The properties of transparent semiconductor Zn1 − xTixO thin films prepared by the sol-gel method

Transparent semiconductor thin films of Zn_1 − xTi_xO (0 ≦ x ≦ 0.12) were deposited on alkali-free glass substrates by the sol-gel method. The effects of Ti addition on the crystallization, microstructure, optical properties and resistivity of ZnO thin films were investigated. The as-coated films were preheated at 300 °C, and then annealed at 500 °C in air ambiance. X-ray diffraction results showed all polycrystalline Zn_1 − xTi_xO thin films with preferred orientation along the (002) plane. Ti incorporated within the ZnO thin films not only decreased surface roughness but also increased optical transmittance and electrical resistivity. In the present study, the Zn_0.88Ti_0.12O film exhibited the best properties, namely an average transmittance of 91.0% (an increase of ~ 12% over the pure ZnO film) and an RMS roughness value of 1.04 nm.     

Stable p-type conductivity and enhanced photoconductivity from nitrogen-doped annealed ZnO thin film

We report on the growth of p-type ZnO thin films with improved stability on various substrates and study the photoconductive property of the p-type ZnO films. The nitrogen doped ZnO (N:ZnO) thin films were grown on Si, quartz and alumina substrates by radio frequency magnetron sputtering followed by thermal annealing. Structural studies show that the N:ZnO films possess high crystallinity with c-axis orientation. The as-grown films possess higher lattice constants compared to the undoped films. Besides the high crystallinity, the Raman spectra show clear evidence of nitrogen incorporation in the doped ZnO lattice. A strong UV photoluminescence emission at ~ 380 nm is observed from all the N:ZnO thin films. Prior to post-deposition annealing, p-type conductivity was found to be unstable at room temperature. Post-growth annealing of N:ZnO film on Si substrate shows a relatively stable p-type ZnO with room temperature resistivity of 0.2 Ω cm, Hall mobility of 58 cm²/V s and hole concentration of 1.95 × 10¹⁷ cm^− 3. A homo-junction p-n diode fabricated on the annealed p-type ZnO layer showed rectification behavior in the current-voltage characteristics demonstrating the p-type conduction of the doped layer. Doped ZnO films (annealed) show more than two orders of magnitude enhancement in the photoconductivity as compared to that of the undoped film. The transient photoconductivity measurement with UV light illumination on the doped ZnO film shows a slow photoresponse with bi-exponential growth and bi-exponential decay behaviors. Mechanism of improved photoconductivity and slow photoresponse is discussed based on high mobility of carriers and photodesorption of oxygen molecules in the N:ZnO film, respectively.     

Influence of oxygen pressure on the structural, electrical and optical properties of VO2 thin films deposited on ZnO/glass substrates by pulsed laser deposition

The influence of oxygen pressure on the structural and electrical properties of vanadium oxide thin films deposited on glass substrates by pulsed laser deposition, via a 5-nm thick ZnO buffer, was investigated. For the purposes of comparison, VO₂ thin films were also deposited on c-cut sapphire and glass substrates. During laser ablation of the V metal target, the oxygen pressure was varied between 1.33 and 6.67 Pa at 500 °C, and the interaction and reaction of the VO₂ and the ZnO buffer were studied. X-ray diffraction studies showed that the VO₂ thin film deposited on a c-axis oriented ZnO buffer layer under 1.33 Pa oxygen had (020) preferential orientation. However, VO₂ thin films deposited under 5.33 and 6.67 Pa were randomly oriented and showed (011) peaks. Crystalline orientation controlled VO₂ thin films were prepared without such expensive single crystal substrates as c-cut sapphire. The metal-insulator transition properties of the VO₂/ZnO/glass samples were investigated in terms of electrical conductivity and infrared reflectance with varying temperatures, and the surface composition was investigated by X-ray photoelectron spectroscopy.     

p-type doping of ZnO by means of high-density inductively coupled plasmas

A custom-designed inductively coupled plasma assisted radio-frequency magnetron sputtering deposition system has been used to fabricate N-doped p-type ZnO (ZnO:N) thin films on glass substrates from a sintered ZnO target in a reactive Ar + N₂ gas mixture. X-ray diffraction and scanning electron microscopy analyses show that the ZnO:N films feature a hexagonal crystal structure with a preferential (002) crystallographic orientation and grow as vertical columnar structures. Hall effect and X-ray photoelectron spectroscopy analyses show that N-doped ZnO thin films are p-type with a hole concentration of 3.32 × 10¹⁸ cm^− 3 and mobility of 1.31 cm² V^− 1 s^− 1. The current-voltage measurement of the two-layer structured ZnO p-n homojunction clearly reveals the rectifying ability of the p-n junction. The achievement of p-type ZnO:N thin films is attributed to the high dissociation ability of the high-density inductively coupled plasma source and effective plasma-surface interactions during the growth process.     

Study on ZnO thin films deposited on sol-gel grown ZnO buffer by RF magnetron sputtering

ZnO thin films with preferential C-orientation and dense microstructure have been prepared using RF magnetron sputtering method by the insertion of a sol-gel grown ZnO buffer layer. The XRD results show that the C-orientation of the film deposited on ZnO buffer is obviously better than that deposited directly on lime-glass substrate. With an increase of the RF power from 100 to 380 W, C-orientation of the films with ZnO buffer improves and the grain size increases. When the RF power equals 550 W, the orientation of the film changes to (1 0 0) and the grain size decreases. The crystalline and microstructure quality of the films can be improved after annealing, however, the grain size is not much dependent on the annealing temperature in the range of 560-610 °C.     

Effects of surface roughness of substrates on the c-axis preferred orientation of ZnO films deposited by r.f. magnetron sputtering

The c-axis preferred orientation of ZnO film is the most important factor for its successful application in piezoelectric devices. The effects of surface roughness of the substrate on the c-axis preferred orientation of ZnO thin films, deposited by radio frequency magnetron sputtering, were investigated. During sputtering, the oxygen content in the argon environment used was varied from 0 to 70% at a total sputtering pressure of 10 mTorr. Very smooth Si, smooth evaporated Au/Si, smooth evaporated-Al/Si, and rough sputtered-Al/Si were used as substrates. Their r.m.s. roughnesses, as measured by atomic force microscopy, were 1.27, 17.1, 21.1 and 65-118 Å, respectively. The crystalline structure and the angular spread of the (0 0* 2) plane normal to the ZnO films were determined using X-ray diffraction and X-ray rocking curves, respectively. The crystallinity and the preferred c-axis orientation of the ZnO films were strongly dependent on the surface roughness of the substrates rather than on the oxygen content of the working environment or on the chemical nature of the substrate.     

Highly luminescent columnar ZnO films grown directly on n-Si and p-Si substrates by low-temperature electrochemical deposition

In this study, nanocolumnar zinc oxide thin films were catalyst-free electrodeposited directly on n-Si and p-Si substrates, what makes an important junction for optoelectronic devices. We demonstrate that ZnO thin films can be grown on Si at low cathodic potential by electrochemical synthesis. The scanning electron microscopy SEM showed that the ZnO thin films consist of nanocolumns with radius of about 150 nm on n-Si and 200 nm on p-Si substrates, possess uniform size distribution and fully covers surfaces. X-ray diffraction (XRD) measurements show that the films are crystalline material and are preferably grown along (0 0 2) direction. The impact of thermal annealing in the temperature range of 150-800 °C on ZnO film properties has been carried out. Low-temperature photoluminescence (PL) spectra of the as-prepared ZnO/Si samples show the extremely high intensity of the near bandgap luminescence along with the absence of visible emission. The optical quality of ZnO thin films was improved after post-deposition thermal treatment at 150 °C and 400 °C in our experiments, however, the luminescence intensity was found to decrease at higher annealing temperatures (800 °C). The obtained results indicate that electrodeposition is an efficient low-temperature technique for the growth of high-quality and crystallographically oriented ZnO thin films on n-Si and p-Si substrates for device applications.     

Structural and optical characterization of Al-doped ZnO films prepared by thermal oxidation of evaporated Zn/Al multilayered films

Aluminum-doped zinc oxide (ZnO:Al) thin films (t = 68–138 nm) were prepared by thermal oxidation in air flow, at 720 K, of the multilayered metallic Zn/Al thin stacks deposited in vacuum onto glass substrates by physical vapor deposition. The effect of Al content (3.7–8.2 at.%) on the structural (crystallinity, texture, stress, surface morphology) and optical (transmittance, absorbance, energy band gap) characteristics of doped ZnO thin films was investigated. The X-ray diffraction spectra revealed that the Al-doped ZnO films have a hexagonal (wurtzite) structure with preferential orientation with c-axis perpendicular to the substrate surface. A tensile residual stress increasing with Al content was observed. The films showed a high transmittance (about 90%) in the visible and NIR regions. The optical band gap value was found to decrease with Al content from 3.22 eV to 3.18 eV. The results are discussed in correlation with structural characteristics and Al content in the films.     

Structural properties of low-temperature grown ZnO thin films determined by X-ray diffraction and X-ray absorption spectroscopy

The epitaxial growth of ZnO thin films on Al₂O₃ (0001) substrates have been achieved at a low-substrate temperature of 150 °C using a dc reactive sputtering technique. The structures and crystallographic orientations of ZnO films varying thicknesses on sapphire (0001) were investigated using X-ray diffraction (XRD). We used angle-dependent X-ray absorption near-edge structure (XANES) and extended X-ray absorption fine structure (EXAFS) spectroscopy to examine the variation of local structure. The XRD data showed that the crystallinity of the film is improved as the film thickness increases and the strain is fully released as the film thickness reached about 800 Å. The Zn K-edge XANES spectra of the ZnO films have a strong angle-dependent spectral feature resulting from the preferred c-axis orientation. The wurtzite structure of the ZnO films was explicitly shown by the XRD and EXAFS analysis. The carrier concentration, Hall mobility and resistivity of the 800 Å-thick ZnO film were 1.84 × 10¹⁹ cm^− 3, 24.62 cm²V^− 1s^− 1, and 1.38 × 10^− 2 Ω cm, respectively.     

Microstructure of a-plane ZnO grown on LaAlO3 (001)

The microstructure of a-plane ZnO grown on LaAlO₃ (LAO) (001) has been systematically investigated by employing X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Based on the results of XRD and TEM, only a-plane ZnO has been found to grow on LAO (001), and it consists of two types of domains perpendicular to each other. The crystal orientation relationships of a-plane ZnO domains with LAO have been verified to be [0001]_ZnO//[110]_LAO and [11?00]_ZnO//[11?0]_LAO. The domain boundaries in the a-plane ZnO are along the direction in a rotation angle of about 45° from the c-axes of ZnO. The surface morphology of ZnO films in SEM exhibits domain structure in stripe-like shape. The formation of two domains can be attributed to the cubic symmetry of the surface configuration of LAO (001).     

Influence of VI/II ratios on the growth of ZnO thin films on sapphire substrates by low temperature MOCVD

We investigated the structural, electrical, and optical properties of ZnO thin films grown at different VI/II ratios on sapphire substrates by metalorganic chemical vapor deposition. Transmission electron microscopy and X-ray diffraction revealed the epitaxial nature with a reduced dislocation density of the ZnO films grown at increased VI/II ratios. The carrier concentration of the films increased to 4.9 × 10¹⁸ cm^− 3 and their resistivity decreased to 1.4 × 10^− 1 Ω cm at a VI/II ratio of 513.4 μmol/min. The ZnO films also showed good optical transmittance (> 80%) in the visible and near-infrared wavelength regions. The room temperature PL revealed a strong band-edge emission with a weak deep level emission, suggesting the good crystalline quality of the ZnO films on the sapphire substrates. Furthermore, the intensity ratio of the band-edge emission to the deep-level emission (I_UV/I_Vis) increased with increasing VI/II ratio.     

Structural, optical and magnetic properties of Zn1 − xMnxO micro-rod arrays synthesized by spray pyrolysis method

Undoped and Mn-doped ZnO micro-rod arrays were fabricated by the spray pyrolysis method on glass substrates. X-ray diffraction and scanning electron microscopy showed that these micro-rod arrays had a polycrystalline wurtzite structure and high c-axis preferred orientation. Photoluminescence studies at 10 K show that the increase of manganese content leads to a relative decrease in deep level band intensity with respect to undoped ZnO. Magnetic measurements indicated that undoped ZnO was diamagnetic in nature whereas Mn-doped ZnO samples exhibited ferromagnetic behavior at room temperature, which is possibly related to the substitution of Mn ions (Mn^2 +) for Zn ions in the ZnO lattice.     

MgxZn1−xO (x = 0-1) films fabricated by sol-gel spin coating

Mg_xZn_1−xO films were deposited onto the glass substrate by a sol-gel spin coating method. The drying and annealing temperatures were 300 and 500 °C in air. As x varies from 0 to 1, it was observed that the crystal structure is changed from wurtzite ZnO to cubic MgO. The morphology characterizations of these films were observed by scanning electron microscope. The randomly oriented hexagonal nanorods were gown on the glass surface when x = 0 and 0.25, which became disappeared with increasing Mg contents. The optical properties of these films were investigated by room-temperature photoluminescence (PL) and UV-vis absorption spectra, which show that the optical band gap and photoluminescence in the visible and UV regions can be ideally tuned by varying the Mg contents in the Mg_xZn_1−xO alloy films.     

Synthesis of c-axis preferred orientation ZnO:Al transparent conductive thin films using a novel solvent method

Transparent aluminum doped zinc oxide (ZnO:Al, AZO) conducting thin films with a high-preferential c-axis orientation were synthesized using a new sol-gel formula. The films were deposited using a spin-coating route onto borosilicate glass substrates. We used propylene glycol methyl ether (PGME) as the solvent in place of ethylene glycol monomethyl ether (EGME), which is commonly used because it is easier to deposit onto the substrates. PGME is also superior in terms of health and safety. PGME solvent does not need to settle for several days before use and can be spin-coated as soon as the raw material and solvent are mixed. The effects of this novel solvent on the structural, morphological, electrical and optical properties are discussed using XRD, SEM, a four-point probe and UV-VIS spectrophotometry. It was found that the films produced with PGME showed a high-preferential c-axis orientation and compact microstructure in comparison films produced using EGME. The electrical resistivity of AZO thin films produced with PGME solvent was lowered to 3.474 × 10^− 3Ω cm after annealing in 95 N₂/5H₂ atmosphere. In addition, the optical transmittances of AZO thin films on glass plates were higher than 90% in the visible wavelength region.     

Preparation and conductive properties of neodymium-doped lanthanum nickelate thin films by chemical solution deposition method

Neodymium-doped lanthanum nickelate (La_1 − xNd_xNiO₃, LNNO) thin films have been prepared on Si substrates by chemical solution deposition method. The effects of annealing temperature and the neodymium concentration on the structural and electrical properties of the thin films have been investigated. X-ray diffraction analysis showed that the LNNO thin films exhibited perovskite structure with (100) preferential orientation. The (100) orientation degree of the thin films changed with neodymium content; however, the resistivity of the thin films was not related to the degree of orientation. Field emission scanning electron microscopy observations confirmed that the films had a smooth surface and uniform thickness. The resistivity of the thin films annealed at 700 °C increased from 1.97 mΩ·cm to 5.35 mΩ·cm, with increasing neodymium doping amount from LaNiO₃ to La_0.6Nd_0.4NiO₃.     

Effect of thermal treatments on the structure of MoNxOy thin films

MoN_xO_y films were deposited on steel substrates by dc reactive magnetron sputtering. The depositions were carried out from a pure molybdenum target, varying the flow rate of reactive gases. X-ray diffraction (XRD) results revealed the occurrence of cubic MoN_x and hexagonal (δ-MoN) phases for the films with high nitrogen flow rates. The increase of oxygen content induces the decrease of the grain size of the molybdenum nitride crystallites. The thermal stability of a set of samples was studied in vacuum, for an annealing time of 1 h, for temperatures ranging from 500 to 800 °C in 100 °C steps. The results showed that pure molybdenum nitride films changed their structure from a meta-stable cubic MoN to hexagonal δ-MoN and cubic γ-Mo₂N-type structures with increasing annealing temperatures. The samples with molybdenum nitride films evidenced a good thermal stability, but those with molybdenum oxynitride coatings showed a tendency to detach with the increase of the annealing temperature.     

Influence of doping concentration on the properties of ZnO:Mn thin films by sol-gel method

Thin films of Mn-doped ZnO with different doping concentration (0.8, 1, 3, 5 at%) were prepared on Pt/Ti/SiO₂/Si substrates by using sol-gel method. The effects of the doping concentration on the structural properties, electrical characteristics and element binding energy in films were investigated. X-ray diffraction (XRD) results showed that the c-axis orientation of ZnO films was affected by Mn²⁺ content. Current-voltage (I-V) measurements indicated that resistivities of ZnO films were observably enhanced by dopant of Mn²⁺ and the resistivities value increased with a doping level up to 5 at% Mn. X-ray photoelectron spectroscopy (XPS) patterns suggested that the binding energies of O1s and ZnL₃M₄₅M₄₅ were affected by the content of Mn²⁺.     

Electrical properties of lead-free thick film NTC thermistors based on perovskite-type BaCoxCo2xBi1 − 3xO3

Lead-free thick film negative temperature coefficient (NTC) thermistors based on perovskite-type BaCo^II_xCo^III_2xBi_1 − 3xO₃ (x ≤ 0.1) were prepared by mature screen-printing technology. The microstructures of the thick films sintered at 720 °C were examined by X-ray diffraction and scanning electron microscopy. The electrical properties were analyzed by measuring the resistance-temperature characteristics. For the BaBiO₃ thick films, the room-temperature resistivity is 0.22 MΩ cm, while the room-temperature resistivity is sharply decreased to about 3 Ω cm by replacing of Bi with a small amount of Co. For compositions 0.02 ≤ x ≤ 0.1, the values of room-temperature resistivity (ρ₂₃), thermistor constant (B_25/85) and activation energy are in the range of 1.995-2.975 Ω cm, 1140-1234 K and 0.102-0.111 eV, respectively.     

Synthesis and characterization of beta barium borate thin films obtained from the BaO-B2O3-TiO2 ternary system

This work reports on the synthesis and the structural and optical characterization of beta barium borate (β-BBO) thin films containing 4, 8 and 16 mol% of titanium oxide (TiO₂) deposited on fused silica and silicon (0 0 1) substrates using the polymeric precursor method. The thin films were characterized by X-ray diffraction, Raman spectroscopy, atomic force microscopy and scanning electron microscopy techniques. The optical transmission spectra of the thin films were measured over a wavelength range of 800-200 nm. A decrease was observed in the band gap energy as the TiO₂ content was raised to 16 mol%. Only the β-BBO phase with a preferential orientation in the (0 0 l) direction was obtained in the sample containing 4 mol% of TiO₂ and crystallized at 650 °C for 2 h.