Structural, magnetic and electrical transport properties for a series of La1−xSrxFe1−xMnxO3 (0.3 ≤ x ≤ 0.7) compounds

The structural, electrical transport and magnetic properties have been studied for compounds: La_1−xSr_xFe_1−xMn_xO₃ (0.3 ≤ x ≤ 0.7). The lattice parameter, a, first decreases with x, and followed by an increase when Sr²⁺ and Mn⁴⁺ was continuously doped. The cell parameters, b and c, slightly decrease with coupled substitution of Sr²⁺ for La³⁺ and Mn⁴⁺ for Fe³⁺. In the paramagnetic temperature range, formation of magnetic clusters is suggested; the sizes of clusters decrease with x up to 0.5, following that they increase sharply with continuing doping. The electrical behaviors of all specimens demonstrate insulators and the electrical resistivity increases with content of Mn⁴⁺ and Sr²⁺ ions doped. A variable range hopping model is suitable to describe electrical transport process for the compounds at low temperature. At high temperature the electrical transport process can be described by bipolaron model for all compounds.     

Structural, magnetic and electrical properties of (La0.70−xNdx)Sr0.30Mn0.70Cr0.30O3 with 0 ≤ x ≤ 0.30

The structural, magnetic and electrical properties of (La_0.70−xNd_x)Sr_0.30Mn_0.70Cr_0.30O₃ perovskites (0 ≤ x ≤ 0.30) prepared by the usual ceramic procedure were investigated. Structural Rietveld refinement revealed that these compounds crystallize in a rhombohedral perovskite structure when x = 0, 0.10 and 0.20, while for x = 0.30 the structure becomes orthorhombic (Pbnm). It was found that the substitution of La by Nd reduces the Curie temperature (T_C). The FC, ZFC, M(H) and AC susceptibility measurements show typical canted-antiferromagnetism for the Nd-doped samples, in which a ferromagnetic component coexists with predominant antiferromagnetic interactions. The values of the magnetization (M(H)) decrease very slightly when increasing the Nd content, compared to the undoped sample (M_S values at 5 T and 2 K are, respectively, 47.9, 47.3 and 47.5 emu/g for x = 0.10, 0.20 and 0.30, compared to 48.2 emu/g for x = 0), indicating that the Nd³⁺ contribution is negligible compared to the total moment of the ferromagnetic (Mn/Cr) network. The resistivity increases by several orders of magnitude with Nd-doping and the semi-conducting behaviour persists in the whole temperature range. The interaction between Mn⁴⁺–O–Cr³⁺and Cr³⁺–O–Cr³⁺ is responsible for the semi-conducting state.     

Magnetic ordering and magnetic properties of ErAuxNi1−xIn (0 ≤ x ≤ 1) solid solution

The ErAu_xNi_1−xIn (0 ≤ x ≤ 1) quasiternary compounds crystallize in the hexagonal layered crystal structure of ZrNiAl-type. ErAuIn was reported to be an antiferromagnet with T_N = 3 K and magnetic moments having triangular arrangement within the basal plane (the magnetic order is described by the propagation vector ). On the contrary ErNiIn is a ferromagnet with T_C = 9 K and magnetic moments pointing along the c-axis. The magnetic ordering in ErAu_xNi_1−xIn (0 < x < 1) solid solution, has been investigated by neutron diffractometry in the temperature range between 1.5 and 15 K. Moreover, bulk magnetic measurements have been carried out in the range 1.72–400 K. All alloys of intermediate composition were found to be antiferromagnets with T_N between 4.6 and 7 K. Below 2 K their magnetic order is described by the propagation vector and magnetic moments are aligned along the c-axis. However, for alloys with 0.2 ≤ x ≤ 0.7 the propagation vector was found to turn into with increasing temperature.     

Hydrogenation of CaLi2−xMgx (0 ≤ x ≤ 2) with C14 Laves phase structure

CaLi_2−xMg_x (0 ≤ x ≤ 2) which has the C14-type Laves phase structure has been successfully synthesized and hydrogenated. The C14-type Laves phase structure was kept after hydrogenation of CaLi_2−xMg_x (x = 0.2, 0.5, 1). After hydrogenation of CaLi₂ and CaMg₂, the Laves phase disappeared. The CaH₂ and LiH phases were formed from CaLi₂ and the CaH₂ and Mg phases from CaMg₂, respectively. CaLi_2−xMg_x (0 < x < 2) ternary alloys formed stable hydride phases with the C14-type Laves phase structure in contrast to CaLi₂ and CaMg₂ binary alloys.     

Electrical behaviour of hydridofluorides of potassium–calcium KCaH3−xFx with x = 1, 1.5, 2, 2.5

This paper reports the results of the electrical conductivity measurements for KCaH_3−xF_x series with (x = 1, 1.5, 2, 2.5) in the temperature range 298–503 K.The activation energy of the electrical conductivity for the studied compounds depends on hydrogen amount and Reau's criteria. Differential thermal analysis curves were measured in the same temperature range 298–503 K.Possible correspondence between preferential order given by X-ray diffraction, thermal behaviour and electrical properties are discussed.     

Magnetic phase diagram of CrTe1−xSbx (0.0≤x≤1.0)

Measurements of the high field magnetization of CrTe_1−xSb_x (0.0≤x≤1.0) were carried out at 4.2 K in pulsed magnetic fields up to 300 kOe. The temperature dependence of the magnetization of CrTe_1−xSb_x was measured in the temperature range from 4.2 K to 800 K. The magnetic phase diagram of CrTe_1−xSb_x (0.0≤x≤1.0) was determined, which is similar to the typical one for the mixed crystals of the layered antiferromagnetic and ferromagnetic compounds proposed by de Gennes.     

The magnetic phase diagram of DyFe12−xMox (1.00≤x≤3.00)

The magnetocrystalline anisotropy and magnetic structure of DyFe_12−xMo_x (1.00≤x≤3.00) have been investigated in detail by X-ray diffraction, thermomagnetic analysis, AC magnetic susceptibility, singular point detection technique and angular-magnetization measurement. A magnetic phase diagram of DyFe_12−xMo_x (1.00≤x≤3.00) has been proposed. At room temperature, all DyFe_12−xMo_x compounds exhibit uniaxial anisotropy. At low temperature, a spin reorientation transition of axis-to-cone was observed for DyFe_12−xMo_x compounds with low Mo concentration, x<2.00. The spin reorientation temperature decreases with increasing Mo concentration. For DyFe_12−xMo_x compounds with high Mo concentration, magnetohistory effects were observed below 48 K.     

Influence of Co substitution on magnetoelastic properties of Er2Fe14−xCoxB (x = 1, 3 and 5) intermetallic compounds

The magnetostriction and thermal expansion of Er₂Fe_14−xCo_xB (x = 1, 3 and 5) intermetallic compounds were measured, using the strain gauge method in the temperature range 75–450 K under applied magnetic fields up to 1.5 T. For all samples the longitudinal magnetostriction (λ_l) undergoes an anomaly around the spin reorientation temperature (T_SR). It is also observed that λ_l decreases with increasing the Co content. All compounds show saturation type behaviour in their anisotropic magnetostriction curves at different temperatures and applied fields. The saturation behaviour of the compound with x = 3 occurs at higher temperatures than with x = 1 and 5. The volume magnetostriction strongly increases below μ₀H = 0.3 T, then monotonically rises with applied field up to the spin reorientation temperature. An invar type behaviour is observed above 200 K in the compound with x = 1. The results are discussed based on the temperature dependence of magnetocrystalline anisotropy of compounds below and above their T_SR.     

Dielectric and magnetic properties of 0.7Bi(Fe1−xCrx)O3–0.1BaTiO3–0.2PbTiO3 solid solutions

0.7Bi(Fe_1−xCr_x)O₃–0.1BaTiO₃–0.2PbTiO₃ (x = 0, 0.1, 0.2, 0.3) solid solutions were prepared by the traditional ceramic process. X-ray diffraction results revealed that the samples with x = 0–0.3 showed pure perovskite structure. Frequency and temperature dependences of dielectric constants and dielectric loss of the samples were investigated. Both dielectric constant and the loss tangent increased at given frequencies (100 Hz–1 MHz), while the Curie temperature of the solid solutions decreased with increasing Cr content. Room temperature magnetic hysteresis loops indicated that an appropriate amount of Cr could improve magnetization of the solid solutions.     

Study of ac impedance spectroscopy of Al doped MnFe2−2xAl2xO4

We have reported electrical properties of Al doped MnFe₂O₄ ferrite using ac impedance spectroscopy as a function of frequency (42 Hz to 5 MHz) at different temperatures (300–473 K). XRD analysis shows that all the compositions are single phase cubic spinel in structure. The complex impedance analysis has been used to separate the grain and grain boundary resistance of MnFe_2−2xAl_2xO₄. From the analysis of impedance spectra it is found that the real (Z′), and imaginary (Z″) part of the impedance decrease with increasing frequency and both are found to decrease with Al doping up to 20%, and thereafter, these increase with further increasing the Al concentration. Experimental results have been fitted with two parallel RC equivalent circuits in series.     

Self-propagating high-temperature synthesis with post-heat treatment of La1−xSrxFeO3 (x = 0–1) perovskite as catalyst for soot combustion

La_1−xSr_xFeO₃ (x = 0–1) perovskite, Sr-substituted LaFeO₃, was prepared by Self-propagating high-temperature synthesis (SHS) and its catalytic activity for soot combustion was experimentally examined in comparison with that of a conventional Pt/Al₂O₃ catalyst. The products were also characterized by XRD, FE-SEM, and BET specific surface area. The XRD analysis revealed that all the products had a perovskite phase as the major compound, together with intermediate phases with higher x values (x = 0.7–1). The BET specific surface area of the products increased with x. Moreover, the catalytic activity for soot combustion also increased with x, wherein the BET specific surface area appeared an appropriate index for explaining the observed activity. The sample with x = 0.8 exhibited the highest activity for soot combustion among all the SHS products. The soot combustion temperature of this product was as much as 100 °C lower than that of non-catalytic soot combustion. In other words, it had the same activity as that at only 20 °C higher, in comparison to conventional Pt/Al₂O₃ catalyst. More significantly, average apparent activation energy of sample with x = 0.8 calculated by Friedman method using TG/DTA was approximately 15 kJ/mol lower than that of Pt/Al₂O₃ catalyst. This result suggested that La_1−xSr_xFeO₃ has the possibility to be an alternative catalyst to Pt/Al₂O₃ catalyst.     

Investigation of the dependency of the upper critical magnetic field on the content x in Y1−xYbx/2Gdx/2Ba2Cu3O7−y superconducting structures

The Y_1−xYb_x/2Gd_x/2Ba₂Cu₃O_7−y superconducting samples for x = 0.0, 0.2, 0.4, 0.6, 0.8 and 1.0 were prepared by using the solid-state reaction technique. Resistivity measurements of the samples were performed in QD–PPMS system under different magnetic fields up to 5 T in zero fields cooling regime. Using the resistivity data, the upper critical magnetic field H_c2(0) at T = 0 K for 50% of R_n was calculated by the extrapolation H_c2(T) to the temperature T = 0 K. The coherence length in T = 0 K were calculated from H_c2(0) and the effects of x in the composition on both the coherence length and the upper critical magnetic field were examined. The results showed that H_c2(0) varied from 84.05 to 122.26 T with the content x. The upper critical magnetic field in the temperature T = 0 K slightly decreased with increasing the content x. Using the content x, the upper critical magnetic field can be controlled and this can be used in the superconductivity applications.     

Study of the electrical conduction behaviour of the Ba1−xLaxTi1−xNixO3 (x 0.10) system

The electrical conduction behaviour of the Ba_1−xLa_xTi_1−xNi_xO₃ (x 0.10) system has been studied by complex plane impedance analysis and measurements of a.c. conductivity in the temperature range 400–575 K. The values of the bulk resistance for these samples are obtained from a circular arc passing through the origin in their impedance plots. A.c. conductivity obeys the relation σ_a.c.αω⁸ in the temperature range of measurements. These results indicate that conduction occurs in this system because of hopping of charge carriers between localized nickel sites.     

Investigation of hydrogen absorption/desorption properties of ZrMn0.85−xFe1+x alloys

The crystal structures and hydrogen absorption/desorption properties of the ZrMn_0.85−xFe_1+x alloys (x = 0, 0.2, 0.4) were investigated systematically. The pressure–composition (PC) isotherms and absorption kinetics were measured at 273–333 K by the volumetric method. Besides the crystal structure, the plateau pressure and the hydrogen intake capacity, this article also discussed the absorption kinetics, the pulverization resistance and the thermodynamic properties. XRD patterns revealed that ZrMn_0.85Fe and ZrMn_0.65Fe_1.2 were formed as hexagonal C14 laves phase structure while ZrMn_0.45Fe_1.4 possessed cubic C15 laves phase structure. With the increase of Fe and decrease of Mn, the plateau pressure increased while the hydrogen intake capacity lowered and the hydrogen absorption kinetics degraded. On the other hand, the hysteresis alleviated, the pulverization resistance improved and the stability of the hydrides decreased. The decomposition pressure was increased to more than 160 times for ZrMn_0.85Fe and more than 2500 times for ZrMn_0.65Fe_1.2 compared with that of the ZrMn₂ alloy.     

Thermoelectric properties of hot-pressed Zn4Sb3−xTex

A series of samples have been fabricated through vacuum melting method followed by hot-pressing for Zn₄Sb_3−xTe_x (x = 0.02–0.08), XRD patterns indicated that all the samples were single-phased β-Zn₄Sb₃. Electrical conductivity and Seebeck coefficient were evaluated in the temperature range of 300–700 K, showing p-type conduction. The thermoelectric figure of merit (ZT) was increased with the increase of Te content. ZT values of 0.8 and 1.0 were obtained at 673 K for Zn_4.08Sb₃ and Zn₄Sb_2.92Te_0.08, respectively.     

Thermoelectric properties of Sn1−x−yTiySbxO2 ceramics

Thermoelectric properties of Sn_1−x−yTi_y Sb_xO₂ ceramics were investigated in detail. The addition of Sb into SnO₂ matrix increased the electric conductivity, σ. The increase in the σ value should be caused by the increase in the carrier concentration. The Seebeck coefficients of all the samples were negative, which means that these samples have n-type conduction. The samples of this study have porous structure. The maximum Z value of all the samples measured in this study was 2.4 × 10⁻⁵ K⁻¹.     

Effect of Yb substitution on microstructure, physical and mechanical properties of negative thermal expansion Zr1−xYbxWMoO8−x/2 (x = 0–0.05) ceramic

Cubic Zr_1−xYb_xWMoO_8−x/2 (x = 0–0.05) ceramic was first fabricated by a polymorphous precursor transition method. X-ray diffraction experiment indicates that samples with x ≤ 0.05 are single phase solid solution. The measured bulk density, microstructure, maximal compression strength and Young's modulus are obviously sensitive to Yb substitution level, while none of such sensitivity was found for the lattice parameters, negative thermal expansion coefficients and Vickers hardness. Drilling tests on Zr_0.96Yb_0.04WMoO_7.98 ceramic indicate good machinability, which is often required for quality and shape control in engineering applications.     

Monoclinic phases and stress-relief conditions in (1 − x)Pb(Mg1/3Nb2/3)TiO3–xPbTiO3 solid solutions

A comparative study on heterophase states in perovskite-type solid solutions of (1 − x)Pb(Mg_1/3Nb_2/3)TiO₃–xPbTiO₃ is carried out for compositions near the morphotropic phase boundary. The conditions for mechanical stress relief at elastic matching of phases are analysed at x = const in a wide temperature range. The heterophase states concerned with the presence of the intermediate monoclinic phase are interpreted using the domain state–interface diagrams calculated for x = 0.28, 0.32 and 0.34. It is shown that optimum volume fraction parameters of the domains in the monoclinic phase of the B type are varied in relatively wide ranges and promote complete stress relief with cubic–monoclinic phase coexistence. Two scenarios of stress relief at x = 0.32 are considered in connection with different heterophase states (either tetragonal–monoclinic of the B type or tetragonal–monoclinic of the C type) in a wide temperature range. Possibilities of elastic matching of two polydomain phases (tetragonal–monoclinic of the B type) with almost equal relative widths of the domains in these phases are shown for x = 0.34. The active role of domains of the monoclinic phases in stress relief and forming the planar unstrained interfaces is discussed.     

Martensitic transformation and anomalies in resistivity of (Ti–50Ni)1−xCx (x = 0.1, 0.5 at.%) shape memory alloys

Phase transformation of solid solution (Ti–50Ni)_1−xC_x (x = 0.1, 0.5 at.%) alloys have been studied by using differential scanning calorimetry, physical property measurement system and optical microscope. The transformation temperature decreases due to the existence of titanium carbide (TiC) particles compared with that of near-equiatomic Ti–Ni shape memory alloy. The resistivity vs. temperature curves show hysteresis. Thermoelastic martensitic transformation occurred in two alloys despite the difference in TiC content. Nevertheless, the resistivity results show different martensitic transformation routes. A one-step B2 → B19′ transformation occurred in the low TiC content alloy and an R transformation appeared in another alloy, suggesting that the martensitic transformation routes depended on the TiC content. The cumulative effect of the TiC particles causes the local stress field and lattice distortion to restrain the transformation of the B19′. On the other hand, the TiC content has an effect on the temperature coefficient of electrical resistivity (TCR) of alloys. The Ti–Ni–0.5C alloy shows a negative TCR in the range 100–300 K during which transformation occurs. Another alloy shows the opposite result. The cause of the negative TCR is briefly discussed.     

Studies on structural and thermal expansion properties of Ho2−xLnxMo4O15 (Ln = Er, Sm and Ce) solid solutions

Three new series of Ho_2−xEr_xMo₄O₁₅ (x = 0.0–2.0), Ho_2−xSm_xMo₄O₁₅ (x = 0.0–0.6) and Ho_2−xCe_xMo₄O₁₅ (x = 0.0–0.25) solid solutions have been prepared successfully by solid-state reaction and studied by powder X-ray diffraction. All the XRD patterns of these molybdates can be indexed in monoclinic space group P2₁/c. Lattice parameters a, b and c of Ho_2−xLn_xMo₄O₁₅ decrease linearly with increasing erbium content and increase with increasing samarium or cerium content. Thermal expansion behaviors of Ho_2−xLn_xMo₄O₁₅ have been investigated in the 25–500 °C temperature range with high-temperature X-ray diffraction. The temperature dependence of Mo(2)–O14 interaction looks like to be responsible for their thermal expansion behaviors.