decay time) of CsPbBr₃/ZnO hybrid photodetector are measured to be 2.4 × 10⁶, 2.25 × 10¹¹, and 62 milliseconds (82 ms) under 0‐V bias. This work inspires the development of vertical structure photodetectors based on the all‐inorganic perovskite QDs.     

Liquid‐crystal mixtures having tolane substances for field‐sequential‐color TN‐LCDs

Novel liquid‐crystal (LC) mixtures featuring high optical anisotropy Δn) and small rotational viscosity (γ¹) were developed for field‐sequential‐color TN‐LCD applications. The dynamic behavior of the TN cells in a narrow‐gap range was studied and new tolane LC substances were introduced. The newly developed LC mixtures, having a narrow‐gap cell, enable a TN‐LCD to switch fast enough to be applied to field‐sequential‐color displays not only at a room temperature but also at low temperatures. It was also confirmed that the voltage‐holding ratio (VHR) is sufficiently high in field‐sequential addressing conditions and, therefore, the LC mixtures can be used in active‐matrix LCDs. For practical use, a storage test of the TN cells under light irradiation was performed to evaluate their voltage‐holding property. It was also confirmed that their high VHR can be maintained for over 10,000 hours under practical conditions.     

A fast transient LED driver with adaptive frequency control according to load variation for large‐sized LCD backlights

A fast transient light‐emitting diode (LED) driver is proposed for large‐sized liquid crystal display TV backlights in attempt to shorten the recovery time and to reduce the voltage fluctuation, while maintaining a high power efficiency. The direct current‐direct current (DC–DC) converter in the proposed LED driver accurately detects the load variation using the dimming data and then adjusts the slew rate and operating frequency according to the detected load variation. Thus, it rapidly controls the turn‐on time of the power switch and then controls the inductor current so that the output of the proposed LED driver can be accurately regulated during the load transient time. To verify the performance of the proposed LED driver, a DC–DC converter and an expandable LED current controller were fabricated using a 0.35‐μm bipolar–complementary metal–oxide–semiconductor (CMOS)–double‐diffused metal–oxide–semiconductor (DMOS) process technology and assembled with 48 LED channels for measurement. The measurement results show that the proposed LED driver improves the recovery time and voltage fluctuation by 45.1% and 45.6%, respectively. In addition, it achieves a maximum power of 115.2 W and a maximum power efficiency of 89.2%. Therefore, the proposed LED driver is suitable for high‐end applications such as large‐sized LED TV backlight modules.     

High resolution photolithography for direct view active matrix organic light‐emitting diode augmented reality displays

High‐resolution RGB organic light‐emitting diode frontplane is a key enabler for direct‐view transparent augmented reality displays. In this paper, we demonstrate 1250 ppi passive displays and semi‐transparent active displays. Organic light‐emitting diode photolithography can provide pixel density above 1000 ppi while keeping effective emission area high because of high aperture ratio. Patterns with 2 μm line pitch were successfully transferred to emission layers, indicating possible further pixel density scaling. Lifetime after patterning, key parameter enabling industrialization, is above 150 h (T90 at 1000 nit).     

A two-dimensional optical cross-connect with integrated waveguides and surface micromachined crossbar switches

The design, fabrication and test results of an all-optical cross-connect, which uses electrostatically actuated micromechanical digital mirrors to steer optical signals in a network of planar waveguides, are presented. The substrate consists of a network of spliced planar waveguides on silica substrates. The switches, located at the waveguide intersections, are formed with an electroplated T-structure consisting of a horizontal perforated square plate suspended by four elastic beams. When operated, the horizontal plate is pulled up making the mirror move out of the optical path thus steering the beam. An 8×8 switch array has been fabricated and tested. Actuation and relaxation switching times near 3 ms have been demonstrated with an actuation voltage of 120 V. The optical insertion loss for the array typically varied from 2.3 dB for a single trench in the optical path (shortest optical path) to 8 dB for 15 trenches in the optical path (longest optical path).