钛合金TC11车削中已加工表面质量试验研究

为了研究车削钛合金TC11时切削速度和刀具磨损对已加工表面质量的影响,选用涂层硬质合金刀片CNMG120408在不同切削条件下进行车削试验,分析后刀面磨损量随切削时间的变化规律;对比磨损刀具与新刀具切削的工件表面,观察表面粗糙度、表面形貌、显微硬度以及表层微观组织情况,分析切削速度和刀具磨损对已加工表面质量的影响规律。试验结果表明:在刀具磨损初期,即新刀具切削时,切削速度从60m/min增加到100m/min,刀具磨损程度增大,表面粗糙度值降低,硬化层深度减小,加工硬化程度略微增大,表面塑性变形层深度减小;在刀具磨损终期,不同切削速度下的表面粗糙度增大,表面形貌变差,硬化层深度和加工硬化程度增加,表面变形程度增大,塑性变形层深度增加。     

基于分形理论的玻璃切削力和表面粗糙度研究

基于分形理论研究了玻璃切削时不同切削参数对切削力及其分形维数以及表面粗糙度的影响。试验结果表明:切削力分形维数与玻璃切削过程的四个阶段密切相关,如玻璃切削过程以某一阶段(如大块破碎)为主,则切削力分形维数越小,表面粗糙度越大;如切削过程包含多个阶段,则切削力分形维数越大,表面粗糙度越大。     

Experimental Study on Cutting Forces and Surface Integrity in High-Speed Side Milling of Ti-6Al-4V Titanium Alloy

This article is concerned with the cutting forces and surface integrity in high-speed side milling of Ti-6Al-4V titanium alloy. The experiments were conducted with coated carbide cutting tools under dry cutting conditions. The effects of cutting parameters on the cutting forces, tool wear and surface integrity (including surface roughness, microhardness and microstructure beneath the machined surface) were investigated. The velocity effects are focused on in the present study. The experimental results show that the cutting forces in three directions increase with cutting speed, feed per tooth and depth of cut (DoC). The widths of flank wear VB increases rapidly with the increasing cutting speed. The surface roughness initially decreases and presents a minimum value at the cutting speed 200 m/min, and then increases with the cutting speed. The microstructure beneath the machined surfaces had minimal or no obvious plastic deformation under the present milling conditions. Work hardening leads to an increment in micro-hardness on the top surface. Furthermore, the hardness of machined surface decreases with the increase of cutting speed and feed per tooth due to thermal softening effects. The results indicated that the cutting speed 200 m/min could be considered as a critical value at which both relatively low cutting forces and improved surface quality can be obtained.     

Influence of cutting speed on surface integrity for powder metallurgy nickel-based superalloy FGH95

Powder metallurgy (PM) nickel-based superalloy FGH95 has been widely used for components, which requires the greatest service performance. The surface integrity is becoming more and more important in order to satisfy the increasing service demands. However, the machined surface of FGH95 is easily damaged due to its poor machinability. The purpose of this paper is to investigate the effects of dry milling process parameters on the surface integrity of FGH95. Experiments were conducted on a CNC machining center under different cutting speeds. The machined surface is evaluated in terms of surface roughness, microhardness and white layer. Experiments results show milled surface integrity of FGH95 is sensitivity to the cutting speeds. The machined surface roughness decreases with increase of the cutting speed, but with further increase of cutting speed between 80?m/min to 100?m/min an increase in surface roughness appears. For microhardness, it can be seen that the machined workpiece surface hardens seriously. It can also draw the conclusion that cutting speed has the marginal effect on the white layer thickness generated in the machined subsurface.     

不同冷却润滑条件下TB6钛合金高速切削表面完整性研究

通过TB6钛合金高速铣削试验,测量观察加工表面粗糙度、表面三维形貌和表层微观组织等表面完整性特征,利用极差法分析切削参数对表面粗糙度影响的显著性,探讨冷却润滑条件对加工表面形貌和表面变质层的影响。研究表明:工艺参数对表面粗糙度影响程度依次为径向切深、切削速度、进给量和轴向切深;相比低温冷风加,微油雾润滑加工时钛合金表面粗糙度低,且表面无明显晶粒变形,表明加工表面塑性变形是影响粗糙度的主要因素。     

基于声发射技术的微切削加工表面形貌监测

采用声发射技术对工件材料为A16061-T6的微切削表面轮廓进行了实时测量.采集监控微切削加工表面时产生的声发射均方根信号,并与表面轮廓仪测得的结果进行对比.研究表明,声发射均方根信号与微切削表面形貌很好的相对应,因此,声发射技术适于微切削表面形貌的监测.研究了切削用量(每齿进给量和主轴转速)与表面形貌之间的关系,微切削的每齿进给量对表面粗糙度影响较大.     

Effect of cutting speed on surface integrity and chip morphology in high-speed machining of PM nickel-based superalloy FGH95

High-speed machining is being recognized as one of the key manufacturing technologies for getting higher productivity and better surface integrity. FGH95 powder metallurgy superalloy is a kind of nickel-based superalloy which is produced by near-net-shape technology. With increasing demands for high precision and high performance of FGH95 components in aerospace industry, it is essential to recognize that the machined surface integrity may determine machined part service performance and reliability. Then, little is known about the machined surface integrity of this superalloy. Thus, the surface integrity in high-speed machining of FGH95 is investigated in this paper. Experiments are conducted on a CNC milling center with coated carbide tools under dry cutting conditions. The surface integrity is evaluated in terms of surface roughness, microhardness, and white layer. The influence of cutting speed on chip morphology is also investigated. Experiment results show that surface integrity and chip morphology of FGH95 are very sensitive to the cutting speed. When cutting speeds are below 2,400?m/min, the values of surface roughness have little variation, while when cutting speeds are in the range of 2,800–3,600?m/min, the values of surface roughness are higher than that of other cutting speeds. Severe work hardening is observed resulting from high-speed machining of FGH95 superalloy. The higher the cutting speed, the higher the surface hardness. When cutting speeds are in the range of 2,800–3,600?m/min, the white layer thickness is slightly higher than that of other cutting speeds. In high-speed machining of FGH95, the chip is segmented and has a typical sawtooth shape. The degree of serrated chip increases with the cutting speed. When the cutting speeds exceed 2,400?m/min, serrated chips change into fragment chips.     

高速铣削SiC_p/Al复合材料表面形貌功率谱密度研究

为了研究切削参数对高速铣削SiCp/Al复合材料表面微观形貌的影响,本文采用不同切削参数进行了高速铣削实验,利用Talyscan150型表面粗糙度测试仪对加工表面进行测量,对获得的表面数据进行功率谱密度(PSD)分析。结果表明:高速铣削SiC颗粒增强铝基复合材料时,进给量与铣削深度对功率谱密度影响不大,切削速度是主要影响因素,并且随着切削速度的增大,功率谱密度值降低,表面质量提高。加工表面的主要空间波长成分能够反映加工工艺条件对加工表面形貌的影响。     

EFFECT OF PROCESS PARAMETERS AND TOOL SHAPE ON THE MACHINABILITY OF A PARTICULATE FILLED-POLYMER COMPOSITE MATERIAL FOR RAPID TOOLING

This paper presents the results of an experimental study on the effects of machining parameters (cutting speed, feed, depth of cut) and tool shape on chip formation, surface topography, resultant cutting force and surface roughness produced in flat and ball end milling of the Ren Shape-Express 2000™ aluminum particulate filled-polymer composite material. This material is shown to exhibit a brittle-to-ductile transition in chip formation with decreasing cutting speed. The transition is explained by the strain-rate sensitivity of the polymer matrix and is found to correlate well with a corresponding change in the surface roughness. The absence of clear feed marks on the milled surface explains why molds made from the composite material require less hand polishing than machined metal molds. The influence of cutting conditions and tool shape (flat end vs. ball-nose) on the cutting force, surface roughness, and workpiece breakout are discussed and relevant comparisons with conventional metal and polymer machining are made.     

Surface topography and roughness of high-speed milled AlMn1Cu

The aluminum alloy AlMn1Cu has been broadly applied for functional parts production because of its good properties. But few researches about the machining mechanism and the surface roughness were reported. The high-speed milling experiments are carried out in order to improve the machining quality and reveal the machining mechanism. The typical topography features of machined surface are observed by scan electron microscope(SEM). The results show that the milled surface topography is mainly characterized by the plastic shearing deformation surface and material piling zone. The material flows plastically along the end cutting edge of the flat-end milling tool and meanwhile is extruded by the end cutting edge, resulting in that materials partly adhere to the machined surface and form the material piling zone. As the depth of cut and the feed per tooth increase, the plastic flow of materials is strengthened and the machined surface becomes rougher. However, as the cutting speed increases, the plastic flow of materials is weakened and the milled surface becomes smoother. The cutting parameters (e.g. cutting speed, feed per tooth and depth of cut) influencing the surface roughness are analyzed. It can be concluded that the roughness of the machined surface formed by the end cutting edge is less than that by the cylindrical cutting edge when a cylindrical flat-end mill tool is used for milling. The proposed research provides the typical topography features of machined surface of the anti-rust aluminum alloy AlMn1Cu in high speed milling.     

Influence of tool wear on surface roughness in hard turning using differently shaped ceramic tools

Hard turning has been applied in many cases in producing bearings, gears, cams, shafts, axels, and other mechanical components since the early 1980s. Mixed ceramics (aluminum oxide plus TiC or TiCN) is one of the two cutting tool materials (apart from PCBN) widely used for finish machining of hardened steel (HRC 50–65) parts, especially under dry machining conditions and moderate cutting speed ranging from 90 to 120 m/min. This paper reports an extensive characterization of the surface roughness generated during hard turning (HT) operations performed with conventional and wiper ceramic tools at variable feed rate and its changes originated from tool wear. Moreover, it compares some predominant tool wear patterns produced on the two types of ceramic inserts and their influence on the alteration of surface profiles. After the hard turning tests, the relevant changes of surface profiles and surface roughness parameters were successively registered and measured by a stylus profilometer. In this investigation, a set of 2D surface roughness parameters, as well as profile and surface characteristics, such as the amplitude distribution functions, bearing area curves and symmetrical curves of geometrical contact obtained for the machined surface, were determined and analyzed. A novel aspect of this research is that the notch wear progress at the secondary cutting (trailing) edges was found to produce the substantial modifications of the individual irregularities, and constitute the altered surface profiles. Moreover, this research contributes to practical aspects of HT technology due to exploring the relations between the tool state at different times within the tool life and the relevant surface roughness characterization.     

Empirical models and optimal cutting parameters for cutting forces and surface roughness in hard milling of AISI H13 steel

In the present research, an attempt has been made to experimentally investigate the effects of cutting parameters on cutting forces and surface roughness in hard milling of AISI H13 steel with coated carbide tools. Based on Taguchi’s method, four-factor (cutting speed, feed, radial depth of cut, and axial depth of cut) four-level orthogonal experiments were employed. Three cutting force components and roughness of machined surface were measured, and then range analysis and analysis of variance (ANOVA) are performed. It is found that the axial depth of cut and the feed are the two dominant factors affecting the cutting forces. The optimal cutting parameters for minimal cutting forces and surface roughness in the range of this experiment under these experimental conditions are searched. Two empirical models for cutting forces and surface roughness are established, and ANOVA indicates that a linear model best fits the variation of cutting forces while a quadratic model best describes the variation of surface roughness. Surface roughness under some cutting parameters is less than 0.25 μm, which shows that finish hard milling is an alternative to grinding process in die and mold industry.     

45调质钢切削表面粗糙度的试验研究

本文采用YT15硬质合金刀片对45调质钢的表面粗糙度进行了车削试验研究,探讨了主轴转速、切削深度、进给量对表面粗糙度的影响规律,总结出车削45调质钢的合理的切削参数。试验表明：当切削速度为200m／min左右、进给量为0．1mm／r、切深为0．3-0．5mm时,可进行高效高质的加工。     

Cutting tool condition monitoring by analyzing surface roughness,work piece vibration and volume of metal removed for AISI 1040 steel in boring

The vibration is one of the intensive problems in boring process. Machining and tool wear are affected more by vibration of tool due to length of boring bar. The present work is to estimate the effect of cutting parameters on work piece vibration, roughness on machined surface and volume of metal removed in boring of steel (AISI1040). A laser Doppler vibrometer (LDV) was used for online data acquisition and a high-speed FFT analyzer used to process the AOE signals for work piece vibration. A design of experiments was prepared with eight experiments with two levels of cutting parameters such as spindle rotational speed, feed rate and tool nose radius. Taguchi method has been used to optimize the cutting parameters and a multiple regression analysis is done to obtain the empirical relation of Tool life with roughness of machined surface, volume of metal removed and amplitude of work piece vibrations.     

Machining performance of a grooved tool in dry machining Ti-6Al-4 V

In this paper, dry machining experiment of Ti-6Al-4 V was carried out to investigate the machining performance of a grooved tool in terms of its wear mechanisms and the effects of cutting parameters (cutting speed, feed rate, and cutting depth) on tool life and surface roughness of the machined workpiece. The results showed that chip-groove configuration substantially improved the machining performance of cutting tool. The main wear mechanisms of the grooved tool were adhesive wear, stripping wear, crater wear, and dissolution-diffusion wear. The resistance to chipping was enhanced due to the decrease of contact pressure of tool-chip interface. And the resistance to plastic deformation of tool nose was weakened at the cutting speed of more than 60 m/min. The appropriate cutting speed and feed rate were less than 70 m/min and 0.10 mm/r, respectively. With cutting speed increasing, the surface roughness of machined workpiece decreased. A high feed rate helped the formation of higher surface roughness except 0.21 mm/r. When cutting depth increased, tool nose curvature and phase transformation of workpiece material had great impact on surface roughness.     

An experimental investigation on the machining characteristics of microscale end milling

This paper discusses an experimental approach to assess the machining characteristics in microscale end milling operation through a systematic experimentation procedure. Microchannels were machined on brass plates using a carbide end mill of 1?mm diameter to analyze the effect of chip load (feed per tooth) and cutting speed on the surface roughness, specific cutting pressure, and cutting forces during microend milling operation. The tangential and radial components of forces were analyzed with the help of a three-dimensional model using the force signals acquired through KISTLER dynamometer. Feed per tooth and the interaction of cutting speed and chip load were identified as the critical parameters affecting the surface roughness of microchannel. Applying the concept of elastic recovery on the side wall surface of microchannels, the minimum chip thickness during the above micromilling operation was evaluated as 0.97???m, and the result was validated by the drastic increase in specific cutting pressure and erratic behavior of cutting forces below a chip load of 1???m.     

Surface roughness analysis of hardened steel after high-speed milling

The work refers to analysis of various factors affecting surface roughness after end milling of hardened steel in high-speed milling (HSM) conditions. Investigations of milling parameters (cutting speed v(c) , axial depth of cut a(p) ) and the process dynamics that influence machined surface roughness were presented, and a surface roughness model, including cutter displacements, was elaborated. The work also involved analysis of surface profile charts from the point of view of vibrations and cutting force components. The research showed that theoretic surface roughness resulting from the kinematic-geometric projection of cutting edge in the workpiece is significantly different from the reality. The dominant factor in the research was not feed per tooth f(z) (according to the theoretical model) but dynamical phenomena and feed per revolution f.     

Micro-defects on machined carbon steel surfaces

Contrary to the evidence of stylus instruments, the residual roughness of machined 0.35% carbon steel surfaces changes as a function of cutting speed. The origin of the micro-defects, observed by electron microscopy, and with one exception, unresolved by conventional roughness measurement techniques, is thought not to be any malfunction of the machining process, but inherent in the process of surface formation. This paper describes micro-defects considered relevant to contacting surfaces and indicates that cutting speed selection for finish machining of tribological components based on conventional roughness measurements is questionable     

高速车削工件表面形貌及其粗糙度特征的试验研究

借助于扫描电镜照片、已加工样品表面形貌轮廓描绘和试验数据处理等手段,对高速车削工件已加工表面形貌与其表面粗糙度之间的关系以及它们的形成特征进行了分析研究.研究结果表明,切削速度和被切削材料的硬度是决定高速车削过程中被切削层材料变形和已加工表面形貌及其表面粗糙度形成的主要因素,随着被切削材料硬度和切削速度的提高,工件已加工表面质量在一定程度上得到了改善.在已加工表面上出现了犁垄和高速加工所特有的熔融金属涂抹现象,由此决定着已加工表面粗糙度值的变化.     

切削条件对氢化锂零件表面粗糙度的影响

通过车削试验研究了不同切削参数对氢化锂材料加工表面粗糙度的影响趋势及其成因。结果表明:表面粗糙度随切削速度和圆周进给量的增加呈增大趋势,随切削深度的增加呈减小趋势;进给量是影响表面粗糙度的主要因素。