Experimental study of the performances of a modified diesel engine operating in homogeneous charge compression ignition (HCCI) combustion mode versus the original diesel combustion mode

Homogeneous charge compression ignition (HCCI) combustion mode provides very low NO_x and soot emissions; however, it has some challenges associated with hydrocarbon (HC) emissions, fuel consumption, difficult control of start of ignition and bad behaviour to high loads. Cooled exhaust gas recirculation (EGR) is a common way to control in-cylinder NO_x production in diesel and HCCI combustion mode. However EGR has different effects on combustion and emissions, which are difficult to distinguish. This work is intended to characterize an engine that has been modified from the base diesel engine (FL1 906 DEUTZ-DITER) to work in HCCI combustion mode. It shows the experimental results for the modified diesel engine in HCCI combustion mode fueled with commercial diesel fuel compared to the diesel engine mode. An experimental installation, in conjunction with systematic tests to determine the optimum crank angle of fuel injection, has been used to measure the evolution of the cylinder pressure and to get an estimate of the heat release rate from a single-zone numerical model. From these the angle of start of combustion has been obtained. The performances and emissions of HC, CO and the huge reduction of NO_x and smoke emissions of the engine are presented. These results have allowed a deeper analysis of the effects of external EGR on the HCCI operation mode, on some engine design parameters and also on NO_x emission reduction.     

Combining GTL fuel,reformed EGR and HC-SCR aftertreatment system to reduce diesel NOx emissions. A statistical approach

An ultra-low sulphur diesel (ULSD) fuel and a synthetic gas-to-liquid (GTL) fuel, besides different types of standard and reformed EGR, were evaluated in a single-cylinder, direct injection, diesel engine equipped with hydrocarbon-selective catalytic reduction (HC-SCR) aftertreatment system. The results obtained were statistically analysed (at 95% statistical significance) to identify the most significant factors that affect NO_x emissions and to search for the optimum operation conditions in order to minimize these emissions. For that purpose, a fully crossed factorial experimental design was used, including two different engine speeds (1200 and 1500 rpm), two engine loads (25% and 50%), and four EGR/REGR ratios (0%, 10%, 20% and 30%) resulting in almost one hundred tests. An optimal combination of fuel type, REGR type and REGR ratio was proved to reduce around 89–95% of the reference NO_x emissions. In general, at 25% engine load GTL fuelling combined with the reformed EGR with the highest hydrogen content was found the most desirable, as the hydrogen sharply increased the NO_x conversion in the SCR catalyst. Differently, at 50% load standard EGR was sufficient to reach high NO_x reductions. These findings may be used for the implementation of a system on-board capable to switch from EGR to REGR, which will help engine manufacturers to meet the future emission regulations.     

H2 effects on diesel combustion and emissions with an LPL-EGR system

In this study, we examined H₂ effects on the combustion and emissions of a diesel engine with low-pressure loop (LPL) exhaust gas recirculation (EGR). We converted a 2.2-L four-cylinder direct-injection diesel engine satisfying Euro5 for H₂ supply. An LPL-EGR system replaced the high-pressure loop (HPL) EGR system. For all tests, the brake mean effective pressure (BMEP) was kept at 4 bar and the EGR ratio was varied from 9 to 42%. The H₂ energy percentage was varied from 0 to 7.4% independently to evaluate the H₂ effects and EGR effects separately. The heat release rate was calculated from the measured cylinder pressure. We found that substitution of H₂ for diesel fuel made the premixed burn fraction larger, and reduced the nitrous oxide (NOx) and particulate matter (PM) emissions simultaneously. For example, the NOx emissions were reduced by 36% for an EGR of 42% and an H₂ percentage of 7.4%. PM emissions were reduced by 18% for an EGR of 35% and an H₂ percentage of 7.4% compared with diesel fuel only cases.     

Remarkable improvement of NOx–PM trade-off in a diesel engine by means of bioethanol and EGR

In order to realize a premixed compression ignition (PCI) engine, the effects of bioethanol–gas oil blends and exhaust gas recirculation (EGR) on PM–NO_x trade-off have been investigated focusing on ignition delay, premixed combustion, diffusion combustion, smoke, NO_x and thermal efficiency. The present experiment was done by increasing the ethanol blend ratio and ethanol and by increasing the EGR ratio in a single cylinder direct injection diesel engine. It is found that a remarkable improvement in PM–NO_x trade-off can be achieved by promoting the premixing based on the ethanol blend fuel having low evaporation temperature, large latent heat and low cetane number as well, in addition, based on a marked elongation of ignition delay due to the low cetane number fuel and the low oxygen intake charge. As a result, very low levels of NO_x and PM, which satisfies the 2009 emission standards imposed on heavy duty diesel engines in Japan, were achieved without deterioration of brake thermal efficiency in the PCI engine fuelled with the 50% ethanol blend diesel fuel and the high EGR ratio. It is noticed that smoke can be reduced even by increasing the EGR ratio under the highly premixed condition.     

Engine performance and emissions of a diesel engine operating on diesel-RME (rapeseed methyl ester) blends with EGR (exhaust gas recirculation)

The effects of biodiesel (rapeseed methyl ester, RME) and different diesel/RME blends on the diesel engine NO_x emissions, smoke, fuel consumption, engine efficiency, cylinder pressure and net heat release rate are analysed and presented. The combustion of RME as pure fuel or blended with diesel in an unmodified engine results in advanced combustion, reduced ignition delay and increased heat release rate in the initial uncontrolled premixed combustion phase. The increased in-cylinder pressure and temperature lead to increased NO_x emissions while the more advanced combustion assists in the reduction of smoke compared to pure diesel combustion. The lower calorific value of RME results in increased fuel consumption but the engine thermal efficiency is not affected significantly. When similar percentages (% by volume) of exhaust gas recirculation (EGR) are used in the cases of diesel and RME, NO_x emissions are reduced to similar values, but the smoke emissions are significantly lower in the case of RME. The retardation of the injection timing in the case of pure RME and 50/50 (by volume) blend with diesel results in further reduction of NO_x at a cost of small increases of smoke and fuel consumption.     

Homogeneous Charge Compression Ignition (HCCI) combustion: Implementation and effects on pollutants in direct injection diesel engines

Homogeneous Charge Compression Ignition (HCCI) combustion is a combustion concept which offers simultaneous reductions in both NO_x and soot emissions from internal combustion engines. In light of increasingly stringent diesel emissions limits, research efforts have been invested into HCCI combustion as an alternative to conventional diesel combustion. This paper reviews the implementation of HCCI combustion in direct injection diesel engines using early, multiple and late injection strategies. Governing factors in HCCI operations such as injector characteristics, injection pressure, piston bowl geometry, compression ratio, intake charge temperature, exhaust gas recirculation (EGR) and supercharging or turbocharging are discussed in this review. The effects of design and operating parameters on HCCI diesel emissions, particularly NO_x and soot, are also investigated. For each of these parameters, the theories are discussed in conjunction with comparative evaluation of studies reported in the specialised literature.     

Generating efficiency and emissions of a spark-ignition gas engine generator fuelled with biogas–hydrogen blends

We investigated the generating efficiency and pollutant emissions of a four-stroke spark-ignition gas engine generator operating on biogas–hydrogen blends of varying excess air ratios and hydrogen concentrations. Experiments were carried out at a constant engine speed of 1200 rpm and a constant electric power output of 10 kW. The experimental results showed that the peak values of generating efficiency, maximum cylinder pressure, and NO_x emissions were elevated at an excess air ratio of around 1.2 as the hydrogen concentration was increased. CO₂ emissions decreased as the excess air ratio and hydrogen concentration increased, due to lean-burn conditions and hydrogen combustion. An efficiency per NO_x emissions ratio (EPN) was defined to consider the relationship between the generating efficiency and NO_x emissions. A maximum EPN value of 0.7502 was obtained with a hydrogen concentration of 15%, for an excess air ratio of 2.0. At this EPN value, the NO_x and CO₂ emissions were 39 ppm and 1678.32 g/kWh, respectively, and the generating efficiency was 29.26%. These results demonstrated that the addition of hydrogen to biogas enabled the effective generation of electricity using a gas engine generator through lean-burn combustion.     

Hydrogen assisted diesel combustion

Hydrogen assisted diesel combustion was investigated on a DDC/VM Motori 2.5L, 4-cylinder, turbocharged, common rail, direct injection light-duty diesel engine, with a focus on exhaust emissions. Hydrogen was substituted for diesel fuel on an energy basis of 0%, 2.5%, 5%, 7.5%, 10% and 15% by aspiration of hydrogen into the engine's intake air. Four speed and load conditions were investigated (1800 rpm at 25% and 75% of maximum output and 3600 rpm at 25% and 75% of maximum output). A significant retarding of injection timing by the engine's electronic control unit (ECU) was observed during the increased aspiration of hydrogen. The retarding of injection timing resulted in significant NO_X emission reductions, however, the same emission reductions were achieved without aspirated hydrogen by manually retarding the injection timing. Subsequently, hydrogen assisted diesel combustion was examined, with the pilot and main injection timings locked, to study the effects caused directly by hydrogen addition. Hydrogen assisted diesel combustion resulted in a modest increase of NO_X emissions and a shift in NO/NO₂ ratio in which NO emissions decreased and NO₂ emissions increased, with NO₂ becoming the dominant NO_X component in some combustion modes. Computational fluid dynamics analysis (CFD) of the hydrogen assisted diesel combustion process captured this trend and reproduced the experimentally observed trends of hydrogen's effect on the composition of NO_X for some operating conditions. A model that explicitly accounts for turbulence–chemistry interactions using a transported probability density function (PDF) method was better able to reproduce the experimental trends, compared to a model that ignores the influence of turbulent fluctuations on mean chemical production rates, although the importance of the fluctuations is not as strong as has been reported in some other recent modeling studies. The CFD results confirm that temperature changes alone are not sufficient to explain the observed reduction in NO and increase in NO₂ with increasing H₂. The CFD results are consistent with the hypothesis that in-cylinder HO₂ levels increase with increasing hydrogen, and that the increase in HO₂ enhances the conversion of NO to NO₂. Increased aspiration of hydrogen resulted in PM, and HC emissions which were combustion mode dependent. Predominantly, CO and CO₂ decreased with the increase of hydrogen. The aspiration of hydrogen into the engine modestly decreased fuel economy due to reduced volumetric efficiency from the displacement of air in the cylinder by hydrogen.     

Experimental study of various effects of exhaust gas recirculation (EGR) on combustion and emissions of an automotive direct injection diesel engine

Cooled exhaust gas recirculation (EGR) is a common way to control in-cylinder NO_x production and is used on most modern high-speed direct injection (HSDI) diesel engines. However EGR has different effects on combustion and emissions production that are difficult to distinguish (increase of intake temperature, delay of rate of heat release (ROHR), decrease of peak heat release, decrease in O₂ concentration (and thus of global air/fuel ratio (AFR)) and flame temperature, increase of lift-off length, etc.), and thus the influence of EGR on NO_x and particulate matter (PM) emissions is not perfectly understood, especially under high EGR rates. An experimental study has been conducted on a 2.0 l HSDI automotive diesel engine under low-load and part load conditions in order to distinguish and quantify some effects of EGR on combustion and NO_x/PM emissions. The increase of inlet temperature with EGR has contrary effects on combustion and emissions, thus sometimes giving opposite tendencies as traditionally observed, as, for example, the reduction of NO_x emissions with increased inlet temperature. For a purely diffusion combustion the ROHR is unchanged when the AFR is maintained when changing in-cylinder ambient gas properties (temperature or EGR rate). At low-load conditions, use of high EGR rates at constant boost pressure is a way to drastically reduce NO_x and PM emissions but with an increase of brake-specific fuel consumption (BSFC) and other emissions (CO and hydrocarbon), whereas EGR at constant AFR may drastically reduce NO_x emissions without important penalty on BSFC and soot emissions but is limited by the turbocharging system.     

An experimental investigation on performance and emissions study with port injection using diesel as an ignition source for different EGR flow rates

Exhaust gas recirculation, EGR, is one of the most effective means of reducing NO_x emissions from IC engines and is widely used in order to meet the emission standards. In the present work, experimental investigation has been carried out to study the NO_x reduction characteristics by exhaust gas recirculation in a dual fueled engine using hydrogen and diesel. A single cylinder diesel engine was converted to operate on hydrogen-diesel dual fuel mode. Hydrogen was injected in intake port and diesel was injected directly inside the cylinder. The injection timing and injection duration of hydrogen were optimized initially based on the performance and emissions. It was observed that start of injection at 5° before gas exchange top dead center (BGTDC) and injection duration of 30° crank angle gives the best results. The flow rate of hydrogen was optimized as 7.5 lpm for the best start of injection and injection duration of hydrogen. Cold exhaust gas recirculation technique was adopted for the optimized injection parameter of hydrogen and flow rate. Maximum quantity of exhaust gases recycled during the test was 25% beyond this the combustion was not stable resulting in increase in smoke.     

Experimental investigation of the combustion characteristics,emissions and performance of hydrogen port fuel injection in a diesel engine

Diesel engines are indispensable in daily life. However, the limited supply of petroleum fuels and the stringent regulations on such fuels are forcing researchers to study the use of hydrogen as a fuel. In this study, a diesel engine is operated using hydrogen–diesel dual fuel, where hydrogen is introduced into the intake manifold using an LPG-CNG injector and pilot diesel is injected using diesel injectors. The energy contents of the total fuel, 0%, 16%, 36% and 46% hydrogen (the 0% hydrogen energy fraction represents neat diesel fuel), were tested at 1300 rpm of constant engine speed and 5.1 kW of constant indicated power. According to test results, the indicated thermal efficiency of the engine decreases and the isfc increases with an increasing hydrogen energy fraction. Additionally, indicated specific CO, CO₂ and smoke emissions decrease with an increasing percentage of hydrogen fuel. However, indicated specific NO_x emissions do not change at the 16% hydrogen energy fraction, in other words, with an increase in the hydrogen amount (36% and 46% hydrogen energy fraction of total fuel), a dramatic increase (58.8% and 159.7%, respectively) is observed. Additionally, the peak in-cylinder pressure and the peak heat release rate values increase with the increasing hydrogen rate.     

Effect of induction on exhaust gas recirculation and hydrogen gas in compression ignition engine with simarouba oil in dual fuel mode

Biofuels extracted from non-edible oil is sustainable and can be used as an alternative fuel for internal combustion engines. This study presents the performance, emission and combustion characteristic analysis by using simarouba oil (obtained from Simarouba seed) as an alternative fuel along with hydrogen and exhaust gas recirculation (EGR) in a compression ignition (CI) engine operating on dual fuel mode. Simarouba biofuel blend (B20) was prepared on volumetric basis by mixing simarouba oil and diesel in the proportion of 20% and 80% (v/v), respectively. Hydrogen gas was introduced at the flow rate of 2.67 kg/min, and EGR concentration was maintained at 30% of total air introduction. Performance, combustion and emission characteristics analysis were examined with biodiesel (B20), biodiesel with hydrogen substitution and biodiesel, hydrogen with EGR and were compared with neat diesel operation. Results indicate that BTE of the engine operating with biodiesel B20 was decreased when compared to neat diesel operation. However, introducing hydrogen along with B20 blend into the combustion chamber shows a slight increase in the BTE by 1%. NO_x emission was increased to 18.13% with the introduction of hydrogen than that of base fuel (diesel) operation. With the introduction of EGR, there is a significant reduction in NO_x emission due to decrease in in-cylinder temperature by 19.07%. A significant reduction in CO, CO_2, and smoke emissions were also noted with the introduction of both hydrogen and EGR. The ignition delay and combustion duration were increased with the introduction of hydrogen, EGR with biodiesel than neat diesel operation. Hence, the proposed biodiesel B20 with H₂ and EGR combination can be applied as an alternative fuel in CI engines.     

Influence of biodiesel on engine combustion and emission characteristics

This paper discusses the influence of biodiesel on the engine combustion characteristics. The considered fuel is neat biodiesel from rapeseed oil. The considered engine is a bus diesel engine with injection M system. The engine characteristics are obtained by experiments and numerical simulation. The results obtained with biodiesel are compared to those obtained with mineral diesel under various operating regimes. In this way, the influences of biodiesel usage on the injection pressure, injection timing, ignition delay, in-cylinder gas pressure and temperature, heat release rate, exhaust gas temperatures, harmful emissions, specific fuel consumption, and on engine power are analyzed. Furthermore, the relationships among fuel properties, injection and combustion characteristics, harmful emissions, and other engine performance are determined. Special attention is given to possible explanations of higher NO_x emission in spite of lower in-cylinder gas temperature.     

An experimental investigation on engine performance and emissions of a single cylinder diesel engine using hydrogen as inducted fuel and diesel as injected fuel with exhaust gas recirculation

Fast depletion of fossil fuels is demanding an urgent need to carry out research work to find out the viable alternative fuels for meeting sustainable energy demand with minimum environmental impact. In the future, our energy systems will need to be renewable and sustainable, efficient and cost-effective, convenient and safe. The technology for producing hydrogen from a variety of resources, including renewable, is evolving and that will make hydrogen energy system as cost-effective. Hydrogen safety concerns are not the cause for fear but they simply are different than those we are accustomed to with gasoline, diesel and other fossil fuels. For the time being full substitution of diesel with hydrogen is not convenient but use of hydrogen in a diesel engine in dual fuel mode is possible. So Hydrogen has been proposed as the perfect fuel for this future energy system. The experiment is conducted using diesel–hydrogen blend. A timed manifold induction system which is electronically controlled has been developed to deliver hydrogen on to the intake manifold. The solenoid valve is activated by the new technique of taking signal from the rocker arm of the engine instead of cam actuation mechanism. In the present investigation hydrogen-enriched air has been used in a diesel engine with hydrogen flow rate at 0.15 kg/h. As diesel is substituted and hydrogen is inducted, the NO_x emission is increased. In order to reduce NO_x emission an EGR system has been developed. In the EGR system a lightweight EGR cooler has been used instead of bulky heat exchanger. In this experiment performance parameters such as brake thermal efficiency, volumetric efficiency, BSEC are determined and emissions such as oxides of nitrogen, carbon dioxide, carbon monoxide, hydrocarbon, smoke and exhaust gas temperature are measured. Dual fuel operation with hydrogen induction coupled with exhaust gas recirculation results in lowered emission level and improved performance level compared to the case of neat diesel operation.     

Analysis of reformed EGR on the performance of a diesel particulate filter

The use of a diesel particulate filter (DPF) in combination with an upstream diesel oxidation catalyst (DOC) has been successfully implemented and shown to reduce carbon monoxide (CO), hydrocarbon (HC) and Particulate Matter (PM) diesel exhaust gas emissions. However issues including cost, size and uncontrolled active regeneration under a low temperature window still require attention. This study therefore primarily focuses on the potential benefits of using a single catalytic coated DPF (cDPF) and a combined DOC-cDPF instead of the DOC-DPF aftertreatment system utilising a passive, low temperature regeneration method. Comparisons were made through monitoring exhaust gas compositions from an experimental single cylinder diesel engine as well as measuring the pressure drop across the filters to analyse the accumulation of soot particles. The influence of reformed EGR (REGR), enriched simulated hydrogen (H₂) and CO, on DPF and cDPF soot loading was of interest as H₂ promotes the NO to NO₂ oxidation. Similarly the addition of simulated reformate (added either directly into the engine intake or exhaust manifold) for optimal performance of the aftertreatment systems was examined.The effects of adding REGR resulted in a significant decrease in total engine-out NO_x emissions, as well as an increase in both NO₂ concentration and NO₂/NO_x ratio. This resulted in improved filter efficiency and overall loading, especially under a DOC-cDPF aftertreatment configuration system. As a whole, a simultaneous NO_x and PM reduction was achieved.     

An experimental investigation of NO2 emission characteristics of a heavy-duty H2-diesel dual fuel engine

This paper investigated the nitrogen dioxide (NO₂) emissions of a heavy-duty diesel engine operated in hydrogen (H₂)-diesel dual fuel combustion mode with H₂ supplemented into the intake air. Preliminary measurements using the 13-mode European Stationary Cycle (ESC) demonstrated the significant effect of H₂ addition on the emissions of NO₂. The detailed effects of H₂ addition and engine load on NO₂ emissions were examined at 1200 RPM. The addition of a small amount of H₂ increased substantially the emissions of NO₂ and the NO₂/NO_x ratio, especially at low load. Increasing the engine load was found to inhibit the enhancing effect of H₂ on the conversion of NO to NO₂ with the maximum NO₂/NO_x ratio observed at lower H₂ concentration. The maximum NO₂ emissions of the H₂-diesel dual fuel operation were three (at 70% load) to five (at 10% load) times that of diesel operation. Further increasing the addition of H₂ beyond the point with maximum NO₂ emissions still produced more NO₂ than for diesel-only operation. Based on the experimental data obtained, the engine load and maximum averaged bulk mixture temperature were not the main factors dominating the formation of NO₂ in the H₂-diesel dual fuel engine. A preliminary analysis demonstrated the significant effect of the unburned H₂ on NO₂ emissions. When mixed with the hot combustion product, the unburned H₂ that survived the main combustion process might further oxidize to raise the HO₂ levels and enhance the conversion of NO to NO₂. In comparison, the changes in the combustion process including the start of combustion, combustion duration and maximum heat release rate may not contribute substantially to the increased NO₂ emissions observed.     

Effect of exhaust gas recirculation (EGR) temperature for various EGR rates on heavy duty DI diesel engine performance and emissions

DI diesel engines are well established today as the main powertrain solution for trucks and other relevant heavy duty vehicles. At the same time emission legislation (mainly for NO_x and particulate matter) becomes stricter, reducing their limit to extremely low values. One efficient method to control NO_x in order to achieve future emissions limits is the use of rather high exhaust gas recirculation (EGR) rates accompanied by increased boost pressure to avoid the negative impact on soot emissions. The method is based on the reduction of gas temperature level and O₂ availability inside the combustion chamber, but unfortunately it has usually an adverse effect on soot emissions and brake specific fuel consumption (bsfc). The use of high EGR rates creates the need for EGR gas cooling in order to minimize its negative impact on soot emissions especially at high engine load were the EGR flow rate and exhaust temperature are high. For this reason in the present paper it is examined, using a multi-zone combustion model, the effect of cooled EGR gas temperature level for various EGR percentages on performance and emissions of a turbocharged DI heavy duty diesel engine operating at full load. Results reveal that the decrease of EGR gas temperature has a positive effect on bsfc, soot (lower values) while it has only a small positive effect on NO. As revealed, the effect of low EGR temperature is stronger at high EGR rates.     

Generating efficiency and NOx emissions of a gas engine generator fueled with a biogas–hydrogen blend and using an exhaust gas recirculation system

This paper investigates the generating efficiency and NO_x emissions of a gas engine generator with a low-pressure loop exhaust gas recirculation system, fueled by a model biogas. Experiments for improving the generating efficiency and reducing NO_x emissions were conducted, utilizing optimum spark timings based on the maximum generating efficiencies with varying exhaust gas recirculation (EGR) rates. The test results show that both the NO_x emissions and the generating efficiency generally decrease when the EGR rate is increased. Also, by utilizing optimum spark timings with varying EGR rates, the addition of hydrogen to the biogas increases the generating efficiency of the engine. In particular, the generating efficiency of the biogas–hydrogen test increased by about 1.5% in comparison with the model biogas test for the optimum spark timing at 15% EGR. Accordingly, comprehensive techniques, such as the use of a biogas–hydrogen fuel mixture and optimum spark timings with respect to EGR rates, should be employed to efficiently generate electricity with a biogas engine.     

Comparative analysis of H2-diesel co-combustion in a single cylinder engine and a chassis dynamometer vehicle

Concerns as to the adverse effects of diesel engine exhaust on urban air quality have resulted in increasingly stringent emissions legislation, with the prospect of many major global cities potentially banning diesel vehicles. Emissions of nitrogen oxides (NO_x) and particulate matter (PM) are linked to increases in premature mortality, and the simultaneous control of both pollutants through modified combustion strategies presents a significant challenge. In this work, the effects of displacing diesel fuel with hydrogen on exhaust emissions were investigated in both a single cylinder research engine and in a demonstration vehicle. In the initial stage, tests were undertaken on a supercharged, direct injection, single cylinder diesel research engine at different engine loads, intake air pressures and EGR levels. Hydrogen was aspirated with the intake air, and EGR was simulated by supplying the intake pipe with compressed nitrogen gas. The results showed a reduction in CO₂ and particulate emissions with increasing H₂ addition, and an increase in NO_x emissions at H₂ levels greater than 10% of the total input energy to the engine. The next stage involved tests on a chassis dynamometer with a small van equipped with the multi-cylinder version of the single cylinder research engine. The van was fitted with a programmable H₂ augmentation system, with H₂ addition levels specified by accelerator pedal position. During full drive cycle tests conducted with and without H₂ augmentation up to 10%, an average rate of 1 kW of H₂ was supplied to the engine. With H₂ augmentation, over the total drive-cycle, reductions in CO, NO_x and particle number were observed, but a higher total PM mass was recorded.     

Methods for in-cylinder EGR stratification and its effects on combustion and emission characteristics in a diesel engine

The effects of in-cylinder EGR stratification on combustion and emission characteristics are investigated in a single cylinder direct injection diesel engine. To achieve in-cylinder EGR stratification, external EGR rates of two intake ports are varied by supplying EGR asymmetrically using a separated intake runner. The EGR stratification pattern is improved using a 2-step bowl piston and an offset chamfer at the tangential intake port. When high EGR gas is supplied to the left (tangential) port, a high EGR region is formed at the central upper region of the combustion chamber. Consequently, combustion is initiated in the low EGR region, and PM is reduced significantly. When high EGR gas is supplied to the right (helical) port, a high EGR region is formed at the lower periphery of the combustion chamber. Therefore, combustion is initiated in the high EGR region, and NO_x is reduced without PM penalty. Stratified EGR potentially reduces NO_x by maximum 45%, without penalties of performance and other emissions. A proper in-cylinder swirl with stratified EGR maximizes the effects and achieves simultaneous reduction of NO_x by 7% and PM by 23%. Moreover, the robustness of stratified EGR is evaluated under various operating conditions and injection strategies.