Gas holdup in a gassed reciprocating plate column with rashig rings placed in interplate spaces

The gas holdup is studies in a gassed reciprocating plate column with the addition of the Rashig rings placed in each interplate space. The gas holdup generally increases with increasing the vibration speed, the superficial gas velocity, and the solids concentration in the range of operating conditions applied. Independently of the solids concentration, the gas holdup is correlated with the power consumption and the superficial gas velocity. The Rashig rings are shown to have more effective dispersion action than the polypropylene spheres under the same other operating conditions.     

Experimental Study on the Hydrodynamics and Mass Transfer Characteristics of Ultrasonic Loop Airlift Reactor

The promoting effect of ultrasonic wave on the hydrodynamics and mass transfer characteristics of the loop airlift reactor was studied. The gas holdup, liquid circulation velocity, mixing time and overall volumetric mass transfer coefficient were examined and compared, with and without ultrasonic wave in the reactor. The experimental results show that ultrasound has almost no notable effect on the gas holdup, but has a tendency to decrease gradually the liquid circulation velocity and increase the overall volumetric mass transfer coefficient; and the effect on the mixing time is relatively complex. At low superficial gas velocity, the low powered ultrasound promotes the radial mixing of fluid; with the ultrasonic power increasing, ultrasonic vibration obstructs the axial mixing of fluid. Moreover, the effect of ultrasonic wave on the mixing time gradually decreases with the increase in the superficial gas velocity. Therefore there exists an optimal ultrasonic power for hydrodynamics and mass transfer. Correlations were also proposed for the hydrodynamics and mass transfer characteristics of the reactor.     

Time-dependent gas holdup variation in an air-water bubble column

Time-dependent gas holdup variation in a two-phase bubble column is reported with air and tap water as the working fluids. The results indicate that time-dependent gas holdup is closely related to the water, whose quality is unsteady and changes, not only during the two-phase flow, but also during idle periods. The significance and characteristics of the time-dependent gas holdup variation are influenced by the bubble column operation mode (cocurrent or semi-batch), the sparger orientation, the superficial gas velocity, and the superficial liquid velocity. It is proposed that a volatile substance (VS), which exists in the water in very small concentrations and inhibits bubble coalescence, evaporates during column operation and results in a time-dependent gas holdup. The influence of bubble column operation mode, sparger orientation, superficial gas velocity, and superficial liquid velocity on the time-dependent gas holdup variation are explained based on their effects on bubble size, bubble contacting frequency and mixing intensity. This work reveals that regular tap water may cause significant reproducibility problems in experimental studies of air-water two-phase flows.     

滴流床反应器内脉冲流下动持液量实验

对气液强相互作用下滴流床反应器内的流体动力学进行了分析讨论 .实验测定了脉冲流流型下的床层平均动持液量 .考察了气液流率、液体黏度、填料材料等因素对动持液量的影响 .根据对滴流床反应器内流体流动机理的分析及实验结果 ,提出了关联脉冲流型式下动持液量的关联式 .该关联式能很好地关联实验数据 ,可用于预测温和型脉冲流下的动持液量     

高长径比三相内环流反应器中细颗粒相含率和循环液速的分布研究

在高径比为22的三相内环流反应器中,在常温常压下以空气-水-石英砂为物系,研究了在不同粒径下上升区固含率、下降区固含率和上升区循环液速随表观气速的变化规律和不同粒径下轴向固含率的分布情况,以及在固体体积分数不同的条件下,平均气含率和上升区气含率随表观气速的变化情况。结果表明:当粒径(ds)≤0.3 mm时,上升区固含率随表观气速的增加呈平缓变化趋势,下降区固含率随表观气速的增加而增加;当0.3 mm相似文献   

Hydrodynamics of a slurry airlift reactor at high solid concentrations

The hydrodynamics of a slurry airlift reactor at high solid concentrations were experimentally studied. The influences of the average solid concentration, superficial gas velocity and particle size on the radial and axial profiles of the solid holdup, average gas holdup and liquid circulation velocity were investigated. The local solid holdup was measured with an electrical conductivity probe. At low solid concentrations or high superficial gas velocities, the radial profile of the solid holdup was uniform. At high solid concentrations, the radial profile of the solid holdup was nonuniform, with higher values near the wall. This radial nonuniformity increased with decreased superficial gas velocity or increased average solid concentration. The axial profile of the cross-sectional average solid holdup was uniform at all conditions in this work, even at high solid concentrations. The average gas holdup and liquid circulation velocity increased with the superficial gas velocity but decreased with the average solid concentration. A mathematical model based on the balance of the transverse lift force and turbulent dispersion force was proposed to predict the radial profile of the solid holdup. Reasonable predictions were obtained from this model with an adjustable model parameter.     

Influence of impeller diameter on overall gas dispersion properties in a sparged multi-impeller stirred tank☆

The impeller configuration with a six parabolic blade disk turbine below two down-pumping hydrofoil propellers, identified as PDT + 2CBY, was used in this study. The effect of the impeller diameter D, ranging from 0.30T to 0.40T (T as the tank diameter), on gas dispersion in a stirred tank of 0.48 m diameter was investigated by experimental and CFD simulation methods. Power consumption and total gas holdup were measured for the same impeller configuration PDT + 2CBY with four different D/T. Results show that with D/T increases from 0.30 to 0.40, the relative power demand (RPD) in a gas–liquid system decreases slightly. At low superficial gas velocity V_S of 0.0078 m·s^-1, the gas holdup increases evidently with the increase of D/T. However, at high superficial gas velocity, the systemwith D/T=0.33 gets a good balance between the gas recirculation and liquid shearing rate, which resulted in the highest gas holdup among four different D/T. CFD simulation based on the two-fluid model along with the Population Balance Model (PBM) was used to investigate the effect of impeller diameter on the gas dispersion. The power consumption and total gas holdup predicted by CFD simulation were in reasonable agreement with the experimental data.     

Power consumption and mass transfer in agitated gas-liquid columns: A comparative study

Power consumption, gas holdup and oxygen mass transfer in agitated gas-liquid columns have been studied for an air-water system. Measurements have been carried out in a reciprocating plate reactor using five different types of perforated plates and in a stirred tank reactor with one, two and three Rushton turbines, a helical ribbon impeller with and without surface baffles. Each mixing vessel had an identical geometry with a working volume of 17 L. For reciprocating plate stacks, the gas holdup is a complex function of the perforation diameter, the frequency of agitation and the gas superficial velocity. For radial-type mixing devices, the gas holdup increases more rapidly with the speed of rotation for the helical ribbon. The power imparted to the fluid by the mixing device is independent of the gas superficial velocity for the plate stacks and the helical ribbon impeller for a given frequency or speed of agitation whereas it decreases for Rushton turbines. The correlation of the power consumption obtained for all mixing devices plotted against the reciprocating frequency or speed of rotation to the third power shows a linear fit. K_La values were correlated very well with the power input per unit volume and superficial gas velocity for all mixing devices. At lower power input per unit volume, K_La is a function of only the gas superficial velocity. At higher input power per unit volume, K_La increases rapidly with an increase in the intensity of agitation. Reciprocating plates with larger diameter perforations led to higher K_La values whereas the lowest K_La were obtained with the helical ribbon impeller. Correlations for one and three Rushton impeller assemblies were almost identical whereas measured K_La were much higher for the two-impeller assembly due to the presence of a highly mixed zone in the vicinity of the dissolved oxygen probe.     

强制液体外循环气升式内环流反应器的流体力学特性

在有机玻璃制成的主体反应器(φ0.286 m×3.0 m)内,采用空气-水的气液两相体系考察了不同表观气速下带有中心下料管和环管式气体分布器的环流反应器内局部气含率和内环气泡上升速度的流体力学特性。结果表明：气含率均随表观气速的增大而增大;从外环流入内环的气泡数量比较少;在相同条件下外环的气含率远远低于内环的气含率;新型气体分布器的采用和液体外循环的引入可以增大床层气含率并使其分布趋于均匀,从而增大了内环中气液两相的接触面积和湍动强度,使传递过程得到强化。在此基础上采用商业软件ANSYS CFX10.0对该反应器进行了数值模拟研究,模拟结果与实验数据基本吻合,说明了基于实验验证的Euler-Euler法可以用于该反应器开发和放大研究。     

水平管段塞流持液率的波动特性

气液两相段塞流是液塞和长气泡在空间和时间上的交替,在流动过程中表现出间歇性和不稳定性.今对水平管中段塞流持液率的波动特性进行了分析.结果表明:在同一折算液速下,随着折算气速的增加,段塞单元的平均持液率和液膜持液率先快速下降再缓慢下降,而液塞持液率先缓慢下降再快速下降.段塞流持液率的概率密度分布为双峰分布,高持液率峰对应于液塞区,低持液率峰对应于液膜区;概率密度函数中较完好的峰所对应的持液率与光滑分层液膜区和液塞区的平均持液率相一致.     

剪切变稀体系同心双轴搅拌釜内的气液分散模拟

气液搅拌设备因其良好的适用性被广泛应用于过程工业中。为更好地比较不同工况下剪切变稀体系中的气液分散情况,通过实验研究整体气含率和相对功耗确定适宜的转动模式,进而模拟研究表观气速、体系黏度、搅拌转速对气含率和气泡尺寸的影响。结果表明,相同功率下内外双桨反向旋转模式在理想气液分散条件下,相较于单轴内桨和内外双桨同向旋转模式具有更高的气含率和更好的气体泵送能力;表观气速的增加有利于气泡的均匀分散,但气泡尺寸也会随之增大;有效黏度的增加使得搅拌桨的影响区域变小,不利于气泡的均匀分散,气泡尺寸也随之增大;搅拌转速的增加使得循环涡流的影响区域变大,高气含率区不断扩大。     

Hydrodynemics of a cocurrent upflow liquid–liquid reciprocating plate reactor for homogeneously base-catalyzed methanolysis of vegetable oils

Hydrodynamics of a continuous cocurrent two-phase upflow reciprocating plate reactor (RPR) for homogeneously base-catalyzed methanolysis of sunflower oil was studied. Here, methanol constituted the dispersed phase and sunflower oil was the continuous phase. The measurements were performed in both the non-reactive (methanol–sunflower oil) and reactive (sunflower oil–methanol–KOH) systems. The main goal was to define the effects of the vibration intensity and the important reaction operating conditions on the pressure fluctuation at the reactor bottom, the power consumption, the dispersed phase holdup, the Sauter-mean drop diameter and the specific interfacial area. The power consumption under batch, single- and two-phase flow was proved to depend on the vibration intensity. The Sauter-mean drop diameter was found to depend on the specific power consumption in accordance with the turbulent model due to the turbulent energy dissipation in well-mixed regions around perforated plates. The simplified correlation of Kumar and Hartland could be used for estimating the Sauter-mean drop diameter. The energy dissipation due to reciprocating plate motion and the superficial dispersed phase velocity affected the dispersed phase holdup and the specific interfacial area. The present results are crucial for designing RPRs for application in continuous base-catalyzed methanolysis of vegetable oils.     

Experimental analysis and development of correlations for gas holdup in high pressure slurry co-current bubble columns

The effect of liquid and gas velocities, solid concentrations, and operating pressure has been studied experimentally in a 15 cm diameter air-water-glass beads bubble column. The superficial gas and liquid velocities varied from 1.0 to 40.00 cm/s and 0 to 16.04 cm/s, respectively, while the solid loading varied from 1 to 9%. The gas holdup in the column was reduced sharply as we switched from batch to co-current mode of operation. At low gas velocity, the effect of liquid velocity was insignificant; while at high gas velocity, increasing liquid velocity decreased the gas holdup. Drift flux approach was applied to quantify the combined effect of liquid and gas velocities over gas holdup. For co-current three phase flows, the gas holdup decreased with increase in solid loading for all pressures. But for batch operations, when solid loading was 5% or more, settling started leading to higher gas holdup. Increasing pressure from atmospheric conditions increased the gas holdup significantly, flattening asymptotically.     

气升式外环流反应器的体积传质系数

以Higbie的渗透理论和Kolmogoroff的湍流理论为基础,提出了计算液体旋涡在气液相界面暴露时间的方法,并建立了预测体积传质系数的模型方程。在不同管径比下的外环流反应器中,对空气 水体系测定了操作气速对体积传质系数、循环液速和气含率的影响。将体积传质系数与表观气速和下降管与上升管的面积比按幂函数进行关联,其预测值和试验值符合较好。     

气升式内环流反应器内局部气含率径向分布

The local gas holdup profiles in an internal-loop airlift reactor were studied experimentally by using dual electrical conductivity probe under different conditions,including superficial velocity,surface tension and liquid viscosity.The results showed that the radial gas holdup profile has a parabolic shape,which was consistent with the empirical model of Luo.Local gas holdup distribution parameters were obviously influenced by flow regime and almost remained unchanged in the same flow regime.In the gas distributor region,the profiles were steeper in the homogenous flow regime than in the heterogeneous flow regime.However,in the stable region,there was an inverse change trend in two flow regimes.The increase of surface tension,superficial velocity and liquid viscosity made the profile of local gas holdup steeper in two flow regimes.     

多室气升式环流反应器流动特性的数值模拟

在空气-水两相多室气升式环流反应器（MALR）中,采用欧拉欧拉两相流模型对扇形反应室内气液两相流动过程进行了数值模拟研究,考察了上升室的气含率、液体速度随表观气速的变化,最后用实验数据对模拟结果进行了验证.结果表明,某一上升室气含率受该室表观气速的影响较大,与另一上升室表观气速的影响较小;循环液体与上升室流体流动型式有关;气含率和循环液速的模拟值与实验值的平均相对误差分别为5.36％和8.28％;说明了应用数值模拟方法研究MALR流动特性的可行性.     

The measurement of bubble diameter distributions and liquid side mass transfer coefficients in a gas-liquid agitated vessel using a real-time,high-speed image processing system

In this study, we report the measurement results of various spatial distributions, such as Sauter diameter, gas holdup ratio, and interface area per unit liquid volume, in a vessel using a real-time, high-speed image processing system developed by ourselves. We attempted to separate liquid side mass transfer coefficients, k L , from overall volumetric mass transfer coefficients, k L a, based on the results mentioned above. And we examined the relations between power consumption per unit volume, P v , and both k L and k L a in order to establish correlation equations of k L and k L a with P v , gas holdup ratio, gas superficial velocity, v s , and surface tension.     

Effects of internals on phase holdup and backmixing in a slightlyexpanded-bed reactor with gas-liquid concurrent upflow

Five different internals were designed, and their effects on phase holdup and backmixing were investigated in a gas-liquid concurrent upflow reactor where the spherical alumina packing particles of three diameters (3.0, 4.5 and 6.0 mm) were slightly expanded under the conditions of varied superficial gas velocities (6.77×10^-2-3.61×10^-1 m·s^-1) and superficial liquid velocities (9.47×10^-4-2.17×10^-3 m·s^-1). The experimental results show that the gas holdup increases with the superficial gas velocity and particle size, opposite to the variational trend of liquid holdup. When an internal component is installed amid the upflow reactor, a higher gas holdup, a less liquid holdup and a larger Peclet number characterizing the weaker backmixing are obtained compared to those in the bed without internals under the same operating conditions. Additionally, the minimal backmixing is observed in the reactor equipped with the internals with a novel multi-step design. Finally, empirical correlations were proposed for estimating gas holdup, liquid holdup and Peclet number with the relative deviations within 11%, 12% and 25%, respectively.     

THE MEASUREMENT OF BUBBLE DIAMETER DISTRIBUTIONS AND LIQUID SIDE MASS TRANSFER COEFFICIENTS IN A GAS-LIQUID AGITATED VESSEL USING A REAL-TIME,HIGH-SPEED IMAGE PROCESSING SYSTEM

In this study, we report the measurement results of various spatial distributions, such as Sauter diameter, gas holdup ratio, and interface area per unit liquid volume, in a vessel using a real-time, high-speed image processing system developed by ourselves. We attempted to separate liquid side mass transfer coefficients, k L , from overall volumetric mass transfer coefficients, k L a, based on the results mentioned above. And we examined the relations between power consumption per unit volume, P v , and both k L and k L a in order to establish correlation equations of k L and k L a with P v , gas holdup ratio, gas superficial velocity, v s , and surface tension.     

三相环流反应器流体力学行为

气升式三相环流反应器综合了鼓泡塔和机械搅拌釜的优良性能,具有结构简单、无机械传动部件、易密封、造价低、容易实现工业放大等优点,在石油、化工、电化学和生物化工等领域得到了广泛应用．随着能源形势的日趋紧张,环流反应器在液相法合成甲醇、浆态床一步法合成二甲醚、煤液化等过程中的应用得到许多研究人员的重视,并取得了重要的研究进展．由于目前对其内部流动行为尚缺乏系统的认识,进行工业设计和操作过程中仍显理论指导不足