Interference management via access control and mobility prediction in two-tier heterogeneous networks

Abstract： Two-tier heterogeneous networks （HetNets）, where the current cellular networks, i.e., macrocells, are overlapped with a large number of randomly distributed femtocells, can potentially bring significant benefits to spectral utilization and system capacity. The interference management and access control for open and closed femtocells in two-tier HetNets were focused. The contributions consist of two parts. Firstly, in order to reduce the uplink interference caused by MUEs （macrocell user equipments） at closed femtocells, an incentive mechanism to implement interference mitigation was proposed. It encourages femtoeells that work with closed-subscriber-group （CSG） to allow the interfering MUEs access in but only via uplink, which can reduce the interference significantly and also benefit the marco-tier. The interference issue was then studied in open-subscriber-group （OSG） femtocells from the perspective of handover and mobility prediction. Inbound handover provides an alternative solution for open femtocells when interference turns up, while this accompanies with PCI （physical cell identity） confusion during inbound handover. To reduce the PCI confusion, a dynamic PCI allocation scheme was proposed, by which the high handin femtocells have the dedicated PCI while the others share the reuse PCIs. A Markov chain based mobility prediction algorithm was designed to decide whether the femtoeell status is with high handover requests. Numerical analysis reveals that the UL interference is managed well for the CSG femtocell and the PCI confusion issue is mitigated greatly in OSG femtocell compared to the conventional approaches.     

Dielectric,piezoelectric, and ferroelectric properties of lanthanum-modified PZTFN ceramics

Specimens of Pb1-1.5xLax（Zr0.53 Ti0.47）1-y-zFeyNb2O3 （x = 0, 0.004, 0.008, 0.012, and 0.016, y = z = 0.01） （PZTFN） ceramics were synthesized by a semi-wet route. In the present study, the effect of La doping was investigated on the structural, microstructural, dielectric, piezoelectric, and ferroelectric properties of the ceramics. The results show that, the tetragonal （space group P4mm） and rhombohedral （space group R3c） phases are observed to coexist in the sample at x = 0.012. Microstructural investigations of all the samples reveal that La doping inhibits grain growth. Doping of La into PZTFN improves the dielectric, ferroelectric, and piezoelectric properties of the ceramics. The hys- teresis loops of all specimens exhibit nonlinear behavior. The dielectric, piezoelectric and ferroelectric properties show a maximum response atx 〉 0.012, which corresponds to the morphotropic phase boundary （MPB）.     

Microstructure and texture evolution in commercial-purity Zr 702 during cold rolling and annealing

Microstructure and texture evolution in commercial-purity Zr 702 during cold rolling and annealing was investigated by optical microscopy, transmission electron microscopy, and X-ray diffraction. The results showed that crystallographic slip was the predominant deformation mechanism in the early stage of deformation. Deformation twins started to form when the rolling reduction was larger than 38.9%; both the dislocation density and the number of twins increased with increasing rolling reduction. The initial texture of the Zr 702 plate consisted of the basal fiber component. During cold rolling the strength of the basal fiber first decreased and then increased with increasing rolling reduction. The cold-rolled sheets were fully recrystallized after being annealed at 550℃. The recrystallization temperature and the size of recrystallized grains decreased with increasing rolling reduction. A larger rolling reduction resulted in a higher grain growth rate when the annealing temperature increased from 550℃ to 700℃. The recrystallization texture was characterized by a major basal fiber and a minor {0113}〈2110〉 component. The strength of the recrystallization texture increased with increasing rolling reduction.     

Mechanism of separating muscovite and quartz by flotation

Flotation experiments were performed to investigate the separation of muscovite and quartz in the presence of dodecylamine（DDA）, tallow amine（TTA） and dodecyltrimethylammonium bromide（DTAC）. The adsorption mechanisms of these three kinds of amines on muscovite and quartz were studied by FT-IR spectrum analysis, contact angle measurement and molecular dynamics（MD） simulation. The results reveal that the separation of muscovite from quartz is feasible at strong acid pulp condition using amine collectors. TTA and DTAC show poorer collecting ability for flotation of the two minerals compared with DDA. Physical adsorption is found to be the main adsorption module of amine collectors on muscovite and quartz by FT-IR analysis. MD simulation results show a strong physical adsorption ability of DDA＋ cation on muscovite and quartz（muscovite（001）：-117.31 kJ/mol, quartz（100）：-89.43 kJ/mol）, while neutral DDA molecular can hardly absorb onto the surface of these two minerals. These findings provide a novel explanation for the flotation mechanism from the perspective of MD simulation.     

Fluidized bed coating efficiency and morphology of coatings for producing Al-based nanocomposite hollow spheres

Abstract： We performed fluidized bed coating ofAl-based nanoeomposite powder-binder suspensions onto polymer substrates. The effects of the type and amount of the binder and nanoparticle additive on the coating process efficiency and coating characteristics were investigated. The efficiency decreased from 52% to 49% as the processing time increased from 15 to 20 min. However, the amount and thickness of the coating also increased as the processing time and amount of the binder were increased. The addition of nanoparticles to the system decreased the thickness of the coating from 222 to 207 μm when polyvinyl alcohol （PVA） was used as a binder. The suspension containing 3wt% R-4410 binder exhibited the greatest efficiency of 60%.     

Characterization and recycling of nickel- and chromium-contained pickling sludge generated in production of stainless steel

Pickling sludge generated during the neutralization of pickling wastewater with calcium hydroxide in stainless steel pickling process was characterized using X-ray fluorescence spectrometry, X-ray diffractometry, scanning electron microscopy, thermogravimetry and differential scanning calorimetry, etc. The major compositions of pickling sludge are CaF2, CaSO4, Me（OH）, （M： Fe, Cr, Ni）, and the content of CaF2 is high in the sludge. The melting point of pickling sludge is about 1350℃ and the viscosity is about 0.14 Pa.s at 1450 ℃, which are comparatively lower than those of normal refining slag. After heat treatment, the contents of sulfur and fluorine in the pickling sludge were reduced, confirming the thermal decomposition of sulfate in the sludge. Fluorine in the sludge is reduced by the gaseous SiF4 and A1F3 generated through the reactions of CaF2 with SiO2 and Al2O3. The preliminary results from the reduction test indicate that the sulfur content in the steel is not affected by the presence of sulfur in the sludge. The recovery of nickel is about 40%, and the chromium content changes marginally due to the protective atmosphere under the reduction condition of chromic oxide. The pickling sludge is a potential auxiliary material for the production of stainless steel.     

Effects of magnetic fields on Fe-Si composite electrodeposition

Coatings containing Fe-Si particles were electrodeposited on 3.0wt% Si steel sheets under magnetic fields. The effects of magnetic flux density （MFD）, electrode arrangement and current density on the surface morphology, the silicon content in the coatings and the cathode current efficiency were investigated. When a magnetic field was applied parallel to the current and when the MFD was less than 0.5 T, numerous needle-like structures appeared on the coating surface. With increasing MFD, the needle-like structures weakened and were transformed into dome-shaped structures. Meanwhile, compared to results obtained in the absence of a magnetic field, the silicon content in the coatings significantly increased as the MFD was increased for all of the samples obtained using a vertical electrode system. However, in the case of an aclinic electrode system, the silicon content decreased. Furthermore, the cathode current efficiency was considerably diminished when a magnetic field was applied. A possible mechanism for these phenomena was discussed.     

Fabrication and densification enhancement of SiC-particulate-reinforced copper matrix composites prepared via the sinter-forging process

The fabrication of copper （Cu） and copper matrix silicon carbide （Cu/SiCp） particulate composites via the sinter-forging process was investigated. Sintering and sinter-forging processes were performed under an inert Ar atmosphere. The influence of sinter-forging time, temperature, and compressive stress on the relative density and hardness of the prepared samples was systematically investigated and subsequently compared with that of the samples prepared by the conventional sintering process. The relative density and hardness of the composites were enhanced when they were prepared by the sinter-forging process. The relative density values of all Cu/SiCp composite samples were observed to decrease with the increase in SiC content.     

Thermodynamics and density functional theory study of potassium dichromate interaction with galena

The adsorption heat and reaction rate constant of potassium dichromate on the surface of galena were studied. The results indicate that potassium dichromate tends to adsorption on the galena surface. The reaction order is only 0.08385, suggesting that the concentration of potassium dichromate has little influence on its adsorption on the galena surface. In addition, the simulation of CrO2 4- adsorption on the PbS （100） surface in the absence and presence of O2 was carried out by density functional theory （DFT）. The calculated results show that CrO2 4- species adsorb energetically at the Pb-S bond site, and the presence of O2 can enhance this adsorption.     

High-temperature performance prediction of iron ore fines and the ore-blending programming problem in sintering

The high-temperature performance of iron ore fmes is an important factor in optimizing ore blending in sintering. However, the application of linear regression analysis and the linear combination method in most other studies always leads to a large deviation from the desired results. In this study, the fuzzy membership functions of the assimilation ability temperature and the liquid fluidity were proposed based on the fuzzy mathematics theory to construct a model for predicting the high-temperature performance of mixed iron ore. Comparisons of the prediction model and experimental results were presented. The results illustrate that the prediction model is more accurate and effective than previously developed models. In addition, fuzzy constraints for the high-temperature performance of iron ore in this research make the results of ore blending more comparable. A solution for the quantitative calculation as well as the programming of fuzzy constraints is also introduced.     

Effect of annealing on the microstructure and mechanical properties of Mg-2.5Zn-0.5Y alloy

The microstructure and mechanical properties of extruded Mg-2.5Zn-0.5Y alloy before and after annealing treatments were investigated. The as-extruded alloy exhibits a yield tensile strength （YTS） of 305.9 MPa and an ultimate tensile strength （UTS） of 354.8 MPa, whereas the elongation is only 4%. After annealing, the YTS and UTS decrease to 150 MPa and 240 MPa, respectively, and the elongation increases to 28%. Interestingly, the annealed alloy maintains an acceptable stress level even after a much higher ductility is achieved. These excellent mechanical properties stem from the combined effects of fine α-Mg dynamic recrystallization （DRX） grains and a homogeneously distributed icosahedral quasicrystalline phase （I-phase） in the α-Mg DRX grains. In particular, the superior ductility originates from the coherent interface of I-phase and α-Mg and from the formation of the secondary twin {101 1}-{101 2}（38°〈1 2 10〉） in the tension twin {1012}.     

Modeling the effects of ore properties on water recovery in the thickening process

A better understanding of solid-liquid separation would assist in improving the thickening performance and perhaps water recovery as well. The present work aimed to develop an empirical model to study the effects of ore properties on the thickening process based on pilot tests using a column. A hydro-cyclone was used to prepare the required samples for the experiments. The model significantly predicted the experimental underflow solid content using a regression equation at a given solid flux and bed level for different samples, indicating that ore properties are the effective parameters in the thickening process. This work confirned that the water recovery would be increased about 5% by separating the feed into two parts, overflow and underflow, and introducing two different thickeners into them separately. This is duo to the fact that thickeners are limited by permeability and compressibility in operating conditions.     

Influences of synthesis methods and modifier addition on the properties of Ni-based catalysts supported on reticulated ceramic foams

A method of synthesizing Ni-based catalysts supported on α-Al2O3-based foams was developed. The foams were impregnated with aqueous solutions of metal chlorides under an air atmosphere using an aerosol route. Separate procedures involved calcination to form oxides and drying to obtain chlorides on the foam surface. The synthesized samples were subsequently reduced with hydrogen. With respect to the Ni/Al2O3 catalysts, the chloride reduction route enabled the formation ofa Ni coating without agglomerates or cracks. Further research included catalyst modification by the addition of Pd, Cu, and Fe. The influences of the additives on the degree of reduction and on the low-temperature reduction effectiveness （533 and 633 K） were examined and compared for the catalysts obtained from oxides and chlorides. Greater degrees of reduction were achieved with chlorides, whereas Pd was the most effective modifier among those investigated. The reduction process was nearly complete at 533 K in the sample that contained 0.1wt% Pd. A lower reduction temperature was utilized, and the calcination step was avoided, which may enhance the economical and technological aspects of the developed catalyst production method.     

Hydroxyapatite/alumina nanocrystalline composite powders synthesized by sol-gel process for biomedical applications

Hydroxyapatite/alumina nanocrystalline composite powders needed for various biomedical applications were successfully synthe- sized by sol-gel process. Structural and morphological investigations of the prepared composite powders were performed using X-ray dif- fractometer （XRD）, scanning electron microscopy （SEM）, X＇Pert HighScore software, and Clemex Vision image analysis software. The re- suits show that the crystallite size of the obtained composite powders is in the range of 25 to 90 nm. SEM evaluation shows that the obtained composite powders have a porous structure, which is very useful for biomedical applications. The spherical nanoparticles in the range of 60 to 800 nm are embedded in the agglomerated clusters of the prepared composite powders.     

Effects of sintering temperature on the microstructural evolution and wear behavior of WCp reinforced Ni-based coatings

This article focuses on the microstructural evolution and wear behavior of 50wt%WC reinforced Ni-based composites prepared onto 304 stainless steel substrates by vacuum sintering at different sintering temperatures. The microstructure and chemical composition of the coatings were investigated by X-ray diffraction （XRD）, differential thermal analysis （DTA）, scanning and transmission electron microscopy （SEM and TEM） equipped with energy-dispersive X-ray spectroscopy （EDS）. The wear resistance of the coatings was tested by thrust washer testing. The mechanisms of the decomposition, dissolution, and precipitation of primary carbides, and their influences on the wear resistance have been discussed. The results indicate that the coating sintered at 1175℃ is composed of fine WC particles, coarse M6C （M=Ni, Fe, Co, etc.） carbides, and discrete borides dispersed in solid solution. Upon increasing the sintering temperature to 1225℃, the microstructure reveals few incompletely dissolved WC particles trapped in larger M6C, Cr-rich lamellar M23C6, and M3C2 in the austenite matrix. M23C6 and M3C2 precipitates are formed in both the γ/M6C grain boundary and the matrix. These large-sized and lamellar brittle phases tend to weaken the wear resistance of the composite coatings. The wear behavior is controlled simultaneously by both abrasive wear and adhesive wear. Among them, abrasive wear plays a major role in the wear process of the coating sintered at 1175℃, while the effect of adhesive wear is predominant in the coating sintered at 1225℃.     

Basic dynamic characteristics and seismic design of anchorage system

Based on some assumptions, the dynamic governing equation of anchorage system is established. The calculation formula of natural frequency and the corresponding vibration mode are deduced. Besides, the feasibility of the theoretical method is verified by using a specific example combined with other methods. It is found that the low-order natural frequency corresponds to the first mode of vibration, and the high-order natural frequency corresponds to the second mode of vibration, while the third mode happens only when the physical and mechanical parameters of anchorage system meet certain conditions. With the increasing of the order of natural frequency, the influence on the dynamic mechanical response of anchorage system decreases gradually. Additionally, a calculating method, which can find the dangerous area of anchorage engineering in different construction sites and avoid the unreasonable design of anchor that may cause resonance, is proposed to meet the seismic precautionary requirements. This method is verified to be feasible and effective by being applied to an actual project. The study of basic dynamic features of anchorage system can provide a theoretical guidance for anchor seismic design and fast evaluation of anchor design scheme.     

Influence of gangue existing states in iron ores on the formation and flow of liquid phase during sintering

Gangue existing states largely affect the high-temperature characteristics of iron ores. Using a micro-sintering method and scan- ning electron microscopy, the effects of gangue content, gangue type, and gangue size on the assimilation characteristics and fluidity of liquid phase of five different iron ores were analyzed in this study. Next, the mechanism based on the reaction between gangues and sintering mate- dais was unraveled. The results show that, as the SiO2 levels increase in the iron ores, the lowest assimilation temperature （LAT） decreases, whereas the index of fluidity of liquid phase （IFL） increases. Below 1.5wt%, Al2O3 benefits the assimilation reaction, but higher concentra- tions proved detrimental. Larger quartz particles increase the SiO2 levels at the local reaction interface between the iron ore and CaO, thereby reducing the LAT. Quartz-gibbsite is more conductive to assimilation than kaolin. Quartz-gibbsite and kaolin gangues encourage the forma- tion of liquid-phase low-Al2O3-SFCA with high IFL and high-Al2O3-SFCA with low IFL, respectively.     

Preparation and characterization of PEGDE crosslinked silk fibroin film

To obtain water-insoluble silk fibroin(SF) materials, polyethylene glycol diglycidyl ether(PEG-DE) was selected as a crosslinking agent to prepare SF films(blends). The reaction conditions were optimized for the crosslinking of the SF molecules. The hot water stability of the blends was measured using BCA protein assay and gravimetric analysis. The molecular conformation and crystalline structure of the blends were analyzed by FTIR and XRD, respectively. When the mass ratio of SF:PEG-DE was 1.0:0.8, the hot water loss rate of the SF blends was minimized. PEG-DE could induce SF molecules to form β-sheets during the gel reaction process, resulting in improved crystallinity and hot water dissolved resistance of the blend films. In order to demonstrate the cytotoxicity of the chemical reagents used to crosslink SF, L929 cells were seeded on the blend film(SF:PEG-DE = 1:1) and cultured for 3 days. Cells of L929 readily adhered and spread in the fusiform on the blend film resulting in high cell viability. The extracted liquid from the SF porous film did not inhibit cell proliferation, as estimated by the MTT assay.     

A ternary TiO2/WO3/graphene nanocomposite adsorbent： facile preparation and efficient removal of Rhodamine B

Ternary TiO2/WO3/graphene （TWG） nanocomposites were prepared by a facile salt-ultrasonic assisted hydrothermal method. The products were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and nitrogen adsorption--desorption. Both anatase TiO2 and orthorhombic WO3 formed in the nanocomposites, along with a highly disordered overlay of individual graphene nanosheets. Polyhedral and spherical TiO/and WO3 nanoparticles of uniform size 10-30 nm were densely anchored to the graphene sheets. The maximum specific surface area of the products was 144.59 m2·g^-1. The products showed clear abilities for the removal of Rhodamine B in the absence of illumination. Furthermore, the adsorption activity of the products exhibited only a slight decrease after three successive cycles. The results demonstrate that the ternary nanocomposites could be used as a high-efficiency adsorbent for the removal of environmental contaminants.     

Desulfurization ability of refining slag with medium basicity

The desulfurization ability of refining slag with relative lower basicity （B） and Al2O3 content （B = 3.5-5.0; 20wt%-25wt% Al2O3） was studied. Firstly, the component activities and sulfide capacity （Cs） of the slag were calculated. Then slag-metal equilibrium experiments were carried out to measure the equilibrium sulfur distribution （Ls）. Based on the laboratorial experiments, slag composition was optimized for a better desulfurization ability, which was verified by industrial trials in a steel plant. The obtained results indicated that an MgO-saturated CaO-Al2O3-SiO2-MgO system with the basicity of about 3.5-5.0 and the Al2O3 content in the range of 20wt%-25wt% has high activity of CaO （αCaO）, with no deterioration of Cs compared with conventional desulfurization slag. The measured Ls between high-strength low-alloyed （HSLA） steel and slag with a basicity of about 3.5 and an Al2O3 content of about 20wt% and between HSLA steel and slag with a basicity of about 5.0 and an Al2O3 content of about 25wt% is 350 and 275, respectively. The new slag with a basicity of about 3.5-5.0 and an Al2O3 content of about 20wt% has strong desulfurization ability. In particular, the key for high-efficiency desulfurization is to keep oxygen potential in the reaction system as low as possible, which was also verified by industrial trials.