A wide-band RF front-end for multiband multistandard high-linearity low-IF wireless receivers

A wide-band radio-frequency (RF) front-end is designed with a balanced combined low-noise amplifier and a switching mixer (a low-noise converter) in an RF Si-bipolar process with an f/sub T/ of 25 GHz. The circuit achieves 20-dB conversion gain, higher than -4.5-dBm RF-to-IF IIP/sub 3/ (+15.5-dBm OIP/sub 3/) and less than 3.8-dB double-side-band noise figure in 900-MHz (e.g., GSM) and 1.9-GHz (e.g., WCDMA) frequency bands. The -1-dB compression point is -20 dBm at 13-mA DC current consumption from a single 5-V supply. The local-oscillator leakage to the input is less than -56 dBm in the 900-MHz band and less than -63 dBm in the 1.9-GHz band. The -3-dB bandwidth of the amplifier is larger than 3 GHz and a wide-band matching at the input with -10 to -41-dB S/sub 11/ is achieved in the frequency bands of interest by applying a dual-loop wide-band active feedback. The die area is 0.69 /spl times/ 0.9 mm/sup 2/. The circuit is suitable for area-efficient multiband multistandard low-IF receivers.     

A subharmonically injected LC delay line oscillator for 17-GHz quadrature LO generation

An injection-locked delay line oscillator multiplies a 5-6-GHz input by 3 to generate I/Q LO signals for 17-GHz wireless networking applications. I/Q errors caused by asymmetric injection are minimized by symmetric injection via a passive polyphase prefilter. Passive delay lines set the measured free-running frequency of the LC ring oscillator to 16.24 GHz. The measured locking range for a 0 dBm (50 /spl Omega/) input is 14.6-17.86 GHz. Input-to-output phase noise degradation is negligible, and I/Q amplitude and phase errors are <0.17 dB and <2/spl deg/, respectively. Power consumption of the 1.2/spl times/1.4 mm/sup 2/ 0.2 /spl mu/m SiGe BiCMOS testchip (excluding buffers) is 22 mW at 2.2 V.     

A direct-conversion CMOS transceiver for the 802.11a/b/g WLAN standard utilizing a Cartesian feedback transmitter

A fully integrated dual-band transceiver is implemented in 0.18-/spl mu/m CMOS and is compliant with the IEEE 802.11a/b/g standards. The direct-conversion transceiver occupies 12 mm/sup 2/ in a QFN-40 package. A fractional-N synthesizer operates at twice the channel frequency, covering continuously bands from 4.9 to 5.9 GHz, as well as the 2.4-GHz band. The 5- and 2.4-GHz receivers achieve a sensitivity level below -73 dBm in the 54-Mb/s mode and below -93 dBm in the 6-Mb/s mode, while consuming 230 mW. A fast RSSI-channel power-detection system allows to power-down signal processing in the listen mode. The 5- and 2.4-GHz transmitters implement a wideband Cartesian feedback loop for enhanced EVM performances and improved spectrum masks compliance. The transmitters deliver -2-dBm average power with an EVM of 3% in the 54-Mb/s mode while consuming 300 mW.     

A dual-band 5.15-5.35-GHz, 2.4-2.5-GHz 0.18-/spl mu/m CMOS transceiver for 802.11a/b/g wireless LAN

A single-chip dual-band 5.15-5.35-GHz and 2.4-2.5-GHz zero-IF transceiver for IEEE 802.11a/b/g WLAN systems is fabricated on a 0.18-/spl mu/m CMOS technology. It utilizes an innovative architecture including feedback paths that enable digital calibration to help eliminate analog circuit imperfections such as transmit and receive I/Q mismatch. The dual-band receive paths feature a 4.8-dB (3.5-dB) noise figure at 5.25 GHz (2.45 GHz). The corresponding sensitivity at 54 Mb/s operation is -76 dBm for 802.11a and -77 dBm for 802.11g, both referred at the input of the chip. The transmit chain achieves output 1-dB compression at 6 dBm (9 dBm) at 5 GHz (2.4 GHz) operation. Digital calibration helps achieve an error vector magnitude (EVM) of -33 dB (-31 dB) at 5 GHz (2.4 GHz) while transmitting -4 dBm at 54Mb/s. The die size is 19.3 mm/sup 2/ and the power consumption is 260 mW for the receiver and 320 mW (270 mW) for the transmitter at 5 GHz (2.4 GHz) operation.     

A 28-GHz monolithic integrated quadrature oscillator in SiGe bipolar technology

This paper presents a 28-GHz monolithic quadrature voltage-controlled oscillator (QVCO) realized in a preproduction 0.4-/spl mu/m SiGe bipolar technology with 85-GHz transit frequency. QVCOs efficiently drive quadrature modulators and demodulators in receivers or transmitters. At 28.9 GHz, the circuit provides -14.7 dBm of output power and phase noise of -84.2 dBc/Hz at a 1-MHz offset. The two output signals are in quadrature with phase error of about 5/spl deg/. Tuning of the QVCO may be done in the frequency range from 24.8 to 28.9 GHz with nearly constant output power. The circuit consumes 25.8 mA from the 5 V voltage supply.     

A 1.8-V 2.4/5.15-GHz dual-band LCVCO in 0.18-/spl mu/m CMOS technology

A dual band, fully integrated, low phase-noise and low-power LC voltage-controlled oscillator (VCO) operating at the 2.4-GHz industrial scientific and medical band and 5.15-GHz unlicensed national information infrastructure band has been demonstrated in an 0.18-/spl mu/m CMOS process. At 1.8-V power supply voltage, the power dissipation is only 5.4mW for a 2.4-GHz band and 8mW for a 5.15-GHz band. The proposed VCO features phase-noise of -135dBc/Hz at 3-MHz offset frequency away from the carrier frequency of 2.74GHz and -126dBc/Hz at 3-MHz offset frequency away from 5.49GHz. The oscillator is tuned from 2.2 to 2.85GHz in the low band (2.4-GHz band) and from 4.4 to 5.7GHz in the high band (5.15-GHz band).     

Efficient direct locking of colliding pulse mode-locked lasers on semi-insulating substrate at 1.5 /spl mu/m

Colliding pulse mode-locked (CPM) lasers operating at 1.5 /spl mu/m and 36-GHz repetition frequency were fabricated on semi-insulating substrates. An RF electrical signal at a repetition rate of 36 GHz was injected into the saturable absorber and hybrid CPM was observed for RF powers as low as -9.0 dBm with a phase noise level of < -70 dBc/Hz at 5-kHz offset. Linewidth narrowing and pedestal suppression became pronounced for RF powers as low as 0 dBm. With an injected RF power of +8 dBm, the worst-case timing jitter was reduced from 4.8 to 0.69 ps ( 100 Hz to 10 MHz).     

A single-chip dual-band tri-mode CMOS transceiver for IEEE 802.11a/b/g wireless LAN

A single-chip dual-band tri-mode CMOS transceiver that implements the RF and analog front-end for an IEEE 802.11a/b/g wireless LAN is described. The chip is implemented in a 0.25-/spl mu/m CMOS technology and occupies a total silicon area of 23 mm/sup 2/. The IC transmits 9 dBm/8 dBm error vector magnitude (EVM)-compliant output power for a 64-QAM OFDM signal. The overall receiver noise figure is 5.5/4.5 dB at 5 GHz/2.4 GHz. The phase noise is -105 dBc/Hz at a 10-kHz offset and the spurs are below -64 dBc when measured at the 5-GHz transmitter output.     

A multiband /spl Delta//spl Sigma/ fractional-N frequency synthesizer for a MIMO WLAN transceiver RFIC

This work presents a shared fractional-N synthesizer used by two dual-band 802.11 radios integrated on a single chip for 2/spl times/2 multiple-input multiple-output (MIMO) applications. Additional 2/spl times/2 MIMO chips can be used in a system by phase synchronizing the signal paths through a bidirectional LO porting scheme developed for this application. This synthesizer was fully integrated with the exception of an off-chip loop filter. The synthesizer is a /spl Delta//spl Sigma/-based fractional-N frequency synthesizer with three on-chip LC tuned VCOs to cover the entire frequency bands specified in the IEEE 802.11a/b/g and Japanese WLAN standards. The radio uses a variable IF frequency so that both the RF LO and IF LO can be derived from a single synthesizer saving chip area and power. The synthesizer includes a programmable second/third-order /spl Delta//spl Sigma/ noise shaper, a phase frequency detector, a differential charge pump, and a 6-bit multimodulus divider (MMD). The nominal jitter from 100 Hz to 10 MHz is 0.63-0.86/spl deg/ rms in the 5-GHz band and 0.35-0.43/spl deg/ rms in the 2.4-GHz band. The maximum frequency deviation of the synthesizer when enabling the transmitter is less than 150 kHz and the frequency error settles to 2 kHz in less than 12 /spl mu/s. For MIMO applications requiring more than two full paths, a single synthesizer on one die can be used to generate the LOs for all other radios integrated in different dies.     

A fully integrated 24-GHz phased-array transmitter in CMOS

This paper presents the first fully integrated 24-GHz phased-array transmitter designed using 0.18-/spl mu/m CMOS transistors. The four-element array includes four on-chip CMOS power amplifiers, with outputs matched to 50 /spl Omega/, that are each capable of generating up to 14.5 dBm of output power at 24 GHz. The heterodyne transmitter has a two-step quadrature up-conversion architecture with local oscillator (LO) frequencies of 4.8 and 19.2 GHz, which are generated by an on-chip frequency synthesizer. Four-bit LO path phase shifting is implemented in each element at 19.2 GHz, and the transmitter achieves a peak-to- ratio of 23 dB with raw beam-steering resolution of 7/spl deg/ for radiation normal to the array. The transmitter can support data rates of 500 Mb/s on each channel (with BPSK modulation) and occupies 6.8 mm /spl times/ 2.1 mm of die area.     

A 4-91-GHz traveling-wave amplifier in a standard 0.12-/spl mu/m SOI CMOS microprocessor technology

This paper presents five-stage and seven-stage traveling-wave amplifiers (TWA) in a 0.12-/spl mu/m SOI CMOS technology. The five-stage TWA has a 4-91-GHz bandpass frequency with a gain of 5 dB. The seven-stage TWA has a 5-86-GHz bandpass frequency with a gain of 9 dB. The seven-stage TWA has a measured 18-GHz noise figure, output 1-dB compression point, and output third-order intercept point of 5.5 dB, 10 dBm, and 15.5 dBm, respectively. The power consumption is 90 and 130 mW for the five-stage and seven-stage TWA, respectively, at a voltage power supply of 2.6 V. The chips occupy an area of less than 0.82 and 1 mm for the five-stage and seven-stage TWA, respectively.     

On the feasibility of CMOS multiband phase shifters for multiple-antenna transmitters

We present the design of an integrated multiband phase shifter in RF CMOS technology for phased array transmitters. The phase shifter has an embedded classical distributed amplifier for loss compensation. The phase shifter achieves a more than 180/spl deg/ phase tuning range in a 2.4-GHz band and a measured more than 360/spl deg/ phase tuning range in both 3.5-GHz and 5.8-GHz bands. The return loss is less than -10dB at all conditions. The feasibility for transmitter applications is verified through measurements. The output power at a 1-dB compression point (P/sub 1 dB/) is as high as 0.4dBmat 2.4GHz. The relative phase deviation around P/sub 1 dB/ is less than 3/spl deg/. The design is implemented in 0.18-/spl mu/mRF CMOS technology, and the chip size is 1200/spl mu/m /spl times/ 2300 /spl mu/m including pads.     

Compact 28-GHz subharmonically pumped resistive mixer MMIC using a lumped-element high-pass/band-pass balun

This work reports a novel lump-element balun for use in a miniature monolithic subharmonically pumped resistive mixer (SPRM) microwave monolithic integrated circuit. The proposed balun is simply analogous to the traditional Marchand balun. The coupled transmission lines are replaced by lump elements, significantly reducing the size of the balun. This balun requires no complicated three-dimensional electromagnetic simulations, multilayers or suspended substrate techniques; therefore, the design parameters are easily calculated. A 2.4-GHz balun is demonstrated using printed circuit board technology. The measurements show that the outputs of balun with high-pass and band-pass responses, a 1-dB gain balance, and a 5/spl deg/ phase balance from 1.7 to 2.45 GHz. The balun was then applied in the design of a 28-GHz monolithic SPRM. The measured conversion loss of the mixer was less than 11dB at a radio frequency (RF) bandwidth of 27.5-28.5 GHz at a fixed 1 GHz IF, a local oscillator (LO)-RF isolation of over 35 dB, and a 1-dB compression point higher than 9 dBm. The chip area of the mixer is less than 2.0 mm/sup 2/.     

1-GHz, 200/spl deg/C, SiC MESFET Clapp oscillator

A SiC Clapp oscillator fabricated on an alumina substrate with chip capacitors and spiral inductors is designed for high-temperature operation at 1GHz. The oscillator operated from 30/spl deg/C to 200/spl deg/C with an output power of 21.8dBm at 1GHz and 200/spl deg/C. The efficiency at 200/spl deg/ C is 15%. The frequency variation over the temperature range is less than 0.5%.     

K- and Q-bands CMOS frequency sources with X-band quadrature VCO

Fully integrated 10-, 20-, and 40-GHz frequency sources are presented, which are implemented with a 0.18-/spl mu/m CMOS process. A 10-GHz quadrature voltage-controlled oscillator (QVCO) is designed to have output with a low dc level, which can be effectively followed by a frequency multiplier. The proposed multipliers generate signals of 20 and 40 GHz using the harmonics of the QVCO. To have more harmonic power, a frequency doubler with pinchoff clipping is used without any buffers or dc-level shifters. The QVCO has a low phase noise of -118.67 dBc/Hz at a 1-MHz offset frequency with a 1.8-V power supply. The transistor size effect on phase noise is investigated. The frequency doubler has a low phase noise of -111.67 dBc/Hz at a 1-MHz offset frequency is measured, which is 7 dB higher than a phase noise of the QVCO. The doubler can be tuned between 19.8-22 GHz and the output is -6.83 dBm. A fourth-order frequency multiplier, which is used to obtain 40-GHz outputs, shows a phase noise of -102.0 dBc/Hz at 1-MHz offset frequency with the output power of -18.0 dBm. A large tuning range of 39.3-43.67 GHz (10%) is observed.     

A 0.25-/spl mu/m 20-dBm 2.4-GHz CMOS power amplifier with an integrated diode linearizer

A 2.4-GHz CMOS power amplifier (PA) with an output power 20 dBm using 0.25-/spl mu/m 1P5M standard CMOS process is presented. The PA uses an integrated diode connected NMOS transistor as a diode linearizer. It is believed that this is the first reported use of the diode linearization technique in CMOS PA design. It shows effective improvement in linearity from gain compression and ACPR measured results. Measurements are performed by using an FR-4 PCB test fixture. The fabricated power amplifier exhibits an output power of 20 dBm and a power-added efficiency as high as 28%. The obtained PA performances demonstrate the standard CMOS process potential for medium power RF amplification at 2.4 GHz wireless communication band.     

Efficient generation of guided millimeter-wave power by photomixing

A 70-GHz bandwidth commercial photodiode has been coupled to W-band waveguide and used as a photomixing source from 75 to 170 GHz. Maximum power conversion efficiency of 1.8% was obtained at 75 GHz, where an optical input of +10 dBm yielded a nonsaturated millimeter-wave (mm-wave) power of -7.5 dBm. Optimizing the photomixer backshort tuning at individual frequencies showed that the mm-wave power decreased with frequency to a level of -30 dBm at 170 GHz. Fixed tuning allowed the generation of power across the full waveguide band from 75 to 110 GHz, with a variation within 5 dB across the majority of the band     

Subharmonically pumped CMOS frequency conversion (up and down) circuits for 2-GHz WCDMA direct-conversion transceiver

Subharmonically pumped frequency down- and upconversion circuits are implemented in 0.18-/spl mu/m mixed-mode CMOS technology for 2-GHz direct-conversion WCDMA transceiver applications. These circuits operate in quadrature double-balanced mode and a required octet-phases (0/spl deg/, 45/spl deg/, 90/spl deg/, 135/spl deg/, 180/spl deg/, 225/spl deg/, 270/spl deg/, and 315/spl deg/) local oscillator (LO) signal comes from an active multiphases LO generator composed of a polyphase filter and active 45/spl deg/ phase shifting circuits. For linearity improvement, predistortion compensation and negative feedback schemes are used in the frequency down- and upconversion circuits, respectively. The downconverter achieves a conversion voltage gain of 20 dB (to 1-M/spl Omega/ load), 4-dBm IIP3 (18-dBm OIP3 to 50-/spl Omega/ load), 41-dBm IIP2 and 8.5-dB DSB NF at 1-MHz IF frequency, consuming 13.4 mA from 1.8-V supply, in the WCDMA Rx band (2110-2170 MHz). The upconverter, operating as two switched gain modes in the WCDMA Tx band (1920-1980 MHz), consumes 19.4 mA from 1.8-V supply and shows 14.5-dB conversion power gain, 15 -dBm OIP3 (0.5-dBm IIP3) and -11 dBm P/sub 1dB/ at maximum gain mode. At minimum gain mode, it realizes -0.3-dB conversion loss, 10.7-dBm OIP3 (11-dBm IIP3) and 0-dBm P/sub 1dB/, respectively. 3GPP WCDMA modulation tests are performed for both up- and downconversion circuits and the results are discussed in this paper.     

A highly integrated dual-band multimode wireless LAN transceiver

A fully integrated radio transceiver chip for the 2.4- and 5-GHz WLAN standards 802.11a/b/g is presented in a 0.25-/spl mu/m 40-GHz BiCMOS technology. The chip integrates the low-noise amplifiers, mixers, channel filters, programmable gain control, synthesizers with voltage-controlled oscillators and reference oscillator, transmitters, antialiasing filters, and voltage regulators. The key performances of the presented transceiver are a receive sensitivity of -85 dBm and -74 dBm for 11-Mb/s complementary code keying (CCK) and 54 Mb/s orthogonal frequency division multiplexing (OFDM) modes, respectively, and an error vector magnitude of -35 dB measured at the transmitter with an output power of -4 dBm at 54-Mb/s 802.11a mode. The transceiver exceeds all IEEE requirements for the 802.11a/b/g CCK and OFDM standards and supports a frequency range of 4.9 to 6 GHz for the future extensions of the 802.11a standard in different countries.     

A 1-V transformer-feedback low-noise amplifier for 5-GHz wireless LAN in 0.18-/spl mu/m CMOS

A low-noise amplifier (LNA) uses low-loss monolithic transformer feedback to neutralize the gate-drain overlap capacitance of a field-effect transistor (FET). A differential implementation in 0.18-/spl mu/m CMOS technology, designed for 5-GHz wireless local-area networks (LANs), achieves a measured power gain of 14.2 dB, noise figure (NF, 50 /spl Omega/) of 0.9 dB, and third-order input intercept point (IIP3) of +0.9 dBm at 5.75 GHz, while consuming 16 mW from a 1-V supply. The feedback design is benchmarked to a 5.75-GHz cascode LNA fabricated in the same technology that realizes 14.1-dB gain, 1.8-dB NF, and IIP3 of +4.2 dBm, while dissipating 21.6 mW at 1.8 V.