Morphology study of oriented SmBCO film deposited by MOCVD

c-axis-oriented SmBa_2Cu_3O_7(SmBCO) films have been deposited on(100)- LaA1O_3(LAO)substrate by metal organic chemical vapor deposition(MOCVD) technique.The effects of deposition temperature(T_(dep)) and total pressure(P_(tot)) on the orientation and microstructure of SmBCO films were investigated.The orientation of SmBCO films transformed from α-axis to c-axis with increasing of T_(dep) from 900 to 1 100℃.At T_(dep)=1 050℃,SmBCO films had c-axis orientation and tetragon surface.At P_(tot)~(dep)=400-800 Pa and T_(dep)=1 050 ℃,totally c-axis-oriented SmBCO films were obtained.The R_(dep) of SmBCO films increased firstly and then decreased with increasing P_(tot).The surface of SmBCO films exhibited tetragon morphology at 1 050 ℃ and400 Pa.Maximum thickness of SmBCO film deposited was 1.2μm at P_(tot)= 600 Pa,and the corresponding R_(dep)was 7.2 μm·h~(-1).     

Effects of annealing processes on Cu<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Si<Subscript>1-<Emphasis Type="Italic">x</Emphasis></Subscript> thin films

The Cu _x Si_1-x thin films have been grown by pulsed laser deposition (PLD) with in situ annealing on Si (001) and Si (111), respectively. The transformation of phase was detected by X-ray diffraction (XRD). The results showed that the as-deposited films were composed of Cu on both Si (001) and Si (111). The annealed thin films consisted of Cu + η”-Cu₃Si on Si (001) while Cu + η’-Cu₃Si on Si (111), respectively, at annealed temperature (T _a) = 300-600 °C. With the further increasing of T _a, at T _a= 700 °C, there was only one main phase, η”-Cu₃Si on Si (001) while η’-Cu₃Si on Si (111), respectively. The annealed thin films transformed from continuous dense structure to scattered-grain morphology with increasing T _a detected by field emission scanning electron microscope (FESEM). It was also showed that the grain size would enlarge with increasing annealing time (t _a).     

Synthesis of MnxZn（1-x）Fe2O4 Nanopartieles by Ball-milling Hydrothermal Method

SMnxZn1-xFe2O4 （x=1,0.9,0.8,0.7,0.6,0.5,0.25,0） nanoparticles were prepared by ball-milling hydrothermal and investigated by X-ray diffraction, DTG and TEM. Nanocrystallite grain size was determined by X-ray linewidth to be from 63 A to 274 A. The thermal properties indicate absorbed water still remain at low temperature, crystalline wate will be decomposed from 230 ℃ to 260 ℃, partial Mn^2＋ will be oxidized near 730 ℃. TEM shows the ferrite particles pocess a spherical morphology and uniform nanosize.     

Effect of Cu-Ti-C reaction composition on reinforcing particles size of TiC<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>/Cu composites

TiC _x /Cu composites were fabricated by combustion synthesis and hot press technology. Using XRD, SEM, EDS, FESEM analysis methods, the effects of various carbon sources and different Cu contents on the microstructures of TiC _x /Cu composites and the size of TiC _x particles were investigated. Results showed that TiC _x reinforcing particles size increases with decreasing Cu content in Cu-Ti-C reaction system. With carbon nanotubes (carbon black) serving as carbon source, the generated TiC _x particles size transits from nanometer to submicron when Cu content corresponding to the reaction system is reduced to 60 vol% (70 vol%); while graphite serves as carbon source, there is no clear limiting concentration. C particles with smaller size, larger specific surface area and better distribution result in finer TiC _x particles, which is more beneficial to generating nano-sized TiC _x /Cu composites.     

Preparation and piezoelectric properties of CuO-added (Ag<Subscript>0.75</Subscript>Li<Subscript>0.1</Subscript>Na<Subscript>0.1</Subscript>K<Subscript>0.05</Subscript>)NbO<Subscript>3</Subscript> lead-free ceramics

CuO-doped (Ag_0.75Li_0.1Na_0.1K_0.05)NbO₃ (ALNKN-xCuO, x = 0–2mol%) lead-free piezoelectric ceramics were prepared by the solid-state reaction method in air atmosphere. The effects of CuO addition on the phase structure, microstructure, and piezoelectric properties of the ceramics were investigated. The experimental results show that the ALNKN ceramics without doping CuO possess rhombohedral phase along with K2Nb6O16-type phase and metallic silver phase. For all of the CuO-doped ALNKN ceramics, a pure perovskite structure with the orthorhombic phase was obtained by enclosing the samples in a corundum tube. A homogeneous microstructure with the grain size of about 1 μm was formed for the ceramics with 0.5mol% CuO. The grain size increases with increasing amount of CuO. The temperature dependence of dielectric properties indicates that the ferroelectric phase of the ALNKN-xCuO ceramics becomes less stable with the addition of CuO. The ceramics with x = 1mol% exhibit relatively good electrical properties along with a high Curie temperature. These results will provide a helpful guidance to preparing other AN-based ceramics by solid-state reaction method in air atmosphere.     

Spontaneous Magnetic Transitions and Corresponding Magnetoelastic Properties of Intermetallic Compounds <Emphasis Type="Italic">R</Emphasis>Mn<Subscript>2</Subscript>Ge<Subscript>2</Subscript> (<Emphasis Type="Italic">R</Emphasis>=Gd,Tb and Dy)

The spontaneous magnetic transitions and corresponding magnetoelastic properties of intermetallic compounds RMn₂Ge₂ (R=Gd, Tb and Dy) were investigated by using the X-ray diffraction method and magnetic measurement. The results showed that the compounds experience two magnetic transitions, namely the second-order paramagnetic to antiferromagnetic transition at temperature T_N (T_N=368, 423 and 443 K for GdMn₂Ge₂, TbMn₂Ge₂ and DyMn₂Ge₂, respectively) and the first-order antiferromagnetic - ferrimagnetic transition at temperature T_t (T_t=96, 80 and 40 K for GdMn₂Ge₂, TbMn₂Ge₂ and DyMn₂Ge₂, respectively) as the temperature decreases. The temperature dependence of the lattice constant a(T) displays a negative magnetoelastic anomaly at the second-order transition point T_N and, at the first-order transition T_t, a increases abruptly for GdMn₂Ge₂ and TbMn₂Ge₂, Δa/a about 10^-3. Nevertheless, the lattice constant c almost does not change at these transition points indicating that such magnetoelastic anomalies are mainly contributed by the Mn-sublattice. The transitions of the magnetoelastic properties are also evidenced on the temperature dependence of magnetic susceptibility χ. The first-order transition behavior at T_t is explained by the Kittel mode of exchange inversion.     

Stability of <Emphasis Type="Italic">γ</Emphasis>′ multimodal microstructure in a Ni-based powder metallurgy superalloy

Multimodal size distribution of γ′ phase was obtained in a slow-cooling experiment following supersolvus solution treatment (1191°C). The morphology of the secondary γ′ particles exhibited splitting and protrusion instabilities. In the subsequent aging process (815°C), reverse coarsening was observed, i.e., the average precipitate size decreased with increasing aging time. Reverse coarsening slows the coarsening rate of the precipitates, increases the hardness of the alloy, and greatly improves the morphological stability of the γ′ phase.     

Microstructure and growth kinetics of silicide coatings for TiAl alloy

In order to improve the oxidation resistance of Ti Al alloy, silicide coatings were prepared by pack cementation method at 1273, 1323, and 1373 K for 1-3 hours. Scanning electron microscopy(SEM), energy dispersive spectrometry(EDS) and X-ray diffraction(XRD) were employed to investigate the microstructures and phase constitutions of the coatings. The experimental results show that all silicon deposition coatings have multi-layer structure. The microstructure and composition of silicide coatings strongly depend on siliconizing temperatures. In order to investigate the rate controlling step of pack siliconizing on Ti Al alloy, coating growth kinetics was analyzed by measuring the mass gains per unit area of silicided samples as a function of time and temperature. The results showed that the rate controlling step was gas-phase diffusion step and the growth rate constant(k) ranged from 1.53 mg~2/(cm~4·h~2) to 2.3 mg~2/(cm~4·h~2). Activation energy(Q) for the process was calculated as 109 k J/mol, determined by Arrhenius' equation: k = k0 exp[–Q/(RT)].     

Effect of Constituent Core-sizes on Microstructure and Dielectric Properties of BaTiO<Subscript>3</Subscript>@(0.6Ba-TiO<Subscript>3</Subscript>-0.4BiAlO<Subscript>3</Subscript>) Core-Shell Material

The fundamental characteristics of varied initial core-sizes of BaTiO₃(BT) and its influential role on the morphology and dielectric properties of BaTiO₃@0.6BaTiO₃-0.4BiAlO₃(BT@0.6BT-0.4BA) ceramic samples were studied. Alkoxide sol-precipitation method was adopted as revised chemical route to synthesize the constituent “core” BT powders in a dispersed phase, whereas the distinctive initial nano-sized particles were affected by the pre-calcination temperatures (600-900 °C).The microstructure of the uncoated BT ceramics revealed an exaggerated grain growth with an optimized dielectric constant (ε_max >9 000) whilst the coated ceramics behaved otherwise (grain growth inhibited) when sintered at an elevated temperature. Regardless of the previously studied solubility limit (about 0.1%) of BT-BA samples, BT@0.6BT-0.4BA maintained a maximum dielectric constant (ε_max) ranging from 1 592 to 1 708 and tan δ less than 2% under a unit mole ratio at room temperature. In view of all these analyses, the initial nanometer sizes of the as-prepared BT-core powders combined with the increase effect of cation substitutions of Bi³⁺ and Al³⁺ in the shell content, induced the diffuse transition phase of BT@0.6BT-0.4BA composition.     

Crystal growth,structure and properties of bismuth triborate BiB<Subscript>3</Subscript>O<Subscript>6</Subscript> crystal

BiB₃O₆ (BIBO) single crystals with size of 46×23×10 mm³ and weight of 26.0 g have been successfully grown by top-seeded method. Problems encountered in the growth process of this crystal have been discussed in detail, and the methods of growing high-quality large crystals have been put forward. The relationship between their structure and properties is studied. The space group of monoclinic BiB₃O₆ is C2 and the cell parameters are a=7.1203(7) Å, b=4.9948(7) Å, c=6.5077(7) Å, β=105.586(8)″, and V=222.93(5) ų. The density of BIBO is 4.8965 g/cm³. The Mohs’s scale of hardness is 5.5–6. There is no cleavage face in the crystal. The transmittance of BIBO is about 80 percent in the range from visible coherent light to near-infrared light. The ultraviolet cutoff wavelength is at 276 nm. BiB₃O₆ is a biaxial crystal and has two sets of axes, and the relative orientation of (X, Y, Z) with regard to (a, b, c) is: X//b, (Y, c)=47.2°, (Z, a)=31.6°, determined by X-ray analysis combined with polarized microscopy. Second-harmonic-generation (SHG) experiments were carried out for the first time. In type I phase-matching (PM) directions (11.1°, 90°) and (168.9°, 90°), SHG conversion efficiencies of two directions for 1.064 μm light are up to 67.7% and 58%, respectively. We have also obtained the third-harmonic-generation (THG) of 1.064 μm. The comparative experiments between BIBO and KTP were carried out on conversion efficiency, transmittance and hardness. All the above results indicate that BiB₃O₆ is a kind of excellent nonlinear optical (NLO) crystal.     

Comparison of temperature field distribution between cement preclinkering technology and cement precalcining technology

Through the comparison of calcination conditions between cement preclinkering technology and cement precalcining technology,we studied the characteristics of temperature field distribution of cement preclinkering technology systems including cyclone preheater,preclinkering furnace,and rotary kiln.We used numericalsimulation method to obtain data of temperature field distribution.Some results are found by system study.The ratio of tailcoalof cement preclinkering technology is about 70%,and raw mealtemperature can reach 1070 ℃.Shorter L/D kiln type of preclinkering technology can obtain more stable calcining zone temperature.The highest solid temperature of cement preclinkering technology is higher than 80 ℃,and high temperature region(1450 ℃)length is 2 times,which is beneficialfor calcining clinker and higher clinker quality.So cement preclinkering technology can obtain more performance temperature filed,which improves both the solid-phase reaction and liquid-phase reaction.     

Experimental research on the heating performance of a single cylinder refrigerant injection rotary compressor heat pump with flash tank

A single cylinder rotary compressor was applied in the refrigerant injection air-source heat pump to improve the heating performance in cold regions. In this study, the performance of an R410 A single cylinder rotary compressor vapor injection(SCRCVI) system was measured and analyzed by varying the compressor frequency f and injection pressure Pi njat the ambient temperature To d=–10°C.The experimental results indicated that an optimum injection pressure to gain the maximum COP_h (coefficient of performance) existed in the SCRCVI cycle. However, the maximum COP_h of the SCRCVI system decreased as the increase of the frequency, and the maximum COPhwas even lower than that of the CSVC system at high compressor frequency. Therefore, in view of the energy saving and emission reduction, the SCRCVI system should be switched to single stage compression system when the heating capacity demand could be satisfied at high compressor frequency f. Compared to the conventional single-stage vapor compression(CSVC) system, refrigerant injection could enhance the heating capacities and COP_h by 28.2% and 7.91%, respectively. The average total mass flow rate of the SCRCVI system was 24.68% higher than that of the CSVC system. As the SCRCVI system worked at the optimum injection pressure, the variation trends of the different system parameters were investigated in detail. These trends were reliably used to optimize the refrigerant injection system design and the control strategy. The parameter of(P_(inj)–P_s) could be adopted as the signals to control the opening of the upper stage electronic expansion valve EEV1.     

Low temperature synthesis of amorphous La<Subscript>0.7</Subscript>Zn<Subscript>0.3</Subscript>MnO<Subscript>3</Subscript> films grown on p<Superscript>+</Superscript>-Si substrates and its resistive switching properties

Amorphous La_0.7Zn_0.3MnO₃ (LZMO) films were deposited on p⁺-Si substrates by sol-gel method at low temperature of 450 °C. The Ag/LZMO/p⁺-Si device exhibits invertible bipolar resistive switching and the R _HRS/R _LRS was about 10⁴-10⁶ at room temperature which can be kept over 10³ switching cycles. Better endurance characteristics were observed in the Ag/LZMO/p⁺-Si device, the V _Set and the V _Reset almost remained after 10³ endurance switching cycles. According to electrical analyses, the conductor mechanism was in low resistor state (LRS) governed by the filament conductor and in the high state (HRS) dominated by the traps-controlled space-charge-limited current (SCLC) conductor.     

Effect of pH on crystallization of nanocrystalline zirconia in a microwave-hydrothermal process

Nanocrystalline zirconia (ZrO₂) was synthesized using a microwave-hydrothermal process. The effect of pH on the crystallization of the ZrO₂ powders was investigated. The phase and microstructure of ZrO₂ powders were examined using X-ray diffraction (XRD), Raman spectroscopy, and transmission electron microscopy (TEM). Results show that pure m-ZrO₂ can be obtained at low pH (pH<2). Pure t-ZrO₂ is formed at pH = 7 and 14. The size of the ZrO₂ crystals is in the range of 8-26 nm and decreases with increasing pH. The formation of m-ZrO₂ results from the precipitation of ZrO₂ from solution. The t-ZrO₂ is formed through the in-situ structural rearrangement of amorphous Zr(OH) _x O _y . The stabilization of t-ZrO₂ is attributed to the small crystal size and the adsorption of hydroxy ions on the surfaces of the crystals.     

Statistical study of magnetotail flux ropes near the lunar orbit

Flux-rope/TCR events near the magnetotail lunar orbit(-67R_E GSM X* -39RE) were studied using magnetic-field and plasma data measured by THEMIS B and C between January 2011 and March 2012. The aberrant coordinate GSM*, where the X* axis is rotated 4° relative to GSM-X, was used to count the occurrence rate. The number ratio of earthward to tailward events was about 3:5. Moreover, the event occurrence rate distribution showed a clear dawn-dusk asymmetry distribution, with dusk-side events accounting for 57.98%. A superposed epoch analysis of the flux-rope events showed that earthward events had a shorter duration in the leading than in the trailing part. Earthward events also displayed a lower temperature and a lower flow speed than tailward events. We studied the relationship between the event occurrence rate and geomagnetic activity level even further. The occurrence rate of tailward flux-rope/TCR events increases with increasing AE-index, whereas earthward events occur mainly in the relatively quiet period of geomagnetic activity(AE ~ 100–300 n T). Flux-rope/TCR events identified within a 10 mm time frame were treated as belonging to a single reconnection event. By comparing the occurrence rates of earthward and tailward events along X*, we estimated the most likely location of the near-Earth reconnection site as X* = -36R_E.     

Density function theory study of electronic,optical and thermodynamic properties of CaN<Subscript>2</Subscript>, SrN<Subscript>2</Subscript> and BaN<Subscript>2</Subscript>

We put forward a first-principles density-functional theory about the impact of pressure on the structural and elastic properties of bulk CaN₂, SrN₂ and BaN₂. The ground state properties of three alkaline earth diazenides were obtained, and these were in good agreement with previous experimental and theoretical data. By using the quasi-harmonic Debye model, the thermodynamic properties including the debye temperature Θ _D, thermal expansion coefficient α, and grüneisen parameter γ are successfully obtained in the temperature range from 0 to 100 K and pressure range from 0 to 100 GPa, respectively. The optical properties including dielectric function ε(?), absorption coefficient α(?), reflectivity coefficient R(?), and refractive index n(?) are also calculated and analyzed.     

Dielectric properties of Bi<Subscript>4</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> ceramics by impedance spectroscopic method

Various lead-free ceramics have been investigated in search for new high-temperature dielectrics. In particular, Bi₄Ti₃O₁₂ is a type of ferroelectric ceramics, which is supposed to replace leadcontaining ceramics for its outstanding dielectric properties in the near future. Ferroelectric ceramics of Bi₄Ti₃O₁₂ made by conventional mixed oxide route have been studied by impedance spectroscopy in a wide range of temperature. X-ray diffraction patterns show that Bi₄Ti₃O₁₂ ceramics are a single-phase of ferroelectric Bi-layered perovskite structure whether it is calcined at 800 °C or after sintering production. This study focused on the effect of the grain size on the electric properties of BIT ceramics. The BIT ceramics with different grain sizes were prepared at different sintering temperatures. Grain becomes coarser with the sintering temperature increasing by 50 °C, relative permittivity and dielectric loss also change a lot. When sintered at 1 100 °C, r values peak can reach 205.40 at a frequency of 100 kHz, the minimum dielectric losses of four different frequencies make no difference, all close to 0.027. The values of E _a range from 0.52 to 0.68 eV. The dielectric properties of the sample sintered at 1 100 °C are relatively better than those of the other samples by analyzing the relationship of the grain, the internal stresses, the homogeneity and the dielectric properties. SEM can better explain the results of the dielectric spectrum at different sintering temperatures. The results show that Bi₄Ti₃O₁₂ ceramics are a kind of dielectrics. Thus, Bi₄Ti₃O₁₂ can be used in high-temperature capacitors and microwave ceramics.     

Rheological behaviors of fresh cement pastes with polycarboxylate superplasticizer

The rheologicalbehaviors of fresh cement paste with polycarboxylate superplasticizer were systematically investigated.Influentialfactors including superplasticizer to cement ratio(Sp/C),water to cement ratio(w/c),temperature,and time were discussed.Fresh cement pastes with Sp/Cs in the range of 0 to 2.0% and varied W/Cs from 0.25 to 0.5 were prepared and tested at 0,20 and 40 °C,respectively.Flowability and rheologicaltests on cement pastes were conducted to characterize the development of the rheologicalbehavior of fresh cement pastes over time.The exprimentalresults indicate that the initialflowability and flowability retention over shelf time increase with the growth in superplasticizer dosage due to the plasticizing effect and retardation effect of superplasticizer.Higher temperature usually leads to a sharper drop in initialflowability and flowability retention.However,for the cement paste with high Sp/C or w/c,the flowability is slightly affected by temperature.Yield stress and plastic viscosity show similar variation trends to the flowability under the abovementioned influentialfactors at low Sp/C.In the case of high Sp/C,yield stress and plastic viscosity start to decline over shelf time and the decreasing rate descends at elevated temperature.Moreover,two equations to roughly predict yield stress and plastic viscosity of the fresh cement pastes incorporating Sp/C,w/c,temperature and time are developed on the basis of the existing models,in which experimentalconstants can be extracted from a database created by the rheologicaltest results.     

Temperature dependency of dynamic mechanical properties of cement asphalt paste by DMTA method

We investigated the temperature dependency of the dynamic mechanical properties of cement asphalt paste by the dynamic mechanical thermal analysis(DMTA) method. The experimental results show that the dynamic mechanical properties of cement asphalt pastes are sensitive to temperature due to the inclusion of asphalt, and may go through different states within a temperature range of-40 ℃ to 60 ℃, which is different from that of pure cement and asphalt. As the temperature of the cement asphalt paste increases, a considerable change of dynamic mechanical properties, including storage modulus(E'), loss modulus(E') and loss factor(tand) is observed. Moreover, the influence of asphalt to cement(A/C) ratio on the temperature sensitivity of the dynamic mechanical properties of cement asphalt composites was investigated. The temperature dependency of cement asphalt composites is ascribed to the temperature dependency of the asphalt and its interaction with cement paste. A simple fractional model is proposed to describe the viscoelastic behavior of cement asphalt composites.     

Effects of the annealing heating rate on sputtered aluminum oxide films

Al_xO_y films by DC reactive magnetron sputtering were annealed in air ambient at 500 ℃for 1 h with different heating rates of 5,15,and 25 ℃/min.Then heat treatments at 900 ℃ were carried out on these 500 ℃-annealed films to simulate the high-temperature application environment.Effects of the annealing heating rate on structure and properties of both 500 ℃-annealed and 900 ℃-heated films were investigated systematically.It was found that distinct γ-Al_2O_3 crystallization was observed in the 900 ℃-heated films only when the annealing heating rates are 15 and 25 ℃/min.The 500 ℃-annealed film possessed the most compact surface morphology in the case of 25 ℃/min.The highest microhardness of both 500 ℃-annealed and 900℃-heated films were obtained when the annealing heating rate was 15 ℃/min.