Preparation and properties of core–shell silver/polyimide nanocomposites

A new series of core–shell structured silver/polyimide (PI) nanocomposites was prepared by in situ polymerization followed by the chemical imidization of poly(amic acid) (PAA, precursor of PI) at a low temperature. The TEM images showed that the silver cores of the nanocomposites were encapsulated with homogeneous shells with thickness of 4 and 8 nm at silver contents of 90 and 60 %, respectively. The shell thickness was controlled by varying the content of PAA. FTIR spectroscopic analysis indicated that the imide ring formation occurred after the chemical imidization. The Ag/PI nanocomposites showed excellent thermal stability and exhibited only 10 % weight loss at 300 °C in the air. Moreover, percolation was observed at silver weight fractions close to the critical value, and the maximum dielectric permittivity of the nanocomposites was 120, which is about 40 times higher than that of pristine PI.     

Synthesis and dynamic mechanical study of core–shell structure epoxy/polyacrylate composite particle

A material with high damping property and based on epoxy/polyacrylate (EP/PA) composite particles was synthesized by two-stage emulsion polymerization. Transmission electron microscopy (TEM) showed that the composite particles have a spherical morphology, a core–shell structure and a diameter of 100 nm–130 nm. Fourier transform infrared spectra (FTIR) indicated the cross-linking between EP groups in the core layer and carboxyl groups in the shell layer of the composite particles during film formation. The cross-linking reaction improved the dynamic mechanical property by the interaction of core and shell polymers. The effects of the cross-linking agent and ratio of the two polymers on the damping capacity were studied by dynamic mechanical analysis (DMA). DMA results revealed that a certain amount of acrylic acid could markedly enhance the loss factor (tan δ) and slightly widen the damping temperature range. When the EP/PA ratio was 1:7, peak values for tan δ of the composite materials could reach 2.10, exceeding the value for most damping materials. The result implies that the EP/PA composites have great potential application in damping steel surface coatings.     

Fabrication and properties of polysilsesquioxane-based trilayer core–shell structure latex coatings with fluorinated polyacrylate and silica nanocomposite as the shell layer

Polysilsesquioxanes (PSQ)-based core–shell fluorinated polyacrylate/silica hybrid latex coatings were synthesized with PSQ latex particles as the seeds, and methyl methacrylate, butyl acrylate, 3-(trimethoxysilyl) propyl methacrylate (MPS)-modified SiO₂ nanoparticles (NPs), 1H,1H,2H,2H-perfluorooctyl methacrylate (PFOMA) as the shell monomers by emulsifier-free miniemulsion polymerization. The results of Fourier transform IR spectroscopy, transmission electron microscopy, and dynamic light scattering suggested the obtained hybrid particles emerged with trilayer core–shell pattern. Contact angle analysis, x-ray photoelectron spectroscopy, and atom force microscopy results indicated that the hybrid film containing SiO₂ NPs showed higher hydrophobicity, lower surface free energy and water absorption, in comparison with the control system (without SiO₂ NPs). Compared with the control system, the hybrid latex film containing SiO₂ NPs in the fluorinated polyacrylate shell layer showed the higher content of fluorine atoms and a rougher morphology on the film surface. Additionally, thermogravimetric analysis demonstrated the enhanced thermostability of PSQ-based nanosilica composite fluorinated polyacrylate latex film.     

Silicon core–iron siloxane shell nanoparticle polymer composites with multiferroic properties

Multiferroic (MF) composites based on nanoparticles consisting of a silica core and a shell of spin-variable Fe(III) complexes in a polymer matrix (polystyrene) were synthesized and characterized by different methods. The nanoparticles had the formula 80SiO₂·20{Fe[OSi(Me)(OEt)₂]₃}, and their particle size was on the order of 5–7 nm. Dielectric and electron spin resonance studies showed the presence of two types of Fe ions in the nanocomposite. Iron ions in the low-spin state [Fe(III)-LS] and iron ions in the high-spin state [Fe(III)-HS], which were bound by indirect exchange interactions through oxygen and silicon atoms {[Fe(III)-LS]─O─Si─O─[Fe(III)-HS]} were responsible for the MF properties of the composites with core–shell nanoparticles. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47681.     

Preparation and characterization of silica sol/fluoroacrylate core–shell nanocomposite emulsion

The silica sol/fluoroacrylate core?Cshell nanocomposite emulsion was successfully synthesized via traditional emulsion polymerization through grafting of KH-570 onto silica particles. Comparing the performance of the polyacrylate copolymer, the fluorinated polyacrylate copolymer and the silica sol/fluoroacrylate core?Cshell nanocomposite emulsion, we can come to a conclusion that the silica sol/fluoroacrylate core?Cshell nanocomposite emulsion presents significantly excellent performance in all aspects. The products were characterized by Fourier transform infrared (FTIR), photon correlation spectroscopy (PCS), transmission electron microscopy (TEM), thermogravimetry (TGA), Contact angle and UV?Cvis analyses techniques. The chemical structure of polyacrylate copolymer, fluorinated polyacrylate copolymer and silica sol/fluoroacrylate nanocomposite were detected by FTIR. The size and stability of emulsion latex particles were determined by PCS technique. TEM analysis confirmed that the resultant latex particle has the core?Cshell structure, obviously. The water absorption and contact angle data also showed that the silica sol/fluoroacrylate nanocomposite film has good hydrophobic performance. TGA analysis indicated the weight loss of the silica sol/fluoroacrylate nanocomposite film begins at around 350?°C which testifies its good thermal stability. The UV?Cvis spectroscopy analysis showed that the silica sol/fluoroacrylate nanocomposite film possess UV?Cvis shielding effect when the added volume amount of KH570 modified silica sol is up to 5?mL. Therefore, the excellent properties of hydrophobicity, thermodynamics and resistance to ultraviolet provide the silica sol/fluoroacrylate nanocomposite film with potential applications in variety fields. In addition, the formation mechanism of core?Cshell structure silica sol/fluoroacrylate nanocomposite latex particles was speculated.     

Preparation of α-Fe2O3/Ag core/shell nanocomposites and SERS properties

用籽晶法,以甲醛为还原剂、3-氨丙基三乙氧基硅烷(APS)为改性剂,在Ag［(NH₃)₂］⁺溶液中制备α-Fe₂O₃/Ag核壳结构复合粉体。采用XRD、TEM和EDX对样品进行表征,系统研究了APS改性剂、醇水比等对复合纳米颗粒包覆效果及性能的影响;并用吡啶(Py)为探针,研究了α-Fe₂O₃/Ag核壳纳米颗粒作为拉曼衬底时的拉曼增强性能相似文献   

Core–shell BaMoO4@SiO2 nanospheres: Preparation,characterization, and optical properties

Core–shell BaMoO₄@SiO₂ nanospheres were prepared in reverse microemulsions and exhibited enhanced photoluminescence (PL) intensity as compared to that of the uncoated BaMoO₄. Characterization was performed using transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), energy-dispersive X-ray spectroscopy (EDX), and X-ray powder diffraction (XRD). It was found that the silica shell could increase the PL intensity, but the shell is not the thicker the better. The PL emission can be decomposed into three individual Gaussian components: two UV emissions at 308 nm and 369 nm and a visible emission at 448 nm. Such short emission wavelengths can be attributed to quantum size effect of the small BaMoO₄ cores (～16 nm).     

Polyaniline–Carbon Nanotube Composites: Preparation Methods,Properties, and Applications

Synthesis of polyaniline and hybrid carbon nanotube reinforced polyaniline nanocomposites by various methods has discussed in this review. Different routes used for functionalization of carbon nanotube have been reported. The electrical, mechanical, and thermal properties of polyaniline/carbon nanotube nanocomposites are also discussed. The dispersion of functionalized carbon nanotube, filler concentration, and their alignment in the interior of polyaniline matrix affect their morphology. Furthermore, article focussed upon the various morphologies of polyaniline and polyaniline/carbon nanotube nanocomposites obtained with different methods along with electrical conductivity. Possible applications of polyaniline/carbon nanotube nanocomposites in the areas of actuators, sensors, electromagnetic interference shielding have also discussed.     

Preparation and characterization of novel polyethylene/carbon nanotubes nanocomposites with core–shell structure

Preparation of novel polyethylene/carbon nanotubes (CNTs) nanocomposites with core–shell structure was presented. The method involved in situ ethylene polymerization in which nanotube surface was treated with Grignard Agent, followed by reacting with active transition metal compound, TiCl₄. The multiwalled carbon nanotubes (MWCNTs) supported catalysts polymerize ethylene to form polymer nanocomposite. MWCNTs were homogeneously dispersed within polymer matrix, and as expected, the resultant nanocomposites featured core–shell structure which was confirmed by HRTEM. For the nanocomposite, the microscopic examination of the cryogenically fractured surface not only ensured a good distribution of carbon nano-particles in the PE matrix but also revealed the ductile-like fracture. The Raman spectroscopy and X-ray photoelectron spectroscopy (XPS) were employed for the study of covalent sidewall functionalization and chemical bonding environment of MWCNTs, also indicated effective immobilization of titanium catalyst on the MWCNTs surface. The crystalline properties, dielectric property and thermal stability of the nanocomposites were determined by WAXD, impedance analyzer and TGA. The dielectric result showed a slight decline of the dielectric constant of the nanocomposites with increase of the polymerization time, and lower dielectric loss was also observed.     

Study of the anticorrosive efficiency of zincite and periclase-based core–shell pigments in organic coatings

The objective of this work was to identify the anticorrosive efficiency of synthesized, MeO/core pigments and of MeO pigments (MeO = ZnO, MgO) with varied morphology of particles. The synthesized MeO-type pigments displayed varied particle morphologies and the MeO/core core–shell pigments exhibited surface of particles made of zincite and periclase. These core–shell pigments have the properties of both the ZnO layer and of the core (wollastonite or graphite). Epoxy-ester based coatings containing the synthesized pigments were also formulated. To test the anticorrosion properties of the coatings, accelerated corrosion tests were carried out in the environment of condensed water, of NaCl mist, and of condensing water and SO₂. The synthesized core–shell pigments have good anticorrosion efficiency in an epoxy-ester coating.     

Preparation,mechanical properties and long-term ablation resistance of Cf/SiBCN–ZrB2 composites

The C_f/SiBCN–ZrB₂ composites were prepared by dipping and winding combined with reactive hot pressing. The flexural strength and fracture toughness reached 261 MPa and 11.96 MPa • m^1/2, respectively, through continuous carbon fibers debonding, pulling and bridging mechanisms. Excellent mechanical properties ensured that the C_f/SiBCN–ZrB₂ composites remained intact after exposure to a plasma flame with a heat flux of 9.37 MW/m² for 300 s, with the mass and linear ablation rates of 1.78 mg/s, 1.01 μm/s, respectively. The excellent ablation resistance was due to the formation of dense oxide layers separating the matrix from the plasma flame. The SiO₂ formed in the low-temperature areas away from the center was the main ablation-resistant barrier, while the ZrO₂/SiO₂ double oxide layer formed in the high-temperature region at the center was the major ablation-resistant barrier.     

Preparation of PVDF/PVP core–shell nanofibers mats via homogeneous electrospinning

The polyvinylpyrrolidone (PVP)/poly(vinylidene fluoride) (PVDF) core–shell nanofiber mats with superhydrophobic surface have been prepared via electrospinning its homogeneous blending solutions, and the formation of the core–shell structure was achieved by the thermal induced phase separation assisted with the low surface tension of PVDF. The electrospinnability of the blending solutions was also investigated by varying the blending ratio of the PVP and PVDF, and it enhanced with the increase of PVP content. SEM and TEM results showed that the fibers size was varied in the range of 100 nm–600 nm with smooth surface and core–shell structure. The composition of the shell layer was determined by the XPS analysis, and further confirmed by water contact angle (WCA) testing. As the fraction of PVDF exceeding PVP in the electrospinning solutions, the nanofiber mats showed superhydrophobic property with the WCA above 120°. It indicated that the PVDF was concentrated in the shell layer of the fibers. X-Ray diffraction (XRD) and attenuated total reflection infrared spectroscopy (ATR-IR) analysis indicated that the PVDF was aggregated with the β-phase crystallite as dominant crystallite. The nanofiber mats with the gas breathability and watertightness ability due to the porous structure and superhydrophobic would be potential applied in wound healing.     

Preparation and electrochemical performance of SnO2@carbon nanotube core–shell structure composites as anode material for lithium-ion batteries

Carbon nanotube-encapsulated SnO₂ (SnO₂@CNT) core–shell composite anode materials are prepared by chemical activation of carbon nanotubes (CNTs) and wet chemical filling. The results of X-ray diffraction and transmission electron microscopy measurements indicate that SnO₂ is filled into the interior hollow core of CNTs and exists as small nanoparticles with diameter of about 6 nm. The SnO₂@CNT composites exhibit enhanced electrochemical performance at various current densities when used as the anode material for lithium-ion batteries. At 0.2 mA cm^?2 (0.1C), the sample containing wt. 65% of SnO₂ displays a reversible specific capacity of 829.5 mAh g^?1 and maintains 627.8 mAh g^?1 after 50 cycles. When the current density is 1.0, 2.0, and 4.0 mA cm^?2 (about 0.5, 1.0, and 2.0C), the composite electrode still exhibits capacity retention of 563, 507 and 380 mAh g^?1, respectively. The capacity retention of our SnO₂@CNT composites is much higher than previously reported values for a SnO₂/CNT composite with the same filling yield. The excellent lithium storage and rate capacity performance of SnO₂@CNT core–shell composites make it a promising anode material for lithium-ion batteries.     

Preparation，properties and applications of hydroxyapatite/synthetic polymer composites

随着生物医用材料的需求量日趋增大,磷灰石与人工合成高分子的复合材料成为组织修复和替代材料的研究热点。以不同单体分类,综述了磷灰石与合成的非降解高分子、可降解高分子复合材料的研究进展;对羟基磷灰石/合成高分子复合材料的制备方法、性能及其应用等方面进行研究,并对此复合材料存在的问题和发展前景进行讨论。说明从分子水平设计出具有良好力学性能、生物活性和生物相容性的医学材料,具有十分重要的意义。     

Preparation of the stable core–shell latex particles containing organic-siloxane in the shell

In this study, the latex particles with a polyacrylate core and a polydimethylsiloxane shell via 3-(methacryloxypropyl)-trimethoxysilane as the space arm to link the core and shell have been prepared by semi continuous seeded emulsion polymerization. And several key polymerization reaction conditions such as the emulsifier concentration, 3-(methacryloxypropyl)-trimethoxysilane dosages, feeding sequence and the acrylates/siloxanes ratio were detailedly discussed. Then, the optimal condition to prepare stable core/shell particles was selected and a proper preparation process has been established. The as-synthesized particles were characterized by TEM and XPS. The clear core/shell structure of the particles could be observed through analysis TEM. In addition, the results of XPS analyses manifested that siloxanes had been grafted on the surface of the polyacrylate particles and they distributed on the outmost layer of the particles. Finally, the surface hydrophobicity of the film formed by latex particles was investigated by the water absorption ratio measurement. The results indicated the developed latex particle provided with a fair water-repellency property.     

Preparation and properties of DNA/PLLA,whey protein/PLLA and collagen/PLLA composites

The poor flexibility, low toughness and thermal stability have restricted the applications of degradable poly(lactic acid) bioplastic. The introduction of deoxyribonucleic acid, whey protein or collagen with helical structures, which include numerous intermolecular hydrogen bonds, can produce changes in mechanical and thermal properties of poly(lactic acid) materials. Due to the presence of more –C?=?O and –NH groups with strong hydratability, different composites exhibited a higher heat resistance compared with the neat poly(l-lactic acid). Moreover, for collagen/poly(l-lactic acid) composites, the tensile strength and elongation at break were increased by 88.6 and 154.9% compared with the neat poly(l-lactic acid), respectively. The results provide a basis for the design of novel poly(lactic acid)-based composites and can expand the application areas of materials, including plastic films, taker-bags, textiles and so on.     

Comparison of film properties for crosslinked core–shell latexes

Thermosetting acrylic latexes were synthesized using butyl acrylate (BA), methyl methacrylate (MMA), 2-hydroxyethyl methacrylate (HEMA), and methacrylic acid (MAA) via seeded two-stage process. A 2-level factorial experimental design was employed to investigate the effect of hydroxyl (core phase), carboxylate (shell phase) groups, and type of surfactant (Triton X200, Tergitol XJ) on the mechanical properties of thermosetting latexes. Eight latexes with varying concentration of HEMA, MAA and two types of surfactants were synthesized and crosslinked with three crosslinkers. Latex functionality for crosslinking was located in the core only, the shell only, and both the core–shell with varying concentrations. Melamine-formaldehyde (hexamethoxymethyl melamine) resin was employed to crosslink hydroxyl functionalities in the core. Carboxylic acid groups in the shell were crosslinked with zinc ammonium carbonate. HDI isocyanurate (Desmodur N3300A) were used to crosslink with hydroxyl or carboxyl functional groups in core and shell. The mechanical properties of coatings were evaluated in terms of tensile properties, cross-hatch adhesion, pencil hardness, and impact resistance. Design of experiment (DOE) was utilized to investigate the effect of variables on mechanical properties of crosslinked thermoset films.     

Shrinkage and mechanical properties of unsaturated polyester reinforced with clay and core–shell rubber

Glassy unsaturated polyester (UP) resin was reinforced using an organically modified montmorillonite (OMMT) and toughened with core?Cshell rubber (CSR) particles. The nanostructure, morphology, and deformation mechanism of composite specimens were studied by small-angle X-ray scattering (SAXS), transmission electron microscopy (TEM) and reflected optical microscopy (ROM). An intercalated nanostructure with partial exfoliation was observed in the UP reinforced by various amounts of OMMT. Locally clustered but globally good CSR particle dispersion in the UP matrix was evident in UP toughened with 5 and 10 wt% CSR particles. Simultaneous presence of OMMT and CSR particles in UP/OMMT/CSR hybrid composites was found to cause partial phase separation with bigger rubber particle agglomerates and lower clay-intergallery height increase. The effects of OMMT and CSR contents on volume shrinkage, impact fracture energy, fracture toughness, and compressive yield strength of UP were investigated. The introduction of OMMT of up to 3?wt% into the UP matrix lowered volume shrinkage to some extent, while further addition increased the shrinkage slightly. In the hybrid nanocomposites, the volume shrinkage decreased to a minimum level of 5.2?% with increases in OMMT level. The impact fracture energy of UP improved with increasing the OMMT level of up to 3?wt%, whereas its further addition decreased the impact fracture energy slightly due to the clay particle agglomeration. The hybrid composites with OMMT level below 3?wt% showed higher impact fracture energy compared to the reinforced UP specimens with the same OMMT levels. Interestingly, a synergism in the fracture toughness (K _IC) was observed in the hybrid composite containing 1?wt% OMMT and 10?wt% CSR particles. The presence of OMMT as reinforcement in the hybrid composites could compensate the lowering of the compressive yield strength caused by low-modulus CSR particles. The clay?Crubber particle interaction in the hybrid systems seems to increase the threshold of shear deformation of the UP matrix to some extent.