色氨酸辅助合成光催化活性增强的球形纳米TiO2

以L-色氨酸（L-Trp）为生物模板,采用简单水解及煅烧后制备了球形结构TiO₂纳米光催化剂。通过X射线衍射、扫描电子显微镜、红外光谱、紫外-可见漫反射光谱、光致发光光谱和N₂吸附-解吸等方法对制得的TiO₂纳米材料进行表征。在催化剂合成过程中,L-Trp作为生物模板发挥至关重要的作用,能够指导球形结构纳米TiO₂的形成。考察了不同煅烧温度下制备的TiO₂样品光催化活性,结果表明550℃时制备的TiO₂样品具有优异的光催化活性,紫外光照射30min对甲基橙溶液的降解率达到95%左右,主要是由于较大比表面积和球形结构的协同效应。光催化剂稳定性实验表明,所制备的TiO₂纳米材料可作为一种实用有效的光催化剂用于紫外光照射下降解有机染料。同时,对L-Trp辅助下球形结构TiO₂纳米颗粒的可能生长机理进行讨论。     

Preparation and photocatalytic properties of a nanometer ZnO–SnO2 coupled oxide

A nanometer coupled oxide ZnO–SnO₂ was prepared using the co-precipitation method employing NH₃·H₂O as the precipitant. The oxide was characterized by X-ray diffraction (XRD), transmission electron microscope (TEM) and UV diffuse reflectance spectrum (DRS). The photocatalytic activity of nanometer coupled oxides was studied using methyl orange as a mode organic pollutant. The relationship between the photocatalytic activity and the microstructure of nanometer coupled oxides was also discussed in the paper. Experimental results showed that the nanometer coupled oxides mainly consist of nanometer ZnO and SnO₂, and they have the same excellent photocatalytic activity as Degussa P25 TiO₂ for the degradation of methyl orange (MO). Moreover, the photocatalytic activity of the coupled oxides increases gently at first, then decreases rapidly with the increase of the calcination temperature. But a small amount of nanometer Zn₂SnO₄ was formed in the mixture of coupled oxides when the calcination temperature was higher than 700 °C.     

The preparation of coupled WO3/TiO2 photocatalyst by ball milling

The coupled photocatalyst WO₃/TiO₂ is prepared by ball milling by doping WO₃ into TiO₂ and using H₂O solution as disperser. The coupled photocatalyst WO₃/TiO₂ is characterized by UV–VIS diffuse reflection spectrum, X-ray photoelectron spectroscopy (XPS), X-ray powder diffraction (XRD) and Transmission electron microscopy (TEM). The results show that the optimum percentage of WO₃ doped is 3% and that the photocatalytic activity of the coupled WO₃/TiO₂ photocatalyst is much higher than that of TiO₂ and WO₃–TiO₂ with no ball milling. Compared with TiO₂, the photoexcited wavelength range of the WO₃/TiO₂ photocatalyst red-shifts about 50 nm, and the light absorption intensity is also improved. The crystal phase of TiO₂ is not changed and new crystal phases are not found during the process of ball milling. WO₃ and TiO₂ coupled highly, forming the WO₃/TiO₂ photocatalyst. The increased photocatalytic activity of the coupled photocatalyst may be attributed to the enhance charge separation efficiency and the extend wavelength range of photoexcitation.     

Visible light photocatalysis on praseodymium(III)-nitrate-modified TiO2 prepared by an ultrasound method

Nanocrystalline TiO₂ incorporated with praseodymium(III) nitrate has been prepared by an ultrasound method in a sol–gel process. The prepared sample is characterized by X-ray diffraction (XRD), nitrogen adsorption (BET surface area), UV–vis diffuse reflectance spectroscopy (UV–Vis DRS) and X-ray photoelectron spectroscopy (XPS). The prepared material consists of TiO₂ nanocrystalline with 5 nm size incorporated with highly dispersed Pr(NO₃)₃. Visible light absorptions at 444, 469, 482 and 590 nm are observed in the prepared sample. These bands are attributed to the 4f transitions ³H₄ → ³P₂, ³H₄ → ³P₁, ³H₄ → ³P₀ and ³H₄ → ¹D₂ of praseodymium(III) ions, respectively. This sample Pr(NO₃)₃-TiO₂, as a novel visible light photocatalyst, shows high activity and stability in the decomposing rhodamine-B (RhB) and 4-chlorophenol (4-CP) under visible light irradiation. Results examined by electron spin resonance spectroscopy (ESR) reveal that the irradiation (>420 nm) of the photocatalyst dispersed in RhB aqueous solution induces the generation of highly active hydroxyl radicals (OH), leading to the cleavage of the whole conjugated chromophore structure of RhB. A mechanism based on local excitation of praseodymium(III) nitrate chromophore and interfacial charge transfer from the chromophore to TiO₂ is proposed to explain the formation of active hydroxyl radicals in the photocatalytic system under visible light irradiation.     

Hydrothermal doping method for preparation of Cr-TiO2 photocatalysts with concentration gradient distribution of Cr

Cr³⁺-doped anatase titanium dioxide photocatalysts were prepared by the combination of sol–gel process with hydrothermal treatment. The samples were characterized by UV–vis diffuse reflectance spectroscopy, X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) specific surface area (S_BET), transmission electron microscopy (TEM), atomic absorption flame emission spectroscopy (AAS), electron paramagnetic resonance (EPR) spectroscopy and X-ray photoelectron spectroscopy (XPS). It was confirmed that Cr substitutes Ti⁴⁺ in TiO₂ lattice in trivalent ionic state, and the concentrations of dopants Cr³⁺ decrease from the exterior to the interior of doped TiO₂. The photocatalytic activity of Cr-TiO₂ was investigated for the photocatalytic degradation of XRG aqueous solution both under UV and visible light irradiation. Due to the excitation of 3d electron of Cr³⁺ to the conduction band of TiO₂, Cr-TiO₂ shows a good ability for absorbing the visible light to degrade XRG. Doping of chromium ions effectively improves the photocatalytic activity under both UV light irradiation and visible light irradiation with an optimal doping concentration of 0.15% and 0.2%, respectively. The special distribution of dopants Cr³⁺ seems having a good effect on enhancing the photocatalytic activity of Cr-TiO₂.     

Structural peculiarities of TiO2 and Pt/TiO2 catalysts for the photocatalytic oxidation of aqueous solution of Acid Orange 7 Dye upon ultraviolet light

TiO₂ (anatase) with different microstructure was synthesized by thermal hydrolysis of the titanyl sulfate and studied by X-ray powder diffraction, high resolution transmission electron microscopy and UV–vis diffuse reflectance spectroscopy. The effect of titanium dioxide structure, regular or distorted, on the photocatalytic degradation of Acid Orange 7 Dye (AO7) in water upon ultraviolet light was studied. It was found that synthesized TiO₂ possesses a relatively high reactivity when illuminated but also show different adsorption in the dark. The relationship between these behaviors depends on the real structure of the catalysts. Catalysts with a perfect structural ordering formed after heating at temperature higher than 500 °C show better photocatalytic performance. Small amount of Pt added into the TiO₂ structure was found to improve further the catalyst reactivity. Pt-modified titania catalysts oxidize AO7 more efficiently than P-25 Degussa TiO₂. Doping effect of Pt on the structural and photocatalytic properties of the samples is discussed.     

Preparation of Au/TiO2 catalysts from Au(I)–thiosulfate complex and study of their photocatalytic activity for the degradation of methyl orange

Gold loaded on TiO₂ (Au/TiO₂) catalysts were prepared using Au(I)–thiosulfate complex (Au(S₂O₃)₂³⁻) as the gold precursor for the first time. The samples were characterized by UV–vis diffuse reflectance spectra, X-ray diffraction (XRD), transmission electron microscopy (TEM), atomic absorption flame emission spectroscopy (AAS), and X-ray photoelectron spectroscopy (XPS) methods. Using Au(S₂O₃)₂³⁻ as gold precursor, ultra-fine gold nanoparticles with a highly disperse state can be successfully formed on the surface of TiO₂. The diameter of Au nanoparticles increases from 1.8 to 3.0 nm with increasing the nominal Au loading from 1% to 8%. The photocatalytic activity of Au/TiO₂ catalysts was evaluated from the analysis of the photodegradation of methyl orange (MO). With the similar Au loading, the catalysts prepared with Au(S₂O₃)₂³⁻ precursor exhibit higher photocatalytic activity for methyl orange degradation when compared with the Au/TiO₂ catalysts prepared with the methods of deposition–precipitation (DP) and impregnation (IMP). The preparation method has decisive influences on the morphology, size and number of Au nanoparticles loaded on the surface of TiO₂ and further affects the photocatalytic activity of the obtained catalysts.     

Low temperature preparation and visible light photocatalytic activity of mesoporous carbon-doped crystalline TiO2

A visible-light-active TiO₂ photocatalyst was prepared through carbon doping by using glucose as carbon source. Different from the previous carbon-doped TiO₂ prepared at high temperature, our preparation was performed by a hydrothermal method at temperature as low as 160 °C. The resulting photocatalyst was characterized by XRD, XPS, TEM, nitrogen adsorption, and UV–vis diffuse reflectance spectroscopy. The characterizations found that the photocatalyst possessed a homogeneous pore diameter about 8 nm and a high surface area of 126 m²/g. Comparing to undoped TiO₂, the carbon-doped TiO₂ showed obvious absorption in the 400–450 nm range with a red shift in the band gap transition. It was found that the resulting carbon-doped TiO₂ exhibits significantly higher photocatalytic activity than the undoped counterpart and Degussa P25 on the degradation of rhodamine B (RhB) in water under visible light irradiation (λ > 420 nm). This method can be easily scaled up for industrial production of visible-light driven photocatalyst for pollutants removal because of its convenience and energy-saving.     

Synthesis, structure and photocatalytic properties of Fe(III)-doped TiO2 prepared from TiCl3

Iron(III)-doped titanium dioxide photocatalysts were prepared from aqueous titanium(III) chloride solution in the presence of dissolved FeCl₃ (0–10.0 at.% relative to TiCl₃) by co-precipitation method. The precipitate was completely oxidized in the aerated suspension, hydrothermally treated, washed and calcinated. The structure of the powders was characterized by thermoanalysis (TG-DTA), diffuse reflectance spectroscopy (DRS), X-ray diffraction (XRD), nitrogen adsorption and transmission electron microscopy (TEM). The light absorption of the iron-containing powders is red shifted relative to the bare sample. The particle size and anatase content were found to significantly decrease at iron contents ≥6.0 at.% which is accompanied with the increase of their specific surface area. XANES measurements showed that the local structure of iron systematically changes with the variation of the dopant concentrations: at higher Fe-contents, hematite- or goethite-like environments were observed, consistent with the formation of separate X-ray amorphous Fe(III)-containing phases. The local structure of iron gradually transformed with decreasing dopant concentrations, possibly due to substitution of Fe(III) in the titania (TiO₂) crystal lattice. Energy dispersive X-ray analysis (EDX) and chemical analysis was used to characterize the iron content of the samples in the bulk and X-ray photoelectron spectroscopy (XPS) in the surface layer of the particles. The photocatalytic performance of the prepared photocatalysts was compared with the activity of Aldrich anatase under UV–vis and VIS irradiation in two different photoreactors. Maximum photocatalytic performance was found at 3.0 at.% iron concentration for UV–vis and at 1.2 at.% for VIS irradiation. Doping with iron(III) ions increased the photodegradation rate of phenol by a factor of three for UV–vis irradiation and by a factor of two for VIS irradiation, relative to the bare photocatalyst.     

Effects of hydrothermal temperature and time on the photocatalytic activity and microstructures of bimodal mesoporous TiO2 powders

Bimodal nanocrystalline mesoporous TiO₂ powders with high photocatalytic activity were prepared by a hydrothermal method using tetrabutylorthotitanate (TiO(C₄H₉)₄, TBOT) as precursor. The as-prepared TiO₂ powders were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS) and N₂ adsorption–desorption measurements. The photocatalytic activity of the as-prepared TiO₂ powders was evaluated by the photocatalytic degradation of acetone (CH₃COCH₃) under UV-light irradiation at room temperature in air. The effects of hydrothermal temperature and time on the microstructures and photocatalytic activity of the TiO₂ powders were investigated and discussed. It was found that hydrothermal treatment enhanced the phase transformation of the TiO₂ powders from amorphous to anatase and crystallization of anatase. All TiO₂ powders after hydrothermal treatment showed bimodal pore-size distributions in the mesoporous region: one was intra-aggregated pores with maximum pore diameters of ca. 4–8 nm and the other with inter-aggregated pores with maximum pore diameters of ca. 45–50 nm. With increasing hydrothermal temperature and time, the average crystallite size and average pore size increased, in contrast, the Brunauer-Emmett-Teller (BET) specific surface areas, pore volumes and porosity steadily decreased. An optimal hydrothermal condition (180 °C for 10 h) was determined. The photocatalytic activity of the prepared TiO₂ powders under optimal hydrothermal conditions was more than three times higher than that of Degussa P25.     

SBA-15/Ni/TiO2/CNTs复合材料的制备及其光催化性能

通过溶胶凝胶法,经多次涂覆在SBA-15上负载掺杂镍的纳米TiO₂,得到SBA-15/NiO/TiO₂复合物;再以TiO₂中还原态金属镍为催化剂,通过化学气相沉积法（CVD）,在SBA-15/NiO/TiO₂表面原位生长碳纳米管,制得SBA-15/Ni/TiO₂/CNTs复合材料。通过XRD、SEM、TEM、UV-Vis和Raman等方法考察了SBA-15/Ni/TiO₂/CNTs复合材料的结构和性能,并通过降解亚甲基蓝溶液评价其光催化活性。结果表明,SBA-15/Ni/TiO₂/CNTs复合光催化剂的催化活性较SBA-15/NiO/TiO₂显著提高。 二次涂覆掺杂镍的二氧化钛制得的复合光催化剂的催化活性高于一次涂覆。     

Photocatalytic degradation of Chromotrope 2R using nanocrystalline TiO2/activated-carbon composite catalysts

Composite catalysts made of nanocrystalline TiO₂ and carbon were prepared by a modified sol–gel method over activated carbon (AC). The composite catalysts were characterized by N₂ adsorption–desorption isotherm, TG, diffuse reflectance UV–vis spectroscopy, XRD and SEM. The photocatalytic activity was tested on the degradation of Chromotrope 2R (C2R) in aqueous medium under UV radiation. The composite catalysts exhibited higher activities than commercial Degussa P25 alone and the photocatalytic process was more efficient than the pure photolytic degradation. A modified Langmuir–Hinshelwood approach was used to study the kinetics and to determine the adsorption equilibrium constant and the reaction rate constant. Two different mechanisms are proposed and discussed in order to explain the observed synergy.     

Influence of operating parameters on photocatalytic degradation of phenol in UV/TiO2 process

The use of hydrogen peroxide (H₂O₂) for improved photocatalytic degradation of phenol in aqueous suspension of commercial TiO₂ powders (Degussa P-25) was investigated. Photodegradation was compared using direct photolysis (UV alone), H₂O₂/UV, TiO₂/UV, and H₂O₂/TiO₂/UV processes in a batch reactor with high-pressure mercury lamp irradiation. The effects of operating parameters such as catalyst dosage, light intensity, pH of the solution, the initial phenol, and H₂O₂ concentrations on photodegradation process were examined. It was shown that photodegradation using H₂O₂/TiO₂/UV process was much more effective than using either H₂O₂/UV or TiO₂/UV process. The effect of the initial phenol concentration on TOC removal was also studied, demonstrating that more than 8 h was required to completely mineralize phenol into water and carbon dioxide. For all the four oxidation processes studied, photodegradation followed the first-order kinetics. The apparent rate constants with 400-W UV ranged from 5.0 × 10⁻⁴ min⁻¹ by direct photolysis to 1.4 × 10⁻² min⁻¹ using H₂O₂/TiO₂/UV process. The role of H₂O₂ on such enhanced photodegradation of phenol in aqueous solution was finally discussed.     

Preparation and gaseous photocatalytic activity of smooth potassium dititanate film

A new smooth potassium dititanate film was prepared by sol-gel method and characterized by thermogravimetry (TG) and differential scanning calorimetry (DSC), X-ray diffraction (XRD), atomic force microscopy (AFM), UV-Visible diffuse reflectance and Raman spectroscopy. The gaseous photocatalytic activity of smooth K₂Ti₂O₅ films was studied using contact angle analysis from the photocatalytic decomposition of octadecyltrichlorosilane (OTS) based self-assembled monolayers (SAMs) formed on K₂Ti₂O₅ films. The photocurrent response of the film was determined by an electrochemical method. It was shown that the films were smooth, compact, and transparent when formed on glass. Compared with TiO₂ film, the K₂Ti₂O₅ film showed wide absorption in the ultraviolet and visible region. It was found that the monolayers on K₂Ti₂O₅ decomposed much faster than those on TiO₂ under UV irradiation of 254 nm in air. The film also exhibited a stronger photoresponse and a more stable anodic photocurrent. The K₂Ti₂O₅ film efficiently decomposes the alkylsiloxane monolayers under UV irradiation in air and it was found to be a good photocatalyst for gaseous organic pollutant treatment.     

Photocatalytic activity of Cu2O/TiO2, Bi2O3/TiO2 and ZnMn2O4/TiO2 heterojunctions

Cu₂O/TiO₂, Bi₂O₃/TiO₂ and ZnMn₂O₄/TiO₂ heterojunctions were studied for potential applications in water decontamination technology and their capacity to induce an oxidation process under VIS light. UV–vis spectroscopy analysis showed that the junctions-based Cu₂O, Bi₂O₃ and ZnMn₂O₄ are able to absorb a large part of visible light (respectively, up to 650, 460 and 1000 nm). This fact was confirmed in the case of Cu₂O/TiO₂ and Bi₂O₃/TiO₂ by photocatalytic experiments performed under visible light. A part of the charge recombination that can take place when both semiconductors are excited was observed when a photocatalytic experiment was performed under UV–vis illumination. Orange II, 4-hydroxybenzoic and benzamide were used as pollutants in the experiment. Photoactivity of the junctions was found to be strongly dependent on the substrate. The different phenomena that were observed in each case are discussed.     

Synthesis of nanosized TiO2/SiO2 particles in the microemulsion and their photocatalytic activity on the decomposition of p-nitrophenol

Nanosized pure TiO₂ particles were prepared by hydrolysis of TTIP in the sodium bis(2-ethylhexyl)sulfosuccinate (AOT) reverse micelles. TiO₂/SiO₂ nanoparticles were also prepared from TEOS as a silicon source and TTIP as a titanium source. These particles were characterized by TEM, XRD, FT-IR, BET, TGA and DTA. From thermal analysis and XRD analysis, the anatase structure of pure titania appeared in the 300–600 °C calcination temperature range and the rutile structure was showed above 700 °C. However, no rutile phase was observed for the TiO₂/SiO₂ particles up to 800 °C. The crystallite size decreased and the surface area of TiO₂/SiO₂ particles monotonically increased with an increase of the silica content. From FT-IR analysis, the band for Ti–O–Si vibration was observed and the band intensity for Si–O–Si vibration increased with an increase of the silica content. The micrographs of TEM showed that the TiO₂/SiO₂ nanoparticles had a spherical and a narrow size distribution. In addition, TiO₂/SiO₂ particles showed higher photocatalytic activity than pure TiO₂ and the TiO₂/SiO₂ (90/10) particles showed the highest activity on the photocatalytic decomposition of p-nitrophenol.     

Synthesis, characterization and photocatalytic activity of N-doped TiO2 modified by platinum chloride

Structures and photocatalytic performance of N-doped TiO₂ modified by platinum chloride (PtCl_x/N-TiO₂) was investigated. It was found that the PtCl_x/N-TiO₂ forms anatase structure of TiO₂ involving nitrogen, chloride species and platinum ions (+IV) as major species, and it exhibits higher photocatalytic activity than either N-TiO₂ or PtCl_x/TiO₂ for the decomposition of acetic acid or acetaldehyde in aqueous solutions under visible light irradiation (λ > 420 nm). An enhancement of the photocatalytic activity on PtCl_x/N-TiO₂ has been proposed as a Z-scheme mechanism for charge separation between platinum chloride and N-TiO₂.     

Preparations and photocatalytic properties of magnetically separable nitrogen-doped TiO2 supported on nickel ferrite

A magnetically separable nitrogen-doped photocatalyst TiO_2−xN_x/SiO₂/NiFe₂O₄ (TSN) with a typical ferromagnetic hysteresis was prepared by a simple process: the magnetic SiO₂/NiFe₂O₄ (SN) dispersion prepared by a liquid catalytic phase transformation method and the visible-light-active photocatalyst TiO_2−xN_x were mixed, sonificated, dried, and calcined at 400 °C. The prepared photocatalyst is photoactive under visible light irradiation and easy to be separated from a slurry-type photoreactor under the application of an external magnetic field, being one of promising photocatalysts for wastewater treatment. Transmission electron microscope (TEM) and X-ray diffractometer (XRD) were used to characterize the structure of the TSN photocatalyst. The results indicate that the magnetic SiO₂/NiFe₂O₄ (SN) nanoparticles adhere to the surface of TiO_2−xN_x congeries. The magnetic photocatalyst TSN shows high catalytic activity for the degradation of methyl orange in water under UV and visible light irradiation (λ > 400 nm). SiO₂ coating round the surface of NiFe₂O₄ nanoparticles prevents effectively the injection of charges from TiO₂ particles to NiFe₂O₄, which gives rise to the increase in photocatalytic activity. Moreover, the recycled TSN exhibits a good repeatability of the photocatalytic activity.     

Physicochemical properties and photocatalytic activities of TiO2-films prepared by sol–gel methods

The physicochemical properties, the photocatalytic activities in aqueous solution and the adhesion properties of supported TiO₂ films prepared by different sol–gel methods have been studied. The thickness, the TiO₂ loading and the photocatalytic activities are influenced by the nature of the stabilising agent. By contrast, the nature of the organic titanium precursor, as well as the solvent and the absence of stabilising agents are determining for the resulting photocatalytic activities. Titania-sol generated by non-controlled hydrolysis of titanium isopropoxide was used to determine the influence (i) of number of coating, (ii) of the calcination temperature and (iii) of the nature of support on the photocatalytic activity under direct and backside irradiation. The higher the coating number, the thicker the TiO₂-film and the higher the photocatalytic efficiency. the optimum calcination temperature was found to be 400 °C. Migration of cationic species into TiO₂-films and the decrease of thickness at higher temperatures lead to the decline of activity.