Photocatalytic performance of ZnGa2O4 for degradation of methylene blue and its improvement by doping with Cd

ZnGa₂O₄ powder catalysts, synthesized by a sol–gel process, exhibit high photocatalytic activity for methylene blue (MB) degradation. The pH value at the point of zero charge (pH_pzc) was determined to be 5.9 by a titrations method and MB conversion increased with the increase of the pH value. The valence and conduction band positions were determined at 3.35 V and − 1.45 V (Normal Hydrogen Electrode, NHE), respectively, indicating high photocatalytic ability. Improved photocatalytic efficiency was achieved by substituting cadmium for zinc in the ZnGa₂O₄. The improvement can be attributed to high UV absorption efficiency and high separation of photogenerated electron-hole pairs.     

Mn2O3/TiO2 nanofibers with broad-spectrum antibiotics effect and photocatalytic activity for preliminary stage of water desalination

Composite nanofibers consisting of Mn₂O₃ and TiO₂ were prepared by the electrospinning process, and tested as Gram-class-independent antibacterial agent and photocatalyst for organic pollutants degradation. Initially, electrospinning of a sol–gel consisting of titanium isopropoxide, manganese acetate tetrahydrate and poly(vinyl pyrrolidone) was used to produce hybrid polymeric nanofibers. Calcination of the obtained nanofibers in air at 650 °C led to produce good morphology Mn₂O₃/TiO₂ nanofibers. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were employed to characterize the as-spun nanofibers and the calcined product. X-ray powder diffractometry (XRD) analysis was also used to characterize the chemical composition and the crystallographic structure of the sintered nanofibers. The antibacterial activity of Mn₂O₃/TiO₂ nanofibers against Gram negative and Gram positive bacteria was investigated by calculating the minimum inhibitory concentration after treatment with the nanofibers. Investigations revealed that the lowest concentration of Mn₂O₃/TiO₂ nanofibers solution inhibiting the growth of Staphylococcus aureus ATCC 29231 and Escherichia coli ATCC 52922 strains is 0.4 and 0.8 μg/ml, respectively. Incorporation of Mn₂O₃ significantly improved the photodegradation of methylene blue (MB) dye under the visible light irradiation due to enhancing rutile phase formation in the TiO₂ nanofibers matrix.     

FTIR study of NO, C3H6 and O2 adsorption and interaction on gold modified MCM-41 materials

This paper is devoted to the detailed FTIR study of the adsorption, co-adsorption, and interaction of all the reagents used in NO HC-SCR process addressed to lean-burn engines with the surface of new gold catalysts based on ordered mesoporous materials. Gold was introduced into silicate and niobiosilicate matrices by the impregnation (Au/MCM-41 and Au/NbMCM-41, respectively) and via co-precipitation with siliceous and niobium sources (AuNbMCM-41). The in situ FTIR study allowed the estimation of the possible chemisorption of the reagents and their interaction towards intermediates, depending on the chemical composition of the catalyst and the way of gold introduction. It has been found that propene is chemisorbed, but not, NO, on gold species at room temperature. Chemisorbed C₃H₆ interacts with NO only in the presence of oxygen excess. Oxygen oxidizes NO to NO₂, the latter interacts with chemisorbed propene towards carboxylates (1570 cm⁻¹) and NO₂ is reduced to N₂O. At higher temperatures carboxylates interact with gaseous NO to carbonate, N₂O, CO and CO₂. The presence of niobium in the NbMCM-41 matrix enhances the oxidative properties of the catalysts and as a consequence the interaction between intermediates in NO reduction with propene in the oxygen excess. The co-precipitated AuNbMCM-41 exhibits higher NOx storage properties than the impregnated one.     

Carbothermal synthesis, spectral and magnetic characterization and Li-cyclability of the Mo-cluster compounds, LiYMo3O8 and Mn2Mo3O8

The molybdenum cluster compounds, LiYMo₃O₈ and Mn₂Mo₃O₈ are prepared by the carbothermal reduction method and characterized by various techniques. The FT-IR at ambient temperature (RT), and Raman spectra at various temperatures (78-450 K) are reported for the first time and results are interpreted. Magnetic studies on Mn₂Mo₃O₈ in the temperature range, 10-350 K confirm that it is ferrimagnetic, with T_C = 39 K. Magnetic hysteresis and magnetization data at various fields and temperatures are presented. The Li-cyclability is investigated by galvanostatic cycling in the voltage range, 0.005-3.0 V vs. Li at 30 mA/g (0.08 C). LiYMo₃O₈ shows a total first-discharge capacity of 305 ±5 mAh/g whereas the first-charge capacity is only 180 mAh/g at RT. However, both values increased systematically with an increase in the cycle number and yielded a reversible capacity of 385 ±5 mAh/g at the end of 120th cycle. At 50 °C, the reversible capacity is 418 ±5 mAh/g at the 60th cycle. The coulombic efficiency ranges from 94% to 98%. The Li-cyclability behavior of Mn₂Mo₃O₈ is entirely different from that of LiYMo₃O₈. The total first-discharge and charge capacities are 710 ± 5 and 565 ±5 mAh/g, but drastic capacity-fading occurs during cycling. The reversible capacity at the end of 50th cycle is only 205 ±5 mAh/g. Plausible reaction mechanisms are proposed and discussed based on the galavanostatic cycling, cyclic voltammetry, ex situ XRD, ex situ TEM and impedance spectral data.     

Al2O3-coated SnO2/TiO2 composite electrode for the dye-sensitized solar cell

A novel Al₂O₃-coated SnO₂/TiO₂ composite electrode has been applied to the dye-sensitized solar cell. In such an electrode, two kinds of energy barriers (SnO₂/TiO₂ and TiO₂/Al₂O₃) were designed to suppress the recombination processes of the photo-generated electrons and holes. After the SnO₂ was modified by colloid TiO₂, the photoelectric conversion efficiency of the SnO₂/TiO₂ composite cell increased to 2.08% by a factor of 2.8 comparing with that of the SnO₂ cell. The Al₂O₃ layer on the SnO₂/TiO₂ composite electrode further suppressed the generation of the dark current, resulting in 37% improvement in device performance comparing with the SnO₂/TiO₂ cell.     

Fabrication of graphene/prussian blue composite nanosheets and their electrocatalytic reduction of H2O2

In this work, graphene/prussian blue (PB) composite nanosheets with good dispersibility in aqueous solutions have been synthesized by mixing ferric-(III) chloride and potassium ferricyanide in the presence of graphene under ambient conditions. Transmission electron microscopy (TEM) shows that the average size of the as-synthesized PB nanoparticles on the surface of graphene nanosheets is about 20 nm. Fourier-transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD) patterns have been used to characterize the chemical composition of the obtained graphene/PB composite nanosheets. The graphene/PB composite nanosheets exhibit good electrocatalytic behavior to detection of H₂O₂ at an applied potential of −0.05 V. The sensor shows a good linear dependence on H₂O₂ concentration in the range of 0.02-0.2 mM with a sensitivity of 196.6 μA mM⁻¹ cm⁻². The detection limit is 1.9 μM at the signal-to-noise ratio of 3. Furthermore, the graphene/PB modified electrode exhibits freedom of interference from other co-existing electroactive species. This work provides a new kind of composite modified electrode for amperometric biosensors.     

Laser machining of Al2O3-ZrO2 (3%Y2O3) eutectic composite

In this work we present the study of the interaction between NIR pulsed laser and Al₂O₃-ZrO₂ (3%Y₂O₃) eutectic composite. The effect produced by modifying the reference position as well as the working conditions and laser beam features has been studied when the samples are processed by means of pulse bursts.The samples were obtained by the laser floating zone technique using a CO₂ laser system. The laser machining was carried out with a Q-switched Nd:YAG laser at its fundamental wavelength of 1064 nm with pulse-widths in the nanosecond range.Geometric dimensions, i.e. ablated depth, machined width and removed volume as well as ablation yield of the resulting holes have been studied. We have described and discussed the morphology, composition and microstructure of the processed samples.     

Preparation of ZrO2/Gd2O3 composite ceramic materials by coprecipitation method

High burnup is a goal for further development of advanced nuclear power in the future. However, along with the increase of burnup, it becomes more diffidult to control reactor reactivity, which affects the operation safety of the nuclear reactor. Al₂O₃/B₄C burnable poison materials widely used in pressurized water reactor currently will not meet the requirements of burnable poison materials in high burnup nuclear power. Because of the better performance of ZrO₂/Gd₂O₃ burnable poison materials than that of Al₂O₃/B₄C, this paper studies the preparation of ZrO₂/Gd₂O₃ composite ceramic materials by the coprecipitation method. The experimental results show that at the sintering temperature of 1500–1650 °C, ZrO₂/Gd₂O₃ composite ceramic grains are small, compact and uniform with the generation of homogeneous solid solution. At 1600 °C, ZrO₂–10%Gd₂O₃ has the highest density and mechanical strength.     

Study of intrinsic sulfidation behavior of Fe2O3 for high temperature H2S removal

Iron-based sorbent was preferable for desulfurization from coal-derived gas due to economic consideration and favorable dynamic property. The intrinsic behavior of Fe-based sorbent should be primarily understood in the sulfidation process for improving its performance. A series of tests were carried out with Fe₂O₃, Fe and other compounds containing-Fe (FO) made from the same precursor FeC₂O₄·2H₂O in H₂S-N₂ mixture in this study. The formation of H₂ was observed with Fe and FO as sorbents. While SO₂ was detected with FO and Fe₂O₃ as sorbents, its concentration in outlet was gradually decreased. The crystal phase and surface chemical state of fresh and sulfided Fe₂O₃ with different reaction times were characterized by XRD and XPS measurements. The result suggested that the intrinsic H₂S removal by Fe₂O₃ would produce multi-phase of sulfides. The possible mechanism of sulfidation reaction was discussed.     

Cobalt oxide nanoparticles on mesoporous MCM-41 and Al-MCM-41 by supercritical CO2 deposition

CoO and Co₃O₄ nanoparticles were uniformly dispersed inside mesoporous MCM-41 and Al-MCM-41 supports using supercritical CO₂ reactive deposition. This method represents a one-pot reproducible procedure that allows the dissolution of the organocobalt precursor and supports impregnation in supercritical CO₂ at 70 °C and 110 bar, followed by the precursor thermal decomposition into cobalt species at 200 °C and 160 bar. By the relative concentration of the cobalt precursor [cobalt (II) bis (η⁵-ciclopentadienil)], the load of cobalt nanoparticles was controlled and then determined by Inductively Coupled Plasma (ICP-OES). The synthesis of CoO and Co₃O₄ species inside the MCM-41 and Al-MCM-41 substrates was confirmed by X-ray Photoelectron (XPS) and Laser Raman Spectroscopies (LRS). By N₂ adsorption and Small Angle X-ray Scattering (SAXS), it was determined that the hexagonal arrangement as well as the surface area and pore size of the substrates changed after the addition of cobalt. By means of X-ray mapping from SEM images, a homogeneous distribution of cobalt nanoparticles was observed inside the mesopores when the cobalt loading was 1 wt.%. In addition, spherical cobalt nanoparticles of average diameter close to 20 nm were detected on the outer surface of MCM-41 and Al-MCM-41 supports when the cobalt content was higher. On the other hand, by Transmission Electron Microscopy (TEM), it was possible to measure the interplanar distance of the crystalline plane of the outer nanoparticles, which was later compared with the theoretical distance values which allowed identifying the CoO and Co₃O₄ phases.     

Sintering of Al2O3-SiC composite from sol-gel method with MgO, TiO2 and Y2O3 addition

Al₂O₃-SiC composite ceramics were prepared by pressureless sintering with and without the addition of MgO, TiO₂ and Y₂O₃ as sintering aids. The effects of these compositional variables on final density and hardness were investigated. In the present article at first α-Al₂O₃ and β-SiC nano powders have been synthesized by sol-gel method separately by using AlCl₃, TEOS and saccharose as precursors. Pressureless sintering was carried out in nitrogen atmosphere at 1600 °C and 1630 °C. The addition of 5 vol.% SiC to Al₂O₃ hindered densification. In contrast, the addition of nano MgO and nano TiO₂ to Al₂O₃-5 vol.% SiC composites improved densification but Y₂O₃ did not have positive effect on sintering. Maximum density (97%) was achieved at 1630 °C. Vickers hardness was 17.7 GPa after sintering at 1630 °C. SEM revealed that the SiC particles were well distributed throughout the composite microstructures. The precursors and the resultant powders were characterized by XRD, STA and SEM.     

Accommodation of impurities in α-Al2O3, α-Cr2O3 and α-Fe2O3

Atomic scale computer simulation was used to predict the mechanisms and energies associated with the accommodation of aliovalent and isovalent dopants in three host oxides with the corundum structure. Here we consider a much more extensive range of dopant ions than has previously been the case. This enables a rigorous comparison of calculated mechanism energetics. From this we predict that divalent ions are charge compensated by oxygen vacancies and tetravalent ions by cation vacancies over the full range of dopant radii. When defect associations are included in the model these conclusions remain valid. At equilibrium, defects resulting from extrinsic dopant solution dominate intrinsic processes, except for the largest dopant cations. Solution reaction energies increase markedly with increasing dopant radius. The behaviour of cluster binding energies is more complex.     

Effect of Y2O3 and Er2O3 co-dopants on phase stabilization of bismuth oxide

Bi₂O₃ compositions were prepared to investigate the effect of rare earth metal oxides as co-dopants on phase stability of bismuth oxide. Compositions containing 9-14 mol% of Y₂O₃ and Er₂O₃ were synthesized by solid state reaction. The structural characterization was carried out using X-ray powder diffraction. The XRD results show that the samples containing 12 and 14 mol% total dopants had cubic structure, whereas the samples with lower dopant concentrations were tetragonal. Comparing the lattice parameters of the cubic phases of (Bi₂O₃)_0.88(Y₂O₃)_0.06(Er₂O₃)_0.06 and (Bi₂O₃)_0.86(Y₂O₃)_0.07(Er₂O₃)_0.07 revealed that lattice parameter decreases by increasing the dopant concentration. The XRD pattern and the powder density results indicated the formation of solid solution in the studied systems. After annealing samples with cubic phase at 600 °C for various periods of time, phase transformation to tetragonal and rhombohedral occurs.     

Phase diagram of the Al2O3-HfO2-Y2O3 system

The phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system was first constructed in the temperature range 1200-2800 °C. The phase transformations in the system are completed in eutectic reactions. No ternary compounds or regions of appreciable solid solution were found in the components or binaries in this system. Four new ternary and three new quasibinary eutectics were found. The minimum melting temperature is 1755 °C and it corresponds to the ternary eutectic Al₂O₃ + HfO₂ + Y₃Al₅O₁₂. The solidus surface projection, the schematic of the alloy crystallization path and the vertical sections present the complete phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system.     

Corrosion mechanisms of Al2O3/MgAl2O4 by V2O5, NiO, Fe2O3 and vanadium slag

The effects of V₂O₅, NiO, Fe₂O₃ and vanadium slag on the corrosion of Al₂O₃ and MgAl₂O₄ have been investigated. The specimens of Al₂O₃ and MgAl₂O₄ with the respective oxides above mentioned were heated at 10 °C/min from room temperature up to three different temperatures: 1400, 1450 and 1500 °C. The corrosion mechanisms of each system were followed by XRD and SEM analyses. The results obtained showed that Al₂O₃ was less affected by the studied oxides than MgAl₂O₄. Alumina was only attacked by NiO forming NiAl₂O₄ spinel, while the MgAl₂O₄ spinel was attacked by V₂O₅ forming MgV₂O₆. It was also observed that Fe₂O₃ and Mg, Ni, V and Fe present in the vanadium slag diffused into Al₂O₃. On the other hand, the Fe₂O₃ and Ca, S, Si, Na, Mg, V and Fe diffused into the MgAl₂O₄ structure. Finally, the results obtained were compared with those predicted by the FactSage software.     

Characterisation of PEO-Al2O3 composite polymer electrolytes

The behaviour of PEO₈LiClO₄ with different quantities of α-Al₂O₃ or γ-Al₂O₃ was investigated using DSC, AC conductivity and ⁷Li NMR experiments. DSC results showed that the presence of the filler does not change the glass transition temperature of the electrolyte but, on the other hand, modifies the quantity of its crystalline phase. From the AC impedance measurements, it was observed that the sample with the highest conductivity at room temperature is PEO₈LiClO₄ 5.3 wt.% α-Al₂O₃. The change in the quantity of crystalline phase cannot alone explain the conductivity data, and it is suggested that the space charge contribution in the interphase of the filler particles and the polymeric chains influences the behaviour of the samples. The ⁷Li NMR results showed that line width narrowing begins at temperatures close to T_g. From the hydrogen decoupling experiments it was possible to estimate the LiH average distances as 2.7 Å. The LiLi distance was calculated as being between 2.6 and 3.5 Å depending on the number of near neighbours lithium nuclei used in the model.     

The catalytic performance in oxidative coupling of methane and the surface basicity of La2O3, Nd2O3, ZrO2 and Nb2O5

The catalytic performance in oxidative coupling of methane (OCM) of unmodified pure La₂O₃, Nd₂O₃, ZrO₂ and Nb₂O₅ has been investigated under various conditions. The results confirmed that the activity of La₂O₃ and Nd₂O₃ was always much higher than that of the remaining two. The surface basicity/base strength distribution of pure La₂O₃, Nd₂O₃, ZrO₂ and Nb₂O₅ was measured using a test reaction of transformation of 2-butanol and a temperature-programmed desorption of CO₂. Both methods showed that La₂O₃ and Nd₂O₃ had high basicity and contained medium and strong basic sites (lanthanum oxide more and neodymium oxide somewhat less). ZrO₂ had only negligible amount of weak basic sites and Nb₂O₅ was rather acidic. The confrontation of the basicity and catalytic performance indicated that in the case of investigated oxides, the basicity (especially strong basic sites) could be a decisive factor in determination of the catalytic activity in OCM. Only in the case of ZrO₂ it was observed a moderate catalytic performance in spite of negligible basicity. The influence of a gas atmosphere used in the calcination of oxides (flowing oxygen, helium and nitrogen) on their basicity and catalytic activity in OCM had been also investigated. Contrary to earlier observations with MgO, no effect of calcination atmosphere on the catalytic performance of investigated oxides in OCM and on their basicity was observed.     

Microstructure evolution of Al2O3/Al2O3 joint brazed with Ag-Cu-Ti + B + TiH2 composite filler

Al₂O₃/Al₂O₃ joint was achieved using Ag-Cu-Ti + B + TiH₂ composite fillers at 900 °C for 10 min. The evolution mechanism of interface during brazing was discussed. Effects of Ti and B atoms content on microstructure of joints were investigated. Results show that a continuous and compact reaction layer Ti₃(Cu,Al)₃O forms at Al₂O₃/brazing alloy interface. Ti(Cu,Al) precipitates near Ti₃(Cu,Al)₃O layer. In situ synthesized TiB whiskers evenly distribute in Ag and Cu based solid solution. The higher content of B powders in composite fillers increases TiB whiskers content, but decreases the thickness of Ti₃(Cu,Al)₃O layer, while the higher TiH₂ powders content thickens Ti₃(Cu,Al)₃O layer. Ag and Cu based solid solutions become uniform and fine with the increasing of TiB whiskers content. Ti(Cu,Al) intermetallics content increase and they gradually distribute from Al₂O₃ side to the central of brazing alloy, but the content of Cu based solid solution decreases when the TiH₂ content increases.     

Structural and optical properties of Tm:Y2O3 transparent ceramic with La2O3, ZrO2 as composite sintering aid

The paper reports the use of La₂O₃ and ZrO₂ co-doping as a composite sintering aid for the fabrication of Tm:Y₂O₃ transparent ceramics. Two groups of experiments were conducted for investigating the influences of composite sintering aids on the microstructures and the optical properties of Tm:Y₂O₃ transparent ceramics in contrast to single La³⁺ and single Zr⁴⁺ doped Tm:Y₂O₃. Samples with composite sintering aids could realize fine microstructures and good optical properties at relatively low sintering temperatures. Grain sizes around 10 μm and transmittances close to theoretical value at wavelength of 2 μm were achieved for the 9 at.% La³⁺, 3 at.% Zr⁴⁺ co-doped samples sintered at 1500-1600 °C. The influences of the composite sintering aids on the emission intensities and the phonon energies of Tm:Y₂O₃ ceramics were also investigated.