Reverse‐Offset Printed Ultrathin Ag Mesh for Robust Conformal Transparent Electrodes for High‐Performance Organic Photovoltaics

Mechanically durable transparent electrodes are needed in flexible optoelectronic devices to realize their long‐term stable functioning, for applications in various fields such as energy, healthcare, and soft robotics. Several promising transparent electrodes based on nanomaterials have been previously reported to replace the conventional and fragile indium‐tin oxide (ITO); however, obtaining feasible printed transparent electrodes for ultraflexible devices with a multistack structure is still a great challenge. Here, a printed ultrathin (uniform thickness of 100 nm) Ag mesh transparent electrode is demonstrated, simultaneously achieving high conductance, high transparency, and good mechanical properties. It shows a 17 Ω sq^?1 sheet resistance (R_sh) with 93.2% transmittance, which surpasses the performance of sputtered ITO electrodes and other ultrathin Ag mesh transparent electrodes. The conductance is stable after 500 cycles of 100% stretch/release deformation, with an insignificant increase (10.6%) in R_sh by adopting a buckling structure. Furthermore, organic photovoltaics (OPVs) using our Ag mesh transparent electrodes achieve a power conversion efficiency of 8.3%, which is comparable to the performance of ITO‐based OPVs.     

Junction‐Free Electrospun Ag Fiber Electrodes for Flexible Organic Light‐Emitting Diodes

Fabrication of junction‐free Ag fiber electrodes for flexible organic light‐emitting diodes (OLEDs) is demonstrated. The junction‐free Ag fiber electrodes are fabricated by electrospun polymer fibers used as an etch mask and wet etching of Ag thin film. This process facilitates surface roughness control, which is important in transparent electrodes based on metal wires to prevent electrical instability of the OLEDs. The transmittance and resistance of Ag fiber electrodes can be independently adjusted by controlling spinning time and Ag deposition thickness. The Ag fiber electrode shows a transmittance of 91.8% (at 550 nm) at a sheet resistance of 22.3 Ω □^?1, leading to the highest OLED efficiency. In addition, Ag fiber electrodes exhibit excellent mechanical durability, as shown by measuring the change in resistance under repeatable mechanical bending and various bending radii. The OLEDs with Ag fiber electrodes on a flexible substrate are successfully fabricated, and the OLEDs show an enhancement of EQE (≈19%) compared to commercial indium tin oxide electrodes.     

Stretchable Platinum Network‐Based Transparent Electrodes for Highly Sensitive Wearable Electronics

A platinum network‐based transparent electrode has been fabricated by electrospinning. The unique nanobelt structured electrode demonstrates low sheet resistance (about 16 Ω sq^?1) and high transparency of 80% and excellent flexibility. One of the most interesting demonstrations of this Pt nanobelt electrode is its excellent reversibly resilient characteristic. The electric conductivity of the flexible Pt electrode can recover to its initial value after 160% extending and this performance is repeatable and stable. The good linear relationship between the resistance and strain of the unique structured Pt electrode makes it possible to assemble a wearable high sensitive strain sensor. Present reported Pt nanobelt electrode also reveals potential applications in electrode for flexible fuel cells and highly transparent ultraviolet (UV) sensors.     

Chemical Intercalation of Topological Insulator Grid Nanostructures for High‐Performance Transparent Electrodes

2D layered nanomaterials with strong covalent bonding within layers and weak van der Waals' interactions between layers have attracted tremendous interest in recent years. Layered Bi₂Se₃ is a representative topological insulator material in this family, which holds promise for exploration of the fundamental physics and practical applications such as transparent electrode. Here, a simultaneous enhancement of optical transmittancy and electrical conductivity in Bi₂Se₃ grid electrodes by copper‐atom intercalation is presented. These Cu‐intercalated 2D Bi₂Se₃ electrodes exhibit high uniformity over large area and excellent stabilities to environmental perturbations, such as UV light, thermal fluctuation, and mechanical distortion. Remarkably, by intercalating a high density of copper atoms, the electrical and optical performance of Bi₂Se₃ grid electrodes is greatly improved from 900 Ω sq^?1, 68% to 300 Ω sq^?1, 82% in the visible range; with better performance of 300 Ω sq^?1, 91% achieved in the near‐infrared region. These unique properties of Cu‐intercalated topological insulator grid nanostructures may boost their potential applications in high‐performance optoelectronics, especially for infrared optoelectronic devices.     

Adaptive Fabrication of a Flexible Electrode by Optically Self‐Selected Interfacial Adhesion and Its Application to Highly Transparent and Conductive Film

A novel adaptive electrode fabrication method using optically self‐selected interfacial adhesion between a laser‐processed metal layer and polymer film is introduced to fabricate cost‐effectively a high‐resolution arbitrary electrode with high conductivity. The quality is close to that from vacuum deposition on a highly heat sensitive polymer film, with active response to various design requirements. A highly conductive metal film (resistivity: 3.6 μΩ cm) below a 5 μm line width with a uniform stepwise profile and mirror surface quality (R_rms: 5–6 nm) is fabricated on a cheap polymer film with a heat resistance limit of below 100 °C. Severe durability tests are successfully completed without using any adhesion promoters. Finally, a highly transparent and conductive electrode with a transparency above 95% and sheet resistance of less than 10 Ω sq^?1 is fabricated on a polymer film and on glass by using this method. These results can help realize a potential high‐throughput, low‐cost, solution‐processable replacement for transparent conductive oxides.     

A Biodegradable and Stretchable Protein‐Based Sensor as Artificial Electronic Skin for Human Motion Detection

Due to the natural biodegradability and biocompatibility, silk fibroin (SF) is one of the ideal platforms for on‐skin and implantable electronic devices. However, the development of SF‐based electronics is still at a preliminary stage due to the SF film intrinsic brittleness as well as the solubility in water, which prevent the fabrication of SF‐based electronics through traditional techniques. In this article, a flexible and stretchable silver nanofibers (Ag NFs)/SF based electrode is synthesized through water‐free procedures, which demonstrates outstanding performance, i.e., low sheet resistance (10.5 Ω sq^?1), high transmittance (>90%), excellent stability even after bending cycles >2200 times, and good extensibility (>60% stretching). In addition, on the basis of such advanced (Ag NFs)/SF electrode, a flexible and tactile sensor is further fabricated, which can simultaneously detect pressure and strain signals with a large monitoring window (35 Pa–700 kPa). Besides, this sensor is air‐permeable and inflammation‐free, so that it can be directly laminated onto human skins for long‐term health monitoring. Considering the biodegradable and skin‐comfortable features, this sensor may become promising to find potential applications in on‐skin or implantable health‐monitoring devices.     

Roll‐to‐Roll Production of Transparent Silver‐Nanofiber‐Network Electrodes for Flexible Electrochromic Smart Windows

Electrochromic smart windows (ECSWs) are considered as the most promising alternative to traditional dimming devices. However, the electrode technology in ECSWs remains stagnant, wherein inflexible indium tin oxide and fluorine‐doped tin oxide are the main materials being used. Although various complicated production methods, such as high‐temperature calcination and sputtering, have been reported, the mass production of flexible and transparent electrodes remains challenging. Here, a nonheated roll‐to‐roll process is developed for the continuous production of flexible, extralarge, and transparent silver nanofiber (AgNF) network electrodes. The optical and mechanical properties, as well as the electrical conductivity of these products (i.e., 12 Ω sq^?1 at 95% transmittance) are comparable with those AgNF networks produced via high‐temperature sintering. Moreover, the as‐prepared AgNF network is successfully assembled into an A4‐sized ECSW with short switching time, good coloration efficiency, and flexibility.     

Ultraflexible Transparent Bio‐Based Polymer Conductive Films Based on Ag Nanowires

The unstable mechanical properties of flexible transparent conductive films (TCFs) make it difficult for them to meet the requirements for displays or wearable devices. Here, the relationship between the mechanism behind the bending behavior and the electrical properties, which is important for improving the mechanical stability of flexible TCFs, is explored. Flexible TCFs are reported based on silver nanowires (AgNWs) and bio‐based poly(ethylene‐co‐1,4‐cyclohexanedimethylene 2,5‐furandicarboxylate)s (PECFs), with a low sheet resistance (23.8 Ω sq^?1 at 84.6% transmittance) and superior mechanical properties. The electrical properties of the AgNW/PECFs composite film show almost no change after bending for 2000 times.     

Visually Imperceptible Liquid‐Metal Circuits for Transparent,Stretchable Electronics with Direct Laser Writing

A material architecture and laser‐based microfabrication technique is introduced to produce electrically conductive films (sheet resistance = 2.95 Ω sq^?1; resistivity = 1.77 × 10^?6 Ω m) that are soft, elastic (strain limit >100%), and optically transparent. The films are composed of a grid‐like array of visually imperceptible liquid‐metal (LM) lines on a clear elastomer. Unlike previous efforts in transparent LM circuitry, the current approach enables fully imperceptible electronics that have not only high optical transmittance (>85% at 550 nm) but are also invisible under typical lighting conditions and reading distances. This unique combination of properties is enabled with a laser writing technique that results in LM grid patterns with a line width and pitch as small as 4.5 and 100 µm, respectively—yielding grid‐like wiring that has adequate conductivity for digital functionality but is also well below the threshold for visual perception. The electrical, mechanical, electromechanical, and optomechanical properties of the films are characterized and it is found that high conductivity and transparency are preserved at tensile strains of ≈100%. To demonstrate their effectiveness for emerging applications in transparent displays and sensing electronics, the material architecture is incorporated into a couple of illustrative use cases related to chemical hazard warning.     

Embedded Fin‐Like Metal/CNT Hybrid Structures for Flexible and Transparent Conductors

In this paper, an embedded fin‐like metal‐coated carbon nanotube (Fin‐M/CNT) structure is demonstrated for flexible and transparent conductor wire applications. Embedded in a polydimethylsiloxane polymeric substrate, Fin‐M/CNT wires with a minimum width of 5 μm and a minimum pitch of 10 μm have been achieved. Direct current resistances of single Fin‐M/CNT wires, where the supporting CNT structures have been covered by Ti/Al/Au metal coatings of different thicknesses, have been measured. The high aspect ratio of the fin‐like structures not only improves the adhesion between the wires and the polymeric substrate, but also yields a low resistance at a small surface footprint. In addition, transparent Fin‐M/CNT grid lines with hexagonal patterns, with a sheet resistance of as low as 45 Ω sq^?1, have been achieved at an optical transmittance of 88%. The robustness of the Fin‐M/CNT structures has been demonstrated in bending tests up to 500 cycles and no significant changes in wire resistances are observed.     

High‐Performance Flexible Transparent Electrode with an Embedded Metal Mesh Fabricated by Cost‐Effective Solution Process

A new structure of flexible transparent electrodes is reported, featuring a metal mesh fully embedded and mechanically anchored in a flexible substrate, and a cost‐effective solution‐based fabrication strategy for this new transparent electrode. The embedded nature of the metal‐mesh electrodes provides a series of advantages, including surface smoothness that is crucial for device fabrication, mechanical stability under high bending stress, strong adhesion to the substrate with excellent flexibility, and favorable resistance against moisture, oxygen, and chemicals. The novel fabrication process replaces vacuum‐based metal deposition with an electrodeposition process and is potentially suitable for high‐throughput, large‐volume, and low‐cost production. In particular, this strategy enables fabrication of a high‐aspect‐ratio (thickness to linewidth) metal mesh, substantially improving conductivity without considerably sacrificing transparency. Various prototype flexible transparent electrodes are demonstrated with transmittance higher than 90% and sheet resistance below 1 ohm sq^?1, as well as extremely high figures of merit up to 1.5 × 10⁴, which are among the highest reported values in recent studies. Finally using our embedded metal‐mesh electrode, a flexible transparent thin‐film heater is demonstrated with a low power density requirement, rapid response time, and a low operating voltage.     

H2O‐Etchant‐Promoted Synthesis of High‐Quality Graphene on Glass and Its Application in See‐Through Thermochromic Displays

Direct growth of graphene on glass can bring an innovative revolution by coupling the complementary properties of traditional glass and modern graphene (such as transparency and conductivity), offering brand new daily‐life related applications. However, preparation of high‐quality graphene on nonmetallic glass is still challenging. Herein, the direct route of low sheet resistance graphene on glass is reported by using in situ‐introduced water as a mild etchant and methane as a carbon precursor via chemical vapor deposition. The derived graphene features with large domain sizes and few amorphous carbon impurities. Intriguingly, the sheet resistance of graphene on glass is dramatically lowered down to ≈1170 Ω sq^?1 at the optical transmittance ≈93%, ≈20% of that derived without the water etchant. Based on the highly conductive and optical transparent graphene on glass, a see‐through thermochromic display is thus fabricated with transparent graphene glass as a heater. This work can motivate further investigations of the direct synthesis of high‐quality graphene on functional glass and its versatile applications in transparent electronic devices or displays.     

A Highly Stretchable Transparent Self‐Powered Triboelectric Tactile Sensor with Metallized Nanofibers for Wearable Electronics

Recently, the quest for new highly stretchable transparent tactile sensors with large‐scale integration and rapid response time continues to be a great impetus to research efforts to expand the promising applications in human–machine interactions, artificial electronic skins, and smart wearable equipment. Here, a self‐powered, highly stretchable, and transparent triboelectric tactile sensor with patterned Ag‐nanofiber electrodes for detecting and spatially mapping trajectory profiles is reported. The Ag‐nanofiber electrodes demonstrate high transparency (>70%), low sheet resistance (1.68–11.1 Ω □^?1), excellent stretchability, and stability (>100% strain). Based on the electrode patterning and device design, an 8 × 8 triboelectric sensor matrix is fabricated, which works well under high strain owing to the effect of the electrostatic induction. Using cross‐locating technology, the device can execute more rapid tactile mapping, with a response time of 70 ms. In addition, the object being detected can be made from any commonly used materials or can even be human hands, indicating that this device has widespread potential in tactile sensing and touchpad technology applications.     

Hybrid Copper‐Nanowire–Reduced‐Graphene‐Oxide Coatings: A “Green Solution” Toward Highly Transparent,Highly Conductive,and Flexible Electrodes for (Opto)Electronics

This study reports a novel green chemistry approach to assemble copper‐nanowires/reduced‐graphene‐oxide hybrid coatings onto inorganic and organic supports. Such films are robust and combine sheet resistances (<30 Ω sq^?1) and transparencies in the visible region (transmittance > 70%) that are rivalling those of indium–tin oxide. These electrodes are suitable for flexible electronic applications as they show a sheet resistance change of <4% after 10 000 bending cycles at a bending radius of 1.0 cm, when supported on polyethylene terephthalate foils. Significantly, the wet‐chemistry method involves the preparation of dispersions in environmentally friendly solvents and avoids the use of harmful reagents. Such inks are processed at room temperature on a wide variety of surfaces by spray coating. As a proof‐of‐concept, this study demonstrates the successful use of such coatings as electrodes in high‐performance electrochromic devices. The robustness of the electrodes is demonstrated by performing several tens of thousands of cycles of device operation. These unique conducting coatings hold potential for being exploited as transparent electrodes in numerous optoelectronic applications such as solar cells, light‐emitting diodes, and displays.     

Microgrid Electrode for Si Microwire Solar Cells with a Fill Factor of Over 80%

Here, a novel microgrid top electrode for highly efficient radial‐junction Si microwire solar cells is demonstrated. The microgrid electrode minimizes optical and electrical losses, thus ensuring proper function of the shallow (sheet resistance of ≈100 Ω sq⁻¹) junction emitter. This leads to effective collection of the photocarriers from the shallow junction emitter through the top electrode without severe Auger/surface recombination, improving the overall power conversion efficiency of the Si microwire solar cell. With an optimized microgrid structure, 1 cm² microwire solar cells show a conversion efficiency of up to 16.5%, with an open‐circuit voltage of 565.2 mV and a short‐circuit current density of 35.9 mA·cm⁻²; this conversion efficiency is 72% higher than that of solar cells with an edge electrode (9.6%). Further, an ≈1 μm thick Ni electrode that is formed by electroplating considerably reduces the metal and contact resistances, which reproducibly yields a fill factor of over 80% (max 81.2%). Thus, the use of a novel microgrid to construct an ideal metal/emitter interface presents a unique opportunity to develop highly efficient microwire solar cells.     

Enhancing the Performance of Stretchable Conductors for E‐Textiles by Controlled Ink Permeation

Delivery of electronic functionality to the human body using e‐textiles is important for realizing the future of wearable electronics. Printing is a promising process for large scale manufacturing of e‐textile since it enables arbitrary patterns using a simple and inexpensive process. However, conductive inks printed atop of textile are vulnerable to cracking because of the deformable and porous structure of textiles. The authors develop a mechanically and electrically robust wiring by controlling ink permeation in the structure of textile. This is done by adjusting the ink's solvent. The use of butyl carbitol acetate, with its low vapor pressure and boiling point, enables deep permeation into the textile. The sheet resistance is initially 0.06 Ω sq^?1, and the resistance increasing only 70 times after stretching to 450% strain. Finally, a four‐channel electromyogram (EMG) monitoring garment is demonstrated to show the potential of a large‐scale e‐textile device for health care and sports.     

Roll‐to‐Roll Production of Graphene Hybrid Electrodes for High‐Efficiency,Flexible Organic Photoelectronics

Despite nearly two decades of research, the absence of ideal, flexible, and transparent electrodes has been the biggest bottleneck for realizing flexible and printable electronics via roll‐to‐roll (R2R) method. A fabrication of poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate):graphene:ethyl cellulose (PEDOT:PSS:G:EC) hybrid electrodes by R2R process, which allows for the elimination of strong acid treatment. The high‐performance flexible printable electrode includes a transmittance (T) of 78% at 550 nm and a sheet resistance of 13 Ω sq⁻¹ with excellent mechanical stability. These features arise from the PSS interacting strongly with the ethyoxyl groups from EC promoting a favorable phase separation between PEDOT and PSS chains, and the highly uniform and conductive G:EC enable rearrangement of the PEDOT chains with more expanded conformation surrounded by G:EC via the π–π interaction between G:EC and PEDOT. The hybrid electrodes are fully functional as universal electrodes for outstanding flexible electronic applications. Organic solar cells based on the hybrid electrode exhibit a high power conversion efficiency of 9.4% with good universality for active layer. Moreover, the organic light‐emitting diodes and photodetector devices hold the same level to or outperform those based on indium tin oxide flexible transparent electrodes.     

Cryo‐Transferred Ultrathin and Stretchable Epidermal Electrodes

A simple cryo‐transfer method to fabricate ultrathin, stretchable, and conformal epidermal electrodes based on a combination of silver nanowires (AgNWs) network and elastomeric polymers is developed. This method can temporarily enable the soft elastomers with much higher elastic modulus and dimensional contraction through exploiting their glass‐transition behaviors. During this process, a much higher Von Mises stress can be loaded on AgNWs than usual, and the generated strong grip force can facilitate the complete transfer of AgNWs. Afterward, the thawed AgNWs and elastomer composites quickly recover to their soft state at room temperature. The obtained ultrathin and soft electrode with a thickness of 8.4 µm and transmittance of 90.8% at a sheet resistance of 13.2 Ω sq^?1 can tolerate a stretching strain of 70% and 50 000 repeated bending cycles, which meets rigorous requirements of epidermal applications. The as‐prepared epidermal electrodes are effective and comfortable for electrophysiological signal monitoring, and while showing excellent performance exceeding the commercialized gel electrodes.     

Embedded Nickel-Mesh Transparent Electrodes for Highly Efficient and Mechanically Stable Flexible Perovskite Photovoltaics: Toward a Portable Mobile Energy Source

The rapid development of Internet of Things mobile terminals has accelerated the market's demand for portable mobile power supplies and flexible wearable devices. Here, an embedded metal-mesh transparent conductive electrode (TCE) is prepared on poly(ethylene terephthalate) (PET) using a novel selective electrodeposition process combined with inverted film-processing methods. This embedded nickel (Ni)-mesh flexible TCE shows excellent photoelectric performance (sheet resistance of ≈0.2–0.5 Ω sq⁻¹ at high transmittance of ≈85–87%) and mechanical durability. The PET/Ni-mesh/polymer poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS PH1000) hybrid electrode is used as a transparent electrode for perovskite solar cells (PSCs), which exhibit excellent electric properties and remarkable environmental and mechanical stability. A power conversion efficiency of 17.3% is obtained, which is the highest efficiency for a PSC based on flexible transparent metal electrodes to date. For perovskite crystals that require harsh growth conditions, their mechanical stability and environmental stability on flexible transparent embedded metal substrates are studied and improved. The resulting flexible device retains 76% of the original efficiency after 2000 bending cycles. The results of this work provide a step improvement in flexible PSCs.     

Fabrication of High‐Performance Silver Mesh for Transparent Glass Heaters via Electric‐Field‐Driven Microscale 3D Printing and UV‐Assisted Microtransfer

Great challenges remain concerning the cost‐effective manufacture of high‐performance metal meshes for transparent glass heaters (TGHs). Here, a high‐performance silver mesh fabrication technique is proposed for TGHs using electric‐field‐driven microscale 3D printing and a UV‐assisted microtransfer process. The results show a more optimal trade‐off in sheet resistance (R_s = 0.21 Ω sq^?1) and transmittance (T = 93.9%) than for indium tin oxide (ITO) and ITO substitutes. The fabricated representative TGH also exhibits homogeneous and stable heating performance, remarkable environmental adaptability (constant R_s for 90 days), superior mechanical robustness (R_s increase of only 0.04 in harsh conditions–sonication at 100 °C), and strong adhesion force with a negligible increase in R_s (2–12%) after 100 peeling tests. The practical viability of this TGH is successfully demonstrated with a deicing test (ice cube: 21 cm³, melting time: 78 s, voltage and glass thickness: 4 V, 5 mm). All of these advantages of the TGHs are attributed to the successful fabrication of silver meshes with high resolution and high aspect ratio on the glass substrate using the thick film silver paste. The proposed technique is a promising new tool for the inexpensive fabrication of high‐performance TGHs.