Biodiesel production using tetramethyl- and benzyltrimethyl ammonium hydroxides as strong base catalysts

In recent years, the acceptance of fatty acid methyl esters (biodiesel) as an alternative fuel has rapidly grown in EU. The most common method for biodiesel production is based on triglyceride transesterification to methyl esters with dissolved sodium hydroxide in methanol as catalyst. In this study, cottonseed oil and used frying oil were subjected to the transesterification reaction with tetramethyl ammonium hydroxide and benzyltrimethyl ammonium hydroxide as strong base catalysts. This work investigates the optimum conditions for biodiesel production using amine-based liquid catalysts. Biodiesel ester content was strongly related with the type of feedstock and the reaction variables, such as those of the catalyst concentration, methanol to oil molar ratio, and reaction time. The overall results suggested that the transesterification of cottonseed oil achieved high conversion rates with both catalysts, while the use of waste oil resulted in lower yields of methyl esters due to the possible formation of amides.     

Rape oil transesterification over heterogeneous catalysts

This work studies the application of KNO₃/CaO catalyst in the transesterification reaction of triglycerides with methanol. The objective of the work was characterizing the methyl esters for its use as biodiesel in compression ignition motors. The variables affecting the methyl ester yield during the transesterification reaction, such as, amount of KNO₃ impregnated in CaO, the total catalyst content, reaction temperature, agitation rate, and the methanol/oil molar ratio, were investigated to optimize the reaction conditions.The evolution of the process was followed by gas chromatography, determining the concentration of the methyl esters at different reaction times. The biodiesel was characterized by its density, viscosity, cetane index, saponification value, iodine value, acidity index, CFPP (cold filter plugging point), flash point and combustion point, according to ISO norms. The results showed that calcium oxide, impregnated with KNO₃, have a strong basicity and high catalytic activity as a heterogeneous solid base catalyst.The biodiesel with the best properties was obtained using an amount of KNO₃ of 10% impregnated in CaO, a methanol/oil molar ratio of 6:1, a reaction temperature of 65 °C, a reaction time of 3.0 h, and a catalyst total content of 1.0%. In these conditions, the oil conversion was 98% and the final product obtained had very similar characteristics to a no. 2 diesel, and therefore, these methyl esters might be used as an alternative to fossil fuels.     

Transesterification of karanja (Pongamia pinnata) oil by solid basic catalysts

The transesterification of karanja oil with methanol was carried out using solid basic catalysts. Alkali metal‐impregnated calcium oxide catalysts, due to their strong basicity, catalyze the transesterification of triacylglycerols. The alkali metal (Li, Na, K)‐doped calcium oxide catalysts were prepared and used for the transesterification of karanja oil containing 0.48–5.75% of free fatty acids (FFA). The reaction conditions, such as catalyst concentration, reaction temperature and molar ratio of methanol/oil, were optimized with the solid basic Li/CaO catalyst. This catalyst, at a concentration of 2 wt‐%, resulted in 94.9 wt‐% of methyl esters in 8 h at a reaction temperature of 65 °C and a 12 : 1 molar ratio of methanol to oil, during methanolysis of karanja oil having 1.45% FFA. The yield of methyl esters decreased from 94.9 to 90.3 wt‐% when the FFA content of karanja oil was increased from 0.48 to 5.75%. The performance of this catalyst was not significantly affected in the presence of a high FFA content up to 5.75%. The catalytic activities of Na/CaO and K/CaO were also studied at the optimized reaction conditions. In these two cases, the reaction initially proceeds slowly, however, leading to similar yields as in the case of Li/CaO after 8 h of reaction time. The purified karanja methyl esters have an acid value of 0.36 mg KOH/g and an ester content of 98.6 wt‐%, which satisfy the American as well as the European specifications for biodiesel in terms of acid value and ester content.     

酸催化制备生物柴油的研究

采用硫酸作催化剂,利用高酸值油脂与甲醇的酯交换反应,制备生物柴油。为了提高收率,采用了两次酯交换反应;考察了醇油摩尔比、催化剂用量、反应温度等因素对收率的影响。结果表明,当醇与油的摩尔比为1∶10,催化剂用量0.5%,反应时间2.0 h,反应温度150℃,压力0.4~0.6 MPa时,生物柴油的收率可达98%。     

Conversion of waste cooking oil to biodiesel using ferric sulfate and supercritical methanol processes

In this comparative study, conversion of waste cooking oil to methyl esters was carried out using the ferric sulfate and the supercritical methanol processes. A two-step transesterification process was used to remove the high free fatty acid contents in the waste cooking oil (WCO). This process resulted in a feedstock to biodiesel conversion yield of about 85-96% using a ferric sulfate catalyst. In the supercritical methanol transesterification method, the yield of biodiesel was about 50-65% in only 15 min of reaction time. The test results revealed that supercritical process method is probably a promising alternative method to the traditional two-step transesterification process using a ferric sulfate catalyst for waste cooking oil conversion. The important variables affecting the methyl ester yield during the transesterification reaction are the molar ratio of alcohol to oil, the catalyst amount and the reaction temperature. The analysis of oil properties, fuel properties and process parameter optimization for the waste cooking oil conversion are also presented.     

固体碱催化黄连木籽油制备生物柴油

制备了K2CO3/Mg(A l)O固体碱催化剂,适宜制备条件为:K2CO3负载量30%、在700℃下焙烧4 h。用比表面积测定仪、X射线衍射仪、红外光谱仪对其进行了表征。以黄连木籽油为原料,开展了酯交换法制备生物柴油的研究,考察了主要影响因素:醇油摩尔比、催化剂用量、反应时间和反应温度对酯交换反应的影响,得到的酯交换反应适宜条件为:以黄连木籽油0.01 mol计,醇油摩尔比12∶1、催化剂用量为黄连木籽油质量的4.0%、反应时间2.5 h、反应温度68℃。在该条件下生物柴油的收率可达99%以上。催化剂经4次循环使用,生物柴油收率仍可保持在96%以上。用FTIR1、HNMR对所制备的产品进行了表征,证明产品中含有饱和脂肪酸甲酯和不饱和脂肪酸甲酯。     

利用废豆油制备生物柴油

研究了利用废豆油和甲醇作为原料,在催化剂甲醇钠的作用下通过酯交换反应,制备脂肪酸甲酯即生物柴油和丙三醇(甘油),根据正交实验结果,较佳的工艺条件为:摩尔比7∶1、反应温度60℃、反应时间90min、催化剂用量0.8%。在此工艺条件下,生物柴油的收率可达93.71%;精馏后的甘油纯度较高,达到97.5%以上。     

脂肪酶催化非食用植物油制备生物柴油的过程优化

以麻疯树油、亚麻油、乌柏油为原料油,采用固定化脂肪酶Lipozyme TL IM,在3.0 g油、1 mL正己烷、醇油摩尔比为3.5∶1、固定化酶质量为油质量20%的条件下进行生物柴油的制备,通过脂肪酸甲酯产率和组成分析,以考察生物柴油制备的影响因素,进行反应时间优化.结果表明,酶的催化作用对脂肪酸组分不存在选择性,且...     

Transesterification of the crude Jatropha curcas L. oil catalyzed by micro‐NaOH in supercritical and subcritical methanol

Transesterification of the crude Jatropha curcas L. oil catalyzed by micro‐NaOH in supercritical/subcritical methanol was studied. The effects of various reaction variables such as the catalyst content, reaction temperature, reaction pressure and the molar ratio of methanol to oil on the conversion of crude Jatropha curcas L. oil to biodiesel were investigated. The results showed that even micro‐NaOH could noticeably improve this reaction. When NaOH was added from 0.2 to 0.5 to 0.8 wt‐‰ of triacylglycerols, the transesterification rate increased sharply; when the catalyst content was further increased, the reaction rate was just poorly improved. It was observed that increasing the reaction temperature had a favorable influence on the methyl ester yield. For the molar ratio ranging from 18 to 36, the higher the molar ratio of methanol to oil was charged, the faster the transesterification rate seemed. At the fixed stirring rate of 400 rpm, when the catalyst content, reaction temperature, reaction pressure and the molar ratio of methanol to oil were developed at 0.8 wt‐‰ NaOH, 523 K, 7.0 MPa and 24 : 1, respectively, the methyl ester yield could reach 90.5% within 28 min. Further, the kinetics of this reaction was involved and the results showed that it was a pseudo‐first‐order reaction whose apparent activation energy was 84.1 kJ/mol, and the pre‐exponential factor was 2.21×10⁵.     

Production of mixed methyl/ethyl esters from waste fish oil through transesterification with mixed methanol/ethanol system

Biodiesel (mixed fatty acid methyl/ethyl esters) was prepared from waste fish oil through base-catalyzed transesterification with mixed methanol/ethanol system. Effect of methanol/ethanol (% v/v), type and concentration of the catalyst, mixed alcohols to oil molar ratio, the reaction temperature, and the reaction time on the biodiesel yield was optimized. Maximum biodiesel yield (97.30?wt%) was produced by implementing 1:1 methanol/ethanol (v/v), 1.0?wt% KOH, 6:1 mixed alcohols to oil molar ratio, 40°C reaction temperature, and 30?min of reaction time. Conversion of the waste fish oil to mixed methyl/ethyl esters was confirmed by ¹H NMR spectroscopy. Fuel properties of the resulting biodiesel in addition to its blends with petrodiesel were in good agreement with specifications of ASTM D6751 and ASTM D7467, respectively. Therefore, it was concluded that using mixed alcohol system for biodiesel production could reduce the production cost through reducing conditions required for maximum conversion.     

亚临界甲醇中麻疯树油制备生物柴油的研究

对麻疯树油在催化剂对甲苯磺酸作用下与亚临界甲醇反应制备脂肪酸甲酯(生物柴油)进行了研究。结果表明在反应温度170℃、醇油摩尔比40:1、催化剂用量占油重的0.75%和反应时间30 m in的条件下,反应产物中脂肪酸甲酯含量可达93%以上。制备的生物柴油,各项指标与柴油相似。主要性能指标,符合ASTMPS121-99(USA)和0#矿物柴油标准。     

Production of biodiesel through optimized alkaline-catalyzed transesterification of rapeseed oil

Present work reports an optimized protocol for the production of biodiesel through alkaline-catalyzed transesterification of rapeseed oil. The reaction variables used were methanol/oil molar ratio (3:1-21:1), catalyst concentration (0.25-1.50%), temperature (35-65 °C), mixing intensity (180-600 rpm) and catalyst type. The evaluation of the transesterification process was followed by gas chromatographic analysis of the rapeseed oil fatty acid methyl esters (biodiesel) at different reaction times. The biodiesel with best yield and quality was produced at methanol/oil molar ratio, 6:1; potassium hydroxide catalyst concentration, 1.0%; mixing intensity, 600 rpm and reaction temperature 65 °C. The yield of the biodiesel produced under optimal condition was 95-96%. It was noted that greater or lower the concentration of KOH or methanol than the optimal values, the reaction either did not fully occur or lead to soap formation.The quality of the biodiesel produced was evaluated by the determinations of important properties such as density, specific gravity, kinematic viscosity, higher heating value, acid value, flash point, pour point, cloud point, combustion point, cold filter plugging point, cetane index, ash content, sulphur content, water content, copper strip corrosion value, distillation temperature and fatty acid composition. The produced biodiesel was found to exhibit fuel properties within the limits prescribed by the latest American Standards for Testing Material (ASTM) and European EN standards.     

Evaluation of biodiesel obtained from cottonseed oil

Esters from vegetable oils have attracted a great deal of interest as substitutes for petrodiesel to reduce dependence on imported petroleum and provide a fuel with more benign environmental properties. In this work biodiesel was prepared from cottonseed oil by transesterification with methanol, using sodium hydroxide, potassium hydroxide, sodium methoxide and potassium methoxide as catalysts. A series of experiments were conducted in order to evaluate the effects of reaction variables such as methanol/oil molar ratio (3:1–15:1), catalyst concentration (0.25–1.50%), temperature (25–65 °C), and stirring intensity (180–600 rpm) to achieve the maximum yield and quality. The optimized variables of 6:1 methanol/oil molar ratio (mol/mol), 0.75% sodium methoxide concentration (wt.%), 65 °C reaction temperature, 600 rpm agitation speed and 90 min reaction time offered the maximum methyl ester yield (96.9%). The obtained fatty acid methyl esters (FAME) were analyzed by gas chromatography (GC) and ¹H NMR spectroscopy. The fuel properties of cottonseed oil methyl esters (COME), cetane number, kinematic viscosity, oxidative stability, lubricity, cloud point, pour point, cold filter plugging point, flash point, ash content, sulfur content, acid value, copper strip corrosion value, density, higher heating value, methanol content, free and bound glycerol were determined and are discussed in the light of biodiesel standards such as ASTM D6751 and EN 14214.     

响应面法优化碱催化酯交换反应制备生物柴油工艺研究

根据中心组合试验设计原理，通过30个试验，其中有6个样本的中心点，以甲酯含量作为响应值。考察反应时间、催化剂用量、反应温度和醇油摩尔比对碱催化酯交换反应的影响，确定碱催化酯交换反应制备生物柴油的二阶多项式模型。试验结果很好地拟合模型及对99％以上的差异做了解释，优化工艺参数的反应时间为45min、催化剂用量为1．5％、反应温度50℃、醇油摩尔比为7．5，试验值在95％的置信区间符合预测值。结果表明，RSM优化的模型适合于碱催化酯交换反应制备生物柴油工艺，能够预测不同条件下碱催化酯交换反应得到甲酯含量。     

新型固体碱铝酸钙催化剂用于生物柴油的制备研究

采用化学合成法制备了铝酸钙固体催化剂,并将其用于菜籽油与甲醇酯交换反应的研究.考察了酯交换反应的条件,实验结果表明,当醇/油摩尔比为15:1,催化剂质茸分数6%,反应温度65℃,搅拌速率270 r/min,反应时间3 h,甲酯的收率为89.05%.产物和催化剂固液分离简单容易,铝酸钙固体催化剂具有较好的稳定性,连续使用7次,甲酯的收率均在87.00%以上.同时采用Hammett指示剂法、XRD、BET等手段对铝酸钙同体催化剂进行了表征.     

Optimization of transesterification for methyl ester production from chicken fat

In this study, low cost feedstock chicken fat was used to produce methyl ester. After reducing the free fatty acid level of the chicken fat less than 1%, the transesterification reaction was completed with alkaline catalyst. Potassium hydroxide, sodium hydroxide, potassium methoxide and sodium methoxide were used as catalyst and methanol was used as alcohol for transesterification reactions. The effects of catalyst type, reaction temperature and reaction time on the fuel properties of methyl esters were investigated. The produced chicken fat methyl esters were characterized by determining their viscosity, density, pour point, flash point, acid value, methanol content, heat of combustion value, total-free glycerin, mono-di-tri glycerides, copper strip corrosion and ester yield values. The measured fuel properties of the chicken fat methyl ester met EN 14214 and ASTM D6751 biodiesel specifications when using potassium hydroxide and sodium hydroxide catalysts with high ester yield.     

Transesterification of the crude oil of rapeseed with NaOH in supercritical and subcritical methanol

Transesterification reaction of the crude oil of rapeseed with supercritical/subcritical methanol in the presence of a relatively low amount of NaOH was successfully carried out, where soap formation didn't occur. The main factors affecting the methyl ester yield during the transesterification reaction were the catalyst content, the reaction temperature, the molar ratio of alcohol to oil and the water content. High methyl ester yield and fast reaction rate could be obtained even if the reaction pressure was relatively low. In addition, kinetics of the transesterification reaction was also discussed.     

Conversion of biomass to fuel: Transesterification of vegetable oil to biodiesel using KF loaded nano-γ-Al2O3 as catalyst

KF-impregnated nanoparticles of γ-Al₂O₃ were calcinated and used as heterogeneous catalysts for the transesterification of vegetable oil with methanol for the synthesis of biodiesel (fatty acid methyl esters, FAME). The ratio of KF to nano-γ-Al₂O₃, calcination temperature, molar ratio of methanol/oil, transesterification reaction temperature and time, and the concentration of the catalyst were used as the parameters of the study. A methyl ester yield of 97.7 ± 2.14% was obtained under the catalyst preparation and transesterification conditions of KF loading of 15 wt%, calcination temperature of 773 K, 8 h of reaction time at 338 K, and using 3 wt% catalysts and molar ratio of methanol/oil of 15:1. This relatively high conversion of vegetable oil to biodiesel is considered to be associated with the achieved relatively high basicity of the catalyst surface (1.68 mmol/g) and the high surface to volume ratio of the nanoparticles of γ-Al₂O₃.     

生物柴油的制备及其副产物粗甘油分离与精制工艺的研究

研究了生物柴油制备工艺条件的确定及其副产品粗甘油的分离与精制,对甘油精制中溶剂的选择、溶液的pH值和蒸馏温度对甘油得率的影响进行了研究。制备生物柴油的最佳条件为醇油摩尔比6:1,催化剂用量1%,反应温度60℃,反应时间90 m in,得率达到98.1%(以菜籽油质量100 g为基准)。粗甘油精制的最佳工艺为:用甲醇作溶剂,离心溶液的pH值在5~7之间,在此条件下甘油的得率可以达到31.2%(以粗甘油质量为基准,100 g菜籽油得16 g粗甘油),纯度达到97.52%,可以满足于各种化工生产。     

Metakaolinite as a catalyst for biodiesel production from waste cooking oil

The use of metakaolinite as a catalyst in the transesterification reaction of waste cooking oil with methanol to obtain fatty acid methyl esters (biodiesel) was studied. Kaolinite was thermally activated by dehydroxylation to obtain the metakaolinite phase. Metakaolinite samples were characterized using X-ray diffraction, N₂ adsorption-desorption, simultaneous thermo-gravimetric analyse/differential scanning calorimetry (TGA/DSC) experiments on the thermal decomposition of kaolinite and Fourier-transform infrared spectrometer (FTIR) analysis. Parameters related to the transesterification reaction, including temperature, time, the amount of catalyst and the molar ratio of waste cooking oil to methanol, were also investigated. The transesterification reaction produced biodiesel in a maximum yield of 95% under the following conditions: metakaolinite, 5 wt-% (relative to oil); molar ratio of oil to methanol, 1∶23; reaction temperature, 160°C; reaction time, 4 h. After eight consecutive reaction cycles, the metakaolinite can be recovered and reused after being washed and dried. The biodiesel thus obtained exhibited a viscosity of 5.4?mm²?s^–1 and a density of 900.1 kg?m^–3. The results showed that metakaolinite is a prominent, inexpensive, reusable and thermally stable catalyst for the transesterification of waste cooking oil.