Poly(ethylene terephtalate) films modified with N,N‐dimethylacrylamide: Incorporation of disperse dye

Poly(ethylene terephtalate), PET, can be modified with N,N‐dimethylacrylamide to obtain a better incorporation of disperse dye (Disperse Blue 79). Minimal variations in the decomposition at 10% level, melting, and glass transition temperatures, show that the thermal stability of modified PET films does not change when compared to nonmodified PET. The atomic force images show nanopeaks formation on the surface due to the modification. Modified PET films show a decrease in the contact angle and then, an increase in the superficial tension measurements, when compared to the value of 37 ± 1 dynes · cm⁻¹(nonmodified), with values liying in the range of 42–46 ± 0.5 dynes · cm⁻¹. The data obtained by photoacoustic spectroscopy (PAS) for dyed PET films show a dye peak at 580 nm. The data analysis of the peak area show that PET films modified with N,N‐dimethylacrylamide for 15 min at 85°C, dyed for 6 h at 85°C with a dye concentration of 0.333 g/L, incorporate three times more dye than the nonmodified films dyed in the same conditions. By the data obtained from PAS, it was possible to calculate the depth profile of dyeing with values around 54 μm. Factorial analyses show that the dyeing time was the most important variable. The major amount of incorporated dye was obtained by the following combination of variables: temperature and time of modifier treatment were, respectively, 72.5°C and 15 min; time and temperature of dyeing were, respectively, 90°C and 195 min for a dye concentration of 0.133 g/L. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 269–282, 2000     

Interpolymer‐specific interactions and miscibility in poly(styrene‐co‐acrylic acid)/poly(styrene‐co‐N,N‐dimethylacrylamide) blends

The miscibility or complexation of poly(styrene‐co‐acrylic acid) containing 27 mol % of acrylic acid (SAA‐27) and poly(styrene‐co‐N,N‐dimethylacrylamide) containing 17 or 32 mol % of N,N‐dimethylacrylamide (SAD‐17, SAD‐32) or poly(N,N‐dimethylacrylamide) (PDMA) were investigated by different techniques. The differential scanning calorimetry (DSC) analysis showed that a single glass‐transition temperature was observed for all the mixtures prepared from tetrahydrofuran (THF) or butan‐2‐one. This is an evidence of their miscibility or complexation over the entire composition range. As the content of the basic constituent increases as within SAA‐27/SAD‐32 and SAA‐27/PDMA, higher number of specific interpolymer interactins occurred and led to the formation of interpolymer complexes in butan‐2‐one. The qualitative Fourier transform infrared (FTIR) spectroscopy study carried out for SAA‐27/SAD‐17 blends revealed that hydrogen bonding occurred between the hydroxyl groups of SAA‐27 and the carbonyl amide of SAD‐17. Quantitative analysis carried out in the 160–210°C temperature range for the SAA‐27 copolymer and its blends of different ratios using the Painter–Coleman association model led to the estimation of the equilibrium constants K₂, K_A and the enthalpies of hydrogen bond formation. These blends are miscible even at 180°C as confirmed from the negative values of the total free energy of mixing ΔG_M over the entire blend composition. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1011–1024, 2007     

Kinetics of solvent responsiveness in poly(N,N‐dimethylacrylamide) hydrogels of different morphology

Crosslinked poly(N,N‐dimethylacrylamide) hydrogel samples were synthesized with various total comonomer concentrations and crosslinker ratios in the reacting mixture, and at two different temperatures: room temperature and the boiling point of the reacting mixture, about 80 °C. During gelation of samples prepared at the higher temperature, the bubbles of the boiling system were trapped in positions homogeneously distributed, and post‐gel reactions fixed them. These samples were macroporous, showing about three times the swelling capacity of conventional hydrogels synthesized at room temperature with the same composition. Both types of hydrogel swollen at equilibrium in water deswelled exponentially with time when they were immersed in acetone or dioxane. The rate of shrinking was higher for macroporous than for conventional samples and it was smaller in dioxane, the solvent with higher viscosity (η), although there was no proportionality to the solvent fluidity, η^?1. The morphology, which was in the scale of micrometres (as revealed by scanning electron microscopy), played a minor role in the shrinking rates of both types of gels. The excess swelling and the faster solvent response of macroporous gels were ascribed to the store and draining capacity of macropores at the millimetre scale. Copyright © 2005 Society of Chemical Industry     

Specific interactions in poly(styrene‐co‐2‐hydroxyethyl acrylate)/poly(styrene‐co‐N,N‐dimethylacrylamide) systems

Amphiphilic copolymers of poly(styrene‐co‐2‐hydroxyethyl acrylate) (SHEA) and poly(styrene‐co‐N, N‐dimethylacrylamide) (SAD) of different compositions were prepared by free radical copolymerization and characterized by different techniques. Depending on the nature of the solvent and the densities of interacting species incorporated within the polystyrene matrices, novel materials as blends or interpolymer complexes with properties different from those of their constituents were elaborated when these copolymers are mixed together. The specific interpolymer interactions of hydrogen bonding type and the phase behavior of the elaborated materials were investigated by differential scanning calorimetry (DSC) and Fourier transform infra red spectroscopy (FTIR). The specific interactions of hydrogen bonding type that occurred within the SHEA and within their blends with the SAD were evidenced by FTIR qualitatively by the appearance of a new band at 1626 cm^?1 and quantitatively using appropriate spectral curve fitting in the carbonyl and amide regions. The variation of the glass transition temperature with the blend composition behaved differently with the densities of interacting species. The thermal degradation behavior of the materials was studied by thermogravimetry. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

DNA adsorption on poly(N,N‐dimethylacrylamide)‐grafted chitosan hydrogels

In this study, poly(N,N‐dimethylacrylamide) grafted chitosan (PDMAAm‐g‐CT) hydrogels were prepared for deoxyribonucleic acid (DNA) adsorption. Instead of directly grafting the N,N‐dimethylacrylamide (DMAAm) monomer onto the chitosan (CT) chains, poly(N,N‐dimethylacrylamide) with carboxylic acid end group (PDMAAm‐COOH) was firstly synthesized by free‐radical polymerization using mercaptoacetic acid (MAAc) as the chain‐transfer agent and then grafted onto the CT having amino groups. The synthesis of PDMAAm‐COOH and its grafting onto the CT chains were confirmed by attenuated total reflectance Fourier transform infrared (ATR‐FTIR) spectroscopy. From gel permeation chromatography measurements, the number‐average molecular weight (M _n) and polydispersity index of PDMAAm‐COOH were found as 2400 g/mol and 2.3, respectively. The PDMAAm‐g‐CT hydrogels were utilized as the adsorbents in DNA adsorption experiments conducted at +4°C in a trisEDTA solution of pH 7.4. The hydrogels produced with higher PDMAAm‐COOH content exhibited higher DNA adsorption capacity. The DNA adsorption capacity up to 4620 μg DNA/g dry gel could be achieved with the PDMAAm‐g‐CT hydrogels prepared in 80.0 wt % PDMAAm‐COOH feed concentration. This value is approximately seven times higher than that of CT alone. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Simultaneous lower and upper critical solution temperature‐type co‐nonsolvency behaviour exhibited in water–dioxane mixtures by linear copolymers and hydrogels containing N‐isopropylacrylamide and N,N‐dimethylacrylamide

The co‐nonsolvency behaviour in water–dioxane mixtures of linear copolymers and hydrogels consisting of N‐isopropylacrylamide (NIPAM) and N,N‐dimethylacrylamide (DMAM) was studied as a function of solvent composition and temperature. The composition of the copolymers, P(NIPAM‐co‐DMAMx), in DMAM units, x, varies from x = 0 up to x = 100%. It is shown that the copolymers combine the lower critical solution temperature (LCST)‐type co‐nonsolvency behaviour of poly‐NIPAM with the upper critical solution temperature (UCST)‐type co‐nonsolvency behaviour of poly‐DMAM. Depending on x, both the LCST‐ and UCST‐type co‐nonsolvency behaviour may be simultaneously observed in water‐rich and dioxane‐rich solvent mixtures, respectively. Due to this complex phase separation behaviour, the variation of the reduced viscosity of the linear copolymers, as well as the swelling–deswelling behaviour of the respective hydrogels, are shown to be temperature‐ and solvent‐sensitive. Copyright © 2006 Society of Chemical Industry     

Functionalization of Poly(propylene) Fabric with 4‐Vinylpyridine,N,N‐Dimethylacrylamide and Styrene by γ‐Radiation‐Induced Grafting in an Aqueous Environment

Summary: VP and co‐monomers DMAAm and ST were successfully grafted onto a PP fabric in an emulsion copolymerization process initiated by γ‐radiation. The radiation dose, concentration of VP, the ratio of VP/DMAAm and VP/ST in the reaction solution, and the reaction temperature dependent graft copolymerization were investigated. The order of dependence of the initial rate of grafting on the radiation dose was found to be in the range of 1.2 to 0.93 for VP; 0.84 to 0.70 for VP/DMAAm and for VP/ST was in the range of 0.59 to 0.41. The activation energy of the graft copolymer reaction was determined to be 40.18 J · mol^?1 for 0.464 mol · L^?1 VP. In the case of co‐monomer mixtures (VP/DMAAm: 0.464/0.5) the energy of activation was noticeably higher at 49.71 J · mol^?1 while for VP/ST (0.464/0.436) the activation energy was same as that of VP. XRD results showed that overall crystallinity significantly decreased with the increase of graft weight with a noticeable change in the chemical structure of the PP, indicating that the graft copolymer reaction was taking place both in the amorphous and crystalline regions of PP. A similar characteristic behavior was also obtained by DSC, which revealed the presence of an endotherm process in the range of 25 to 130 °C depending on the degree of grafting, attributed to the grafted chains of the monomer/co‐monomers. In order to determine the graft copolymer reaction of VP, DMAAm and ST onto the backbone of PP, the reaction products were characterized by FTIR spectroscopy. A good correlation was found between changes of crystallinity and level of graft copolymerization as determined by WAXRD and DSC.

Typical XRD traces of as‐received PP fabric (PPF) and grafted with VP (PPF‐g‐VP).     

Thermosensitive Poly[(2‐(diethylamino)ethyl methacrylate)‐co‐(N,N‐dimethylacrylamide)] Cryogels Prepared by a Two‐Step Polymerization Method

Summary: Temperature‐sensitive P(DEAEMA‐co‐DMAAm) cryogels with five different DMAAm contents were synthesized via a two‐step polymerization method, the initial polymerization being conducted for various times at 22 °C, followed by polymerization at ?26 °C for 24 h. The influence of the first‐step time and the content of DMAAm on the swelling ratio and network parameters such as the polymer/solvent interaction parameter, the average molecular mass between crosslinks, and the mesh size of the cryogels were reported and discussed. The swelling studies indicated that the swelling increased in the following order: 22C45 > 22C30 > 22C15 > 22C0. The cryogels exhibited swelling/deswelling transitions (reentrant phenomena) in water depending on temperature. These properties were attributed to the macroporous and regularly arranged network of the cryogels. Scanning electron microscope graphs reveal that the macroporous network structure of the cryogels can be adjusted by applying a two‐step polymerization.

Chemical structure of the P(DEAEMA‐co‐DMAAm) cryogels.     

Swelling characteristics of thermo‐ sensitive poly[(2‐diethylaminoethyl methacrylate)‐co‐(N,N‐dimethylacrylamide)] porous hydrogels

Temperature‐sensitive poly[(2‐diethylaminoethyl methacrylate)‐co‐(N,N‐dimethylacrylamide)] [P(DEAEMA‐co‐DMAAm)] hydrogels with five different DMAAm contents were synthesized with and without the addition of sodium carbonate as porosity generator. The synthesized hydrogels were characterized with dry gel density measurements, scanning electron microscopy observation and the determination of swelling ratio. The influence of the pore‐forming agent and content of DMAAm on swelling ratio and network parameters such as polymer–solvent interaction parameter (χ), average molecular mass between crosslinks (M?_c) and mesh size (ζ) of the cryogels are reported and discussed. The swelling and deswelling rates of the porous hydrogels are much faster than for the same type of hydrogels prepared via conventional methods. At a temperature below the volume phase transition temperature, the macroporous hydrogels also absorbed larger amounts water compared to that of conventional hydrogels and showed obviously higher equilibrated swelling ratios in aqueous medium. In particular, the unique macroporous structure provided numerous water channels for water diffusion in or out of the matrix and, therefore, an improved response rate to the external temperature changes during the deswelling and swelling processes. These properties are attributed to the macroporous and regularly arranged network of the porous hydrogels. Scanning electron micrographs reveal that the macroporous network structure of the hydrogels can be adjusted by applying porosity generation methods during the polymerization reaction. Copyright © 2007 Society of Chemical Industry     

Interpolymer interactions and miscibility in poly(n‐butyl methacrylate‐co‐methacrylic acid)/poly(styrene‐co‐N,N‐dimethyl acrylamide) blends

The miscibility of poly(n‐butyl methacrylate‐co‐methacrylic acid) containing 18 mol % methacrylic acid (BMAM‐18) and poly(styrene‐co‐N,N‐dimethyl acrylamide) containing 17 mol % N,N‐dimethyl acrylamide (SAD‐17) was investigated with viscometry, differential scanning calorimetry (DSC), and Fourier transform infrared (FTIR) spectroscopy. The DSC analysis showed a single glass‐transition temperature for all the blends, indicating that these copolymers were miscible over the entire composition range. The glass‐transition temperatures of these blends were higher than those calculated with the additivity rule. This was characteristic of the presence of specific interactions. The interactions between BMAM‐18 and the tertiary amide of SAD‐17 were studied with FTIR spectroscopy, which revealed that hydrogen‐bonding interactions occurred between the hydroxyl groups of BMAM‐18 and the carbonyl amide of SAD‐17. A new band characterizing these interactions appeared around 1613 cm^?1. The quantitative results showed that the fraction of the associated amide increased with an increase in the amount of the acidic BMAM‐18 copolymer. Although BMAM‐18 and SAD‐17 led to homogeneous solutions in butan‐2‐one, as the concentration of N,N‐dimethyl acrylamide increased to 32 mol % [as within the poly(styrene‐co‐N,N‐dimethyl acrylamide) containing 32 mol % N,N‐dimethyl acrylamide], complexation occurred when this latter compound was mixed with BMAM‐18 in butan‐2‐one. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2717–2724, 2006     

Effect of solvent on the free radical polymerization of N,N‐dimethylacrylamide

The free radical photopolymerization of N,N‐dimethylacrylamide was investigated at 25 °C and at low conversion in several solvents ranging from weak polar solvents to water. The polymerization is strongly accelerated in the aqueous medium, with the polymerization rate increasing one order of magnitude when the solvent is changed from an organic one to aqueous medium. These results were analysed in terms of macroradical conformation, effect of medium viscosity, aggregate formation, hydrogen bond formation and effect of temperature. The results suggest that the main factor that controls the polymerization rate is a kinetic effect due to the hydrogen bonding between the amide carbonyl group and water molecules. Also, we found that polymer properties, such as the thermodynamic quality of the solvent for the polymer backbone and molecular weight control using transfer agents, are influenced by the intermolecular hydrogen bonding. Copyright © 2010 Society of Chemical Industry     

Electrospinning of Colloidal Lignin in Poly(ethylene oxide) N,N‐Dimethylformamide Solutions

Electrospinning of sulfur‐free softwood lignin (SFSL) in N,N‐dimethylformamide (DMF) is reported as is and with poly(ethylene oxide) (PEO). SFSL macromolecules behave as rigid spheres, instead of free draining macromolecules in DMF. Hence they are investigated as colloids. Colloidal SFSL generates uniform fibers only at the volume fraction of 0.63. It is due to the sufficiently high longest mean relaxation time at the volume fraction of 0.63. Colloidal SFSL below the volume fraction of 0.63 does not exhibit any measurable viscoelasticity and also does not generate any uniform fibers. Bead‐free fibers are generated at volume fractions below 0.63 only by adding PEO. PEO presence brings elasticity to colloidal SFSL and produces bead‐free fibers only above the entanglement concentration of PEO in DMF. The presence of SFSL macromolecules does not cause any interactions with PEO molecules, except it reduces the available of free volume for PEO chains in DMF.

     

Monitoring of the Synthesis of Hyperbranched Poly(urea‐urethane)s by Real‐Time Attenuated Total Reflection (ATR)‐FT‐IR Spectroscopy

Summary: The reaction of 2,4‐TDI and DEA, as an A₂ + B^*B₂ polymerization system towards hyperbranched HPUs was followed using in situ ATR‐FT‐IR spectroscopy. The decrease in intensity of the NCO absorption band of the reactive isocyanate group of 2,4‐TDI along with the formation and growth of the new characteristic bands of urethane and urea groups were detected. The reactivity difference of both NH and OH groups towards the NCO group at low temperatures was proven. The rate of the reaction was found to be affected by changing the temperature, the rate of addition of the B^*B₂ monomer and the type of solvent. Moreover, the increase of the carbonyl vibration and the amide II bands of urea was very obvious during the addition of the stopper DEA. Thus, it was possible to verify the individual reaction steps of this complex polyreaction and to correlate these with the structural development of the resulting macromolecules.

Characteristic vibration bands of urethane and urea groups in the IR spectra (1 780–1 480 cm^?1) during the polymerization reaction.     

Grafted polysaccharides based on acrylamide and N,N‐dimethylacrylamide: Preparation and investigation of their flocculation performances

The graft copolymerization of N,N‐dimethylacrylamide (DMA) and acrylamide (AM) were carried out onto different polysaccharide backbones separately. The graft copolymers were synthesized by ceric ion induced redox polymerization technique. Three polysaccharides were used, namely hydroxyethyl starch (HES), hydroxyethyl cellulose (HEC) and Amylopectin (AP), for the grafting reactions. Among the three polysaccharides, HEC has linear structure, while HES and AP have a branch one. The graft copolymers were characterized by intrinsic viscosity measurements, FTIR spectroscopy, NMR (both ¹H and ¹³C) spectroscopy, and thermal analysis. Flocculation performances of the graft copolymers were evaluated in 1 wt % kaolin and in 0.25 wt % iron ore suspensions. A detailed comparative study of the flocculation properties of the synthetic graft copolymers was also made. It showed that graft copolymers based on DMA were better flocculants than those based on AM. Among the synthetic graft copolymers, HES‐g‐Poly (DMA) performed best when compared with the other synthetic graft copolymers as well as to the commercial flocculants in the same suspensions. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Supertoughness in Polysulfone/Poly(ethylene‐octene) Blends

Summary: Poly(sulfone of Bisphenol A) (PSU) based blends were obtained by melt blending PSU with up to 15 wt.‐% poly(ethylene‐octene) either modified with maleic anhydride (mPEO) or not (PEO). The dispersed particle size was small and similar in blends with PEO or mPEO. These facts indicated respectively that the interfacial tension was low and the lack of compatibilizing effect of mPEO. Some preferential presence of PEO in the outer surface of the specimens was observed, and was attributed to the large viscosity difference between the two components of the blends. This had no effect on the modulus of elasticity, but speeded up both the yield stress and ductility decreases at rubber contents above 3.25 wt.‐%. However, despite the immiscibility of the components, and thanks to the small particle size of the blends, super‐toughness was attained in the unmodified PSU/PEO blends. This was at PEO contents (3.25 wt.‐%) at which the modulus, yield stress and ductility of the blends were almost as good as those of pure PSU. It appeared that a change of the chemical nature of the rubber did not influence by itself super‐toughness, unless it was accompanied by either a morphological or adhesion change.

Impact strength of PSU‐based blends vs. PEO (○) or mPEO (?) content.     

Amphiphilic 2‐ethyl hexyl methacrylate‐b‐N,N′‐dimethylacrylamide diblock copolymer monolayer behaviour at the air − water interface†

The surface activities of two amphiphilic diblock copolymers containing 2‐ethyl hexyl methacrylate‐b‐N,N′‐dimethylacrylamide (EHMA‐b‐DMA) possessing hydrophobic segments of different chain lengths were studied. Toward this end, surface pressure?area (π?A) isotherms, static and dynamic elasticities and the ν exponent of the excluded volume of polymers forming monolayers at the air?water interface were measured. The degree of hydrophobicity of the diblock copolymers was estimated by determining their surface energy values from contact angle measurements. The morphology of the monolayer at different surface pressures was studied by Brewster angle microscopy. Both copolymers were observed to form stable and elastic monolayers, and their collapse was observed to occur at similar surface pressures. Langmuir?Blodgett films were successfully deposited onto mica and silicon wafers and analysed by atomic force microscopy. © 2014 Society of Chemical Industry     

Compatibility studies with blends based on poly(n‐butyl methacrylate) and polyacrylonitrile

In this study, poly(n‐butyl methacrylate) (PBMA) was prepared by a suspension polymerization process, and blending with polyacrylonitrile (PAN) in N,N‐dimethyl acetamide to prepare PAN/PBMA blends in various proportions. Hansen's three dimensional solubility parameters of PAN and PBMA were calculated approximately through the contributions of the structural groups. The compatibility in these blend systems was studied with theoretical calculations as well as experimental measurements. Viscometric methods, Fourier transform infrared spectroscopy, dynamic mechanical analysis, scanning electron microscopy, and thermogravimetric analysis were used for this investigation. All the results showed that a partial compatibility existed in PAN/PBMA blend system, which may be due to the intermolecular interactions between the two polymers. And, the adsorption experiment results showed that the addition of PBMA contributed to the enhancing adsorptive properties of blend fibers, which lays the foundation for further studying PAN/PBMA blend fibers with adsorptive function. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

A study on solution properties of poly(N,N‐diethylacrylamide‐co‐acrylic acid)

Poly(N,N‐diethylacrylamide) (PDEA), poly(acrylic acid) (PAA), and a series of (N,N‐diethylacrylamide‐co‐acrylic acid) (DEA‐AA) random copolymers were synthesized by the method of radical polymerization. The measurement of turbidity showed that the phase behaviors of the brine solutions of the copolymers changed dramatically with the mole fraction of DEA (x) in these copolymers. Copolymers cop6 (x = 0.06) and cop11 (x = 0.11) in which acrylic acid content was higher presented the upper critical solution temperature (UCST) phase behaviors similar to PAA. Copolymer cop27 (x = 0.27) presented the lower critical solution temperature (LCST) behavior similar to PDEA. While copolymer cop18 (x = 0.18) in which acrylic acid content was moderate presented both UCST and LCST behaviors. The solution properties of the polymers were investigated by measurements of viscosity, fluorescence, and pH. It is reasonable to suggest that the sharp change of the phase behavior may be attributed to the interaction between acrylamide group and carboxylic group in the (DEA‐AA) copolymers. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Metal complexation studies of amylopectin‐graft‐poly[(N,N‐dimethylacrylamide)‐co‐(acrylic acid)]: a biodegradable synthetic graft copolymer

Synthesis of amylopectin‐graft‐poly[(N,N‐dimethylacrylamide)‐co‐(acrylic acid)] was carried out using solution polymerization technique with potassium persulfate as the initiator. The graft copolymer was characterized by measuring molecular weight using size exclusion chromatography, thermal analysis and Fourier transform infrared (FTIR) spectroscopy. The synthetic graft copolymer was used for the removal of some potentially toxic metal ions, Cu(II), Zn(II) and Ni(II), from their aqueous solutions. Various operating parameters like the amount of adsorbent, solution pH, contact time and temperature were studied. The adsorption data were well described by the pseudo‐second‐order and Langmuir isotherm models. Metal complexation studies were carried out experimentally using cyclic voltammetry and UV‐visible and FTIR spectroscopies. The metal complex structure was also studied theoretically using density functional theory with the Gaussian 09 program and the geometry of the complex structure was optimized. The metal complexation ability of the graft polymer was in the order Cu(II) > Ni(II) > Zn(II). Calculation of the various thermodynamic parameters was also done. The negative value of free energy change indicates the spontaneous nature of the adsorption. © 2015 Society of Chemical Industry     

Miscibility and specific interactions in blends of poly(vinyl phenyl ketone hydrogenated) with poly(2,6‐dimethyl‐1,4‐phenylene oxide)

The miscibility behavior of poly(vinyl phenyl ketone hydrogenated) (PVPhKH) and poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) are studied by differential scanning calorimetry, thermomechanical analysis, and FTIR spectroscopy. Two miscibility windows between 10 to 40 and 60 to 90 wt % PPO are detected. Only the blend with 50 wt % PPO is immiscible. The best fit of the Gordon–Taylor equation of the experimental glass‐transition temperatures for miscible PVPhKH/PPO blends is shown. A study by FTIR spectroscopy suggests that hydrogen bonding interactions are formed between the hydroxyl groups of PVPhKH and the ether groups of PPO. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1887–1892, 2004