CMOS on-chip electrostatic discharge protection circuit using four-SCR structures with low ESD-trigger voltage

A robust CMOS on-chip ESD protection circuit is proposed, which consists of four parasitic lateral SCR devices with low ESD trigger voltages to protect NMOS and PMOS devices of the internal circuits against the ESD pulses with both positive and negative polarities with respect to either VDD or VSS(GND) nodes. For each ESD stress with positive or negative polarity, there is an efficient and direct shunt path generated by the SCR low-impedance latching state to quickly bypass the ESD current. Thus, this four-SCR ESD protection circuit can perform very efficient protection in a small layout area. Since there is no diffusion or polysilicon resistor in the proposed ESD protection circuit, the RC delay between each I/O pad and its internal circuits is very low and high-speed applications are feasible. The experimental results show that this four-SCR protection circuit can successfully perform very effective protection against ESD damage. Moreover, the proposed ESD protection circuit is fully process-compatible with n-well or p-well CMOS and BiCMOS technologies.     

Electrostatic discharge protection scheme without leakage current path for CMOS IC operating in power-down-mode condition on a system board

A new design on the electrostatic discharge (ESD) protection scheme for CMOS IC operating in power-down-mode condition is proposed. By adding a VDD_ESD bus line and diodes, the new proposed ESD protection scheme can block the leakage current from I/O pin to VDD power line to avoid malfunction during power-down-mode operating condition. During normal circuit operating condition, the new proposed ESD protection schemes have no leakage path to interfere with the normal circuit functions. The whole-chip ESD protection design can be achieved by insertion of ESD clamp circuits between VSS power line and both VDD power line and VDD ESD bus line. Experimental results have verified that the human-body-model (HBM) ESD level of this new scheme can be greater than 7.5 kV in a 0.35-μm silicided CMOS process. Furthermore, output-swing improvement circuit is proposed to achieve the full swing of output voltage level during normal circuit operating condition.     

Electrostatic discharge protection design for mixed-voltage CMOS I/O buffers

A new electrostatic discharge (ESD) protection circuit, using the stacked-nMOS triggered silicon controlled rectifier (SNTSCR) as the ESD clamp device, is designed to protect the mixed-voltage I/O buffers of CMOS ICs. The new proposed ESD protection circuit, which combines the stacked-nMOS structure with the gate-coupling circuit technique into the SCR device, is fully compatible to general CMOS processes without causing the gate-oxide reliability problem. Without using the thick gate oxide, the experimental results in a 0.35 /spl mu/m CMOS process have proven that the human-body-model ESD level of the mixed-voltage I/O buffer can be successfully increased from the original /spl sim/2 kV to >8 kV by using this proposed ESD protection circuit.     

On-chip ESD protection design with substrate-triggered technique for mixed-Voltage I/O circuits in subquarter-micrometer CMOS Process

A new electrostatic discharge (ESD) protection design, by using the substrate-triggered stacked-nMOS device, is proposed to protect the mixed-voltage I/O circuits of CMOS ICs. The substrate-triggered technique is applied to lower the trigger voltage of the stacked-nMOS device to ensure effective ESD protection for the mixed-voltage I/O circuits. The proposed ESD protection circuit with the substrate-triggered technique is fully compatible to general CMOS process without causing the gate-oxide reliability problem. Without using the thick gate oxide, the new proposed design has been fabricated and verified for 2.5/3.3-V tolerant mixed-voltage I/O circuit in a 0.25-/spl mu/m salicided CMOS process. The experimental results have confirmed that the human-body-model ESD level of the mixed-voltage I/O buffers can be successfully improved from the original 3.4 to 5.6 kV by using this new proposed ESD protection circuit.     

A gate-coupled PTLSCR/NTLSCR ESD protection circuit fordeep-submicron low-voltage CMOS ICs

A novel electrostatic discharge (ESD) protection circuit, which combines complementary low-voltage-triggered lateral SCR (LVTSCR) devices and the gate-coupling technique, is proposed to effectively protect the thinner gate oxide of deep submicron CMOS ICs without adding an extra ESD-implant mask. Gate-coupling technique is used to couple the ESD-transient voltage to the gates of the PMOS-triggered/NMOS-triggered lateral silicon controlled rectifier (SCR) (PTLSCR/NTLSCR) devices to turn on the lateral SCR devices during an ESD stress. The trigger voltage of gate-coupled lateral SCR devices can be significantly reduced by the coupling capacitor. Thus, the thinner gate oxide of the input buffers in deep-submicron low-voltage CMOS ICs can be fully protected against ESD damage. Experimental results have verified that this proposed ESD protection circuit with a trigger voltage about 7 V can provide 4.8 (3.3) times human-body-model (HBM) [machine-model (MM)] ESD failure levels while occupying 47% of layout area, as compared with a conventional CMOS ESD protection circuit     

Complementary-SCR ESD protection circuit with interdigitatedfinger-type layout for input pads of submicron CMOS IC's

A new ESD protection circuit with complementary SCR structures and junction diodes is proposed. This complementary-SCR ESD protection circuit with interdigitated finger-type layout has been successfully fabricated and verified in a 0.6 μm CMOS SRAM technology with the LDD process. The proposed ESD protection circuit can be free of VDD-to-VSS latchup under 5 V VDD operation by means of a base-emitter shorting method. To compensate for the degradation on latching capability of lateral SCR devices in the ESD protection circuit caused by the base-emitter shorting method, the p-well to p-well spacing of lateral BJT's in the lateral SCR devices is reduced to lower its ESD-trigger voltage and to enhance turn-on speed of positive-feedback regeneration in the lateral SCR devices. This ESD protection circuit can perform at high ESD failure threshold in small layout areas, so it is very suitable for submicron CMOS VLSI/ULSI's in high-pin-count or high-density applications     

Transmission gate switch for ESD protection of RF pad

A novel transmission gate switch is proposed to effectively replace electrostatic discharge (ESD) protection resistors in CMOS I/O pads. The proposed circuit exhibits a very low on resistance, under normal operation, and a very high off resistance, in the case of ESD stresses. A triple-well CMOS implementation guarantees RF operation and enhanced ESD reliability     

ESD protection design for mixed-voltage I/O buffer with substrate-triggered circuit

A substrate-triggered technique is proposed to improve the electrostatic discharge (ESD) robustness of a stacked-nMOS device in the mixed-voltage I/O circuit. The substrate-triggered technique can further lower the trigger voltage of a stacked-nMOS device to ensure effective ESD protection for mixed-voltage I/O circuits. The proposed ESD protection circuit with substrate-triggered design for a 2.5-V/3.3-V-tolerant mixed-voltage I/O circuit has been fabricated and verified in a 0.25-/spl mu/m salicided CMOS process. The substrate-triggered circuit for a mixed-voltage I/O buffer to meet the desired circuit application in different CMOS processes can be easily adjusted by using HSPICE simulation. Experimental results have confirmed that the human- body-model (HBM) ESD robustness of a mixed-voltage I/O circuit can be increased /spl sim/60% by this substrate-triggered design.     

Substrate-triggered ESD protection circuit without extra process modification

A substrate-triggered technique is proposed to improve electrostatic discharge (ESD) protection efficiency of ESD protection circuits without extra salicide blocking and ESD-implantation process modifications in a salicided shallow-trench-isolation CMOS process. By using the layout technique, the whole ESD protection circuit can be merged into a compact device structure to enhance the substrate-triggered efficiency. This substrate-triggered design can increase ESD robustness and reduce the trigger voltage of the ESD protection device. This substrate-triggered ESD protection circuit with a field oxide device of channel width of 150 /spl mu/m can sustain a human-body-model ESD level of 3250 V without any extra process modification. Comparing to the traditional ESD protection design of gate-grounded nMOS (ggnMOS) with silicide-blocking process modification in a 0.25-/spl mu/m salicided CMOS process, the proposed substrate-triggered design without extra process modification can improve ESD robustness per unit silicon area from the original 1.2 V//spl mu/m/sup 2/ of ggnMOS to 1.73 V//spl mu/m/sup 2/.     

CMOS集成电路中电源和地之间的ESD保护电路设计

讨论了3种常用的CMOS集成电路电源和地之间的ESD保护电路,分别介绍了它们的电路结构以及设计考虑,并用Hspice对其中利用晶体管延时的电源和地的保护电路在ESD脉冲和正常工作两种情况下的工作进行了模拟验证。结论证明：在ESD脉冲下,该保护电路的导通时间为380ns;在正常工作时。该保护电路不会导通．因此这种利用晶体管延时的保护电路完全可以作为CMOS集成电路电源和地之间的ESD保护电路。     

Capacitor-couple ESD protection circuit for deep-submicronlow-voltage CMOS ASIC

Capacitor-couple technique used to lower snapback-trigger voltage and to ensure uniform ESD current distribution in deep-submicron CMOS on-chip ESD protection circuit is proposed. The coupling capacitor is realized by a poly layer right under the wire-bonding metal pad without increasing extra layout area to the pad. A timing-original design model has been derived to calculate the capacitor-couple efficiency of this proposed ESD protection circuit. Using this capacitor-couple ESD protection circuit, the thinner gate oxide of CMOS devices in deep-submicron low-voltage CMOS ASIC can be effectively protected     

ESD Protection Design With On-Chip ESD Bus and High-Voltage-Tolerant ESD Clamp Circuit for Mixed-Voltage I/O Buffers

Considering gate-oxide reliability, a new electrostatic discharge (ESD) protection scheme with an on-chip ESD bus (ESD_BUS) and a high-voltage-tolerant ESD clamp circuit for 1.2/2.5 V mixed-voltage I/O interfaces is proposed. The devices used in the high-voltage-tolerant ESD clamp circuit are all 1.2 V low-voltage N- and P-type MOS devices that can be safely operated under the 2.5-V bias conditions without suffering from the gate-oxide reliability issue. The four-mode (positive-to-V_SS, negative-to-V_SS, positive-to-V_DD, and negative-to-V_DD) ESD stresses on the mixed-voltage I/O pad and pin-to-pin ESD stresses can be effectively discharged by the proposed ESD protection scheme. The experimental results verified in a 0.13-mum CMOS process have confirmed that the proposed new ESD protection scheme has high human-body model (HBM) and machine-model (MM) ESD robustness with a fast turn-on speed. The proposed new ESD protection scheme, which is designed with only low- voltage devices, is an excellent and cost-efficient solution to protect mixed-voltage I/O interfaces.     

ESD protection design on analog pin with very low input capacitancefor high-frequency or current-mode applications

An electrostatic discharge (ESD) protection design is proposed to solve the ESD protection challenge to the analog pins: for high-frequency or current-mode applications, By including an efficient power-rails clamp circuit in the analog input/output (I/O) pin, the device dimension (W/L) of an ESD clamp device connected to the I/O pad in the analog ESD protection circuit can be reduced to only 50/0.5 (μm/μm) in a 0.35-μm silicided CMOS process, but it can sustain the human body model (HBM) and machine model (MM) ESD level of up to 6 kV (400 V). With such a smaller device dimension, the input capacitance of this analog ESD protection circuit can be significantly reduced to only ~1.0 pF (including the bond-pad capacitance) for high-frequency applications     

Characteristics analysis and optimization design of a new ESD power clamp circuit

As CMOS technology scales down, the design of ESD protection circuits becomes more challenging. There are some disadvantages for the actual power clamp circuit. In this paper, an optimization ESD power clamp circuit is proposed. The new clamp circuit adopts the edge triggering True Single Phase Clocked Logic (TSPCL) D flip-flop to turn on and time delay, it has the advantage of dynamic transmission structure. By adding a leakage transistor of small size, the clamp circuit can turn off effectively. By changing the W/L ratio, the clamp can safely protect the gate of ESD power clamp devices from thermoelectric breakdown. The results show that the circuit can reduce the false triggering and power supply noise more effectively, it can be widely used in high-speed integrated circuits. The proposed structure has the advantages of low power and low cost, and can be used to the system-level ESD protection.     

由版图引起的CMOS ESD保护电路失效的分析

ESD保护电路已经成为CMOS集成电路不可或缺的组成部分,在当前CMOS IC特征尺寸进入深亚微米时代后,如何避免由ESD应力导致的保护电路的击穿已经成为CMOS IC设计过程中一个棘手的问题.光发射显微镜利用了IC芯片失效点所产生的显微红外发光现象可以对失效部位进行定位,结合版图分析以及微分析技术,如扫描电子显微镜SEM、聚焦离子束FIB等的应用可以揭示ESD保护电路的失效原因及其机理.通过对两个击穿失效的CMOS功率ICESD保护电路实际案例的分析和研究,提出了改进ESD保护电路版图设计的途径.     

On-Chip Transient Detection Circuit for System-Level ESD Protection in CMOS Integrated Circuits to Meet Electromagnetic Compatibility Regulation

A new on-chip transient detection circuit for system-level electrostatic discharge (ESD) protection is proposed. The circuit performance to detect different positive and negative fast electrical transients has been investigated by the HSPICE simulator and verified in a silicon chip. The experimental results in a 0.13-m CMOS integrated circuit (IC) have confirmed that the proposed on-chip transient detection circuit can be used to detect fast electrical transients during the system-level ESD events. The proposed transient detection circuit can be further combined with the power-on reset circuit to improve the immunity of the CMOS IC products against system-level ESD stress.     

Ladder-shaped network for ESD protection of millimetre-wave CMOS ICs

A compact ladder-shaped electrostatic discharge (ESD) protection circuit is presented for millimetre-wave integrated circuits (ICs) in CMOS technology. Multiple shorted shunt stubs form a ladder network together with series stubs as ESD protection that discharges current/voltage pulses caused by an ESD event, while at the same time the network is embedded as part of the matching circuit for a normal operation. A 60 GHz low-noise amplifier using a 90 nm CMOS process is demonstrated with the proposed ESD protection methodology that introduces less than 1 dB insertion loss. Owing to the ESD current distribution through multiple shorted stubs, the proposed methodology is useful to millimetre-wave ICs with advanced CMOS technology that suffers from higher sheet resistance of the metal layers.     

Highly Robust AHHVSCR‐Based ESD Protection Circuit

In this paper, a new structure for an advanced high holding voltage silicon controlled rectifier (AHHVSCR) is proposed. The proposed new structure specifically for an AHHVSCR‐based electrostatic discharge (ESD) protection circuit can protect integrated circuits from ESD stress. The new structure involves the insertion of a PMOS into an AHHVSCR so as to prevent a state of latch‐up from occurring due to a low holding voltage. We use a TACD simulation to conduct a comparative analysis of three types of circuit — (i) an AHHVSCR‐based ESD protection circuit having the proposed new structure (that is, a PMOS inserted into the AHHVSCR), (ii) a standard AHHVSCR‐based ESD protection circuit, and (iii) a standard HHVSCR‐based ESD protection circuit. A circuit having the proposed new structure is fabricated using 0.18 μm Bipolar‐CMOS–DMOS technology. The fabricated circuit is also evaluated using Transmission‐Line Pulse measurements to confirm its electrical characteristics, and human‐body model and machine model tests are used to confirm its robustness. The fabricated circuit has a holding voltage of 18.78 V and a second breakdown current of more than 8 A.     

Investigation and Design of On-Chip Power-Rail ESD Clamp Circuits Without Suffering Latchup-Like Failure During System-Level ESD Test

On-chip power-rail electrostatic discharge (ESD) protection circuit designed with active ESD detection function is the key role to significantly improve ESD robustness of CMOS integrated circuits (ICs). Four power-rail ESD clamp circuits with different ESD-transient detection circuits were fabricated in a 0.18-$mu{hbox{m}}$ CMOS process and tested to compare their system-level ESD susceptibility, which are named as power-rail ESD clamp circuits with typical RC-based detection, PMOS feedback, NMOS+PMOS feedback, and cascaded PMOS feedback in this work. During the system-level ESD test, where the ICs in a system have been powered up, the feedback loop used in the power-rail ESD clamp circuits provides the lock function to keep the ESD-clamping NMOS in a “latch-on” state. The latch-on ESD-clamping NMOS, which is often drawn with a larger device dimension to sustain high ESD level, conducts a huge current between the power lines to perform a latchup-like failure after the system-level ESD test. A modified power-rail ESD clamp circuit is proposed to solve this problem. The proposed power-rail ESD clamp circuit can provide high enough chip-level ESD robustness, and without suffering the latchup-like failure during the system-level ESD test.      

Electrostatic discharge (ESD) protection for CMOS output buffers in scaled-down VLSI technology

To provide area-efficient output ESD protection for the scaled-down CMOS VLSI, a new output ESD protection is proposed. In the new output ESD protection circuit, there are two novel devices, the PTLSCR (PMOS-trigger lateral SCR) and the NTLSCR (NMOS-trigger lateral SCR). The PTLSCR is in parallel and merged with the output PMOS, and the NTLSCR is in parallel and merged with the output NMOS, to provide area-efficient ESD protection for CMOS output buffers. The trigger voltages of PTLSCR and NTLSCR are lowered below the breakdown voltages of the output PMOS and NMOS in the CMOS output buffer. The PTLSCR and NTLSCR are guaranteed to be turned on first before the output PMOS or NMOS are broken down by the ESD voltage. Experimental results have shown that the PTLSCR and NTLSCR can sustain over 4000 V (700 V) of the human-body-model (machine-model) ESD stresses within a very small layout area in a 0.6 μm CMOS technology with LDD and polycide processes. The noise margin of the proposed output ESD protection design is greater than 8 V (lower than −3.3 V) to avoid the undesired triggering on the NTLSCR (PTLSCR) due to the overshooting (undershooting) voltage pulse on the output pad when the IC is under normal operating conditions with 5 V VDD and 0 V VSS power supplies.