Optical properties and structure of R2O–Ga2O3–SiO2 and RO–Ga2O3–SiO2 glasses

Refractive index and molar refraction of Li₂O–, Na₂O–, CaO–, and BaO–Ga₂O₃–SiO₂ glasses have been used to test the validity of a structural model of silicate glasses containing Ga₂O₃ glasses. Ga₂O₃ enters these types of glass in a similar manner as Al₂O₃. It is assumed that, for (SiO₂/Ga₂O₃) >1 and (Ga₂O₃/R₂O) ≤1, Ga₂O₃ associates primarily with modifier oxides to form GaO₄ units. The rest of modifier oxide forms silicate units with non-bridging oxygen ions. Silicate structural units have the same factors as found for binary alkali- and alkaline earth silicate glasses. Differences between experimental and model values suggest another structure for (Ga₂O₃/SiO₂) ≥1.     

Crystallization and magnetic properties of a 10Li2O–9MnO2–16Fe2O3–25CaO–5P2O5–35SiO2 glass

The crystallization behavior and magnetic properties of 10Li₂O–9MnO₂–16Fe₂O₃–25CaO–5P₂O₅–35SiO₂ (10LFS) glass have been studied using differential thermal analysis (DTA), X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray spectrometry (EDS), transmission electron microscopy (TEM) and selected area electron diffraction (SAED) to observe the crystallization behavior and a superconducting quantum interference device (SQUID) for measurements of the magnetic properties. The DTA shows that the 10LFS glass has one broad exothermic peak at approximately 674 °C and one sharp (the highest) exothermic peak at 764 °C. When the 10LFS glass crystallized at 850 °C for 4 h, the crystalline phases identified by XRD were lithium silicate (Li₂SiO₃), β-wollastonite (β-CaSiO₃), lithium orthophosphate (Li₃PO₄), magnetite (FeFe₂O₄) and triphylite (Li(Mn_0.5Fe_0.5)PO₄). The SEM surface analysis revealed that the β-wollastonite and lithium silicate have a lath morphology. The TEM microstructure examination showed that the largest FeFe₂O₃ particles have a size of approximately 0.3 μm. When the 10LFS glass was heat treated at 850 °C for 16 h and a magnetic field of 1000 Oe was applied, a very small remnant magnetic induction of 0.01 emu g⁻¹ and a coercive force of 50 Oe were obtained, which revealed an inverse spinel structure.     

Structural and dielectric properties of Li2O–ZnO–BaO–B2O3–CuO glasses

Glass samples of the system (15Li₂O–30ZnO–10BaO–(45 − x)B₂O₃–xCuO where x = 0, 5, 10 and 15 mol%) were prepared by using the melt quenching technique. A number of studies, viz. density, differential thermal analysis, FT-IR spectra, a.c. conductivity and dielectric properties (constant εφ, loss tan δ, a.c. conductivity, σ_ac, over a wide range of frequency and temperature) of these glasses were carried out as a function of copper ion concentration. The analysis of the results indicate that the density increases while molar volume decreases with increasing of copper content indicates structural changes of the glass matrix. The glass transition temperature, T _g, and crystallization temperature, T _c, increase with the variation of concentration of CuO referred to the growth in the network connectivity in this concentration range, while glass-forming ability parameter (T _c − T _g) decreases with increasing CuO content, indicates an increasing concentration of copper ions that take part in the network-modifying positions. The FT-IR spectra evidenced that the main structural units are BO₃, BO₄, and ZnO₄. The structural changes observed by varying the CuO content in these glasses and evidenced by FTIR investigation suggest that the CuO plays a network modifier role in these glasses while ZnO plays the role of network formers. The dielectric constant decreased with increase in temperature and CuO content. The variation of a.c. conductivity with the concentration of CuO passes through a maximum at 5 mol%. In the high temperature region, the a.c. conduction seems to be connected with the mixed conduction viz., electronic conduction and ionic conduction.     

Low-temperature sintering and microwave dielectric properties of 5Li2O–0.58Nb2O5–3.23TiO2 ceramics

The effect of B₂O₃ addition on the sintering, microstructure and the microwave dielectric properties of the 5Li₂O–0.58Nb₂O₅–3.23TiO₂ (LNT) ceramics have been investigated. It is found that the LNT ceramics could be sintered well at ∼880 °C with low-level doping of B₂O₃ (≤2 wt.%). Only Li₂TiO₃ solid solution (Li₂TiO₃ss) crystal structure could be detected for all the ceramics with various amounts of B₂O₃ addition from the X-ray diffraction (XRD) results. And interestingly, two phases with different color in SEM images are observed in B₂O₃-doped LNT ceramics. EDS results suggest that the two different phases are two Li₂TiO₃ss phases with different amount of Nb. In addition, there is no much degradation in the microwave dielectric properties with the B₂O₃ adding. In the case of 0.5 wt.% B₂O₃-doped samples sintered at 880 °C, good microwave dielectric properties of ?_r = 22, Q × f = 32,000 GHz, τ_f = 9.5 ppm °C⁻¹ are obtained.     

Densification and dielectric properties of SrO–Al2O3–B2O3 ceramic bodies

The influence of SrO (0·0–5·0 wt%) on partial substitution of alpha alumina (corundum) in ceramic composition (95 Al₂O₃–5B₂O₃) have been studied by co-precipitated process and their phase composition, microstructure, microchemistry and microwave dielectric properties were studied. Phase composition was revealed by XRD, while microstructure and microchemistry were investigated by electron-probe microanalysis (EPMA). The dielectric properties by means of dielectric constant (ε _r ), quality factor (Q × f) and temperature coefficient of resonant frequency (τ _f ) were measured in the microwave frequency region using a network analyser by the resonance method. The addition of B₂O₃ and SrO significantly reduced the sintering temperature of alumina ceramic bodies to 1600 °C with optimum density (∼ 4g/cm³) as compared with pure alumina powders recycled from Al dross (3·55g/cm³ sintered at 1700 °C).     

Highlighting of structural units of B2O3–Li2O–P2O5 system under heat treatment

As technology evolves towards the design of small size – high efficiency devices there is a necessity for the development of solid, stable electrolytes that can be fabricated in various shapes. Accordingly, a glass system of xB₂O₃·0.4Li₂O·(0.6 − x)P₂O₅ with 0 ≤ x ≤ 0.6 mol%, was prepared by melting the raw materials at 1200 °C and rapidly cooling the melts at room temperature. The samples were afterwards heat treated to develop crystalline structures, for better identification of the units that build up the network.     

Characterisation of thermo-mechanical properties of MgO–Al2O3–SiO2 glass ceramic with different heat treatment temperatures

The effects of heat treatment temperature on crystallisation behaviour, precipitated phases and thermo-mechanical properties of some MgO–Al₂O₃–SiO₂ (MAS) glass-ceramics were investigated. Crystallisation behaviour of MgO–Al₂O₃–SiO₂ glasses in the presence of TiO₂ as a nucleation agent was studied. The crystalline phases present in the heat treated samples were identified by X-ray diffraction (XRD). It was observed from XRD studies that magnesium aluminium titanate initially precipitated and when the heat treatment temperature was increased to 1140 °C, depending on the thermal history, either magnesium silicate, aluminium titanate and quartz or magnesium aluminium titanate, magnesium aluminate and quartz were precipitated. SEM observation revealed that the heat treatment led to phase separation of droplet-shaped crystals before the needle-shaped crystals formed at 1140 °C. The effect of annealing temperature on the density and mechanical properties of these glass-ceramic were characterised by nanoindentation and the results revealed a significant increase in hardness of the fully crystallised system.     

Effects of copper and Al2O3 particles on characteristics of Cu–Al2O3 composites

High-energy milling was used for production of Cu–Al₂O₃ composites. The inert gas-atomized prealloyed copper powder containing 2 wt.%Al and the mixture of the different sized electrolytic copper powders with 4 wt.% commercial Al₂O₃ powders served as starting materials. Milling of prealloyed copper powders promotes formation of nano-sized Al₂O₃ particles by internal oxidation with oxygen from air. Hot-pressed compacts of composites obtained from 5 and 20 h milled powders were additionally subjected to the high-temperature exposure in argon at 800 °C for 1 and 5 h. Characterization of processed material was performed by optical and scanning electron microscopy (SEM), X-ray diffraction analysis (XRD), microhardness, as well as density and electrical conductivity measurements. Due to nano-sized Al₂O₃ particles microhardness and thermal stability of composite processed from milled prealloyed powders are higher than corresponding properties of composites processed from the milled powder mixtures. The results were discussed in terms of the effects of different size of starting copper powders and Al₂O₃ particles on the structure, strengthening of copper matrix, thermal stability and electrical conductivity of Cu–Al₂O₃ composites.     

Li2O·Al2O3·4SiO2-Ta2O5系微晶玻璃分相与析晶机理研究

采用Ta2O5为晶核剂制备Li2O.Al2O3.4SiO2-Ta2O5微晶玻璃,并研究其分相、析晶机理,构建晶化模型.结果表明Ta2O5能有效促进玻璃的体积析晶,获得了晶粒尺寸为50nm的精细组织.非等温动力学计算显示随Ta2O5含量增加,析晶活化能降低,析晶指数增加,析晶动力学参数K(Tp)作为析晶判据更为合理.研究发现,LAST玻璃冷却时因亚稳分解导致互锁分相,形核前期又借助成核生长机制发生微滴分相,晶体生长则在继承亚稳分相形貌基础上发生"他形"析晶.最终构建了LAST微晶玻璃的晶化模型.     

Wetting and interfacial interactions in the CaO–Al2O3–SiO2/silicon carbide system

In this article, the wetting of 23 wt% CaO–15 wt% Al₂O₃–62 wt% SiO₂ molten glass on polycrystalline silicon carbide is studied under air at temperatures between 1,100 and 1,590 °C. Wetting experiments are performed by the sessile drop technique. Good wetting (final contact angle lower than 50°) is observed regardless of the experimental temperature when it is higher than 1,300 °C. Moreover, some specific experiments of wetting of glass on platinum, silica and monocrystalline SiC substrates are also performed. The character of molten glass spreading on silicon carbide (reactive or non-reactive) as well as the role of the atmosphere on interfacial interactions with SiC are identified and discussed.     

Synthesis and properties of glasses in the K2O–SiO2–Bi2O3–TiO2 system and bismuth titanate (Bi4Ti3O12) nano glass–ceramics thereof

Glasses were prepared by the melt-quench technique in the K₂O–SiO₂–Bi₂O₃–TiO₂ (KSBT) system and crystallized bismuth titanate, BiT (Bi₄Ti₃O₁₂) phase in it by controlled heat-treatment at various temperature and duration. Different physical, thermal, optical, and third-order susceptibility (χ³) of the glasses were evaluated and correlated with their composition. Systematic increase in refractive index (n) and χ³ with increase in BiT content is attributed to the combined effects of high polarization and ionic refraction of bismuth and titanium ions. Microstructural evaluation by FESEM shows the formation of polycrystalline spherical particles of 70–90 nm along with nano-rods of average diameter of 85–90 nm after prolonged heat treatment. A minor increase in dielectric constants (ε_r) has been observed with increase in polarizable components of BiT in the glasses, whereas a sharp increase in ε_r in glass–ceramics is found to be caused by the formation of non-centrosymmetric and ferroelectric BiT nanocrystals in the glass matrix.     

Microstructures formed during devitrification of Na2O·Al2O3·B2O3·SiO2·Fe2O3 glasses

Soda alumina borosilicate glasses of composition (24-y)Na₂O·yAl₂O₃·14B₂O₃·37SiO₂·25Fe₂O₃, y = 8, 12, 14, 16 mol%, were melted using Fe₂O₃ as raw material. Besides, samples with y = 12 and Fe₂O₃ concentrations of 14.32, 17.8, and 25.0 mol% were prepared from FeC₂O₄·2H₂O as raw material. The X-ray diffraction analyses showed the presence of magnetite for the samples from all the investigated compositions. Transmission electron microscopy (TEM) evidenced that all the samples are phase separated and droplets in the diameter range 100–1000 nm, enriched in iron, are formed. Inside these droplets, numerous small magnetite particles, with size in the 25–40 nm interval, are crystallized.     

Thermal properties and crystallization of PbO–MoO3–P2O5 glasses

Thermal properties and crystallization of glasses from PbO–MoO₃–P₂O₅ ternary system were studied in three compositional series (100 − x)[0.5PbO–0.5P₂O₅]–xMoO₃ (A), 50PbO–yMoO₃–(50 − y)P₂O₅ (B), and (50 − z)PbO–zMoO₃–50P₂O₅ (C). Glass transition temperature, crystallization temperature, coefficient of thermal expansion, and dilatation softening temperature of the studied glasses were determined by differential thermal analysis and dilatometry. Crystallization products of annealed glass samples were investigated by X-ray diffraction and Raman spectroscopy. X-ray diffraction analysis of crystallized glasses revealed the formation of PbP₂O₆, Pb₃P₄O₁₃, and PbMoO₄ in the samples of the B series. In the series A and C in the samples with a high MoO₃ content, crystalline compounds of Pb(MoO₂)₂(PO₄)₂ and (MoO₂)(PO₃)₂, respectively, were identified. Raman spectra of crystalline samples confirmed the results of X-ray diffraction measurements and provided also information on thermal stability of glasses and formation of glass-crystalline phases in the studied glass series.     

The phase transformation and crystallization kinetics of (1 − x)Li2O–xNa2O–Al2O3–4SiO2 glasses

The phase transformation and crystallization kinetics of (1 − x)Li₂O–xNa₂O–Al₂O₃–4SiO₂ glasses have been studied by using differential thermal analysis (DTA), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electron diffraction (ED) analysis. The crystallization temperature at the exothermic peak increases from 1171 to 1212 K when the Na₂O content increases from 0 to 0.6 mol. The crystalline phase is composed of spodumene crystallization when the Na₂O content increases from 0 to 0.6 mol. The activation energy of spodumene crystallization decreases from 444.0 ± 22.2 to 284.0 ± 10.8 kJ mol⁻¹ when the Na₂O content increases from 0 to 0.4 mol. Moreover, the activation energy increases from 284.0 ± 10.8 to 446.0 ± 23.2 kJ mol⁻¹ when the Na₂O content increases from 0.4 to 0.6 mol. The crystallization parameters m and n approach 2, indicating that the surface nucleation and two-dimensional growth are dominant in (1 − x)Li₂O–xNa₂O–Al₂O₃–4SiO₂ glasses.     

纳米Y2O3:Eu3+粉体的表面包膜处理

本文采用高分子网络凝胶法制备了粒径约为20nm的纳米Y     

Relaxation process in PbI2–Ag2O–V2O5–B2O3 system: Dielectric,AC conductivity and modulus studies

Silver ion conducting super-ionic glass system xPbI₂–(100 − x) [Ag₂O–2(V₂O₅–B₂O₃)], where, 5 ≤ x ≤ 25, were prepared via melt quenching route and -characterized by XRD and DSC. Their electrical properties were measured by impedance spectroscopy in the frequency range of 2 MHz to 20 Hz from 30 to 120 °C. The electrical relaxation mechanism has been studied using AC conductivity, dielectric modulus function and frequency dependent dielectric permittivity over a wide range of frequency and temperature. Two different scaling approaches for AC conductivity as well as dielectric permittivity spectra were used to understand the nature of relaxation processes.     

Sol–gel derived CaO–B2O3–SiO2 glass/CaSiO3 ceramic composites: processing and electrical properties

The CaO–B₂O₃–SiO₂ glass/CaSiO₃ ceramic (CBS/CS) composites were fabricated via sol–gel processing routes. Their densification behavior, structures and dielectric properties were investigated. The precursors of CBS glass and CS ceramic filler were firstly obtained via individual soft chemical route and then mixed together in various proportions. The results indicated that the structures of CBS/CS composites are characteristic of CS and CaB₂O₄ (CB) ceramic phases distributed in the matrix of glass phase at 800–950 °C. The CS ceramic phase not only acts as fillers, but nuclei for the crystallization of CBS glass as well such that the CS content exhibits an effect on the densification and dielectric properties of the composites. The CBS/CS composites with 10% CS sintered at 850 °C own dielectric properties of ε_r < 5 and tanδ = 6.4 × 10⁻⁴ at 1 MHz.     

多孔Al2O3f/Al2O3复合材料研究进展

作为20世纪90年代兴起的一类连续陶瓷纤维增强陶瓷基复合材料,连续氧化铝纤维增韧氧化铝(Al₂O_3f/Al₂O₃)复合材料已经发展为与C_f/SiC、SiC_f/SiC等非氧化物复合材料并列的陶瓷基复合材料。以多孔基体实现基体裂纹偏转成为Al₂O_3f/Al₂O₃复合材料主要的增韧设计方法,形成的多孔Al₂O_3f/Al₂O₃复合材料具有优异的抗氧化性能和高温力学性能,可在高温富氧、富含水汽的中等载荷工况中长时服役,是未来重要的热结构材料。经过近30年的发展,多孔Al₂O_3f/Al₂O₃复合材料已被应用于航空发动机、燃气轮机等热端部件。本文综述了多孔Al₂O_3f...     

SrAl2O4:Eu2+,Dy3+时间分辨手印成像研究

研究了以铝酸锶为基质,Eu2+和Dy3+共掺杂的长余辉粉体(SED)光学性质,将长余辉粉体与铁粉混合,用于刷显不同客体上的潜在手印,采集了手印发光图像,与普通荧光粉进行了手印显现、成像对比研究。实验结果表明,长余辉粉体适用于非渗透性和半渗透性客体上的手印显现,其超长余辉性质,可以消除(降低)背景干扰,有助于实现背景图案复杂客体上的手印时间分辨成像。     

SiO2对Al2O3凝胶纤维相变的影响

以尿素催化硅酸乙酯水解制得SiO2溶胶。采用29Si NMR、27 Al NMR、FT-IR、TEM、DTA、XRD和SEM等对SiO2溶胶、Al2O3凝胶纤维化学结构和微观结构研究结果表明,该SiO2溶胶稳定性好,含有大量的单硅酸Si(OH)4,能和Al2O3表面的Al—OH反应生成Al—O—Si键而有效地将其包裹,从而阻止了过渡态Al2O3微晶的相互接触,抑制了α-Al2O3的成核和生长。