双马来酰亚胺/环氧树脂/纳米SiO2复合材料的制备与性能研究

研究了纳米二氧化硅（SiO2）的含量对双马来酰亚胺（BMI）/环氧树脂(EP)/2,2′二烯丙基双酚A(DBA)/纳米SiO2复合材料的耐热性能、力学性能和吸水性能的影响。结果表明,当纳米SiO2的含量为2.0 %(质量分数,下同)时,BMI/EP/DBA/纳米SiO2复合材料具有较高的强度和良好的韧性,其拉伸强度、弯曲强度和缺口冲击强度比BMI/EP/DBA复合材料分别提高了22.8 %、39.0 %和37.8 %;同时,纳米SiO2含量为 2.0 %时,BMI/EP/DBA/纳米SiO2复合材料具有优异的耐热性,其玻璃化转变温度、初始热分解温度和最大热分解温度分别为204、 410、451 ℃。     

改性氰酸酯类耐高温胶粘剂的研究

以双马来酰亚胺(BMI)、双酚A型氰酸酯(BADCy)和苯并噁嗪(BOZ)树脂为基体树脂,纳米二氧化硅(nano-SiO2)为填料,制备耐高温胶粘剂。采用非等温差示扫描量热(DSC)法、Kissinger法和Ozawa法研究了nano-SiO2/BOZ/BMI/BADCy共聚物的固化动力学过程。结果表明:当m(BOZ)∶m(BMI)∶m(BADCy)=1∶1∶2、w(nano-SiO2)=3%时,相应BOZ/BMI/BADCy胶粘剂的表观活化能(47.82 kJ/mol)低于无nano-SiO2体系(59.17 kJ/mol),并具有良好的耐高温性能;在250℃时用该胶粘剂胶接硅钢片,胶接件经250℃老化1 000 h后,其剪切强度仍保持稳定。     

GNS/BOZ/EP复合材料的合成及性能研究

采用氧化-还原法制备了石墨烯纳米片(GNS);然后将GNS加入到苯并噁嗪(BOZ)/环氧树脂(EP)体系中,制成了GNS/BOZ/EP复合材料。采用红外光谱(FT-IR)、透射电镜(TEM)和X射线衍射(XRD)法等对所得GNS的结构进行了表征和分析,同时研究了复合材料的力学性能和耐热性。研究结果表明:GNS能提高BOZ/EP体系的力学性能和耐热性;当w(GNS)=0.2%(相对于复合材料总质量而言)时,GNS/BOZ/EP体系的综合性能相对最优,其冲击强度(14.2 k J/m2)比BOZ/EP体系提高了14.5%左右,弯曲强度达到了139 MPa,最初热分解温度和最大热分解温度(分别为299.7、353.4℃)均有所提高。     

聚甲醛/纳米SiO2复合材料的力学性能、结晶行为及热稳定性研究

以改性纳米SiO2为填料,通过熔融共混工艺制备聚甲醛/纳米SiO2复合材料,对其力学性能、结晶行为及热稳定性进行了研究。结果表明:复合材料的拉伸强度和缺口冲击强度随着SiO2含量的增加呈先增大后减小的趋势,二者分别在SiO2质量分数为3%和1%时达到最大;而弹性模量的情况则有所不同,其随着SiO2含量的增加不断增大。DSC测试结果显示,纳米SiO2具有较好的形核作用,能够促进聚甲醛的结晶温度升高,但会抑制晶粒的生长,导致复合材料结晶度的降低。此外,纳米SiO2还能显著提高聚甲醛的热稳定性。与纯聚甲醛相比,复合材料的最大热分解温度在氮气和空气气氛下分别提高了约41.1℃和24.5℃。     

CE／纳米SiO2复合材料的力学性能和耐磨性研究

采用模塑成型法制备了不同配比的氰酸酯树脂(CE)/纳米SiO2复合材料,通过力学性能测试、磨损率测试和扫描电子显微镜(SEM)表征,发现纳米SiO2对复合材料的力学性能和耐磨性具有显著的协同改性作用.相对纯CE而言,当纳米SiO2经偶联荆SEA-171表面处理后,且其质量分数为3.0%时,CE/纳米SiO2复合材料的缺口冲击强度提高了83.58%,弯曲强度提高了18.42%,耐磨性提高了77%.     

偶联剂对SiO_2/CE复合材料热学及摩擦性能的影响

利用纳米SiO2对氰酸酯树脂(CE)进行改性,通过热失重分析(TGA)、摩擦磨损性能测试及扫描电镜(SEM)分析研究了纳米SiO2及其表面处理(分别选用小分子偶联剂KH-560和大分子偶联剂SEA-171)对纳米SiO2/CE复合材料热学及摩擦性能的影响,并初步探讨了其作用机理。结果表明,经SEA-171表面处理的纳米SiO2质量分数为3.0%时,其CE复合材料的热分解温度比纯CE树脂提高了将近75℃,摩擦系数降低了约25%,磨损率降低了77%。偶联剂的加入增加了纳米SiO2与CE树脂之间的界面粘结作用,因而复合材料的耐热性能和摩擦性能等得以提高。     

聚氨酯弹性体/纳米SiO2复合材料的力学性能研究

采用预聚体的方法制备了聚氨酯弹性体(PUE)/纳米SiO2复合材料,通过AJ(OH)3对纳米SiO2表面改性以及超声波分散的方法来提高纳米SiO2在PUE基体中的分散性,并考查了表面处理前后的纳米SiO2对PUE/纳米SiO2复合材料力学性能的影响.结果表明:改性后的纳米SiO2能均匀分散于PUE基体中,复合材料的力学性能明显提高;纳米SiO2的用量对PUE/纳米SiO2复合材料的力学性能影响较大,并且当纳米SiO2的质量分数为2%和3%时,复合材料的拉伸强度和撕裂强度分别达到最大.     

原位聚合抗磨损PA6/纳米SiO2复合材料制备及其性能研究

为提高聚酰胺6（PA6）的抗磨损性能,采用原位聚合法合成并制备了PA6/纳米SiO2复合材料,研究了该材料的抗磨损性能、耐热性能、力学性能和结晶性能。结果表明,原位聚合PA6/纳米SiO2复合材料具有良好的抗磨损特性,当纳米SiO2含量为1 %(质量分数,下同)时,复合材料抗磨损性能最佳,该材料的热变形温度、拉伸强度、弹性模量和断裂伸长率均明显高于原料PA6;当纳米SiO2含量为3 %时,复合材料热变形温度由原料PA6的64.6 ℃提高到130 ℃。采用原位聚合母料法制备的PA6/纳米SiO2复合材料同样具有理想的抗磨损性能,并可获得更好的力学性能,且可大幅降低材料制备成本。     

硅烷接枝HDPE/纳米SiO_2复合材料的制备与性能

将经表面处理后的纳米SiO2和硅烷接枝高密度聚乙烯(HDPE)熔融共混制得硅烷接枝HDPE/纳米SiO2复合材料,并对其结晶行为、力学性能及热性能进行了研究。结果表明:与HDPE相比,硅烷接枝HDPE/纳米SiO2复合材料的结晶度降低约17%;在纳米粒子含量为6%时,热分解温度提高了15℃;在纳米粒子含量为10%时,体系的拉伸强度提高了25%。     

尼龙11/蒙脱土纳米复合材料形态和性能研究

通过熔融共混法成功地制备了不同含量蒙脱土的尼龙11/蒙脱土纳米复合材料,利用X衍射(XRD)和透射电镜(TEM)研究了尼龙11/蒙脱土纳米复合材料的微观结构。结果表明,当蒙脱土质量分数小于2%时,形成了剥离型的纳米复合材料,当蒙脱土质量分数超过2%时形成了插层型的纳米复合材料。热重分析表明当蒙脱土质量分数为2%时,纳米复合材料的热分解温度比纯尼龙11提高了27℃。不同蒙脱土含量的纳米复合材料悬臂梁冲击强度均比纯尼龙11的高,但其拉伸强度在蒙脱土质量分数小于8%时降低,以后随蒙脱土含量的增加而提高。     

Preparation and properties of poly(Nε,Nε-dicarboxymethyl-l-lysine)

A new ampholytic homopolypeptide, $\text{poly}\text{(N}{}^{\mathrm{\epsilon }}\text{,N}{}^{\mathrm{\epsilon }}\text{-}\text{dicarboxy-methyl-}\text{l}\text{-lysine}\text{)}$, which has one tertiary amino and two carboxyl groups in the side chain has been derived from a hydrochloride salt of poly(L-lysine). The polymer in aqueous solution seems to be in the coil form with locally extended structure (LES) at neutral pH. In both the acidic and alkaline regions, the molar ellipticity of the polymer changes as a result of change in net charge on the side chain. The conformational changes may be from the coil with LES to other coiled forms. 5–7 M NaClO₄ and 80% aqueous methanol induce the α-helix in the polymer at neutral pH. Divalent cations, Cu²⁺ and Ca²⁺, do not induce any remarkably ordered structures such as α-helix or β-structure in the polymer in aqueous solution at any pH. Ultraviolet absorption studies show an absorption peak of the polymer-Cu²⁺ complex near 240 nm. Dependence of the peak intensity on pH at various q values ($\text{q =}\text{[}\text{Cu}{}^{\mathrm{2+}}\text{]}\text{[}\text{residue}\text{]}$) indicates the two steps of the complex formation. At q less than 0.64, the formation is described only with the first step. An average coordination number for Cu²⁺ at the first step was calculated to be about 2 by the method of Mandel and Leyte. The association constant of Cu²⁺ with the residue at the step was determined from the absorption data to be far smaller than that for the Cu²⁺-EDTA complex. The second step of the formation occurs in the case of large q but the absorption data for the second step cannot be obtained exactly due to precipitation.     

Wet Milling of Fe/Al/Al2O3 and Fe2O3/Al/Al2O3 Powder Mixtures

Wet milling of Al₂O₃-aluminide alloy (3A) precursor powders in acetone has been investigated by milling Fe/Al/Al₂O₃ and Fe₂O₃/Al/Al₂O₃ powder mixtures. The influence of the milling process on the physical and chemical properties of the milled powders has been studied. Particle refinement and homogenization were found not to play a dominant role, whereas plastic deformation of the metal particles leads to the formation of dislocations and a highly disarranged polycrystalline structure. Although no chemical reactions among the powder components in Fe₂O₃/Al/Al₂O₃ powder mixtures were observed, the formation of a nanocrystalline, ordered intermetallic FeAl phase in Fe/Al/Al₂O₃ powder mixtures caused by mechanical alloying was detected. Chemical reactions of Fe and Al particle surfaces with the atmosphere and the milling media lead to the formation of highly porous hydroxides on the particle surfaces. Hence the specific surface area of the powders increases, while the powder density decreases during milling. The fraction of Fe oxidized during milling was determined to be 0.13. The fraction of Al oxidized during milling strongly depends on the metal content of the powder mixture. It ranges between 0.4 and 0.8.     

Participation of lewis base on vinyl chloride polymerization with Al(C2H5)3CCl4 catalyst system

The polymerization of vinyl chloride has been investigated using an $\text{Al}\text{(}\text{C}{}_2\text{H}{}_5\text{)}{}_3\text{CCl}{}_4$ catalyst system in the presence of various Lewis bases. Effective Lewis bases are γ-butyrolactone, diglyme and diethylenetriamine which are multidentate. The rate of polymerization is dependent not only on the basicity of the Lewis base used but also on a coordination number of one. The latter is the predominant factor. For the effect of polymeric amines, a tentative hypothesis is discussed.     

Sintering of Si3N4-Y2O3-Al2O3

Sintering kinetics of the system Si₃N4-Y2O₃-Al₂O3 were determined from measurements of the linear shrinkage of pressed disks sintered isothermally at 1500° to 1700°C. Amorphous and crystalline Si₃N₄ were studied with additions of 4 to 17 wt% Y₂O₃ and 4 wt% A1₂O₃. Sintering occurs by a liquid-phase mechanism in which the kinetics exhibit the three stages predicted by Kingery's model. However, the rates during the second stage of the process are higher for all compositions than predicted by the model. X-ray data show the presence of several transient phases which, with sufficient heating, disappear leaving mixtures of β ' -Si₃N₄ and glass or β '-Si₃N₄, α '-Si₃N₄, and glass. The compositions and amounts of the residual glassy phases are estimated.     

Synthesis and Characterization of Ti0.33Ta0.33Nb0.33C and Ti0.33Ta0.33Nb0.33CxN1-x Whiskers

Ta_0.33Ti_0.33Nb_0.33C and Ta_0.33Ti_0.33Nb_0.33C _x N_{1− x} whiskers were synthesized via a carbothermal vapor-liquid-solid growth mechanism in the temperature range 900°-1450°C in Ar or N₂. The optimum temperature was 1250°C. Whiskers were obtained in a yield of 70-90 vol%. The whiskers were 0.5–1 µm in diameter and 10–30 µm in length. The starting materials that produced the highest whisker yield were: TiO₂, Ta₂O₅, Nb₂O₅, C, Ni, and NaCl. C was added to reduce the oxides, and Ni to catalyze whisker growth. NaCl was used as a source of Cl for vapor-phase transportation of Ta and Nb oxochlorides and Ti chlorides to the catalyst. The catalyst metal was recycled several times during the synthesis and was transported as NiCl₂( g ) according to thermodynamic calculations. The rate of formation and the chemical composition of the whiskers depended on the synthesis temperature, the choice of catalyst, and the atmosphere. At low temperatures, the whiskers were enriched in Nb and Ta, whereas the Ti content increased with increased synthesis temperature.