Bi_2O_3对堇青石陶瓷的烧结行为、相变和热膨胀性能的影响

采用X射线衍射仪、差热分析仪和热膨胀仪等手段研究了由氧化物粉末 (MgO、Al2 O3 和SiO2 )制备堇青石陶瓷时 ,添加Bi2 O3 对堇青石陶瓷相变和性能的影响 ,分析了Bi2 O3 在烧结过程中的作用机理是低温产生液相促进烧结。试验表明 ,Bi2 O3 能明显降低烧结温度 ,在 12 5 0℃烧成 3h后的陶瓷是由α堇青石和少量的 μ堇青石组成。随着Bi2 O3 含量增加 ,陶瓷的致密度和热膨胀系数逐渐升高。Bi2 O3 的添加量 (质量分数 )为 0 .0 4 ,原料相石英消失。Bi-O膨胀系数较Si-O的大和Bi3 + 离子进入堇青石晶格中是引起堇青石陶瓷热膨胀系数升高的主要原因。     

Bi2O3对堇青石陶瓷的相组成、微观结构和性能的影响

采用X射线衍射、扫描电镜、差热分析和热膨胀仪等手段研究了由氧化物粉末(MgO，Ai2O3和SiO2)制备堇青石陶瓷时，添加Bi2O3对堇青石陶瓷相变、相组成和性能的影响，Bi2O3在烧结过程中的作用机理是低温产生液相促进烧结。试验表明，在1350℃烧结3h，该陶瓷由堇青石和孤立分布的玻璃相组成。随Bi2O3含量增加，陶瓷的致密度、弯曲强度和热膨胀系数逐渐升高。Bi2O3的添加量(质量分数)大于4％时，原料相石英消失。硅氧网络骨架结合力减小和一定量的玻璃相是引起堇青石陶瓷热膨胀系数升高的主要原因。     

镍渣制备多孔堇青石陶瓷的研究

以镍渣、Al_2O_3和SiO_2为原料,按偏镁铝方案确定堇青石的组成,无需添加额外的烧结助剂和造孔剂,成功制备出多孔堇青石陶瓷。测定了试样的显气孔率、抗弯强度和热膨胀系数,用XRD分析了试样在烧结过程中的物相变化,并用SEM观察其断面的显微结构。结果表明:在1200~1380℃保温4 h,制备的多孔陶瓷的显气孔率为38.13~31.39%,抗弯强度为25.53~32.54 MPa,热膨胀系数为3.17×10~(-6)~1.43×10~(-6)/℃,且其主晶相为堇青石。SEM图谱显示多孔堇青石陶瓷中堇青石晶体呈六方棱柱状,还存在大量孔洞。     

蜂窝陶瓷用堇青石的研制

1前言峰窝陶瓷作为汽车尾气净化器的催化剂载体具有热膨胀系数小、抗热震性高、热容小、比表面积大等特性，它能消除尾气中的有害气体，防止污染。目前，全球性的汽车尾气治理方兴未艾，我国也把治理汽车尾气工作摆在重要位置。鉴此，我们厂于1996年和上海某公司共同承担了研制开发汽车尾气净化器的环保项目。我厂重点研制蜂窝陶瓷用材料--合成堇青石，经过近一年的试验，合成堇青石完全达到了要求指标，现已批量生产。本文就堇青石的特性及研制情况作一介绍。2堇青石的特性董青石（2Mgo·2Al2O3·5SiO2）主要由高岭土（Al2O3·2SiO2·2…     

SiO2/Al2O3摩尔比对堇青石微晶釉结构与性能的影响

以矿物为主要原料采用生料釉法制备堇青石微晶釉,探究了不同SiO2/Al2O3摩尔比对堇青石微晶釉结构和性能的影响。通过高温显微镜、XRD、FT-IR、SEM等对堇青石微晶釉进行了测试表征,并测试其热膨胀系数、釉面硬度和白度。结果表明:随着SiO2/Al2O3摩尔比从7.7降低到3.5,釉的流动性先提高后降低,釉中存在的主晶相由单一顽火辉石转变为顽火辉石和α-堇青石共存再到单一α-堇青石最后转变为α-堇青石和镁铝尖晶石。且釉中α-堇青石含量先增加后减少,热膨胀系数先降低后升高,釉面硬度先增大后减小,白度先减小后增大;当SiO2/Al2O3摩尔比为4.0时,样品的综合性能最佳,α-堇青石含量最高,为19.8%,釉的热膨胀系数为4.37×10-6(600℃),釉面硬度为6.9 GPa,白度为69.1 Wb。     

低热膨胀系数堇青石材料的合成研究

以高岭土、烧滑石和氧化镁为原料合成堇青石,研究了烧成温度、镁铝硅含量及高岭土种类对合成堇青石热膨胀系数的影响。实验结果表明:合成堇青石的最佳配方1#高岭土82.4 wt%、滑石9.3 wt%、氧化镁8.4 wt%,试样热膨胀系数为1.24×10-6℃-1。适当的提高烧成温度可得到热膨胀系数低的堇青石材料,但合成温度过高则会因为形成过多的玻璃相而使其热膨胀系数增大。过多或过少的引入Si O2、Al2O3、Mg O均会由于形成高热膨胀系数的晶相而导致所合成堇青石的热膨胀系数增大。     

蜂窝陶瓷蓄热材料的研究现状

蜂窝陶瓷蓄热材料应该具有热膨胀系数低、比热容大、比表面积大、导热性能好、抗热震性好等特性。本文详细介绍了几种多孔陶瓷材料的优缺点,指出堇青石质复相材料是目前研究最广泛的蜂窝陶瓷材料。堇青石与多种催化剂匹配性好,比表面积大、热膨胀系数小,但耐热性稍差,于是通过添加一些添加剂来提高堇青石作为蜂窝陶瓷蓄热体的性能。这些添加剂与堇青石结合形成复相材料,可以降低热膨胀系数、提高抗热震性等。     

煤矸石在堇青石蜂窝陶瓷催化剂载体中的应用与研究

董青石蜂窝陶瓷具有极低的热膨胀系数、较好的抗热震性、较高的化学稳定性,是优良的汽车净化器催化剂载体材料。煤矸石主要成分为SiO₂和Al₂O₃,在陶瓷行业的利用一直是本领域研究的热点。以山西煤矸石为主要研究对象,通过对采用不同化学组成、粒度分布和微观形貌的煤矸石制备的堇青石蜂窝陶瓷载体样品热膨胀系数进行测定,考察了煤矸石对堇青石蜂窝陶瓷性能的影响。结果表明：不同化学组成的煤矸石制得的蜂窝陶瓷越接近堇青石的理论组成51.4wt.%SiO₂、34.9wt.%Al₂O₃、13.7wt.%MgO,热膨胀系数就越低。随着煤矸石颗粒越细,堇青石蜂窝陶瓷的热膨胀系数越低,选用250目煤矸石原料粉末时,热膨胀系数为1.662×10^-6℃^-1。采用微观形貌为片状的煤矸石粉末比用球形的煤矸石粉末制得的堇青石蜂窝陶瓷热膨胀系数更低。     

堇青石陶瓷烧结工艺及机理研究

本文利用DSC、XRD技术，研究了MgO、Al2O3，和SiO2反应烧结制备堇青石陶瓷的机理。结果表明MgO和Al2O3在1155℃反应合成镁铝尖晶石(MgAl2O4)，进而在1317℃长时间保温与SiO2反应生成堇青石。     

SiO_2—Al_2O_3—MgO—K_2O—MgF_2系玻璃陶瓷析晶机理及断裂机制

以SiO2—Al2O3—MgO—K2O—MgF2体系玻璃为基础,采用整体析晶法,在高温条件下制备出堇青石/氟金云母玻璃陶瓷。借助于综合热分析仪、X射线衍射仪和扫描电子显微镜等分析手段,研究了玻璃陶瓷的析晶机制、显微形貌和断裂机制。结果表明:所制备的玻璃陶瓷主晶相为板条状氟金云母和β-堇青石,经1 000℃保温3h热处理后,主晶相转变为镁橄榄石;以堇青石和氟金云母为主晶相的玻璃陶瓷断裂机理为穿晶断裂,以镁橄榄石为主晶相的玻璃陶瓷为沿晶断裂。在基础玻璃中添加5%B2O3,可抑制氟金云母相的析出,并提高玻璃陶瓷的致密度。     

氢气纯度分析方法准确性的探讨

ONACCURACYOFANALYSISOFOFHYDROGEN1前言我公司目前应用的氢气纯度分析方法有两种,一种是爆炸反应法,另一种是焦性没食子酸吸收法。几年来,人们对两种分析方法的准确性曾有过褒贬不一的评论。这里我们也谈谈自己粗浅的观点。2爆炸法测定氢气纯度一定量的氢气样品与适量的空气之均匀混合物因反应后生成液体水而引起气体体积减少,减少的体积等于参加反应气体体积之和。其中l／3为氧气,2／3为氢气。根据氢气取样量和反应前后混气体体积之差,以及氢气在反应中的体积比例关系,可计算出样品的氢气纯度。计算公式式中：A一混…     

COMPARISON OF METHODS OF ANALYSIS OF GYPSUM1

The different analytical methods proposed for the evaluation of gypsum have been subjected to an experimental test. A combination method, consisting of a fusion with KHCO₃ and determination of CaO by KMnO₄ titration, the SO₃ by Andrews method of titration of BaCrO₄ has been found to give very reliable results with the least consumption of time.     

SEDIMENTATION OF BINARY MIXTURES OF PARTICLES OF UNEQUAL DENSITIES AND OF DIFFERENT SIZES

A model is developed for the sedimentation from a suspension of two particle species of unequal densities and of different sizes. The composition and the thickness of various layers in the sediments are predicted using graphical and analytical methods. The model predictions were in excellent agreement with experimental results, when the particle size ratio was ≥ 108. When size ratio of the particles was 2.60 and 4.31 the agreement occurred in about 50 percent of the cases.     

HEASUREHENT OF INSTANTANEOUS RATES OF LOSS OF VOIATILE COMPOUNDS DURING DRYING OF DROPS

A novel technique serves to monitor instantaneous rates of loss of a volatile solute from a suspended drop during drying. A highly sensitive electron capture detector is used to monitor concentrations of SF6 released into a flowing gas stream from a suspended, drying drop. Simultaneously, the appearance and morphological development of the drop are monitored with a video camera. This provides the wherewithal of relating instantaneous rates of loss of the volatile solute to particular events during the development of particle morphology.

Initial experiments have been carried out with drops of aqueous solutions of glucose, sucrose, maltodextrin and coffee extract. The results clearly display the onset of the volatiles-retentive selective diffusion phenomenon. There is also substantial loss of the volatile component later in the drying process, when the drops undergo repeated ex ansion, bursting and cratering due to the formation of internaf bubbles. These experiments appear to be the first quantitative demonstration of major losses accompanying changes in drop morphology.     

几种针状焦性能对比

针状焦分石油系和煤系两大类,这主要取决于针状焦的原料来源。在同一系列中由于原料不同和工艺条件不同 ,针状焦的各自性能也不相同。针状焦是生产超高功率石墨电极和高功率石墨电极的主要原料 ,针状焦的性能对石墨电极的质量有至关重要的影响。所以对针状焦性能以及其对石墨电极质量影响的研究十分必要的。以下是常用的几种进口针状焦和国产针状焦的性能对比。１原料性能分析对比原料试样包括４种针状焦 ,其中两种为进口针状焦：三菱针状焦和新日化针状焦;另两种为国产针状焦：鞍山针状焦和锦州针状焦。其中除锦州针状焦是石油系针状焦外…     

茶多酚提取方法进展

本文综述了国内外现有茶多酚提取方法的现状以及近期的研究进展，并对其优缺点进行了评价。这将有助于中低档茶的综合利用和茶多酚的进一步开发应用。     

ANALYSIS OF RECENT MEASUREMENTS OF THE VISCOSITY OF GLASSES

Viscosity of Simple Soda-Silicate 500° to 1400°C Comparison of the results given by English with those of Washburn, Shelton and Libman, indicates a discrepancy in the absolute values of log₁₀ viscosity amounting to 0.6, those of Washburn et al., being relatively too high. If correction for this is made, the isothermal curves of log₁₀ viscosity as a function of soda content are smooth up to 50% Na₂O, showing no inflection. The observations as a function of temperature T are all represented within accidental error by an equation of the type where all three constants vary regularly with the composition. Change of Viscosity of Glass (6SiO₂, 2Na₂O) due to Molecular Substitution of CaO, MgO and Al₂O₃ for Na₂O The effect is clearly brought out by plotting (from the results of English) the change of log₁₀η due to the substitution as a function of temperature. The curves each show a sharp bend at a temperature between 840° and 1050°C, which is designated the aggregation temperature T_a. If we divide these curves by the corresponding percentage substituted, we get curves for each oxide which are straight and parallel below the aggregation temperatures, the slopes (increase of change of log₁₀η per 100°C) being −0.056 (CaO), −0.055 (MgO), −0.018 (A1₂O₃) per per cent oxide substituted. For substitution of 1/2 molecule the slopes are −0.325 (CaO), −0.23 (MgO) and −0.18 (Al₂O₃) per 100°. At the aggregation temperature the change of log₁₀η per per cent is a minimum, 0.03 to 0.06 for CaO, 0.12 for MgO, 0.07 for Al₂O₃. Evidence of Aggregation in Glasses, from viscosity Measurements The sharp bends in the plots of change of log₁₀η due to substitution of an oxide for Na₂O, suggest the beginning of molecular aggregation at these temperatures. These aggregation temperatures are close to the devitrification temperatures, but the effect on the viscosity curves cannot be due to actual devitrification since it does not change with time. Taking the aggregation temperatures as equal to devitrification temperatures, additional isotherms are roughly sketched into the equilibrium triangle of the system Na₂O-CaO-SiO₂. Change of Viscosity of Glass (4SiO₂, 2Na₂O) due to of Substitution of B₂O₃ for SiO₂ The change of log₁₀η (from the results of English) is plotted as a function of temperature, and also the change of log₁₀η per per cent B₂O₃. The curves are more complex than for the substitution for Na₂O.     

环氧树脂羟基值测定方法的研究

利用乙酸酐、吡啶和浓硫酸混合的乙酰化试剂测定环氧树脂中羟基值含量的方法具有操作简便、滴定终点明显和分析结果误差小等优点。     

骑式摩托车油箱喷涂工艺的改进

面对日益激烈的市场竞争,摩托车油箱外观质量越来越成为影响销售的因素之一。文章介绍了改进工艺后的油箱涂装,该涂装体系提高了油箱外观的丰满度,降低了油箱涂装的生产成本。     

聚酰亚胺的合成法

本文评述了缩聚型聚酰亚胺的主要合成方法和近年来国际上在合成中所做的探索。