Structure and Properties of Compatible PPSF‐Rich Blends with PET

Summary: New PPSF/PET (poly(phenyl sulfone)/poly(ethylene terephthalate)) blends rich in PPSF were obtained by direct injection molding. Biphasic morphologies with a very large interface area/dispersed phase volume ratio were obtained and were attributed to a low interfacial tension in the melt state, a consequence of the reactions observed between the components of the blends. This favorable morphology led to small strain mechanical properties close or slightly above those predicted by the direct rule of mixtures, and more significantly, to elongations at break of the blends higher than that of the PPSF matrix.

Morphology of the cryogenically‐broken etched surface of a PPSF/PET 75/25 blend.     

Preparation of Poly(ethylene terephthalate)/Poly(amino ether) Blends by means of the Addition of Poly(butylene terephthalate)

Summary: Blends based on poly(ethylene terephthalate), PET, with poly(amino ether) (PAE) contents up to 40% were obtained by the addition of 20% poly(butylene terephthalate) (PBT) to the PET matrix. PBT mixed with PET led to a decrease in the T_m of the matrix that was enough to produce homogeneous blends by mixing in the melt state. Despite the presence of a single peak observed by dynamic‐mechanical analysis, the blends were biphasic, with amorphous phases in which minor amounts of the other component, both reacted and mixed, were present. This presence of minor components gave a fine morphology and significant adhesion that, together with the higher orientation of PAE in the blends, produced blends with a clear synergism in the modulus of elasticity, notched impact strength similar to that of the neat components, and high ductility up to 30% PAE.

Young's modulus of the PET‐PBT/PAE blends.     

The Effect of Particle Matrix Adhesion on the Mechanical Properties of Silica Filled Cyanate Ester Composites

Summary: The effect of silica and its surface treatment on the mechanical properties of composites was studied as part of the evaluation of cyanate ester matrices as potential electronic encapsulants. Three filler surface treatments were used, as a qualitative interfacial adhesion scale, in an attempt to gauge the magnitude of interfacial adhesion between untreated filler and the cyanate ester matrix. There was strong interfacial adhesion between matrix and untreated filler. The level of silica content most affected composite modulus and fracture toughness. Filler surface treatment most affected composite strength and fracture toughness/energy. Composite fracture was found to occur via crack pinning and/or crack blunting depending on the strength of adhesion. The composites evaluated were found to possess suitable mechanical properties for potential use as electronic encapsulants.

     

Biocomposites Made from Short Abaca Fiber and Biodegradable Polyesters

Natural fiber‐reinforced biodegradable polyester composites were prepared from biodegradable polyesters and surface‐untreated or ‐treated abaca fibers (length ca. 5 mm) by melt mixing and subsequent injection molding. Poly(butylene succinate)(PBS), polyestercarbonate (PEC)/poly(lactic acid)(PLA) blend, and PLA were used as biodegradable polyesters. Esterifications using acetic anhydride and butyric anhydride, alkali treatment, and cyanoethylation were performed as surface treatments on the fiber. The flexural moduli of all the fiber‐reinforced composites increased with fiber content. The effect of the surface treatment on the flexural modulus of the fiber‐reinforced composites was not so pronounced. The flexural strength of PBS composites increased with fiber content, and esterification of the fiber by butyric anhydride gave the best result. For the PEC/PLA composites, flexural strength increased slightly with increased fiber content (0–20 wt.‐%) in the case of using untreated fiber, while it increased considerably in the case of using the fiber esterified by butyric anhydride. For the PLA composite, flexural strength did not increase with the fiber reinforcement. The result of soil‐burial tests showed that the composites using untreated fiber have a higher weight loss than both the neat resin and the composites made using acetylated fiber.

Flexural modulus of PBS composites as a function of fiber content.     

Properties of Poly(3‐hydroxybutyric acid) Composites with Flax Fibres Modified by Plasticiser Absorption

Natural fibre‐biopolymer composites have been prepared from flax and polyhydroxybutyrate (PHB). The flax was modified by drying, followed by plasticiser absorption to replace the water lost to prevent embrittlement. This protects the fibres from problems associated with their water content and changes in water content due to equilibration with the environment. Flax and PHB showed good interfacial adhesion, which was decreased when plasticisers were present. Some plasticiser migrated from the flax to PHB and caused complex changes in the glass transition, crystallisation and crystallinity of the PHB. Morphology of the composites was examined by scanning electron microscopy (SEM) and optical microscopy (OM), SEM provided information on the interfacial adhesion through fractography. OM showed extensive transcrystallinity along the fibre surfaces. Dynamic mechanical analysis was used to measure elastic and damping characteristics and their relation to composition and morphology.

SEM micrograph of the PHB‐plasticiser‐flax system PHB‐PEG‐flax.     

Molecular and Morphological Characterization of Immiscible SAN/EPDM Blends Filled by Nano Filler

The compatibilizing effect of nano sized calcium carbonate filler on immiscible blends of styrene‐co‐acrylonitrile/ethylene propylene diene (SAN/EPDM) was examined. The surface energy of the calcium carbonate was modified by stearic acid. The compatibility of SAN/EPDM blends was studied by following the glass transition temperature T_g by DSC. SEM was used to observe the blend morphology and the X‐ray analyzer was used to detect the calcium from filler in samples. Mechanical properties of the blends were determined, and related to changes of polymer‐filler interactions and morphology. The results suggest that the morphology of the SAN/EPDM blends studied was affected by the reduction of surface energy of the filler.

SEM micrograph of an SAN/EPDM blend with 5% of maximally treated filler.     

Morphology and Mechanical Properties in Polymer Blends of Photocurable Polymer and Polycarbonate

Relationships between the morphologies and mechanical properties of binary blends of a photocurable polymer (2‐propenoic acid, (octahydro‐4,7‐methano‐1H‐indenediyl) bis(methylene)ester; DCA) and a linear polymer (poly(4,4′‐cyclohexylidene bisphenol carbonate); PCz) have been investigated. The blend films are prepared by in situ photopolymerization of homogeneous mixtures of a DCA‐monomer and PCz. The phase structure has been converted from a semi‐interpenetrating polymer networks (semi‐IPN) structure to a bicontinuous structure by controlling the cure temperature. Bicontinuous phase‐separated structures can be obtained by curing a wide range of compositions of 17–50 wt.‐% PCz at high temperatures. Miscible semi‐IPN structures are attained by means of photopolymerization below the glass transition temperature of the homogenous mixture before performing photoirradiation, such that magnetic relaxation measurements showed the blend to be miscible in the 10 nm order. The tensile strength and modulus reached a maximum in those blends having an intermediate vague phase structure between semi‐IPN and bicontinuous structures that have a strong interfacial interaction, which leads to incomplete phase decomposition in the PCz‐rich matrix phase. The maximum strength and modulus prepared under optimum condition are inferior to those of the individual components. In contrast, the elongation and break energy are greatly improved in those blends with bicontinuous structures having a diffused phase boundary.

DCA‐rich domain size in bicontinuous structure for DCA/PCz system, as a function of cure temperature; (□) 17 wt.‐% PCz, (○) 30 wt.‐% PCz, and (?) 50 wt.‐% PCz.     

Viscoelasticity in Polymer Films on Rigid Substrates

The viscoelasticity of two thermally crosslinked polymer coatings was examined in terms of relaxation of the applied stress after a sudden strain. Two different transient methods were utilized: flat‐ended cylindrical indentation testing of a polymer film on a rigid substrate and tensile testing of a corresponding free‐standing polymer film. The correlation between tensile and indentation tests was studied. The mechanical response of a viscoelastic layer deposited on a rigid substrate was investigated as a function of indentation depth. There was good agreement between the results of the tensile and indentation tests for thick film layers at moderate indentation depths. The findings indicate that the substrate influences the coating performance by reducing the viscous contribution to the stress response and amplifying the magnitude of the equilibrium modulus for large indentation depths. The indentation method utilized here was shown to be a potentially suitable tool for the determination of Poisson's ratio of polymer films.

     

Influence of Different Woven Geometry in Poly(propylene) Woven Composites

Summary: The difference between the melting temperatures of poly(propylene) (PP) fibre and random poly(propylene‐co‐ethylene) (PPE) was exploited in order to establish processing conditions for an all PP composite. Under these conditions the matrix must be a liquid in order to ensure good wetting and impregnation at the fibres, though the temperature must not be too high to avoid melting the fibres. The high chemical compatibility of the two components allowed creation of strong physico‐chemical interactions, which favour strong interfacial adhesion. The static and dynamic mechanical properties and morphology of poly(propylene) woven fabric reinforced random PPE composites have been investigated with reference to the woven geometry that influenced the properties of the woven composites. Among the various cloth architectures that were used in the PP‐PPE composites, the satin weave imparted overall excellent mechanical properties due to the weave parameters, such as high float length and fibre count, low interlace point and crimp angle, etc. Morphology of the composite has been investigated by macro photography and scanning electron microscopy. Images from scanning electron microscopy provided confirmation of the above results by displaying the consolidation and good fibre‐matrix wetting of the composites.

Loss modulus of poly(propylene) woven‐matrix composites with different types of woven geometry.     

Structural and Mechanical Properties Changes of Ethylene‐α‐olefin Copolymer Blends Induced by Thermal Treatments and Composition

Summary: Blends of single‐site catalysed ethylene‐α‐butene (C₄VLDPE) and ethylene‐α‐octene (C₈VLDPE) copolymers were prepared by melt extrusion. The phase morphology, thermal and mechanical properties of the blends have been investigated by differential scanning calorimetry (DSC), scanning electron microscopy (SEM), tensile test and dynamic mechanical analysis (DMA). Depending on the composition and thermal history, significant differences in structure and behaviour were found. It was also found that some degree of co‐crystallization occurred for quenched blends; whereas most of the oven slowly cooled blends showed two well‐defined melting peaks, indicating that the slow cooling favoured partial segregation of the fractions with different degrees of branching to form two morphologies. Moreover, SEM revealed morphology of the thinner crystals distributed in‐between the thicker sheaf‐like crystals for the slowly cooled blends with 20–50% C₈VLDPE. Therefore, the synergism in mechanical properties for the blends with 20–50% C₈VLDPE is due to a combination of larger crystal size, more complete phase separation and interfacial interaction produced by the segregation effect of the slow cooling treatment. DMA studies showed that the storage modulus increased as the addition of C₈VLDPE and modulus for the slowly cooled blends are about twice those measured for the quenched ones, indicating higher stiffness of the blends. The smooth shift of β relaxation temperature with addition of C₈VLDPE for both sets of blends confirmed the miscibility in the amorphous phase.

SEM image of the C₄VLDPE‐C₈VLDPE (50/50) blend after oven slow cooling treatment.     

Modification of Rheological Properties Under Elongational Flow by Addition of Polymeric Fine Fibers

A new technique to provide melt elasticity using flexible fine fibers prepared from a polymer with high melting point is demonstrated. A polymer composite of poly(propylene) with a small amount of fine fibers of poly(butylene terephthalate) shows marked strain‐hardening behavior in elongational viscosity, i.e., a rapid increase in the transient elongational viscosity with time or strain. The blend also shows prominent normal stress difference at steady shear. These elastic properties have not been observed for polymer composites with rigid fibers and can be applicable to the modification of rheological properties and thus the improvement of processability.

     

Lignocellulosic Flour from Cladodes of Opuntia ficus‐indica Reinforced Poly(propylene) Composites

Summary: A lignocellulosic flour was obtained by grinding dried cladodes of Opuntia ficus‐indica. It was used as low cost natural filler in PP and the effect of the treatment of the filler with MAPP was also investigated. The morphology and thermal properties of these composites were evaluated by SEM and DSC, respectively. MAPP coating resulted in a better adhesion between the filler and the matrix and higher homogeneity of the material. A decrease of the degree of crystallinity of the PP matrix in presence of the untreated filler was observed. Dynamic mechanical analysis and tensile properties were also studied. High‐strain tensile properties display enhanced mechanical properties for MAPP treated‐based composites only. When conditioned in highly moist atmosphere (98% RH), both the water uptake and water diffusion coefficient decrease when the filler was treated. These effects were ascribed to the promoting interfacial adhesion induced by the coating treatment. In liquid water, this increased adhesion between the filler and the matrix results in a higher weight loss of the material. It is due to the removal of the grafted polymer from the material during the dissolution of part of the filler.

SEMs of freshly fractured surface for a PP film filled with 10 wt.‐% of MAPP treated OFI cladode (top) and calcium oxalate crystallite within the PP matrix for a 3 wt.‐% filled composite (bottom).     

Poly(acrylonitrile‐butadiene‐styrene)/Poly(ether ether ketone) Blends: an Attempt Towards a Polymer Reinforced Polymer Composite

Summary: Blends of poly(acrylonitrile‐butadiene‐styrene) (ABS) and poly(ether ether ketone) (PEEK), in which PEEK has been used as a reinforcing medium for the ABS matrix in ratios up to 20 wt.‐% of the blend, were prepared by melt mixing using a laboratory mixer. All the blend compositions were processed at the ABS processing temperature so that the PEEK was dispersed in the ABS matrix without actually melting. Differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) studies revealed that the glass transition temperature (T_g) of the ABS phase in the blend did not show any appreciable change with composition. The dynamic storage modulus measured by DMA was found to be higher for the blend as compared to pure ABS due to reinforcement of the matrix by PEEK. The tensile strength and modulus behavior of these blends were found to follow the curves predicted using models proposed for composite systems having perfect adhesion, which shows the presence of some physical interaction between the blend components. The good tensile properties of the blend have been correlated with the observed morphology. The disperse phase in the blend has been found to be present in extremely small (sub‐micron) dimensions, which not only provides more surface area for possible interactions between the blend components but also result in efficient stress transfer between the matrix and the dispersed phase during the tensile tests. The thermal stability of the blends was investigated using thermogravimetric analysis (TGA). TGA further revealed that the constituents degraded at their respective decomposition temperatures.

SEM micrograph of tensile fractured surface of an ABS/PEEK 90/10 blend.     

Morphology,Thermal and Mechanical Properties of Poly(propylene) Fibre‐Matrix Composites

Preparation and properties of poly(propylene)‐poly(propylene) composites have been investigated. Poly(propylene) fibres of varying diameter have been incorporated in a random ethylene co‐poly(propylene). The composites prepared from the same semi‐crystalline polymer in the matrix and reinforcement have lead to inherently strong interfacial bonding between the two phases of the same polymer. The composites demonstrated enhanced stiffness, which increased with fibre diameter. The structure, thermal, static and mechanical properties of poly(propylene) long fibre reinforced random co‐poly(propylene) composites have been studied with reference to the fibre diameter. The matrix and fibre components retained their separate melting temperatures. After melting, the two phases remained separate and showed their individual crystallization temperatures on cooling, and melting temperatures on a second heating. The melting temperature of the poly(propylene) fibres increased after formation of the composites. The compression molding of the composites at a temperature below the melting temperature of the fibres caused annealing of the fibre crystals. By incorporation of long poly(propylene) fibre into random co‐poly(propylene), the glass transition, storage and static modulus have been found to be increasing and composite with the largest fibre diameter shows better properties. Transcrystallization of the matrix poly(propylene) was observed.

Optical microscopy of composites with fibre diameter 68 μm.     

Supertoughness in Polysulfone/Poly(ethylene‐octene) Blends

Summary: Poly(sulfone of Bisphenol A) (PSU) based blends were obtained by melt blending PSU with up to 15 wt.‐% poly(ethylene‐octene) either modified with maleic anhydride (mPEO) or not (PEO). The dispersed particle size was small and similar in blends with PEO or mPEO. These facts indicated respectively that the interfacial tension was low and the lack of compatibilizing effect of mPEO. Some preferential presence of PEO in the outer surface of the specimens was observed, and was attributed to the large viscosity difference between the two components of the blends. This had no effect on the modulus of elasticity, but speeded up both the yield stress and ductility decreases at rubber contents above 3.25 wt.‐%. However, despite the immiscibility of the components, and thanks to the small particle size of the blends, super‐toughness was attained in the unmodified PSU/PEO blends. This was at PEO contents (3.25 wt.‐%) at which the modulus, yield stress and ductility of the blends were almost as good as those of pure PSU. It appeared that a change of the chemical nature of the rubber did not influence by itself super‐toughness, unless it was accompanied by either a morphological or adhesion change.

Impact strength of PSU‐based blends vs. PEO (○) or mPEO (?) content.     

Non‐Linear Long‐Term Tensile Creep of Poly(propylene)/Cycloolefin Copolymer Blends with Fibrous Structure

The tensile deformation of materials with Poisson's ratio smaller than 0.5 generates an additional free volume, which means that tensile creep under constant stress and temperature is a non‐iso‐free volume process. Fractional free volume rising proportionally to the creep strain accounts for a continuous shortening of retardation times. To account for this effect, “internal” time has been introduced which is related to a hypothetical pseudo iso‐free‐volume state. The shift factor along the time scale in the time‐strain superposition is not constant for an isothermal creep curve, but rises monotonically from point to point with the elapsed creep time. The reconstructed compliance dependencies obtained for various stresses approximately obey the time‐strain superposition thus forming a generalised creep curve. A routinely used empirical equation has been found suitable to describe the effects of time and stress on compliance of parent polymers and their blends. The previously proposed predictive format for the time‐dependent compliance of polymer blends has been found applicable also to poly(propylene) (PP)/cycloolefin copolymer (COC) blends with fibrous morphology. As COC shows a tendency to form fibres in a PP matrix, the mixing rule customarily used for fibre composites has been found more appropriate for injection moulded specimens than the equivalent box model for isotropic blends. The predicted compliance curve for a pseudo iso‐free‐volume state can be transformed into a “real” curve for a selected stress σ (in the interval up to the yield stress).

SEM microphotograph of the fractured surface (perpendicular to the injection direction) of the PP/COC blend 60/40.     

Novel Glass Fiber‐Reinforced Composites Having a UV and Peroxy Curable Fluoropolymer Matrix

Novel glass fiber‐reinforced composites were prepared from E‐glass fibers and perfluoropolyether (PFPE), polyurethane acrylate, and methacrylate resins. The PFPE resins were synthesized by a two‐step process and formulated with reactive acrylic diluents obtaining two compositions with different viscosity and fluorine content. These formulations were photocrosslinked by UV‐A radiation and characterized by tensile and dynamic‐mechanical properties as well as by impact resistance. The two UV cured fluoropolymer compositions are high modulus (> 1 GPa), polyphasic materials characterized by a fracture toughness higher than conventional polymer matrices, like epoxies and unsaturated polyesters. Unidirectional laminate composites were also prepared by hand lay‐up and crosslinked both photochemically and thermally. Mechanical characterization of glass fiber‐reinforced composites was carried out by tensile tests and shear adhesion measurements, showing a good fluoropolymer‐glass adhesion strength (ca. 9 MPa). Surface characterization of composites by static contact angle measurements allowed the calculation of the total surface tension γ_s according to Wu's harmonic mean approximation. Surface tension is very low (< 20 mN/m) suggesting a preferential stratification of PFPE segments at the material‐air interface.

     

Polyolefin/Lignosulfonate Blends, 9

Summary: In the present study, the compatibility, properties and degradability of polyolefin/lignin blends have been studied. Blends of three maleic anhydride grafted copolymers of ethylene‐propylene rubbers containing various content of functional groups with epoxy‐modified lignosulfonate have been investigated by microscopy, X‐ray diffraction, surface and mechanical indices determination, electron spin resonance, IR spectroscopy, differential scanning calorimetry and thermogravimetry. To assess the environmental degradation characteristics, the behavior of the blends during soil burial test has been investigated. The influence of the buried polymer blends on the physiological vegetative processes of the Vicia X Hybrida hort plant has been monitored.

Optical microscopy images of blend EP‐g‐MA 0.3/5 LER, undegraded (left) and degraded (right).     

Waste and Virgin LDPE/PET Blends Compatibilized with an Ethylene‐Butyl Acrylate‐Glycidyl Methacrylate (EBAGMA) Terpolymer, 1

Summary: This work is aimed at studying the morphology and the mechanical properties of blends of low density polyethylene (LDPE) and poly(ethylene terephthalate) (PET) (10, 20, and 30 wt.‐% of PET), obtained as both virgin polymers and urban plastic waste, and the effect of a terpolymer of ethylene‐butyl acrylate‐glycidyl methacrylate (EBAGMA) as a compatibilizer. LDPE and PET are blended in a single screw extruder twice; the first extrusion to homogenize the two components, and the second to improve the compatibilization degree when the EBAGMA terpolymer is applied. Scanning electron microscopy (SEM) analysis shows that the fractured surface of both the virgin polymer and the waste binary blends is characterized by a gross phase segregation morphology that leads to the formation of large PET aggregates (10–50 µm). Furthermore, a sharp decrease in the elongation at break and impact strength is observed, which denotes the brittleness of the binary blends. The addition of the EBAGMA terpolymer to the binary LDPE/PET blends reduces the size of the PET inclusions to 1–5 µm with a finer dispersion, as a result of an improvement of the interfacial adhesion strength between LDPE and PET. Consequently, increases of the tensile properties and impact strength are observed.

SEM micrographs of the fracture surface of a waste 70/30 LDPE/PET blend (R30) and of its blend with 15 pph of EBAGMA (R30C). Magnification × 1 000.     

Tensile Fracture and Failure Behavior of Thermoplastic Starch with Unidirectional and Cross‐Ply Flax Fiber Reinforcements

Thermoplastic starch (MaterBi®) based composites containing flax fibers in unidirectional and crossed‐ply arrangements were produced by hot pressing using the film stacking method. The flax content was varied in three steps, viz. 20, 40 and 60 wt.‐%. Static tensile mechanical properties (stiffness and strength) of the composites were determined on dumbbell specimens. During their loading the acoustic emission (AE) was recorded. Burst type AE signal characteristics (amplitude, width) were traced to the failure mechanisms and supported by fractographic inspection. The mechanical response and failure mode of the composites strongly depended on the flax content and the flax fiber lay‐up. It was established that the tensile strength increases until 40 wt.‐% flax fiber content but stays almost constant above this value. In the case of 40 wt.‐% unidirectional fiber reinforcement, the tensile strength of the composite was 3 times greater than that of the pure starch matrix. The flax fiber reinforcement increased the tensile modulus of the pure starch by several orders of amplitude.

SEM picture of the fracture surface of a composite with UD flax reinforcement.