Catalytic reduction of NO by hydrocarbons over a mechanical mixture of spinel Ni–Ga oxide and manganese oxide

NO reduction with propylene over Mn₂O₃, spinel Ni–Ga oxide and their mechanical mixtures has been investigated. Mn₂O₃ has no activity to NO reduction, but has a high activity for NO oxidation to NO₂. Spinel Ni–Ga oxide showed an apparent activity to NO reduction only at temperatures above 400°C. Mixing of Mn₂O₃ to the Ni–Ga oxide resulted in a significant enhancement of NO reduction in the temperature range of 250–450°C. The optimal Mn₂O₃ content in the mixture catalyst was about 10–20 wt%. It is suggested that the synergetic effect of Mn₂O₃ and Ni–Ga oxide plays an important role in the catalysis of NO reduction. The Ni–Ga oxide and Mn₂O₃ mixture catalyst is superior to Pt/Al₂O₃ and Cu-ZSM-5 by showing a higher NO reduction conversion, resistance to water and negligible harmful by-product formation. Other lower hydrocarbons C₂H₄, C₂H₆ and C₃H₈ also give a maximum NO reduction conversion as high as 50%. The difference from using C₃H₆ is that the temperature at the maximum NO reduction is higher than it is with C₃H₆. This revised version was published online in July 2006 with corrections to the Cover Date.     

Preparation and characterisation of titania-supported vanadium–phosphorus oxide catalysts

A series of vanadium–phosphorus oxides (mainly with V P ) supported on pigmentary anatase (10 m² g^-1) has been prepared using aqueous NH₄VO₃ and (NH₄)H₂PO₄ solutions, with loadings up to 11.3 wt%, equivalent to about 12.7 monolayers. Characterisation by X-ray diffraction, laser Raman spectroscopy, X-ray photoelectron spectroscopy and temperature-programmed reduction suggests that the main phase present at loadings below about 10 wt% is an amorphous V–P oxide which exists chiefly as blocks of disordered material. The presence of small amounts of crystalline -VOPO₄ and of V₂O₅ is indicated at the highest loadings, especially when and V P ratios are used. The two materials having the lowest loadings are active for methanol oxidation at 473–533 K, and show high selectivity to formaldehyde. This revised version was published online in June 2006 with corrections to the Cover Date.     

Sono-assisted preparation of magnetic ferroferric oxide/graphene oxide nanoparticles and application on dye removal☆

A simple ultrasound-assisted co-precipitation method was developed to prepare ferroferric oxide/graphene oxide magnetic nanoparticles (Fe3O4/GO MNPs). The hysteresis loop of Fe3O4/GO MNPs demonstrated ...     

Copolymers of ε-caprolactam and polypropylene oxide via anionic polymerization: synthesis and properties

Copolymers with an elastic polypropylene oxide (PPO), middle block in the main chain of poly(ε-caprolactam) were synthesized via activated anionic ring opening polymerization of ε-caprolactam (CL) in the presence of a basic initiator sodium salt of CL (Na-CL) and effective bifunctional polymeric activators (PACs). By varyng the molecular weight, two types of PACs were synthesized based on carbamoyl derivatives of hydroxyl terminated PPO with isophorone diisocyanate and were blocked with CL. The formation of copolymers has been confirmed by proton nuclear magnetic resonance spectroscopy (¹H–NMR) and Fourier transform infrared spectroscopy (FT-IR). The influence of the molecular weight of the PACs, the CL/PAC ratio and polymerization conditions on the conversion, intrinsic viscosity and polymerization kinetics, was investigated. The calorimetric, wide-angle X-ray diffraction (WAXD), thermogravimetric analysis (TGA), notched impact test and dynamic mechanical thermal analysis (DMTA) were performed to estimate the influence of the composition ratio and the type of PACs on the physical, thermal, and mechanical properties of the copolymers. The use of the synthesized PACs reduced the polymerization time to several minutes. The copolymers showed improved impact resistance up to more than two times higher than those of the polyamide 6 (PA-6) homopolymer, without significant changes in their high melting temperatures.     

Effects of nanosilica and titanium oxide on the performance of epoxy–amine nanocoatings

Different types of composite coatings were prepared by the blending of colloidal nanosilica (SiO₂) and titanium dioxide (TiO₂) in epoxy resin to investigate their coating performances. A fixed amount of silica nanoparticles (20 wt %) and different amounts (5, 10, and 15 wt %) of microsized TiO₂ particles were used in the coatings. The functional groups of the formulated coatings were confirmed by Fourier transform infrared spectroscopy. These results indicate that the SiO₂–TiO₂ particles interacted well with epoxy. Scanning electron microscopy images of the composite coatings revealed a good dispersion of TiO₂ particles at a lower amount of loading; this improved the adhesiveness, glass-transition temperature, thermal stability, and chemical resistance properties. At higher loadings, the performances decreased. The composite coatings were also characterized by their UV radiation-absorption properties with an ultraviolet–visible spectrophotometer. Interestingly, this property was found to be enhanced at higher loadings. An impressive result was noticed in the nanocomposites in terms of oxygen transmission rate performance compared to that of the neat epoxy. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47901.     

Thermodynamic and kinetic studies of crystal violet dye adsorption with poly(methyl methacrylate)–graphene oxide and poly(methyl methacrylate)–graphene oxide–zinc oxide nanocomposites

We successfully prepared poly(methyl methacrylate) (PMMA)–graphene oxide (GO) and PMMA–GO–zinc oxide (ZnO) nanocomposites and characterized them using different techniques. The adsorption performances of the as-prepared composites were investigated for crystal violet (CV) dye removal. The contact time as a main factor affecting the adsorption process by adsorbents was studied. Because the adsorption capacity value for CV was found to show no extensive changes after 35 min, 35 min was selected as the best contact time for our system. The adsorption results revealed that the best capacity of CV adsorption onto the PMMA–GO and PMMA–GO–ZnO nanocomposites occurred at pH 12 and 298 K. The respective entropies (−0.208 and −0.168 kJ mol⁻¹ K⁻¹) and enthalpies (−72.86 kJ/mol, and −55.54 kJ/mol) for PMMA–GO and PMMA–GO–ZnO and Gibbs energy revealed that the process of adsorption was exothermic. In addition, the Elovich, pseudo-first-order, intraparticle diffusion, and pseudo-second-order (four types) models were applied to our kinetic study. Our results indicate that CV adsorption onto PMMA–GO and PMMA–GO–ZnO was good with the pseudo-second-order (type 1) and pseudo-first-order models because of the low χ² value and the high correlation coefficient value. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47495.     

Hydrostatic treatment of α-aluminium oxide powders part 1. Microstructure of the particles and sintering

Transmission electron microscopy and X-ray radiography are used to show that pressing of -aluminum oxide powders at pressures up to 2.0 GPa is accompanied by crushing of particles and the appearance of dislocations with a density of about 10¹¹ cm^–2. Sintering of these powders at temperatures up to 1550°C reduces the dislocation density 2–4-fold. When the compacts reach a critical density (about 62%) the shrinkage in sintering of nonsintered powders is shown to be independent of the compact density and the pore size. The increase in the sintering rate with increase in the hydrostatic pressure to 0.6 GPa is shown to be caused mainly by an increase in the compact density and at still higher pressures by the mechanical activation of the powders.Translated from Ogneupory, No. 6, pp. 13–19, June, 1994.     

Synthesis,characterization, and electrical properties of polypyrrole–bimetallic oxide composites

In this study, polypyrrole (PPy) and its bimetallic oxide composites (PPy–V₂O₅–MnO₂) were synthesized via a modified chemical oxidation polymerization method in the aqueous medium with FeCl₃·6H₂O as an oxidant. The synthesized materials were characterized with various analytical techniques to investigate their structural, crystallographic, thermal, morphological, optical, and electrical properties. The Fourier transform infrared study confirmed the successful synthesis of the materials, whereas the X-ray diffraction analyses showed the amorphous and crystalline natures of the PPy and PPy–V₂O₅–MnO₂ composites, respectively. The bimetallic oxide content improved the thermal stability of the composites, as ratified by thermal analysis. The synthesized PPy had a globular and spongy nature, whereas the composites were mixtures of short and long rod-shaped particles. The bimetallic oxide blend enhanced the doping, surface area and semiconducting nature of composites, and lower electrical resistance compared with those of the PPy. The resistance of the synthesized materials depended on the V₂O₅–MnO₂ blend content in the composites and the temperature. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 47680.     

Synthesis and enzymatic degradation of poly(ε-caprolactone-co-ethylene carbonate-co-ethylene oxide) copolymer

Poly(ε-caprolactone-co-ethylene carbonate-co-ethylene oxide) (CL-co-EC-co-EO) copolymer was synthesized via ring-opening copolymerization of ε-caprolactone (CL) and 1,3-dioxolan-2-one with a metal-free phosphazene catalyst (t-BuP₄). The monomer conversion and molecular weight in CL-co-EC-co-EO copolymer were characterized by nuclear magnetic resonance and gel permeation chromatography, respectively. Moreover crystallization behavior of CL-co-EC-co-EO copolymer was investigated by differential scanning calorimeter and wide-angle X-ray diffraction. The enzymatic degradation of the copolymer has been investigated by quartz crystal microbalance with dissipation. Our studies demonstrate that as PCL content in the copolymer decreases, the degree of crystallinity and crystal size decrease, while the enzymatic degradation rate increases. The copolymer exhibits layer-by-layer degradation.     

Modification of poly(vinylidene fluoride) membranes with aluminum oxide nanowires and graphene oxide nanosheets for oil–water separation

To improve the hydrophilic and oleophobic properties of membrane, we adopted aluminum oxide (Al₂O₃) nanowires and graphene oxide (GO) nanosheets to modify poly(vinylidene fluoride) (PVDF) membranes. The experimental results show that the intercalation of Al₂O₃ nanowires between GO nanosheets effectively improved the roughness of the GO–Al₂O₃–PVDF membrane, and the permeability of the membrane with an optimal mass ratio of Al₂O₃ to GO of 7.5 was 31 times that of the GO–PVDF membrane. Furthermore, the addition of Al₂O₃ nanowires significantly enhanced both the hydrophilic and oleophobic properties of the GO–Al₂O₃–PVDF membrane. On the basis of the extended Derjaguin–Landau–Verwey–Overbeek theory, the energy barriers between the oil droplets and GO–PVDF and GO–Al₂O₃–PVDF membranes were 0.63 and 0.9 KT, respectively; this indicated improvements in the anti-oil-fouling ability of the GO–Al₂O₃–PVDF membranes. We also found that both the GO–PVDF and GO–Al₂O₃–PVDF membranes had great oil–water separation rates (97.9 and 99.4%, respectively) with an initial oil concentration of 200 mg/L. The findings of this study show that the GO–Al₂O₃–PVDF membrane is a promising oil–water separation membrane, and further investigation of the cleaning procedure is needed to promote its practical application in oil–water separation. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47493.     

Effect of processing on the stability and electrical properties of pressureless sintered graphene oxide–alumina composites

This paper explores the processing of an alumina matrix composite with a percolating network of graphene oxide (GPO), which exhibits a moderate electric resistivity and a near zero temperature coefficient of resistance. Different formulations of GPO–alumina composites were processed using a water–base blending, and, the pellets were densified by pressureless sintering under Argon flow. Electrical conduction at room temperature was achieved in the 2 wt % GPO–alumina composite sintered at 1400 °C, and, the 3 wt % GPO–alumina composites sintered at 1400, 1550 and 1700 °C. An investigation of the degradation of electrical conductivity was used to identify potential stable operating regimes in which these materials could be used as heaters. Thermogravimetric analysis using the Ozawa–Flynn–Wall method, was used to determine the kinetic parameters of a 3 wt % GPO composite sintered at 1400 °C which, had an activation energy for GPO degradation of 195 ± 68 kJ/mol and, an estimated thermal lifetime of 8.7 ± 0.8 years for a conversion of 0.5 wt % (failure criterion) at an application temperature of 340 °C.     

Preparation and characterization of phosphine oxide containing organosilica hybrid coatings by photopolymerization and sol–gel process

A series of UV-cured organic–inorganic hybrid coating materials containing up to 20 wt.% silica were prepared by sol–gel method from tetraethoxy silane (TEOS) which is used as the primary inorganic precursor, and diallylphenylphosphine oxide monomer (DAPPO), aliphatic urethane diacrylate resin (Ebecryl 210) are employed as the source of the organic components. In addition, methacryloxypropyltrimethoxy silane (MAPTMS) was used as both a secondary inorganic source and a silane-coupling agent to improve the compatibility of the organic and inorganic phases. The DAPPO content in all the coating formulations were from 0 to 20 wt.%. The physical and mechanical properties such as gel content, hardness, adhesion, gloss, contact angle as well as tensile strength were measured. These measurements revealed that all the properties of the hybrid coatings improved effectively, in case of adding the sol–gel precursor and DAPPO monomer content in the hybrid systems. The photo-calorimetric-DSC studies showed that the double bond conversion of the hybrid coatings was faster than the coating materials without silica. The thermal stabilities of the UV-cured hybrid materials were investigated by thermogravimetric analysis. The results showed that the addition of sol–gel precursor and DAPPO into the organic network also improves the thermal-oxidative stability of the hybrid coating materials. The surface morphology was also characterized by scanning electron microscopy (SEM). SEM studies indicated that inorganic particles were dispersed homogenously throughout the organic matrix.     

Microstructure of single-phase cobalt and manganese oxide spinel Mn3−xCoxO4 ceramics

This paper reports microstructural studies of single-phase Mn_3−xCo_xO₄ (0.98 ≤ x ≤ 2.93) spinel ceramics using transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDX). These ceramics were obtained by conventional sintering or by spark plasma sintering (SPS) of powders prepared by thermal decomposition of coprecipitated oxalate precursors. For x < 1.78 or x ≥ 1.78, the monophasic ceramics correspond respectively to quadratic (Q) or cubic (C) spinel structure. The ferroelastic character of the structural phase transition from C to Q is highlighted by specific microstructural features. The effect of chemical composition and heat treatment conditions on the microstructure and essentially on the presence and the characteristics of twins were investigated. The coherent twin interfaces are parallel to (1 1 2) planes in the Q cell. Twins can correspond to: tweeds, single lamellae (widths: 5–306 nm) arranged parallel to each other, large lamellae (widths: 69–928 nm) internally twinned and sometimes arranged in cyclic forms (triangular shapes).     

Synthesis and characterization of aluminum oxide–boron carbide coatings by air plasma spraying

Aluminum oxide (Al₂O₃)–boron carbide (B₄C) composites have been proposed for use as cutting tools as well as in high temperature applications due to their high hardness and fracture toughness. The air plasma spraying method was used to fabricate the composite coatings of Al₂O₃ and B₄C. Three different Al₂O₃:B₄C composition ratios of 90:10, 80:20, and 70:30 by weight were plasma sprayed on plain carbon steel substrates. The effect of B₄C content on microstructure, hardness, porosity and thermal diffusivity of the coatings were studied using scanning electron microscopy (SEM), microhardness testing, X-ray diffraction (XRD), and the flash diffusivity method. The plasma spray parameters were optimized in order to achieve a theoretical density of approximately 90%.     

Mechanochemical synthesis of zinc ferrite from zinc oxide and α-Fe2O3

Mechanochemical synthesis of zinc ferrite (ZnFe₂O₄) from a powder mixture of zinc oxide (ZnO) and hematite (α-Fe₂O₃) by room temperature grinding using a planetary ball mill was investigated. The grinding enables us to obtain the amorphous mixture of the starting materials. Most of ZnO reacts with α-Fe₂O₃ to convert into insoluble amorphous zinc and iron compounds within 2h-grinding. Prolonged grinding enhances the crystallization of ZnFe₂O₄ from the amorphous compounds. ZnFe₂O₄ crystallized by the grinding for 3 h or more consists of nanocrystalline particles with high specific surface area.     

Direct multipulse laser processing of titanium oxide–graphene oxide nanocomposite thin films

Nanocomposite thin films consisting of titanium oxide (TiO₂) nanoparticles (NPs) and graphene oxide (GO) platelets were deposited by a spin-coating technique. The obtained films were submitted to direct laser irradiation using a frequency quadrupled Nd:YAG (λ=266 nm, τ_FWHM≅3 ns, ν=10 Hz) laser source. The effect of the laser processing conditions, as laser fluence value and number of subsequent laser pulses incident onto the same target location, on the surface morphology, crystalline structure, and chemical composition of the TiO₂/GO nanocomposite thin films was systematically investigated. The laser fluence values were maintained below the vaporization threshold of the irradiated composite material. With the increase of the laser fluence and number of incident laser pulses melting and coalescence of the TiO₂ NPs into inter-connected aggregates as well as rippling of the GO platelets take place. The gradual reduction of GO platelets and the onset of anatase to rutile phase transition were observed at high laser fluence values.     

Physico-chemical and catalytic properties of Mg–Al hydrotalcite and Mg–Al mixed oxide supported copper catalysts

The Mg–Al hydrotalcite (HT) and Mg–Al mixed oxide supported copper catalysts containing 3–3.5 wt.% copper in finely dispersed form were synthesized and characterized. The effect of support nature on physico-chemical and catalytic properties of supported copper species were studied. The loading of copper on the supports was observed to be influencing the surface acidic, basic and reducibility properties, and catalytic behavior in dehydrogenation of benzyl alcohol. The high basicity and intercalated copper ions in Mg–Al hydrotalcite supported copper sample showed multifunctional activity in catalytic transformations of alcohols (primary, secondary and aromatic alcohols).     

Synthesis,mechanical property,and thermal stability of reduced graphene oxide–zinc oxide/cyanate ester/bismaleimide resin composites

Reduced graphene oxide–zinc oxide/cyanate ester/bismaleimide resin (RGO–ZnO/CE/BMI) composites were synthesized via a blending method. The RGO–ZnO composite was incorporated into the CE/BMI copolymer to improve the properties of RGO–ZnO/CE/BMI composites. The structure, elements, and morphology of the RGO–ZnO composite were studied with XPS, FTIR, XRD, and SEM analyses. It indicated that the ZnO micro-sphere was attached to RGO by electrostatic attraction and the RGO–ZnO composite was prepared successfully. The mechanical properties and thermal stability of RGO–ZnO/CE/BMI composites were investigated. When RGO–ZnO composite was 1 wt.%, the flexural and impact strengths of RGO–ZnO/CE/BMI composites were 1.07 and 1.35 times of the CE/BMI copolymer, respectively. However, the RGO–ZnO composite tended to aggregate in the CE/BMI matrix with high loading. According to the SEM analysis, appropriate RGO–ZnO composite was evenly dispersed in the CE/BMI copolymer. Compared to the CE/BMI copolymer, the thermal stability of the RGO–ZnO/CE/BMI composites was good. Thus, the RGO–ZnO composite was successfully filled in the CE/BMI matrix; the mechanical properties and thermal stability of the RGO–ZnO/CE/BMI composites were enhanced.     

Young’s modulus evolution during sintering and thermal cycling of pure tin oxide ceramics

Pure tin oxide (SnO₂) ceramics is well known for its bad sinterability, more precisely for the difficulty to densify without additives by conventional pressureless sintering. This is related to the fact that the sintering mechanisms in pure tin oxide ceramics are non-densifying (surface diffusion at low temperature and evaporation-condensation at high temperature). On the other hand, for the same reason, pure tin oxide ceramics is a very unusual model system that can be used to demonstrate the effects of microstructural changes on effective properties without the otherwise dominating effect of changes in porosity. In this paper we show that pure tin oxide ceramics uniaxially pressed at 50 MPa, pre-sintered at 500 °C and re-sintered at 1000, 1200 and 1400 °C exhibit relative Young’s modulus increases of 30, 70 and 120 % while the porosity remains essentially constant at a value of 51.6 ± 0.7 %.