Microwave dielectric properties of Ba3Ti4−x(Zn1/3Nb2/3)xNb4O21 for low temperature co-fired ceramics

The effects of substitution of (Zn_1/3Nb_2/3) for Ti on the sintering behavior and microwave dielectric properties of Ba₃Ti_4−x(Zn_1/3Nb_2/3)_xNb₄O₂₁ (0 ≤ x ≤ 4) ceramics have been investigated. The dielectric constant (?_r) and the temperature coefficient of the resonant frequency (τ_f) of Ba₃Ti_4−x(Zn_1/3Nb_2/3)_xNb₄O₂₁ ceramics decreased with increasing x. However, the Q × f values enhanced with the substitution of (Zn_1/3Nb_2/3) for Ti. It was found that a small amount of MnCO₃-CuO (MC) and ZnO-B₂O₃-SiO₂ (ZBS) glass additives to Ba₃Ti_4−x(Zn_1/3Nb_2/3)_xNb₄O₂₁ (x = 2) ceramics lowered the sintering temperature from 1250 to 900 °C. And Ba₃Ti_4−x(Zn_1/3Nb_2/3)_xNb₄O₂₁ (x = 2) ceramics with 1 wt% MC and 1 wt% ZBS sintered at 900 °C for 2 h showed excellent dielectric properties: ?_r = 53, Q × f = 14,600 GHz, τ_f = 6 ppm/°C. Moreover, it has a chemical compatibility with silver, which made it as a promising material for low temperature co-fired ceramics technology application.     

Dielectric and impedance spectroscopy of Sr(Bi0.5Nb0.5)O3 ceramics

A lead free polycrystalline material Sr(Bi_0.5Nb_0.5)O₃ was prepared using a high-temperature solid-state reaction technique. Preliminary X-rays diffraction studies exhibit the formation of a single-phase compound in the orthorhombic crystal system. The study of microstructure of gold-coated pellet by scanning electron microscopy (SEM) shows well-defined and homogeneous distribution of grains on the surface of the sample. Detailed studies of dielectric parameters (i.e., ε_r and tan δ) of the compound as a function of temperature at selected frequencies reveal that the values of these parameters are almost independent of temperature. Studies of impedance and related parameters exhibit that these electrical properties of the material are strongly dependent on temperature, and bear a good correlation with the microstructure of the material. The decrease in value of bulk resistance on increasing temperature suggests the existence of negative temperature co-efficient of resistance (NTCR) in the material. Studies of electric modulus show the presence of hopping conduction mechanism in the material with non-exponential-type of relaxation. The nature of variation of dc conductivity with temperature confirms the Arrhenius- and NTCR- types of behaviors of the material. The ac conductivity spectrum provides a typical-signature of an ionic conducting system, and is found to obey Jonscher′s universal power law.     

Enhancement in dielectric and ferroelectric properties of lead free Bi0.5(Na0.5K0.5)0.5TiO3 ceramics by Sb-doping

Lead free piezoelectric Bi_0.5(Na_0.5K_0.5)_0.5TiO₃ (pure and 1 wt.%, 2 wt.%, 4 wt.% Sb-doped) ceramics were synthesized away from its MPB. The crystalline nature of the BNKT ceramic was studied by XRD and SEM. Depolarization temperature (T_d) and transition temperature (T_c) were observed through phase transitions in dielectric studies which were found to increase after Sb-doping, thus increasing its usable temperature range. In the study of relaxation behavior, the activation energy for relaxation was found to be 0.33, 0.43, 0.57 and 0.56 eV for pure and Sb-doped samples, respectively. All samples were found to exhibit normal Curie-Weiss law above their T_c. Doping of Sb was found to restrain the diffused character of the pure sample. In P-E loop, Sb-doping was found to increase the ferroelectric properties.Pure and Sb-doped BNKT ceramics exhibited high values of piezoelectric charge coefficient (d₃₃) as 115, 121, 129 and 100 pC/N, respectively.     

Adjustable dielectric properties of Li2CuxZn1−xTi3O8 (x=0 to 1) ceramics with low sintering temperature

Single-phase dielectric ceramics Li₂Cu_xZn_1−xTi₃O₈ (x=0–1) were synthesized by the conventional solid-state ceramic route. All the solid solutions adopted Li₂MTi₃O₈ cubic spinel structure in which Li/M and Ti show 1:3 order in octahedral sites whereas Li and M are distributed randomly in tetrahedral sites with the degree of Li/M cation mixing varying from 0.5 to 0.3. The substitution of Cu for Zn effectively lowered the sintering temperatures of the ceramics from 1050 to 850 °C and significantly affected the dielectric properties. As x increased from 0 to 0.5, τ_f gradually increased while the dielectric constant (ε_r) and quality factor value (Q×f) gradually decreased, and a near-zero τ_f of 1.6 ppm/°C with ε_r of 25.2, Q×f of 32,100 GHz could be achieved for Li₂Cu_0.1Zn_0.9Ti₃O₈ ceramic sintered at 950 °C, which make it become an attractive promising candidate for LTCC application. As x increases from 0.5 to 1, the dielectric loss significantly increases with AC conductivity increasing up to 2.3×10⁻⁴ S/cm (at 1 MHz).     

Structural,magnetic and dielectric behavior of Mg1−xCaxNiyFe2−yO4 nano-ferrites synthesized by the micro-emulsion method

Ca–Ni co-substituted samples of nanocrystalline spinel ferrites with chemical formula Mg_1−xCa_xNi_yFe_2−y O₄ (x=0.0–0.6, y=0.0–1.2) were synthesized by the micro-emulsion method and were annealed at 700 °C for 7 h. The synthesized samples were characterized by x-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, vibrating sample magnetometry (VSM) and dielectric measurements. The XRD and FTIR analysis reveals that single phase samples can be achieved by substituting Ca and Ni ions at Mg and Fe sites respectively in cubic spinel nano-ferrites. The crystallite size of the synthesized samples was found in the range 29–45 nm. The saturation magnetization (M_s) increases from 9.84 to 24.99 emu/g up to x=0.2, y=0.4 and then decreases, while the coercivity (H_c) increases continuously from 94 to 153 Oe with the increase in dopants concentration. The dielectric properties of these nano materials were also studied at room temperature in the frequency range 100 MHz to 3 GHz. The dielectric parameters were found to decrease with the increased Ca–Ni concentration. Further the peaking behavior was observed beyond 1.5 GHz. The frequency dependent dielectric properties of all the samples have been explained qualitatively on the basis of the Maxwell–Wagner two-layer model according to Koop's phenomenological theory. The enhanced magnetic parameters and reduced dielectric properties make the synthesized materials suitable for switching and high frequency applications, respectively.     

Moisture sensitivity of YCr(1−x)MnxO3 perovskites

This work deals with the sensitivity to moisture rate in air of perovskite with general formula YCr_(1−x)Mn_xO₃ with x ranging from 0 to 0.8. The combined sensitivity to moisture and temperature let us think the possibility of realizing composite sensors temperature/moisture. This study clearly shows the influence of the Mn content on moisture which affects the working frequency of sensors. Capacitance variation of the most sensitive compositions increases from 100 pF to 1 nF for relative humidity between 20 and 80%. The influence of porosity is also demonstrated.     

Higher permittivity of Ni-doped lead zirconate titanate,Pb[(Zr0.52Ti0.48)(1-x) Nix]O3, ceramics

The paper reports highest obtained dielectric constant for Ni-doped Lead Zirconate Titanate [PZT, Pb(Zr_0.52Ti_0.48)O₃] ceramics. The Ni-doped PZT ceramic pellets were prepared via conventional solid-state reaction method with Ni content chosen in the range 0–20?at%. X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy were employed to investigate the crystal structure of the prepared ceramics. The X-ray diffraction analysis indicated that the ceramic pellets had crystallized into tetragonal perovskite structure. A minute displacement of XRD peaks was detected in the diffraction spectra of Ni-doped PZT ceramic samples which when examined by size-strain plot (SSP) method revealed presence of homogenous strain that decreased with increase in concentration of Ni. In FTIR the maximum absorption at 597?cm^?1, 608?cm^?1, 611?cm^?1, 605 and 613?cm^?1 for Ni?=?0, 5, 10, 15 and 20?at%, respectively, confirmed the formation of perovskite structure in all the compositions and the slight shift suggests decrease in cell size on doping. The values of dielectric constant (ε′) & tanδ as a function of frequency and temperature were measured for the prepared ceramics and it revealed highest ever reported dielectric constant for Ni - doped PZT with Ni?=?5?at%. The dielectric variation with temperature exhibited a diffused type ferroelectric–paraelectric phase transition for the doped samples. Also, the maximum dielectric constant value (ε′_max) decreased while the phase transition temperature increased with increase in doping concentration of Ni. The estimated activation energy of different compositions was found to increase from 0.057 to 0.068?eV for x?=?0.00 to x?=?0.20 in ferroelectric phase. The piezoelectric, ferroelectric and magnetic properties were also investigated.     

Microwave dielectric properties of BaO-2(1 − x)ZnO-xNd2O3-4TiO2 (x = 0-1.0) ceramics

Microwave dielectric properties of (1 − x)BaZn₂Ti₄O₁₁-xBaNd₂Ti₄O₁₂ (x = 0-1.0) ceramics were investigated by the solid-state reaction with the purpose of finding a microwave ceramics with high dielectric constant (?_r), high quality factor (Q × f) and low temperature coefficient of resonant frequency (τ_f). A two phase system BaZn₂Ti₄O₁₁-BaNd₂Ti₄O₁₂ was formed and SEM photographs show equiaxed BaZn₂Ti₄O₁₁ grains and columnar BaNd₂Ti₄O₁₂ grains. The microwave dielectric properties were strongly determined by the chemical composition. As increasing x from 0 to 1.0, the phase composition varied from pure BaZn₂Ti₄O₁₁, to the two phase system BaZn₂Ti₄O₁₁-BaNd₂Ti₄O₁₂ and then to pure BaNd₂Ti₄O₁₂. Therefore, the ?_r raised from 29.1 to 82.0 and the Q × f values decreased from 54,630 GHz to 8110 GHz, and the τ_f values increased from −29 ppm/°C to 94 ppm/°C. 0.8BaZn₂Ti₄O₁₁-0.2BaNd₂Ti₄O₁₂ ceramics sintered at 1250 °C for 2.5 h had ?_r = 39.1, Q × f = 37,850 GHz and τ_f = −9 ppm/ °C.     

Effect of La substitution on the structural and electrical properties of BaBi4−xLaxTi4O15

Pure and lanthanum doped barium bismuth titanate BaBi_4−xLa_xTi₄O₁₅ (BBLT, x=0, 0.05, 0.15, 0.30) ceramics were prepared utilizing solid state method. The X-ray diffraction (XRD) data confirmed formation of single-phase Aurivillius compounds while SEM micrographs did not show evident grain size change of doped ceramics. Dielectric properties were investigated in 1.21 kHz to 1 MHz frequency range and in the temperature range of 20 to 727 °C. When Bi³⁺ is substituted with La³⁺, a significant disorder was induced and the material exhibited broadening of the phase transition. Impedance analysis confirmed the presence of two semicircular arcs in doped samples suggesting the existence of grain and grain-boundary conduction. The dc-conductivity and activation energies were evaluated for all compositions.     

Enhanced ferroelectric properties in (Ba1−xCax)(Ti0.94Sn0.06)O3 lead-free ceramics

Lead-free (Ba_1−xCa_x)(Ti_0.94Sn_0.06)O₃ (BCST) (x = 0.01-0.04) ceramics were prepared using a solid-state reaction technique. The effects of Ca content on the phase structure and electrical properties of the BCST ceramics were investigated. High piezoelectric coefficient of d₃₃ = 440 pC/N, planar electromechanical coupling factor of k_p = 45% and dielectric constant ?_r = 6900 were obtained for the samples at x = 0.03. At room temperature, a polymorphic phase transition (PPT) from orthorhombic phase to tetragonal phase was identified in the composition range of 0.02 < x < 0.04.     

Enhanced dielectric and piezoelectric properties in Na0.5Bi4.5Ti4O15 ceramics with Pr-doping

The bismuth layer-structured Na_0.5Bi_4.5-xPr_xTi₄O₁₅ (x?=?0, 0.1, 0.2, 0.3, 0.4, and 0.5) (NBT-xPr³⁺) ceramics were fabricated using the traditional solid reaction process. The effect of different Pr³⁺ contents on dielectric, ferroelectric and piezoelectric properties of Na_0.5Bi_4.5Ti₄O₁₅ ceramics were investigated. The grain size of Pr³⁺-doping ceramics was found to be smaller than that of pure one, the maximum dielectric constant and Curie temperature T_c gradually decreased with increasing Pr³⁺ contents, and the dielectric loss decreased at high temperature by Pr³⁺-doping. Moreover, the activation energy (E_a), resistivity (Z’), remanent polarization (2P_r) and piezoelectric constant (d₃₃) increased by Pr³⁺-doping. The NBT-xPr³⁺ ceramics with x?=?0.3 achieved the optimal properties with the maximum dielectric constant of 1109.18, minimum loss of 0.00822 (250?kHz), E_a of 1.122?eV, Z’ of 7.9?kΩ?cm (725 ºC), d₃₃ of 18 pC/N, 2P_r of 12.04 μC/cm². The enhancement was due to the addition of Pr³⁺ which suppressed the decreasing of resistivity at high temperature and made it possible for NBT-xPr³⁺ ceramics to be poled in perpendicular direction, implying that it is a great improvement for Na_0.5Bi_4.5Ti₄O₁₅ ceramics in electrical properties.     

Dielectric and impedance spectroscopy of Bi(Ca0.5Ti0.5)O3 ceramic

Bismuth calcium titanate (BiCa_0.5Ti_0.5O₃) ceramic, fabricated by a ceramic processing technique, has been characterized using a variety of experimental techniques. Analysis of basic crystal structure using X-ray diffraction data exhibits the orthorhombic system. Measurements and detailed analysis of some electrical parameters (i.e.,dielectric constant, loss tangent (energy loss), electrical impedance and modulus, conductivity, etc.) of Bi(Ca_0.5Ti_0.5)O₃ in a wide range of frequency (10³–10⁶ Hz) and temperature (30–500 °C) have provided some interesting and useful data and results on structure–properties relationship, conduction mechanism, etc.The role of interface, space charge polarization and Maxwell–Wagner dielectric relaxation in getting high dielectric constant of the material at low frequencies and high temperatures has been discussed. Study of temperature dependence of Nyquist plots clearly shows the contributions of grains in resistive and capacitive properties of the material. The frequency of the applied electric field and temperature strongly affect the dielectric (permittivity and dissipation of energy) and electrical (impedance, electrical modulus and conductivity) characteristics of the material.     

Electrical and photoluminescence properties of Sm3+ doped Na0.5La0.5Bi8-xSmxTi7O27 ceramics

In this study, Sm³⁺ doped Na_0.5La_0.5Bi_8-xSm_xTi₇O₂₇ (NBT-BITL-xSm, x = 0, 0.01, 0.015, 0.02, and 0.03) ceramics were synthesized via a conventional solid-state reaction process. The structural, electrical, and photoluminescence properties of NBT-BITL-xSm ceramics were systematically investigated. The crystal structure of NBT-BITL-xSm was refined using XRD Rietveld refinement and found to possess a single orthorhombic structure at room temperature. Raman spectroscopy revealed that Sm³⁺ ions preferred to substitute for Bi³⁺ located in the A-sites of pseudo-perovskite layers, inducing a slight decrease in orthorhombic distortion. Strong characteristic emission peaks of Sm³⁺ ions were observed in orange-red regions under a 407 nm laser source, and the sample with x = 0.015 achieved the optimal photoluminescent property. Dielectric measurements showed double anomaly permittivity peaks at the temperature of 589 and 600^°C (T_m and T_c, respectively). The complex impedance spectrum indicated that the electrical conductivities mainly originated from crystal grains at high temperature. The activation energy was calculated to be 1.37–1.44 eV from Arrhenius fitting results. After Sm³⁺ substitution, the activation energy for conductivity was increased as a result of reduced oxygen vacancies.     

High energy-storage properties of [(Bi1/2Na1/2)0.94 Ba0.06] La(1−x) ZrxTiO3 lead-free anti-ferroelectric ceramics

Energy-storage properties of [(Bi_1/2Na_1/2)_0.94Ba_0.06]La_(1−x)Zr_xTiO₃ (BNT-BLZT, x=0, 0.02, 0.04, and 0.06) lead-free anti-ferroelectric ceramics fabricated via the conventional sintering technique were first investigated. Calculation from the X-ray diffraction results reveals that BNT-BLZT ceramic possesses a single perovskite structure phase. In addition, the P–E hysteresis loops measured at room temperature show that the BNT-BLZT (x=0.02) ceramics obtain the maximum P value of 37.5 μC/cm² and the largest energy-storage density W_max is 1.58 J/cm³. The temperature dependence of dielectric permittivity ε_r and dielectric loss tanδ illustrate that the addition of Zr can improve the piezoelectric properties of BT-BLZT ceramics. These properties indicate that BNT-BLZT ceramics might be a promising lead-free anti-ferroelectric material for energy storage application.     

Structural and dielectric properties of Bi1−xSrxMnO3 (0.40≤x≤0.55)

In order to study the effect of Sr substitution on structural and dielectric properties of Bi_1−xSr_xMnO₃ (0.40≤x≤0.55) compounds were synthesized by the solid state reaction method. The as-prepared samples were characterized by X- ray diffraction (XRD) and dielectric measurements to correlate structural changes with dielectric properties. The XRD data were further analyzed by the Rietveld refinement. The highest dielectric constant was observed in Bi_0.55Sr_0.45MnO₃ and Bi_0.5Sr_0.5MnO₃ systems (∼10⁶) mainly because of orientation polarization. The charge ordering temperature decreases with increasing Sr concentration in Bi_1−xSr_xMnO₃ systems.     

High energy storage performance of [(Bi0.5Na0.5)0.94Ba0.06]0.97La0.03Ti1-x(Al0.5Nb0.5)xO3 ceramics with enhanced dielectric breakdown strength

Novel lead-free [(Bi_0.5Na_0.5)_0.94Ba_0.06]_0.97La_0.03Ti_1-x(Al_0.5Nb_0.5)_xO₃ ceramics (BNBLT-xAN) were prepared by the conventional solid state sintering method. The dielectric, ferroelectric, ac impedance and energy-storage performance were systematically investigated. Temperature dependent permittivity curves showed that relaxation properties of sintered ceramics gradually diminished with the increase of AN. The introduction of AN gave rise to a slimmer polarization hysteresis loop (P-E) and an enhanced dielectric breakdown strength (DBS). Therefore, the optimum energy-storage performance were realized at x?=?0.05 with the energy-storage density (W_rec) of 1.72?J/cm³ and energy-storage efficiency (η) of 85.6% at 105?kV/cm, accompanied with the excellent temperature stability and fatigue performance. The results demonstrated that BNBLT-xAN system was a promising lead-free candidate for energy-storage applications.     

Effect of Bi2O3 additives on sintering and microwave dielectric behavior of La(Mg0.5Ti0.5)O3 ceramics

Bi₂O₃ was selected as liquid phase sintering aid to lower the sintering temperature of La(Mg_0.5Ti_0.5)O₃ ceramics. The sintering temperature of La(Mg_0.5Ti_0.5)O₃ ceramics is generally high, about 1600 °C. However, the sintering temperature was significantly lowered about 275 °C from 1600 °C to 1325 °C by incorporating in 15 mol% Bi₂O₃ and revealed the optimum microwave dielectric properties of dielectric constant (?_r) value of 40.1, a quality factor (Q × f) value of 60,231 GHz, and the temperature coefficient (τ_f) value of 70.1 ppm/°C. During all addition ranges, the relative dielectric constants (?_r) were different and ranged from 32.0 to 41.9, the quality factors (Q × f) were distributed in the range of 928–60,231 GHz, and the temperature coefficient (τ_f) varies from 0.3 ppm/°C to 70.3 ppm/°C. Noticeably, a nearly zero τ_f can be found for doping 5 mol% Bi₂O₃ sintering at 1325 °C. It implies that nearly zero τ_f can be achieved by appropriately adjusting the amount of Bi₂O₃ additions and sintering temperature for La(Mg_0.5Ti_0.5)O₃ ceramics.     

Sintering and electrical properties of La-modified (Na0.52K0.45Li0.03)1−3xLax(Nb0.88Sb0.09Ta0.03)O3 lead-free ceramics

(Na_0.52K_0.45Li_0.03)_1−3xLa_x(Nb_0.88Sb_0.09Ta_0.03)O₃ (NKLL_xNST) lead-free ceramics were prepared by normal sintering and their dielectric and piezoelectric properties were investigated. The X-ray methods indicate that the NKLL_xNST ceramics with x≤0.003 present a pure perovskite phase at room temperature. The bulk density of NKLL_xNST ceramics increases with proper amount of La₂O₃ contents, and reaches its highest value of 4.544 g/cm³ with the addition of 0.3 mol% La₂O₃. At x=0.003, remnant polarization P_r, piezoelectric constant d₃₃ and planar mode electromechanical coupling factor k_p of NKLL_xNST ceramics reach the highest values of 37.80 μC/cm², 346 pC/N and 40%, respectively, exhibiting excellent “soft” piezoelectric characteristics, demonstrating a tremendous potential of the compositions studied for device applications.     

Dielectric properties of CuO-doped La2.98/3Ba0.01(Mg0.5Sn0.5)O3 ceramics at microwave frequency

The microwave dielectric properties of La_2.98/3Ba_0.01(Mg_0.5Sn_0.5)O₃ ceramics prepared by the conventional solid-state method were investigated for application in mobile communication. A 100 °C reduction of the sintering temperature was obtained by using CuO as a sintering aid. A dielectric constant of 20.0, a quality factor (Q × f) of 50,100 GHz and a temperature coefficient of resonant frequency τ_f of −78.3 ppm/°C were obtained when La_2.98/3Ba_0.01(Mg_0.5Sn_0.5)O₃ ceramics with 0.25 wt.% CuO were sintered at 1500 °C for 4 h.     

The influence of sintering aids for Nd(Mg0.5Ti0.5)O3 microwave dielectric ceramics properties

The influence of various sintering aids on the microwave dielectric properties and the structure of Nd(Mg_0.5Ti_0.5)O₃ ceramics were investigated systematically. B₂O₃, Bi₂O₃, and V₂O₅ were selected as liquid-phase sintering aids to lower the sintering temperature. The sintered Nd(Mg_0.5Ti_0.5)O₃ ceramics are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and microwave dielectric properties. The sintering temperature of Nd(Mg_0.5Ti_0.5)O₃ microwave dielectric ceramics is generally high, about 1500 °C. However, the sintering temperature was significantly lowered about 175 °C from 1500 °C to 1325 °C by incorporating in 10 mol% B₂O₃ and revealed the optimum microwave dielectric properties of dielectric constant (_r) value of 26.2, a quality factor (Q × f) value of 61,307 (at 9.63 GHz), and τ_f value of −45.5 ppm/°C. NdVO₄ secondary phase was observed at 10 mol% V₂O₅ addition in the sintering temperature range of 1300–1325 °C, which led the degradation in microwave dielectric properties. The microwave dielectric properties as well as grain sizes, grain morphology, and bulk density were greatly dependent on sintering temperature and various sintering aids. In this study, it is found that Nd(Mg_0.5Ti_0.5)O₃ incorporated with 10 mol% B₂O₃ with lower sintering temperature and excellent dielectric microwave properties may be suggested for application in microwave communication devices. The use of liquid-phase sintering, the liquid formed during firing normally remains as a grain boundary phase on cooling. This grain boundary phase can cause a deterioration of the microwave properties. Therefore, the selection of a suitable sintering aid is extremely important.