Elaboration of Poly(ε‐caprolactone)‐g‐TiNbO5 Nanocomposites via in situ Metal Complex Initiated Intercalative Polymerization

Summary: The preparation of poly(ε‐caprolactone)‐g‐TiNbO₅ nanocomposites via in situ intercalative polymerization of ε‐caprolactone initiated by an aluminium complex is described. These nanocomposites were obtained in the presence of HTiNbO₅ mineral pre‐treated by AlMe₃, but non‐modified by tetraalkylammonium cations. These hybrid materials obtained have been characterized by Fourier transform infrared absorption spectroscopy, wide‐angle X‐ray scattering, scanning electron microscopy, and dynamic mechanical analysis. Layered structure delamination and homogeneous distribution of mineral lamellae in the poly(ε‐caprolactone) (PCL) is figured out and strong improvement of the mechanical properties achieved. The storage modulus of the nanocomposites is enhanced as compared to pure PCL and increases monotonously with the amount of the filler in the range 3 to 10 wt.‐%.

SEM image of the fractured surface of a PCL‐TiNbO₅ nanocomposite film.     

Biodegradable polyester layered silicate nanocomposites based on poly(ϵ‐caprolactone)

Nanocomposites based on biodegradable poly(?‐caprolactone) (PCL) and layered silicates (montmorillonite, MMT) were prepared either by melt interaction with PCL or by in situ ring‐opening polymerization of ?‐caprolactone as promoted by the so‐called coordination‐insertion mechanism. Both non‐modified clays (Na⁺ ‐MMT) and silicates modified by various alkylammonium cations were studied. Mechanical and thermal properties were examined by tensile testing and thermogravimetric analysis. Even at a filler content as low as 3 wt% of inorganic layered silicate, the PCL‐layered silicate nanocomposites exhibited improved mechanical properties (higher Young's modulus) and increased thermal stability as well as enhanced flame retardant characteristics as a result of a charring effect. It was shown that the formation of PCL‐based nanocomposites depended not only on the nature of the ammonium cation and related functionality but also on the selected synthetic route, melt intercalation vs. in situ intercalative polymerization. Interestingly enough, when the intercalative polymerization of ?‐caprolactone was carried out in the presence of MMT organo‐modified with ammonium cations bearing hydroxyl functions, nanocomposites with much improved mechanical properties were recovered. Those hybrid polyester layered silicate nanocomposites were characterized by a covalent bonding between the polyester chains and the clay organo‐surface as a result of the polymerization mechanism, which was actually initiated from the surface hydroxyl functions adequately activated by selected tin (II) or tin (IV) catalysts.     

Synthesis and Properties of some ε‐Caprolactone‐Based Di‐ and Triblock Polymers by Anionic Polymerization

Block copolymers containing ε‐caprolactone were synthesized. Mechanical properties as a function of chemical composition and domain structure as a function of elongation were studied. Based on previous optimal conditions determination by factorial design of experiments of ε‐caprolactone anionic polymerization, polystyrene‐block‐poly(ε‐caprolactone), polyisoprene‐block‐poly(ε‐caprolactone), polystyrene‐block‐polybutadiene‐block‐poly(ε‐caprolactone) (SBCL), and polystyrene‐block‐polyisoprene‐block‐poly(ε‐caprolactone) (SICL) with different compositions where synthesized, and characterized by GPC and DSC. Both the SICL and SBCL materials are thermoplastic elastomers, from which spin‐cast films were prepared. Their mechanical properties were determined, small angle X‐ray scattering (SAXS) measurements were carried out during straining, and dynamic mechanical analysis (DMA) was performed. All diblock polymers separate into a two‐phase structure, but the melting point of crystalline poly(ε‐caprolactone) domains in the block polymer is higher than in the case of the homopolymer. According to DMA data, some of the SICL and SBCL materials are three‐phase systems, but others are only two‐phase systems. The two‐phase materials show a considerable depression of the composite hard domain glass transition and, consequently, turn out to be very soft. It appears peculiar that the transition from three‐phase to two‐phase material is accomplished by decreasing the soft block length. For the soft material SAXS exhibits a lamellar stack nanoscale structure and several reflections of colloidal crystals. As a function of increasing elongation, the crystal reflections broaden, whereas lamellar stacks rotate as a whole.     

Preparation and characterization of poly(ϵ‐caprolactone‐co‐p‐dioxanone)–poly(ethylene glycol)–poly(ϵ‐caprolactone‐co‐p‐dioxanone)/bioactive inorganic particle nanocomposites

With an aim to develop injectable hydrogel with improved solution stability and enhanced bone repair function, thermogelling poly(ε‐caprolactone‐co‐p‐dioxanone)‐poly(ethylene glycol)‐poly(ε‐caprolactone–co‐p‐dioxanone) (PECP)/bioactive inorganic particle nanocomposites were successfully prepared by blending the triblock copolymer (PECP) with nano‐hydroxyapatite (n‐HA) or nano‐calcium carbonate (n‐CaCO₃). The hydrogel nanocomposites underwent clear sol–gel transitions with increasing temperature from 0 to 50°C. The obtained hydrogel nanocomposites were investigated by ¹H NMR, FT‐IR, TEM, and DSC. It was found that the incorporation of inorganic nanoparticles into PECP matrix would lead to the critical gelation temperature (CGT) shifting to lower values compared with the pure PECP hydrogel. The CGT of the hydrogel nanocomposites could be effectively controlled by adjusting PECP concentration or the content of inorganic nanoparticles. The SEM results showed that the interconnected porous structures of hydrogel nanocomposites were potentially useful as injectable scaffolds. In addition, due to the relatively low crystallinity of PECP triblock copolymer, the aqueous solutions of the nanocomposites could be stored at low temperature (5°C) without crystallization for several days, which would facilitate the practical applications. The PECP/bioactive inorganic particle hydrogel nanocomposites are expected to be promising injectable tissue engineering materials for bone repair applications. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Improving the barrier character of polylactide/phenoxy immiscible blend using poly(lactide‐co‐ɛ‐caprolactone) block copolymer as a compatibilizer

The improvement of the barrier character of polylactide by the addition of poly(hydroxy ether) of bisphenol A (Phenoxy) and poly(lactide‐co ‐?‐caprolactone) copolymer that acts as a compatibilizer is studied. First, differential scanning calorimetry, Fourier transformed infrared spectroscopy, and scanning electron microscopy show that the addition of the copolymer allows to obtain a miscible ternary system. The permeability of polylactide to water vapor, oxygen, and carbon dioxide is enhanced with the addition of phenoxy but better improvement in its barrier character is obtained with the addition of the compatibilizer. The effects of different factors such as miscibility, glass transition temperature, and crystallinity on the transport properties are analyzed. Several permeability prediction models for heterogeneous systems have been applied obtaining quite good results for water vapor and oxygen permeability. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45396.     

Thermo‐oxidative stabilization of poly(lactic acid)‐based nanocomposites through the incorporation of clay with in‐built antioxidant activity

In this work, an innovative approach to overcome the issue of the poor thermo‐oxidative stability of polymer/clay nanocomposites is proposed. Specifically, biodegradable poly(lactic acid) (PLA)‐based nanocomposites, containing organo‐modified clay with in‐built antioxidant activity, were prepared. Through a two‐step chemical protocol, a hindered phenol antioxidant was chemically linked to the ammonium quaternary salt which was then intercalated between the clay platelets [(AO)OM‐Mt]. The nanocomposites were characterized and their thermo‐oxidative stability during melt processing and under long‐term thermal test conditions was investigated. PLA nanocomposites containing the (AO)OM‐Mt showed higher oxidative stability, along with better clay dispersion, compared to PLA‐nanocomposites containing commercial clay and a free hindered phenol antioxidant. Obtained results can be explained considering that (AO)OM‐Mt may act locally, at the interface, between the silicate layers and the polymer macromolecules, thus contributing to the observed improved stability of the polymer both during processing and under long‐term thermal‐oxidative conditions. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44974.     

Poly(ɛ‐caprolactone) nanocomposites with layered double hydroxides modified by in situ grafting polymerization: Structure characterization and barrier properties

The synthesis of multimetallic layered double hydroxides‐g ‐poly(?‐caprolactone) (LDHs‐g ‐PCL) was explored by in situ ring‐opening polymerization, considering layered clay's improvement on barrier properties in polymer films. LDHs/PCL nanocomposites were prepared by blending LDHs‐g ‐PCL and pure PCL via solution casting method. With incorporation of as low as 0.2 wt % of LDHs, LDHs/PCL nanocomposites exhibited excellent mechanical performance with tensile strength and elongation at break over 45 MPa and 837%, respectively. Compared with pure PCL, the O₂ permeability of LDHs/PCL nanocomposites decreased by nearly 78% as LDHs content increased up to 1 wt %. It was revealed that the key parameter to improve the barrier properties is not only the high aspect ratio of layered clays but also the specific interactions that they develop in the polymers matrix. Due to the merits of its biodegradation and physical properties, LDHs/PCL nanocomposites could be potential materials applied in packaging industry widely. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45320.     

Studies on transport of vapor and solute molecules through polyvinyl alcohol‐based clay containing nanocomposites

The present study focuses on fabricating of polymer–clay nanocomposites by in situ polymerization method and investigating their permeability behavior toward vapor and liquid molecules, thus, to evaluating barrier properties of the nanocomposites. For this purpose, acrylonitrile (AN) monomer was grafted on to poly(vinyl alcohol) (PVA) chains after the addition of very low amount of fuller's earth (clay) into polymer matrix using a suitable initiator, such as potassium persulphate (KPS), and crosslinker N‐N′ methylene bisacrylamide (MBA). The prepared nanomaterials were characterized by Fourier‐Transformation infrared (FTIR) spectroscopy and wide‐angle X‐ray diffraction (WXRD) techniques. The morphological features of designed materials were studied by scanning electron microscopy. The graft materials impregnated with fuller's earth were examined for their permeability behavior by observing the permeation of solute and vapor molecules from aqueous dye solution and volatile organic solvent, respectively. The composition of the nanocomposites and the amount of fuller's earth content were found to affect the passage of solute and vapor molecules across the nanocomposite membrane. The permeation capacity was quantified by evaluating permeability parameters. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Composites Between Alumina and an Ester‐Ether‐Ester Bioresorbable Copolymer

Composites between alumina and the bioresorbable poly(ε‐caprolactone)‐block‐poly(oxyethylene)‐block‐poly(ε‐caprolactone) copolymer were obtained by reacting ε‐caprolactone with preformed poly(ethylene glycol), in the presence of ceramic alumina powder, at 185°C under vacuum. The mechanical properties, tested by compression and flexural strengths and Young's modulus, show that the copolymer interacts poorly with the alumina grains. Both scanning electron and atomic force microscopy show a scarce wettability between alumina and copolymer, as well as the aggregation of alumina micro‐particles into clusters of big size. Both mechanical and morphological tests seem to indicate a stronger interaction between the alumina micro‐particles than between the alumina surface and the reaction mixture during the polymerization, as well as a “compacting effect” by alumina on the forming copolymer. The FT‐IR spectra of the composites show both copolymer and alumina absorption bands. The FT‐IR analysis on the fractions of an extraction with CHCl₃ indicates the presence of traces of poly(ε‐caprolactone), stably linked to alumina. The polymerization of ε‐caprolactone with alumina alone in the same conditions gives poly(ε‐caprolactone), mainly free and in minor part linked to the alumina surface. Two polymerization mechanisms, simultaneously occurring, are proposed. The most relevant result of this work is the lack of chemical inertness of alumina towards ε‐caprolactone, which leads to reconsider also the use of alumina as a biochemically inert material.     

Anomalous impact strength for layered double hydroxide‐palmitate/poly(ε‐caprolactone) nanocomposites

Inherent physical properties and commercial availability makes poly(ε‐caprolactone) (PCL) very attractive as a potential substitute material for nondegradable polymers for commodity applications. However, a balance of toughness and stiffness is needed in order to transfer this potential into reality, particularly for short‐term packaging applications. In this context, layered double hydroxide modified with palmitic acid (LDH‐palmitate), was used as a nanoadditive to enhance the mechanical properties of PCL. Composites from PCL were prepared by melt‐blending with LDH‐palmitate loadings in the 1?10 wt % range. Scanning electron microscopy, transmission electron microscopy, and X‐ray diffraction were used to study the structure and morphology of the composites. The results showed homogeneous dispersion of clay particles in composites, but the degree of stacking of clay platelets was related to the LDH‐palmitate loadings. Charpy impact test measurements revealed an anomalous toughness improvement in the case of composite containing 5 wt % LDH‐palmitate, attributed to a combination of microcavitation and changes in crystallite sizes in the composite. The addition of LDH‐palmitate improved the water vapor barrier permeation of neat PCL film. In summary, LDH‐palmitate was shown to have potential as a nanoadditive to obtain tougher LDH‐PCL composite with improved barrier property. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41109.     

Polyethylene‐block‐poly(ε‐caprolactone) diblock copolymers: synthesis and compatibility

A strategy is introduced for the synthesis of polyethylene‐block‐poly(ε‐caprolactone) block copolymers by a combination of coordination polymerization and ring‐opening polymerization. First, end‐hydroxylated polyethylene (PE‐OH) was prepared with a one‐step process through ethylene/3‐buten‐1‐ol copolymerization catalyzed by a vanadium(III) complex bearing a bidentate [N,O] ligand ([PhN?C(CH₃)CHC(Ph)O]VCl₂(THF)₂). The PE‐OH was then used as macroinitiator for ring‐opening polymerization of ε‐caprolactone, leading to the desired nonpolar/polar diblock copolymers. The block structure was confirmed by spectral analysis using ¹H NMR, gel permeation chromatography and differential scanning calorimetry. The unusual topologies of the model copolymers will establish a fundamental understanding for structure–property correlations, e.g. compatibilization, of polymer blends and surface and interface modification of other polymers. © 2014 Society of Chemical Industry     

Properties and degradation behavior of surface functionalized MWCNT/poly(L‐lactide‐co‐ε‐caprolactone) biodegradable nanocomposites

In this research, poly(L ‐lactide‐co‐ε‐caprolactone) (PLACL) reinforced with well‐dispersed multiwalled carbon nanotubes (MWCNTs) nanocomposites were prepared by oxidization and functionalization of the MWCNT surfaces using oligomeric L ‐lactide (LA) and ε‐caprolactone (CL). It is found that the surface functionalization can effectively improve the dispersion and adhesion of MWCNTs in PLACL. The surface functionalization will have a significant effect on the physical, thermomechanical, and degradation properties of MWCNT/PLACL composites. The tensile modulus, yield stress, tensile strength, and elongation at break of composite increased 49%, 60%, 70%, and 94%, respectively, when the concentration of functionalized MWCNTs in composite is 2 wt %. The in vitro degradation rate of nanocomposites in phosphate buffer solution increased about 100%. The glass transition temperature (T_g) of composites was decreased when the concentration of functionalized MWCNTs is 0.5 wt %. With further increasing the concentration of functionalized MWCNTs, the T_g was increased. The degradation kinetics of nanocomposites can be engineered and functionalized by varying the contents of pristine or functionalized MWCNTs. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis of poly(ε‐caprolactone)/clay nanocomposites using polyhedral oligomeric silsesquioxane surfactants as organic modifier and initiator

Poly(ε‐caprolactone)/clay nanocomposites were synthesized by in situ ring‐opening polymerization of ε‐caprolactone in the presence of montmorillonite modified by hydroxyl functionalized, quaternized polyhedral oligomeric silsesquioxane (POSS) surfactants. The octa(3‐chloropropyl) polyhedral oligomeric silsesquioxane was prepared by hydrolytic condensation of 3‐chloropropyltrimethoxysilane, which was subsequently quaternized with 2‐dimethylaminoethanol. Montmorillonite was modified with the quaternized surfactants by cation exchange reaction. Bulk polymerization of ε‐caprolactone was conducted at 110°C using stannous octoate as an initiator/catalyst. Nanocomposites were analyzed by X‐ray diffraction, transmission electron microscopy, thermo gravimetric analysis, and differential scanning calorimetry. Hydroxyl functionalized POSS was employed as a surface modifier for clay which gives stable clay separation for its 3‐D structure and also facilitates the miscibility of polymer with clay in the nanocomposites due to the star architecture. An improvement in the thermal stability of PCL was observed even at 1 wt % of clay loading. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Location of a nanoclay at the interface in an immiscible poly(ε‐caprolactone)/poly(ethylene oxide) blend and its effect on the compatibility of the components

Nanocomposites based on 80/20 and 20/80 (w/w) poly(ε‐caprolactone) (PCL)/poly(ethylene oxide) (PEO) immiscible blends and organophilic layered silicates were prepared with melt extrusion. From transmission electron microscopy analysis, it was observed that the exfoliated silicate platelets were preferentially located at the interface between the two blend phases. When the blend‐based nanocomposites were prepared via a two‐step process in which the silicates were first premixed with the PEO component or with the PCL component, the silicate layers migrated from the PEO phase or PCL phase to the interface. The rheological behavior of the nanocomposites was also investigated. At low frequencies, the frequency dependence of the storage modulus changed from a liquidlike behavior for the unfilled blend to a solidlike behavior for the nanocomposites, indicating the formation of a network structure as a result of exfoliation. From the scanning electron micrographs, a monotonic decrease of the PEO domain size in the 80/20 PCL/PEO blend was observed as a function of the organophilic clay content. Therefore, a clear emulsifying effect was induced by the organophilic layered silicates in the immiscible PCL/PEO blend. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Elongational rheology of biodegradable poly(lactic acid)/poly[(butylene succinate)‐co‐adipate] binary blends and poly(lactic acid)/poly[(butylene succinate)‐co‐adipate]/clay ternary nanocomposites

A series of blends based on poly(lactic acid) (PLA) and poly[(butylene succinate)‐co‐adipate] (PBSA) as well as their nanocomposites with nanoclay (PLA/PBSA/Clay ternary nanocomposites) were prepared using the twin‐screw extruder. The blends were prepared for PBSA contents ranging from 25 to 75 wt % and their corresponding nanocomposites were prepared at a single‐clay concentration. The morphology and structure of the blends and the nanocomposites were examined using field emission scanning electron microscopy, transmission electron microscopy, and X‐ray diffraction. Rheological properties (dynamic oscillatory shear measurements and elongational viscosities) of the blends, nanocomposites, and pure components were studied in detail. The strain hardening intensity of different blends and nanocomposites was compared with the behavior of the pure components. Strong strain hardening behavior was observed for blends composed of 50 wt % and higher PBSA content. However, the effect of PBSA content on the elongational viscosity was less pronounced in PLA/PBSA/Clay ternary nanocomposites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Six‐arm star‐shaped polymer with cyclophosphazene core and poly(ε‐caprolactone) arms as modifier of epoxy thermosets

A six‐arm star‐shaped poly(ε‐caprolactone) (s‐PCL) based on cyclophosphazene core was obtained by presynthesis of a hydroxy‐teminated cyclophosphazene derivative and subsequent initiation of the ring‐opening polymerization of ε‐caprolactone, and its use in different proportions as toughening modifier of diglycidylether of bisphenol A/anhydride thermosets was studied. The star‐shaped polymer was characterized to have approximately 30 caprolactone units per arm. Differential scanning calorimetry revealed a nonsignificant influence on the curing process of the epoxy‐anhydride formulation by the addition of s‐PCL. The s‐PCL‐modified epoxy thermosets exhibited a great improvement in both toughness and strength compared with the neat resin, as the result of a joint effort by the internal rigid core and the external ductile polyester chains of s‐PCL. When the addition of the modifier was 3 wt %, an optimal mechanical and thermomechanical performance was achieved. The impact resistance and tensile strength of the cured epoxy resin were enhanced by 150% and 30%, respectively. The glass transition temperature was also increased slightly. Moreover, the addition of the star‐shaped modifier had little harmful effect on the thermal stability of the material. Thus s‐PCL was proved to be a superior toughening agent without sacrificing thermal and mechanical properties of the thermosets. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44384.     

Unsaturated polyester–poly(ε‐caprolactone) hybrid nanocomposites: Thermal–mechanical properties

This paper reports on the thermal behavior and mechanical properties of nanocomposites based on unsaturated polyester resin (UP) modified with poly(ɛ‐caprolactone) (PCL) and reinforced with an organically modified clay (cloisite 30B). To optimize the dispersion of 30B and the mixing of PCL in the UP resin, two different methods were employed to prepare crosslinked UP–PCL‐30B hybrid nanocomposites. Besides, two samples of poly(ɛ‐caprolactone) of different molecular weight (PCL2: M_n = 2.10³g.mol⁻¹ and PCL50: M_n = 5.10⁴g.mol⁻¹) were used at several concentrations (4, 6, 10 wt%). The 30B concentration was 4 wt% in all the nanocomposites. The morphology of the samples was studied by scanning electron microscopy (SEM). The analysis of X‐ray patterns reveals that intercalated structures have been found for all ternary nanocomposites, independently of the molecular weight, PCL concentration and the preparation method selected. A slight rise of the glass transition temperature, T_g, is observed in UP/PCL/4%30B ternary nanocomposites regarding to neat UP. The analysis of the tensile properties of the ternary (hybrid) systems indicates that UP/4%PCL2/4%30B nanocomposite improves the tensile strength and elongation at break respect to the neat UP while the Young modulus remains constant. POLYM. COMPOS., 35:827–838, 2014. © 2013 Society of Plastics Engineers     

AB‐ and ABC‐type di‐ and triblock copolymers of poly[styrene‐block‐(ε‐caprolactone)] and poly[styrene‐block‐(ε‐caprolactone)‐block‐lactide]: synthesis,characterization and thermal studies

Polystyrene terminated with benzyl alcohol units was employed as a macroinitiator for ring‐opening polymerization of ε‐caprolactone and L ‐lactide to yield AB‐ and ABC‐type block copolymers. Even though there are many reports on the diblock copolymers of poly(styrene‐block‐lactide) and poly(styrene‐block‐lactone), this is the first report on the poly(styrene‐block‐lactone‐block‐lactide) triblock copolymer consisting of two semicrystalline and degradable segments. The triblock copolymers exhibited twin melting behavior in differential scanning calorimetry (DSC) analysis with thermal transitions corresponding to each of the lactone and lactide blocks. The block derived from ε‐caprolactone also showed crystallization transitions upon cooling from the melt. In the DSC analysis, one of the triblock copolymers showed an exothermic transition well above the melting temperature upon cooling. Thermogravimetric analysis of these block copolymers showed a two‐step degradation curve for the diblock copolymer and a three‐step degradation for the triblock copolymer with each of the degradation steps associated with each segment of the block copolymers. The present study shows that it is possible to make pure triblock copolymers with two semicrystalline segments which also consist of degradable blocks. Copyright © 2009 Society of Chemical Industry     

Study of the biodegradable poly(ε‐caprolactone)/clay nanocomposite foams

In this article, biodegradable poly(ε‐caprolactone)/layered silicate nanocomposites were prepared and characterized. The dispersion state of modified clay in PCL matrix and its effect on thermal, rheological and mechanical properties of PCL were studied. The PCL/clay nanocomposites were then foamed using chemical foaming method. Cellular parameters such as mean cell size, cell wall thickness and cell densities of nanocomposite foams with different clay loading were collected. Effect of layered silicate on the structure and mechanical properties of PCL foams were evaluated. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Multiarm hyperbranched polyester‐b‐Poly(ε‐caprolactone):Plasticization effect and migration resistance for PVC

A series of multiarm structure hyperbranched polyester‐b‐poly(ε‐caprolactone) (HEPCLs) with different lengths of poly(ε‐caprolactone) (PCL) segments (s = 3, 6, 7, 8) were synthesized. Hyperbranched polyester (HE) was synthesized from glycidol and succinic anhydride and used as a macromolecular polymerization initiator for ε‐caprolactone. The HEPCLs were used as polyvinyl chloride (PVC) plasticizers and the mechanical properties, thermal properties, morphology, and migration stabilities of PVC films were explored. The plasticizing efficiency increased with the increase in PCL segments, and the plasticizing efficiency of HEPCL₈ exceeded that of dioctyl phthalate. Scanning electron microscopy and solid‐state ¹H NMR showed that the HEPCLs possess better compatibility with PVC than HE. Moreover, HEPCLs exhibited excellent migration stability even at very harsh condition, indicating that HEPCLs can be used as no‐migration PVC plasticizers in medical products, children's toys, and food packaging. J. VINYL ADDIT. TECHNOL., 26:35–42, 2020. © 2019 Society of Plastics Engineers