Size-dependent cytotoxicity of gold nanoparticles

Gold nanoparticles are widely used in biomedical imaging and diagnostic tests. Based on their established use in the laboratory and the chemical stability of Au(0), gold nanoparticles were expected to be safe. The recent literature, however, contains conflicting data regarding the cytotoxicity of gold nanoparticles. Against this background a systematic study of water-soluble gold nanoparticles stabilized by triphenylphosphine derivatives ranging in size from 0.8 to 15 nm is made. The cytotoxicity of these particles in four cell lines representing major functional cell types with barrier and phagocyte function are tested. Connective tissue fibroblasts, epithelial cells, macrophages, and melanoma cells prove most sensitive to gold particles 1.4 nm in size, which results in IC(50) values ranging from 30 to 56 microM depending on the particular 1.4-nm Au compound-cell line combination. In contrast, gold particles 15 nm in size and Tauredon (gold thiomalate) are nontoxic at up to 60-fold and 100-fold higher concentrations, respectively. The cellular response is size dependent, in that 1.4-nm particles cause predominantly rapid cell death by necrosis within 12 h while closely related particles 1.2 nm in diameter effect predominantly programmed cell death by apoptosis.     

Homogeneous detection of nucleic acids based upon the light scattering properties of silver-coated nanoparticle probes

Herein we report the development of a simple, rapid, homogeneous, and sensitive detection system for DNA based on the scattering properties of silver-amplified gold nanoparticle probes. The assay uses DNA-functionalized magnetic particle probes that act as scavengers for target DNA, which can be collected via a magnetic field. Once the DNA targets are isolated from the initial sample, they are sandwiched via hybridization by a second set of probes. The latter probes are 13-nm gold nanoparticles modified with a different target complementary DNA. Excess probes are removed through repetitive washing steps. The gold particles are dispersed in solution by dehybridization, corresponding to an assumed 1:1 ratio with the target DNA. Electroless deposition of silver on the surface of the gold probes results in particle growth, which increases their scattering efficiency with time. The scattering efficiency and the extinction signatures of the particle sizes are monitored as a function of time and correlated with target concentration. The limit of detection for this novel assay was determined to be 10 fM.     

Electrical detection of viral DNA using ultramicroelectrode arrays

A fully electrical array for voltammetric detection of redox molecules produced by enzyme-labeled affinity binding complexes is shown. The electronic detection is based on ultramicroelectrode arrays manufactured in silicon technology. The 200-microm circular array positions have 800-nm-wide interdigitated gold ultramicroelectrodes embedded in silicon dioxide. Immobilization of oligonucleotide capture probes onto the gold electrodes surfaces is accomplished via thiol-gold self-assembling. Spatial separation of probes at different array positions is controlled by polymeric rings around each array position. The affinity bound complexes are labeled with alkaline phosphatase, which converts the electrochemically inactive substrate 4-aminophenyl phosphate into the active 4-hydroxyaniline (HA). The nanoscaled electrodes are used to perform a sensitive detection of enzyme activity by signal enhancing redox recycling of HA resulting in local and position-specific current signals. Multiplexing and serial readout is realized using a CMOS ASIC module and a computer-controlled multichannel potentiostat. The principle of the silicon-based electrical biochip array is shown for different experimental setups and for the detection of virus DNA in real unpurified multiplex PCR samples. The fast and quantitative electronic multicomponent analysis for all kinds of affinity assays is robust and particle tolerant.     

Aptamer-based biosensors for label-free voltammetric detection of lysozyme

This paper reports a simple electrochemical approach for the detection of the ubiquitous protein lysozyme using aptamer-modified electrodes. Anti-lysozyme DNA aptamers were immobilized on gold surfaces by means of self-assembly, for which the surface density of aptamers was determined by cyclic voltammetric (CV) studies of redox cations (e.g., [Ru(NH3)6]3+) bound to the surface via electrostatic interaction with the DNA phosphate backbone. Upon incubation of the electrode with a solution containing lysozyme, the CV response of surface-bound [Ru(NH3)6]3+ changed substantially, and the relative decrease in the integrated charge of the reduction peak can be tabulated as a quantitative measure of the protein concentration. It is significant that the on-chip protein/aptamer binding constant and the optimized surface density to achieve the best detection limit can be evaluated. This biosensor is label-free and offers an alternative, sensitive, and versatile method for protein detection, which is beneficial to the ever-growing interests of fabricating portable bioanalytical devices with simple electrical readout protocols.     

Optical resonance-enhanced absorption-based near-field immunochip biosensor for allergen detection

An optical immunochip biosensor has been developed as a rapid method for allergen detection in complex food matrixes, and its application evaluated for the detection of the egg white allergens, ovalbumin and ovomucoid. The optical near-field phenomenon underlying the basic principle of the sensor design is called resonance-enhanced absorption (REA), which utilizes gold nanoparticles (Au NPs) as signal transducers in a highly sensitive interferometric setup. Using this approach, a novel, simple, and rapid colorimetric solid-phase immunoassay on a planar chip substrate was realized in direct and sandwich assay formats, with a detection system that does not require any instrumentation for readout. Semiquantitative immunochemical responses are directly visible to the naked eye of the analyst. The biosensor shows concentration-dependent color development by capturing antibody-functionalized Au NPs on allergen-coated chips and has a detection limit of 1 ng/mL. To establish a rapid method, we took advantage of the physicochemical microenvironment of the Au NP-antibody bioconjugate to be bound directly over an interacting poly(styrene-methyl methacrylate) interlayer by an immobilized antigen. In the direct assay format, a coating time with allergen of only 5 min under "soft" nondenaturing conditions was sufficient for accurate reproducibility and sensitivity. In conclusion, the REA-based immunochip sensor is easy to fabricate, is reproducible and selective in its performance, has minimal technical requirements, and will enable high-throughput screening of affinity binding interactions in technological and medical applications.     

Electrical Readout of Protein Microarrays on Regular Glass Slides

A new approach for the electrical readout of microarrays prepared on regular glass slides, using an array of impedimetric transducers (interdigitated electrodes, IDEs) is presented in this work. Impedance detection relies on the use of a urease-labeled immunoassay scheme. Urease is able to produce an increase in conductivity by hydrolysis of the urea substrate, which is measured with the IDEs and directly related to the amount of target analyte. Unlike previous electrical microarrays, the assay does not take place on top of the transducers but on a regular glass slide, which may enable the development of compact multiplexed analytical systems with lower cost per assay. A droplet of solution with the enzymatic substrate is deposited on each transducer of the array, and the microarray is positioned at a short distance (300 μm) so that each droplet wets one transducer and one spot of the microarray. This procedure allows reusing the transducer array for readout of a virtually unlimited number of microarrays. A microarray based on an immunoassay for the detection of a mouse generic protein in a concentration range from 0.03 to 30 μg mL(-1) was carried out to assess the performance of the electrical readout approach. A sigmoid response with a limit of detection of 0.1 μg mL(-1) and a dynamic range of 1 order of magnitude was obtained. A comparative study was also carried out with two well established analytical procedures. First, the urease-based immunoassay was tested in a 96 well microtiter plate using phenol red pH indicator and absorbance detection. Second, the microarray was carried out using the same target protein concentration range but applying a Cy3 label and fluorescence detection. Both assays allowed for the validation of the performance of the presented electrical readout system.     

Periodic square-like gold nanoparticle arrays templated by self-assembled 2D DNA Nanogrids on a surface

We report the use of a self-assembled two-dimensional (2D) DNA nanogrid as a template to organize 5-nm gold nanoparticles (Au NPs) into periodic square lattices. Each particle sits on only a single DNA tile. The center-to-center interparticle spacing between neighboring particles is controlled to be approximately 38 nm. These evenly distributed Au NP arrangements with accurate control of interparticle spacing may find applications in nanoelectronic and nanophotonic devices.     

Electrochemical coding of single-nucleotide polymorphisms by monobase-modified gold nanoparticles

Rapidly increasing information about the human genome requires a fast and simple method for the detection of single-nucleotide polymorphisms (SNPs). To date, the conventional SNP detection technologies have been unable to identify all possible SNPs and needed further development in cost, speed, and sensitivity. Here we describe a novel method to discriminate and code all possible combinations. SNPs were coded by monitoring the changes in the electrochemical signal of the monobase-modified colloidal gold (Au) nanoparticles. First, a chitosan layer was formed on the alkanethiol self-assembled monolayer-modified Au nanoparticle. The monobases were then attached onto the chitosan-coated Au nanoparticles through their 5' phosphate group via the formation of a phosphoramidate bond with the free amino groups of chitosan. The size of the surface-modified Au nanoparticle was found to be 8.46 +/- 1.53 nm by using atomic force microscopy. If there is a SNP in DNA and the mismatched bases are complementary to the monobase, Au nanoparticles accumulate on the electrode surface in the presence of DNA polymerase I (Klenow fragment), thus resulting in a significant change in the Au oxide wave. In this report, monobase-modified Au nanoparticles show not only the presence of a SNP, but also identify which bases are involved within the pair. Especially, the identification of a transversion SNP, which contains a couple of the same pyrimidine or purine bases, is greatly simplified. A model study was performed by using a synthetic 21-base DNA probe related to tumor necrosis factor (TNF-alpha) along with its all possible mutant combinations. This versatile nanoparticle-based electrochemical protocol is a promising candidate for coding all mutational changes.     

Improving the signal sensitivity and photostability of DNA hybridizations on microarrays by using dye-doped core-shell silica nanoparticles

The development of new highly sensitive and selective methods for microarray-based analysis is a great challenge because, for many bioassays, the amount of genetic material available for analysis is extremely limited. Currently, imaging and detection of DNA microarrays are based primarily on the use of organic dyes. To overcome the problems of photobleaching and low signal intensities of organic dyes, we developed a new class of silica core-shell nanoparticles that encapsulated with cyanine dyes and applied the dye-doped nanoparticles as labeling in the DNA microarray-based bioanalysis. The developed nanoparticles have core-shell structure containing 15-nm Au colloidal cores with 95 dye-alkanethiol (dT)20 oligomers chemisorbed on the each Au particle surface and 10-15-nm silica coatings bearing thiol functional groups. To be utilized for microarray detection, the dye-doped nanoparticles were conjugated with DNA signaling probes by using heterobifunctional cross-linker. The prepared nanoparticle conjugates are stable in both aqueous electrolytes and organic solvents. Two-color DNA microarray-based detection was demonstrated in this work by using Cy3- and Cy5-doped nanoparticles in sandwich hybridization. The use of the fluorophore-doped nanoparticles in high-throughput microarray detection reveals higher sensitivity with a detection limit of 1 pM for target DNA in sandwich hybridization and greater photostable signals than the direct use of organic fluorophore as labeling. A wide dynamic range of approximately 4 orders of magnitude was also found when the dye-doped nanoparticles were applied in microarray-based DNA bioanalysis. In addition, the use of these dye-doped nanoparticles as the labeling in hybridization also improved the differentiation of single-nucleotide polymorphisms. This work offers promising prospects for applying dye-doped nanoparticles as labeling for gene profiling based on DNA microarray technology.     

Quantitative enhanced Raman scattering of labeled DNA from gold and silver nanoparticles

Surface-enhanced resonance Raman scattering (SERRS) from silver nanoparticles using 514.5-nm excitation has been shown to offer huge potential for applications in highly sensitive multiplexed DNA assays. If the technique is to be applied to real biological samples and integrated with other methods, then the use of gold nanoparticles and longer wavelengths of excitation are desirable. The data presented here demonstrate that dye-labeled oligonucleotide sequences can be directly detected by SERRS using gold nanoparticles in a quantitative manner for the first time. The performance of gold and silver nanoparticles as SERRS substrates was assessed using 514.5-, 632.8-, and 785-nm excitation and a range of 13 commercially available dye-labeled oligonucleotides. The quantitative response allowed the limit of detection to be determined for each case and demonstrates that the technique is highly effective, sensitive, and versatile. The possibility of excitation at multiple wavelengths further enhances the multiplexing potential of the technique. The importance of effectively combining the optical properties of the nanoparticle and the dye label is demonstrated. For example, at 632.8-nm excitation, the dye BODIPY TR-X and gold nanoparticles make a strong SERRS combination with very little background fluorescence. This study allows the choice of nanoparticle and dye label for particular experimental setups, and significantly expands the applicability of enhanced Raman scattering for use in many disciplines.     

Ultrasensitive multiplexed immunoassay with electrochemical stripping analysis of silver nanoparticles catalytically deposited by gold nanoparticles and enzymatic reaction

A novel ultrasensitive multiplexed immunoassay method was developed by combining alkaline phosphatase (ALP)-labeled antibody functionalized gold nanoparticles (ALP-Ab/Au NPs) and enzyme-Au NP catalyzed deposition of silver nanoparticles at a disposable immunosensor array. The immunosensor array was prepared by covalently immobilizing capture antibodies on chitosan modified screen-printed carbon electrodes. After sandwich-type immunoreactions, the ALP-Ab/Au NPs were captured on an immunosensor surface to catalyze the hydrolysis of 3-indoxyl phosphate, which produced an indoxyl intermediate to reduce Ag(+). The silver deposition process was catalyzed by both ALP and Au NPs, which amplified the detection signal. The deposited silver was then measured by anodic stripping analysis in KCl solution. Using human and mouse IgG as model analytes, this multiplexed immunoassay method showed wide linear ranges over 4 orders of magnitude with the detection limits down to 4.8 and 6.1 pg/mL, respectively. Acceptable assay results for practical samples could be obtained. The newly designed strategy avoided cross talk and the need of deoxygenation for the electrochemical immunoassay and, thus, provided a promising potential in clinical applications.     

Chip-based electrical detection of DNA

A variety of methods have been developed for the detection of the binding of the complementary strand of DNA to a gene chip using electrical rather than the established optical signal techniques. Chip-based DNA sensors offer sensitivity, specificity, parallelisation and miniaturisation for the detection of selected DNA sequences or mutated genes associated with human diseases. Problems associated with the established fluorescence-based optical detection technique include the high equipment costs and the need to use sophisticated numerical algorithms to interpret the data. These problems generally limit its use to research laboratories and make it hard to adapt this detection scheme for on-site or point-of-care use. An electrical readout might be a solution to these problems. A review of a number of different approaches to achieve an electrical readout for a DNA chip is presented. The review covers various methods that are based on the use of metal nanoparticles as labels and also electrochemical methods that use polymer-modified electrodes, DNA-specific redox reporters, and DNA-mediated charge transport techniques.     

Voltammetric detection of metal nanoparticles separated by liquid chromatography

Fast-scan cyclic voltammetric (FSCV) detection of the separation of small (< 2-nm core diameter) organothiolate monolayer-protected gold clusters (MPCs) by high-performance liquid chromatography (HPLC) is demonstrated in this paper. Cyclic voltammograms taken at 1-s intervals (scan rate 150 V/s) display distinctive current-potential patterns for different MPCs, aiding in their identification. Previous amperometric detection of MPC separations required multiple HPLC runs at different electrode potentials to construct hydrodynamic current-potential voltammograms. Theory for ratiometric response of photodiode array absorbance and constant potential amperometry detectors was further tested on the fast-scan voltammetric detector and gave reasonable relative core size results for a mixture of Au140 and Au38 MPCs. In the first analysis of mixed MPC monolayer composition that is not simply an overall average result, preliminary HPLC experiments on MPCs with mixed hexanethiolate and ferrocenyl-octanethiolate monolayers resolved peaks that are shown to correspond to different average numbers of ferrocene-labeled ligands per MPC.     

Label-free detection of leptin antibody-antigen interaction by using LSPR-based optical biosensor

In the recent research, the development of optical biosensing devices has been focused on finding new method and technologies to exploit the optical properties of noble metal nanostructure, especially localized surface plasmon resonance (LSPR). In this study, we fabricated a LSPR-based label-free optical biosensor with the multi-spot gold-capped nanoparticle array (MG-NPA) biochip based on the deposition of a thin gold (Au) film on the silica nanoparticles layer with the simple process. The MG-NPA biochip used the silica nanoparticles as the core and a thin Au film as a shell on the surface. This structure can excite the LSPR signal easily with the high reproducibility. The anti-leptin antibody was immobilized on the surface of MG-NPA biochip, which could recognize only leptin antigen. The leptin antibody-antigen interaction was performed by the introduction of different concentration (1 pg/mL-100 microg/mL) of leptin antigen solutions for 1 h. The detection limit was found to be 100 pg/mL by using the anti-leptin antibody immobilized MG-NPA biochip. This LSPR-based label-free optical biosensor employing the MG-NPA biochip brings several advantages such as low cost, easy to fabricate, using a simple optical system and can be applied in a wide immunoassay with the similar antibody-antigen model.     

Microfluidic electrochemical aptameric assay integrated on-chip: a potentially convenient sensing platform for the amplified and multiplex analysis of small molecules

Aptamers are artificial oligonucleotides that have been widely employed to design biosensors (i.e., aptasensors). In this work, we report a microfluidic electrochemical aptamer-based sensor (MECAS) by constructing Au-Ag dual-metal array three-electrode on-chip for multiplex detection of small molecules. In combination with the microfluidic channels covering on the glass chip, different targets are transported to the Au electrodes integrated on different positions of the chip. These electrodes are premodified by different kinds of aptamers, respectively, to fabricate different sensing interfaces which can selectively capture the corresponding target. It is an address-dependent sensing platform; thus, with the use of only one electrochemical probe, multitargets can be recognized and detected according to the readout on a corresponding aptamer-modified electrode. In the sensing strategy, the electrochemical probe, [Ru(NH(3))(6)](3+) (RuHex), which can quantitatively bind to surface-confined DNA via electrostatic interaction, was used to produce chronocoulometric signal; Au nanoparticles (AuNPs) were used to improve the sensitivity of the sensor by amplifying the detection signals. Moreover, the sensing interface fabrication, sample incubation, and electrochemical detection were all performed in microfluidic channels. By using this detection chip, we achieved the multianalysis of two model small molecules, ATP, and cocaine, in mixed samples within 40 min. The detection limit of ATP was 3 × 10(-10) M, whereas the detection limit of cocaine was 7 × 10(-8) M. This Au-Ag dual metal electrochemical chip detector integrated MECAS was simple, sensitive, and selective. Also it is similar to a dosimeter which accumulates signal upon exposure. It held promising potential for designing electrochemical devices with high throughput, high automation, and high integration in multianalysis.     

Detection of mercury(II) by quantum dot/DNA/gold nanoparticle ensemble based nanosensor via nanometal surface energy transfer

An ultrasensitive fluorescent sensor based on the quantum dot/DNA/gold nanoparticle ensemble has been developed for detection of mercury(II). DNA hybridization occurs when Hg(II) ions are present in the aqueous solution containing the DNA-conjugated quantum dots (QDs) and Au nanoparticles. As a result, the QDs and the Au nanoparticles are brought into the close proximity, which enables the nanometal surface energy transfer (NSET) from the QDs to the Au nanoparticles, quenching the fluorescence emission of the QDs. This nanosensor exhibits a limit of detection of 0.4 and 1.2 ppb toward Hg(II) in the buffer solution and in the river water, respectively. The sensor also shows high selectivity toward the Hg(II) ions.     

Distance-dependent metal-enhanced quantum dots fluorescence analysis in solution by capillary electrophoresis and its application to DNA detection

Here the distance dependence of metal-enhanced quantum dots (QDs) fluorescence in solution is studied systematically by capillary electrophoresis (CE). Complementary DNA oligonucleotides-modified CdSe/ZnS QDs and gold nanoparticles (Au NPs) were connected together in solution by the hybridization of complementary oligonucleotides, and a model system (QD-Au) for the study of metal-enhanced QDs fluorescence was constructed, in which the distance between the QDs and Au NPs was controlled by adjusting the base number of the oligonucleotide. In our CE experiments, the metal-enhanced fluorescence of the QDs solution was only observed when the distance between the QDs and Au NPs ranged from 6.8 to 18.7 nm, and the maximum enhancement by a factor of 2.3 was achieved at 11.9 nm. Furthermore, a minimum of 19.6 pg of target DNA was identified in CE based on its specific competition with the QD-DNA in the QD-Au system. This work provides an important reference for future study of metal-enhanced QDs fluorescence in solution and exhibits potential capability in nucleic acid hybridization analysis and high-sensitivity DNA detection.     

Nanovolume analysis with secondary ion mass spectrometry using massive projectiles

A variant of secondary ion mass spectrometry is presented where the surface is bombarded with individual gold nanoparticles each resolved in time and space with a corresponding event-by-event detection of the secondary ions (SIs). The projectile used, Au400(4+), with impact energy of 136 keV, generates high SI yields. Typically, there is co-emission of multiple SIs from a single impact, i.e., emission of SIs from molecules co-located within a nanovolume with dimensions in the 10-nm range. The ability to detect co-located molecules was tested on samples consisting of alternating nanometric layers of oppositely charged polyions, poly(diallyldimethylammonium chloride), poly(styrenesulfonate) (PSS), and clay nanoplatelets. To achieve signal statistics, the chemical analysis was carried out with a sequence of stochastic impacts making this method suitable for characterization of similar nanoparticles or spots dispersed on a surface. Attomole detection sensitivity was achieved for PSS. The homogeneity of assembled layers could be assessed with approximately 10-nm resolution.     

Ultrasensitive flow injection chemiluminescence detection of DNA hybridization using signal DNA probe modified with Au and CuS nanoparticles

A novel and sensitive flow injection chemiluminescence assay for sequence-specific DNA detection based on signal amplification with nanoparticles (NPs) is reported in the present work. The "sandwich-type" DNA biosensor was fabricated with the thiol-functionalized capture DNA first immobilized on an Au electrode and hybridized with one end of target DNA, the other end of which was recognized with a signal DNA probe labeled with CuS NPs and Au NPs on the 3'- and 5'-terminus, respectively. The hybridization events were monitored by the CL intensity of luminol-H2O2-Cu(2+) after the cupric ions were dissolved from the hybrids. We demonstrated that the incorporation of Au NPs in this sensor design significantly enhanced the sensitivity and the selectivity because a single Au NP can be loaded with hundreds of signal DNA probe strands, which were modified with CuS NPs. The ratios of Au NPs, signal DNA probes, and CuS NPs modified on the gold electrode were approximately 1/101/103. A preconcentration process of cupric ions performed by anodic stripping voltammetry technology further increased the sensor performance. As a result of these two combined effects, this DNA sensor could detect as low as femtomolar target DNA and exhibited excellent selectivity against two-base mismatched DNA. Under the optimum conditions, the CL intensity was increased with the increase of the concentration of target DNA in the range of 2.0 x 10(-14)-2.0 x 10(-12) M. A detection limit of 4.8 x 10(-15) M target DNA was achieved.     

Gold and magnetic oxide/gold core/shell nanoparticles as bio-functional nanoprobes

The ability to create bio-functional nanoprobes for the detection of biological reactivity is important for developing bioassay and diagnostic methods. This paper describes the findings of an investigation of the surface functionalization of gold (Au) and magnetic nanoparticles coated with gold shells (M/Au) by proteins and spectroscopic labels for the creation of nanoprobes for use in surface enhanced Raman scattering (SERS) assays. Highly monodispersed Au nanoparticles and M/Au nanoparticles with two types of magnetic nanoparticle cores (Fe(2)O(3) and MnZn ferrite) were studied as model systems for the bio-functionalization and Raman labeling. Comparison of the SERS intensities obtained with different particle sizes (30-100?nm) and samples in solution versus on solid substrates have revealed important information about the manipulation of the SERS signals. In contrast to the salt-induced uncontrollable and irreversible aggregation of nanoparticles, the ability to use a centrifugation method to control the formation of stable small clustering sizes of nanoparticles was shown to enhance SERS intensities for samples in solution as compared with samples on solid substrates. A simple method for labeling protein-capped Au nanoparticles with Raman-active molecules was also described. The functionalized Au and M/Au nanoparticles are shown to exhibit the desired functional properties for the detection of SERS signals in the magnetically separated reaction products. These results are discussed in terms of the interparticle distance dependence of 'hot-spot' SERS sites and the delineation of the parameters for controlling the core-shell reactivity of the magnetic functional nanocomposite materials in bio-separation and spectroscopic probing.