Effect of V2O5 Doping on the Sintering and Dielectric Properties of M-Phase Li1+x−yNb1−x−3yTix+4yO3 Ceramics

The effect of the addition of V₂O₅ on the structure, sintering and dielectric properties of M -phase (Li_{1+ x − y} Nb_{1− x −3 y} Ti _x +4 _y )O₃ ceramics has been investigated. Homogeneous substitution of V⁵⁺ for Nb⁵⁺ was obtained in LiNb_{0.6(1− x )}V_{0.6 x} Ti_0.5O₃ for x ≤ 0.02. The addition of V₂O₅ led to a large reduction in the sintering temperature and samples with x = 0.02 could be fully densified at 900°C. The substitution of vanadia had a relatively minor adverse effect on the microwave dielectric properties of the M -phase system and the x = 0.02 ceramics had [alt epsilon]_r= 66, Q × f = 3800 at 5.6 GHz, and τ_f= 11 ppm/°C. Preliminary investigations suggest that silver metallization does not diffuse into the V₂O₅-doped M -phase ceramics at 900°C, making these materials potential candidates for low-temperature cofired ceramic (LTCC) applications.     

Microwave Dielectric Properties of Li2TiO3 Ceramics Doped with ZnO–B2O3 Frit

A type of new low sintering temperature ceramic, Li₂TiO₃ ceramic, has been found. Although it is difficult for the Li₂TiO₃ compound to be sintered compactly at temperatures above 1000°C for the volatilization of Li₂O, dense Li₂TiO₃ ceramics were obtained by conventional solid-state reaction method at the sintering temperature of 900°C with the addition of ZnO–B₂O₃ frit. The sintering behavior and microwave dielectric properties of Li₂TiO₃ ceramics with less ZnO–B₂O₃ frit (≤3.0 wt%) doping were investigated. The addition of ZnO–B₂O₃ frit can lower the sintering temperature of the Li₂TiO₃ ceramics, but it does not apparently degrade the microwave dielectric properties of the Li₂TiO₃ ceramics. Typically, the good microwave dielectric properties of ɛ_r=23.06, Q × f =32 275 GHz, τ_f = 35.79 ppm/°C were obtained for 2.5 wt% ZnO–B₂O₃ frit-doped Li₂TiO₃ ceramics sintered at 900°C for 2 h. The porosity was 0.08%. The Li₂TiO₃ ceramic system may be a promising candidate for low-temperature cofired ceramics applications.     

Bismuth/Samarium Cosubstituted Ba6−3xNd8+2xTi18O54 Microwave Dielectric Ceramics

Modification of the microwave dielectric properties in Ba_{6−3 x} Nd_{8+2 x} Ti₁₈O₅₄ ( x = 0.5) solid solutions by Bi/Sm cosubstitution for Nd was investigated. A large increase in the dielectric constant and near-zero temperature coefficient combined with high Qf values were obtained in modified Ba_{6−3 x} Nd_{8+2 x} Ti₁₈O₅₄ solid solutions where an enlarged solid solution limit of Bi in Ba_{6−3 x} Nd_{8+2 x} Ti₁₈O₅₄ was observed. Excellent microwave dielectric characteristics (ɛ= 105, Qf = 4110 GHz, and very low τ_f) were achieved in the composition Ba_{6−3 x} (Nd_0.7Bi_0.18Sm_0.12)_{8+2 x} Ti₁₈O₅₄.     

Microwave Dielectric Properties of CaTiO3-CaAl1/2Nb1/2O3 Ceramics Doped with Li3NbO4

The microwave dielectric properties of CaTi_{1− x} (Al_1/2Nb_1/2) _x O₃ solid solutions (0.3 ≤ x ≤ 0.7) have been investigated. The sintered samples had perovskite structures similar to CaTiO₃. The substitution of Ti⁴⁺ by Al³⁺/Nb⁵⁺ improved the quality factor Q of the sintered specimens. A small addition of Li₃NbO₄ (about 1 wt%) was found to be very effective for lowering sintering temperature of ceramics from 1450–1500° to 1300°C. The composition with x = 0.5 sintered at 1300°C for 5 h revealed excellent dielectric properties, namely, a dielectric constant (ɛ_r) of 48, a Q × f value of 32 100 GHz, and a temperature coefficient of the resonant frequency (τ_f) of −2 ppm/K. Li₃NbO₄ as a sintering additive had no harmful influence on τ_f of ceramics.     

Improved Microwave Dielectric Properties of Ba6Ti1−xSnxNb4O18 Ceramics

Single-phase polycrystalline microwave dielectric ceramics Ba₆Ti_{1− x} Sn _x Nb₄O₁₈, with x changing from 0 to 1, were synthesized by the solid-state reaction method. All the solid solutions fitted well with A₆B₅O₁₈ cation-deficient hexagonal perovskite structure. The substitution of Sn for Ti effectively enhanced the quality factor and controlled τ_f. With increasing Sn content, the dielectric constant decreased from ∼47 to ∼32, and the Q × f value increased significantly from 11 530 to 28 496 GHz, with τ_f varying from 64 to 0 ppm/°C. A zero τ_f was realized when Sn was fully replaced by Ti with the composition Ba₆SnNb₄O₁₈.     

Electrical Properties of Sr0.7Ba0.3TiO3 Ceramics Doped with Nb2O5, 3Li2O · 2SiO2, and Bi2O3

The electrical properties of Sr_0.5Ba_0.3TiO₃ in the presence of Nb₂O₅ as a donor, 3Li₂O · 2SiO₂ as a sintering agent, and Bi₂O₃ as a dopant have been studied. When the compositions of the ceramics were 1 mol Sr_0.7Ba_0.3TiO₃+ 0.5 mol% Nb₂O₅+ 2 mol% 3Li₂O · 2SiO₂+ 0.2 mol% Bi₂O₃, the ceramics were sintered at 1100°C and exhibited the following characteristics: apparent dielectric constant ɛ, 25000; loss factor tan δ, 2%; insulating resistivity ρ_j, 10¹⁰Ω· cm; variation of dielectric constant with temperature Δɛ/ɛ (−25° to +85°C), +10%, −14%. ɛ and tan δ show only small changes with frequency. The study shows this ceramic can be used in multilayer technology.     

Low-Temperature Firing and Microwave Dielectric Properties of Ca[(Li1/3Nb2/3)0.84Ti0.16]O3−δ Ceramics for LTCC Applications

The effects of LiF and ZnO–B₂O₃–SiO₂ (ZBS) glass combined additives on phase composition, microstructures, and microwave dielectric properties of Ca[(Li_1/3Nb_2/3)_0.84Ti_0.16]O_3−δ (CLNT) ceramics were investigated. The LiF and ZBS glass combined additives lowered the sintering temperature of CLNT ceramics effectively from 1150° to 880°C. The main diffraction peaks of all the specimens split due to the coexistence of the non-stoichiometric phase (A) and stoichiometric phase (B), which all possess CaTiO₃-type perovskite structures. The transformation from A into B became accelerated with the increase of LiF or ZBS content. ZBS glass restrained the volatilization of lithium salt, which greatly affected the microstructures and microwave dielectric properties. CLNT ceramics with 2 wt% LiF and 3 wt% ZBS sintered at 900°C for 2 h show excellent dielectric properties: ɛ_r=34.3, Q × f =17 400 GHz, and τ_f=−4.6 ppm/°C. It is compatible with Ag electrodes, which makes it a promising ceramic for low-temperature cofired ceramics technology application.     

Ferroelectric and Piezoelectric Properties of Na1−xBaxNb1−xTixO3 Ceramics

Piezoelectric ceramics Na_{1− x} Ba _x Nb_{1− x} Ti _x O₃ with low BaTiO₃ concentrations x have been prepared by the solid-state reaction method, and their ferroelectric and piezoelectric properties have been studied. The ceramics are classic ferroelectrics when x ≤0.10, and the ferroelectric–paraelectric phase transition becomes diffusive when x ≥0.15. A low doping level of BaTiO₃ changes the NaNbO₃ ceramics from antiferroelectric to ferroelectric. With the increase in BaTiO₃ doping level, the Curie temperature of ceramics decreases linearly and the remnant polarization and coercive field also decrease, while their dielectric constant increases. Na_0.9Ba_0.1Nb_0.9Ti_0.1O₃ ceramics show the largest piezoelectric constant d ₃₃ (147 pC/N) and good sinterability, suggesting that it is a good candidate for lead-free piezoelectric ceramics.     

Microwave Dielectric Properties and Far-Infrared Reflectivity Characteristics of the CaTiO3–Li(1/2)−3xSm(1/2)+xTiO3Ceramics

Microwave dielectric properties and far-infrared reflectivity spectra of the 0.3CaTiO₃–0.7Li_{(1/2)−3 x} Sm_{(1/2)+ x} TiO₃ ceramics were investigated as a function of Sm³⁺ substitution (0.0 ≤ x ≤ 0.12). The dielectric constant decreased as the Sm³⁺ substitution increased. The Q × f value increased, up to a solid-solution limit at x = 0.11, because of the change of vibration modes between the A-site cation and the TiO₆ octahedron, and then decreased because of the formation of a secondary phase (Sm₂Ti₂O₇). On the analysis of the far-infrared reflectivity spectra, in the 50–4000 cm⁻¹ range, the change of the dielectric loss and dielectric constant could be explained by the intrinsic factor.     

Sintering and Microwave Dielectric Properties of the LiNb0.63Ti0.4625O3 Ceramics with the B2O3–SiO2 Liquid-Phase Additives

The effect of B₂O₃–SiO₂ liquid-phase additives on the sintering, microstructure, and microwave dielectric properties of LiNb_0.63Ti_0.4625O₃ ceramics was investigated. It was found that the sintering temperature could be lowered easily, and the densification and dielectric properties of LiNb_0.63Ti_0.4625O₃ ceramics could be greatly improved by adding a small amount of B₂O₃–SiO₂ solution additives. No secondary phase was observed for the ceramics with B₂O₃–SiO₂ additives. With the addition of 0.10 wt% B₂O₃–SiO₂, the ceramics sintered at 900°C showed favorable microwave dielectric properties with ɛ_r=71.7, Q × f =4950 GHz, and τ_f=−2.1 ppm/°C. The energy dispersive spectra analysis showed an excellent co-firing interfacial behavior between the LiNb_0.63Ti_0.4625O₃ ceramic and the Ag electrode. It indicated that LiNb_0.63Ti_0.4625O₃ ceramics with B₂O₃–SiO₂ solution additives have a number of potential applications on passive integrated devices based on the low-temperature co-fired ceramics technology.     

A- and B Site Cosubstituted Ba6−3xSm8+2xTi18O54Microwave Dielectric Ceramics

Tin (Sn) substitution into the B-site and Nd/Sn cosubstitution into the A- and B-sites were investigated in a Ba _{6−3 x} Sm_{8+2 x} Ti₁₈O₅₄solid solution ( x = 2/3). A small amount of tin substitution for titanium improved the temperature coefficient of resonant frequency (τ_f) but led to a decrease of the relative dielectric constant (ɛ) and the quality factor ( Qf ). The Ba_{6−3 x} Sm_{8+2 x} (Ti_{1− z} Sn_z)₁₈O₅₄-based tungsten-bronze phase became unstable for compositions with a tin content of ≥10 mol%, where BaSm₂O₄and Sm₂(Sn,Ti)₂O₇appeared, and finally, these phases became the major phases. On the other hand, Nd/Sn cosubstitution led to a good combination of high ɛ, high Qf , and near-zero τ_f. Excellent microwave dielectric properties were achieved in Ba_{6−3 x} (Sm_{1− y} Nd _y )_{8+2 x} (Ti_{1− z} Sn _z )₁₈O₅₄ceramics with y = 0.8 and z = 0.05 sintered at 1360°C for 3 h: ɛ= 82, Qf = 10 000 GHz, and calculated τ_f=+17 ppm/°C. The tolerance factor and electronegativity difference exhibited important effects on the microwave dielectric properties, especially the Qf value. A large tolerance factor and high electronegativity difference generally led to a higher Qf value.     

Subsolidus Phase Relationships in the Ga2O3–Al2O3–TiO2 System

Subsolidus phase relationships in the Ga₂O₃–Al₂O₃–TiO₂ system at 1400°C were studied using X-ray diffraction. Phases present in the pseudoternary system include TiO₂ (rutile), Ga_{2−2 x} Al_{2 x} O₃ ( x ≤0.78 β-gallia structure), Al_{2−2 y} Ga_{2 y} O₃ ( y ≤0.12 corundum structure), Ga_{2−2 x} Al_{2 x} TiO₅ (0≤ x ≤1 pseudobrookite structure), and several β-gallia rutile intergrowths that can be expressed as Ga_{4−4 x} Al_{4 x} Ti _{n −4}O_{2 n −2} ( x ≤0.3, 15≤ n ≤33). This study showed no evidence to confirm that aluminum substitution of gallium stabilizes the n =7 β-gallia–rutile intergrowth as has been mentioned in previous work.     

Subsolidus Phase Equilibria in the System Na2O-Bi2O3-TiO2 at 1000°C

Subsolidus phase relations in the system Na₂O-Bi₂O₃-TiO₂ at 1000°C were investigated by solid-state reaction techniques and X-ray diffraction methods. Five ternary compounds were observed in the system: Na_0.5Bi_4.5Ti₄O₁₅; Na_0.5Bi_0.5TiO₃; a cubic pyrochlore solid solution composed of xNa₂O.25Bi₂O₃.(75−;x) TiO₂ where x is 2.5 to 3.75; a new compound Na_0.5Bi_8.5Ti₇O₂₇ indexed with the orthorhombic cell of a = 5.45, b = 5.42, and c = 36.8 Å; and an unidentified phase with the probable composition NaBiTi₆O₁₄.     

Microwave Dielectric Properties of La6Mg4A2W2O24 [A=Ta and Nb] Ceramics

The microwave dielectric properties of two A-site-deficient perovskite-type ceramics in the La₆Mg₄A₂W₂O₂₄ [A=Ta and Nb] system were investigated. The compounds were synthesized by the solid-state ceramic route. The structure and microstructure were analyzed using X-ray diffraction and scanning electron microscopy techniques. The dielectric properties were measured in the microwave frequency range [4–6 GHz] by the resonance method. La₆Mg₄Ta₂W₂O₂₄ had Q _u× f =13 600 GHz, ɛ_r=25.2, and τ_f=−45 ppm/°C and La₆Mg₄Nb₂W₂O₂₄ had Q _u× f =16 400 GHz, ɛ_r=25.8, and τ_f=−56 ppm/°C.     

Microstructure–Dielectric Properties Relationship in Ba0.6Sr0.4TiO3–Mg2SiO4–Al2O3 Composite Ceramics

0.60Ba_0.6Sr_0.4TiO₃(BST)–(0.40− x )Mg₂SiO₄(MS)– x Al₂O₃ ( x =0, 0.5, 3, 5wt%) composite ceramics exhibit excellent characteristics suitable for tunable device applications. With increasing amount of Al, the dielectric peak can be quantitatively broadened and suppressed; the "phase transition temperature" T _c or ( T _m) shifts to a lower temperature. Meanwhile, the tunability is still high in a wider temperature range. Far from T _c, pyroelectric effects are observed by using the Byer and Roundy technology and Slim polarization hysteresis loops are observed under high ac dielectric field at 10Hz. These proved the existence of spontaneous polarization in certain possible orientations in a broad temperature range above T _c in the paraelectric medium and reveal why 0.60BST–(0.40− x )MS– x Al₂O₃ have such remarkable dielectric nonlinearity.     

Porous Glass-Ceramics with a Skeleton of the Fast-Lithium-Conducting Crystal Li1+xTi2−xAlx(PO4)3

Porous glass-ceramics with a skeleton of the fast-lithium-conducting crystal Li_{1+ x} Ti_{2− x} Al _x (PO₄)₃ (where x = 0.3–0.5) were prepared by crystallization of glasses in the Li₂O─CaO─TiO₂─Al₂O₃–P₂O₅ system and subsequent acid leaching of the resulting dense glass-ceramics composed of the interlocking of Li_{1+ x} Ti_{2− x} Al _x (PO₄)₃ and β-Ca₃(PO₄)₂ phases. The median pore diameter and surface area of the resulting porous Li_{1+ x} Ti_{2− x} Al _x (PO₄)₃ glass-ceramics were approximately 0.2 μm and 50 m²/g, respectively. The electrical conductivity of the porous glass-ceramics after heating in LiNO₃ aqueous solution was 8 × 10⁻⁵ S/cm at 300 K or 2 × 10⁻² S/cm at 600 K.     

A Novel Temperature-Compensated Microwave Dielectric (1−x)(Mg0.95Ni0.05)TiO3−xCa0.6La0.8/3TiO3 Ceramics System

The microstructure and microwave dielectric properties of a (1− x )(Mg_0.95Ni_0.05)TiO₃− x Ca_0.6La_0.8/3TiO₃ ceramics system have been investigated. The system was prepared using a conventional solid-state ceramic route. In order to produce a temperature-stable material, Ca_0.6La_0.8/3TiO₃ was added for a near-zero temperature coefficient (τ_f). With partial replacement of Mg²⁺ by Ni²⁺, the dielectric properties of the (1− x )(Mg_0.95Ni_0.05)TiO₃− x Ca_0.6La_0.8/3TiO₃ ceramics can be promoted. The microwave dielectric properties are strongly correlated with the sintering temperature and the composition. An excellent Q × f value of 118,000 GHz can be obtained for the system with x =0.9 at 1325°C. For practical application, a dielectric constant (ɛ_r) of 24.61, a Q × f value of 102,000 GHz, and a temperature coefficient of resonant frequency (τ_f) of −3.6 ppm/°C for 0.85(Mg_0.95Ni_0.05)TiO₃−0.15Ca_0.6La_0.8/3TiO₃ at 1325°C are proposed. A parallel-coupled line band-pass filter is designed and simulated using the proposed dielectric to study its performance.     

Contribution of Structure to Temperature Dependence of Resonant Frequency in the (1 −x)La(Zn1/2Ti1/2)O3·xATiO3 (A = Ca, Sr) System

The crystal structure and microwave dielectric properties of the (1 − x ) La(Zn_1/2Ti_1/2)O₃· x SrTiO₃ and (1 − x )La(Zn_1/2Ti_1/2)O₃· x CaTiO₃ system were investigated. X-ray powder diffraction showed that cation ordering disappeared at x > 0.3 for both systems. However, infrared spectra demonstrated that short-range cation ordering could exist at x = 0.4. Permittivity and the temperature coefficient of the resonant frequency (τ_f) of both systems exhibited nonmonotonic variations with composition. Both systems exhibited a τ_f of zero at the same composition of x = 0.5 although the τ_f of SrTiO₃ was about two times larger than that of CaTiO₃. The behavior of the permittivity and τ_f were described by the tilting of oxygen octahedra and cation ordering. The relation between τ_f and cation ordering of La(Zn_1/2Ti_1/2)O₃ was discussed in conjunction with the experimental results on metal halides. It is suggested that cation ordering induced a negative τ_f and suppressed the increase of permittivity for compositions between x = 0 to x = 0.5 for (1 − x )La(Zn_1/2Ti_1/2)O₃· x SrTiO₃ and (1 − x )La(Zn_1/2Ti_1/2)O₃· x CaTiO₃ systems.     

Effect of Li2CO3 Addition on the Sintering Temperature and Microwave Dielectric Properties of Mg2V2O7 Ceramics

Li₂CO₃ was added to Mg₂V₂O₇ ceramics in order to reduce the sintering temperature to below 900°C. At temperatures below 900°C, a liquid phase was formed during sintering, which assisted the densification of the specimens. The addition of Li₂CO₃ changed the crystal structure of Mg₂V₂O₇ ceramics from triclinic to monoclinic. The 6.0 mol% Li₂CO₃-added Mg₂V₂O₇ ceramic was well sintered at 800°C with a high density and good microwave dielectric properties of ɛ _r=8.2, Q × f =70 621 GHz, and τ_f=−35.2 ppm/°C. Silver did not react with the 6.0 mol% Li₂CO₃-added Mg₂V₂O₇ ceramic at 800°C. Therefore, this ceramic is a good candidate material in low-temperature co-fired ceramic multilayer devices.     

Low-Loss Microwave Dielectric Ceramics Using (Mg1−xMnx)2TiO4 (x=0.02–0.1) Solid Solution

Composite ceramics in a solid solution of (Mg_{1− x} Mn _x )₂TiO₄ ( x =0.02–0.1) have been prepared by the mixed oxide route. Formation of the solid solution was confirmed by the X-ray diffraction, the EDX analysis, and the measured lattice parameters, which varied linearly from Mg₂TiO₄ ( a = b = c =8.4410 Å) to (Mg_0.9 Mn_0.1)₂TiO₄ ( a = b = c =8.4445 Å). The XRD analysis also confirmed the co-existence of a cubic-structured (Mg_{1− x} Mn _x )₂TiO₄ and an ilmenite-structured second phase (Mg_{1− x} Mn _x )TiO₃. The composition expected to have a maximum Q × f (276 200 GHz at 10.5 GHz) is (Mg_0.95Mn_0.05)₂TiO₄ with ɛ_r∼15.69 and τ_f∼−52.6 ppm/°C. The existence of the second phase, however, would lead to no significant variation in the dielectric properties of the specimen because it possesses compatible properties compared with that of the main phase.