Degradation of the emerging contaminant ibuprofen in water by photo-Fenton

In this study the degradation of the worldwide Non-Steroidal Anti-Inflammatory Drug (NSAID) ibuprofen (IBP) by photo-Fenton reaction by use of solar artificial irradiation was carried out. Non-photocatalytic experiments (complex formation, photolysis and UV/Vis-H₂O₂ oxidation) were executed to evaluate the isolated effects and additional differentiated degradation pathways of IBP. The solar photolysis cleavage of H₂O₂ generates hydroxylated-IBP byproducts without mineralization. Fenton reaction, however promotes hydroxylation with a 10% contamination in form of a mineralization. In contrast photo-Fenton in addition promotes the decarboxylation of IBP and its total depletion is observed. In absence of H₂O₂ a decrease of IBP was observed in the Fe(II)/UV-Vis process due to the complex formation between iron and the IBP-carboxylic moiety. The degradation pathway can be described as an interconnected and successive principal decarboxylation and hydroxylation steps. TOC depletion of 40% was observed in photo-Fenton degradation. The iron-IBP binding was the key-point of the decarboxylation pathway. Both decarboxylation and hydroxylation mechanisms, as individual or parallel process are responsible for IBP removal in Fenton and photo-Fenton systems. An increase in the biodegradability of the final effluent after photo-Fenton treatment was observed. Final BOD₅ of 25 mg L⁻¹ was reached in contrast to the initial BOD₅ shown by the untreated IBP solution (BOD₅ < 1 mg L⁻¹). The increase in the biodegradability of the photo-Fenton degradation byproducts opens the possibility for a complete remediation with a final post-biological treatment.     

Biodegradability enhancement of a pesticide-containing bio-treated wastewater using a solar photo-Fenton treatment step followed by a biological oxidation process

This work proposes an efficient combined treatment for the decontamination of a pesticide-containing wastewater resulting from phytopharmaceutical plastic containers washing, presenting a moderate organic load (COD = 1662-1960 mg O₂ L⁻¹; DOC = 513-696 mg C L⁻¹), with a high biodegradable organic carbon fraction (81%; BOD₅ = 1350-1600 mg O₂ L⁻¹) and a remaining recalcitrant organic carbon mainly due to pesticides. Nineteen pesticides were quantified by LC-MS/MS at concentrations between 0.02 and 45 mg L⁻¹ (14-19% of DOC). The decontamination strategy involved a sequential three-step treatment: (a) biological oxidation process, leading to almost complete removal of the biodegradable organic carbon fraction; (b) solar photo-Fenton process using CPCs, enhancing the bio-treated wastewater biodegradability, mainly due to pesticides degradation into low-molecular-weight carboxylate anions; (c) and a final polishing step to remove the residual biodegradable organic carbon, using a biological oxidation process. Treatment performance was evaluated in terms of mineralization degree (DOC), pesticides content (LC-MS/MS), inorganic ions and low-molecular-weight carboxylate anions (IC) concentrations. The estimated phototreatment energy necessary to reach a biodegradable wastewater, considering pesticides and low-molecular-weight carboxylate anions concentrations, Zahn-Wellens test and BOD₅/COD ratio, was only 2.3 kJ_UV L⁻¹ (45 min of photo-Fenton at a constant solar UV power of 30 W m⁻²), consuming 16 mM of H₂O₂, which pointed to 52% mineralization and an abatement higher than 86% for 18 pesticides. The biological oxidation/solar photo-Fenton/biological oxidation treatment system achieved pesticide removals below the respective detection limits and 79% mineralization, leading to a COD value lower than 150 mg O₂ L⁻¹, which is in agreement with Portuguese discharge limits regarding water bodies.     

Degradation of a four-pesticide mixture by combined photo-Fenton and biological oxidation

Complete degradation of a pesticide mixture by a combination of a photo-Fenton pretreatment and an activated-sludge batch reactor is demonstrated. Four commercial pesticides, Laition, Metasystox, Sevnol and Ultracid were chosen for this experiment. The active ingredients are, respectively, dimethoate, oxydemeton-methyl, carbaryl and methidathion. The original pesticide concentration was 200 mg L⁻¹. Biotreatment began after 31% photocatalytic mineralization, which after 5 h in a 6-L stirred batch-mode tank reactor with non-acclimated activated sludge, leaves the photo-Fenton effluent completely degraded. This biotreatment time is shorter than commonly found in municipal wastewater treatment plants (∼8-10 h). Therefore, the combined process is effective for rapid pesticide degradation in wastewater with complete removal of parent compounds and the associated DOC concentration. Nonetheless, assessment of this technology should take into account higher pesticide concentrations and how this factor affects both the photocatalytic and the biological oxidation.     

Solar photo-Fenton process on the abatement of antibiotics at a pilot scale: Degradation kinetics, ecotoxicity and phytotoxicity assessment and removal of antibiotic resistant enterococci

This work investigated the application of a solar driven advanced oxidation process (solar photo-Fenton), for the degradation of antibiotics at low concentration level (μg L⁻¹) in secondary treated domestic effluents at a pilot-scale. The examined antibiotics were ofloxacin (OFX) and trimethoprim (TMP). A compound parabolic collector (CPC) pilot plant was used for the photocatalytic experiments. The process was mainly evaluated by a fast and reliable analytical method based on a UPLC-MS/MS system. Solar photo-Fenton process using low iron and hydrogen peroxide doses ([Fe²⁺]₀ = 5 mg L⁻¹; [H₂O₂]₀ = 75 mg L⁻¹) was proved to be an efficient method for the elimination of these compounds with relatively high degradation rates. The photocatalytic degradation of OFX and TMP with the solar photo-Fenton process followed apparent first-order kinetics. A modification of the first-order kinetic expression was proposed and has been successfully used to explain the degradation kinetics of the compounds during the solar photo-Fenton treatment. The results demonstrated the capacity of the applied advanced process to reduce the initial wastewater toxicity against the examined plant species (Sorghum saccharatum, Lepidium sativum, Sinapis alba) and the water flea Daphnia magna. The phytotoxicity of the treated samples, expressed as root growth inhibition, was higher compared to that observed on the inhibition of seed germination. Enterococci, including those resistant to OFX and TMP, were completely eliminated at the end of the treatment. The total cost of the full scale unit for the treatment of 150 m³ day⁻¹ of secondary wastewater effluent was found to be 0.85 € m⁻³.     

Performance of a Sequencing Batch Biofilm Reactor for the treatment of pre-oxidized Sulfamethoxazole solutions

A combined strategy of a photo-Fenton pretreatment followed by a Sequencing Batch Biofilm Reactor (SBBR) was evaluated for total C and N removal from a synthetic wastewater containing exclusively 200 mg L⁻¹ of the antibiotic Sulfamethoxazole (SMX). Photo-Fenton reaction was optimized at the minimum reagent doses in order to improve the biocompatibility of effluents with the subsequent biological reactor. Consequently, the pretreatment was performed with two different initial H₂O₂ concentrations (300 and 400 mg L⁻¹) and 10 mg L⁻¹ of Fe²⁺. The pre-treated effluents with the antibiotic intermediates as sole carbon source were used as feed for the biological reactor. The SBBR was operated under aerobic conditions to mineralize the organic carbon, and the Hydraulic Retention Time (HRT) was optimized down to 8 h reaching a removal of 75.7% of the initial Total Organic Carbon (TOC). The total denitrification of the NO₃⁻ generated along the chemical-biological treatment was achieved by means of the inclusion of a 24-h anoxic stage in the SBBR strategy. In addition, the Activated Sludge Model No. 1 (ASM1) was successfully used to complete the N balance determining the N fate in the SBBR.The characterization and the good performance of the SBBR allow presenting the assessed combination as an efficient way for the treatment of wastewaters contaminated with biorecalcitrant pharmaceuticals as the SMX.     

Decolorization of dark brown colored coffee effluent by solar photo-Fenton reaction: effect of solar light dose on decolorization kinetics

The decolorization of dark brown colored coffee effluent by solar photo-Fenton process has been studied. Effects of accumulated solar light energy and dosage of Fenton reagents (iron and hydrogen peroxide) on the color removal have been examined. With increasing Fe dosage the rate of the decolorization increased but the enhancement was not pronounced beyond 10 mg L⁻¹. Although addition of H₂O₂ increased the decolorization rate up to around 1000 mg L⁻¹ of H₂O₂, further addition of H₂O₂ could not enhance the color removal. At excess dosages of Fenton reagents, the color removal was not improved due to their scavenging of hydroxyl radicals. It was found that the pseudo-first order decolorization kinetic constant based on the accumulated solar energy is a sole parameter unifying solar photo-Fenton decolorization processes under the different weather conditions. The kinetic constant can be readily used to calculate the amount of solar energy required to achieve a certain degree of color removal. The mineralization was rather slower as compared with the decolorization. The decolorization capability with solar irradiation was found to be comparable to UV light irradiation. The present results suggest that abundant solar energy driving decolorization of coffee effluent by photo-Fenton reaction is highly efficient.     

Degradation of fifteen emerging contaminants at μg L initial concentrations by mild solar photo-Fenton in MWTP effluents

The degradation of 15 emerging contaminants (ECs) at low concentrations in simulated and real effluent of municipal wastewater treatment plant with photo-Fenton at unchanged pH and Fe = 5 mg L⁻¹ in a pilot-scale solar CPC reactor was studied. The degradation of those 15 compounds (Acetaminophen, Antipyrine, Atrazine, Caffeine, Carbamazepine, Diclofenac, Flumequine, Hydroxybiphenyl, Ibuprofen, Isoproturon, Ketorolac, Ofloxacin, Progesterone, Sulfamethoxazole and Triclosan), each with an initial concentration of 100 μg L⁻¹, was found to depend on the presence of CO₃²⁻ and HCO₃⁻ (hydroxyl radicals scavengers) and on the type of water (simulated water, simulated effluent wastewater and real effluent wastewater), but is relatively independent of pH, the type of acid used for release of hydroxyl radicals scavengers and the initial H₂O₂ concentration used. Toxicity tests with Vibrio fisheri showed that degradation of the compounds in real effluent wastewater led to toxicity increase.     

Treatment of a sanitary landfill leachate using combined solar photo-Fenton and biological immobilized biomass reactor at a pilot scale

A solar photo-Fenton process combined with a biological nitrification and denitrification system is proposed for the decontamination of a landfill leachate in a pilot plant using photocatalytic (4.16 m² of Compound Parabolic Collectors - CPCs) and biological systems (immobilized biomass reactor). The optimum iron concentration for the photo-Fenton reaction of the leachate is 60 mg Fe²⁺ L⁻¹. The organic carbon degradation follows a first-order reaction kinetics (k = 0.020 L kJ_UV⁻¹, r₀ = 12.5 mg kJ_UV⁻¹) with a H₂O₂ consumption rate of 3.0 mmol H₂O₂ kJ_UV⁻¹. Complete removal of ammonium, nitrates and nitrites of the photo-pre-treated leachate was achieved by biological denitrification and nitrification, after previous neutralization/sedimentation of iron sludge (40 mL of iron sludge per liter of photo-treated leachate after 3 h of sedimentation). The optimum C/N ratio obtained for the denitrification reaction was 2.8 mg CH₃OH per mg N-NO₃⁻, consuming 7.9 g/8.2 mL of commercial methanol per liter of leachate. The maximum nitrification rate obtained was 68 mg N-NH₄⁺ per day, consuming 33 mmol (1.3 g) of NaOH per liter during nitrification and 27.5 mmol of H₂SO₄ per liter during denitrification. The optimal phototreatment energy estimated to reach a biodegradable effluent, considering Zahn-Wellens, respirometry and biological oxidation tests, at pilot plant scale, is 29.2 kJ_UV L⁻¹ (3.3 h of photo-Fenton at a constant solar UV power of 30 W m⁻²), consuming 90 mM of H₂O₂ when used in excess, which means almost 57% mineralization of the leachate, 57% reduction of polyphenols concentration and 86% reduction of aromatic content.     

Degradation of 32 emergent contaminants by UV and neutral photo-fenton in domestic wastewater effluent previously treated by activated sludge

This study focuses on the removal of 32 selected micropollutants (pharmaceuticals, corrosion inhibitors and biocides/pesticides) found in an effluent coming from a municipal wastewater treatment plant (MWTP) based on activated sludge. Dissolved organic matter was present, with an initial total organic carbon of 15.9 mg L⁻¹, and a real global quantity of micropollutants of 29.5 μg L⁻¹. The treatments tested on the micropollutants removal were: UV-light emitting at 254 nm (UV₂₅₄) alone, dark Fenton (Fe^2+,3+/H₂O₂) and photo-Fenton (Fe^2+,3+/H₂O₂/light). Different irradiation sources were used for the photo-Fenton experiences: UV₂₅₄ and simulated sunlight. Iron and H₂O₂ concentrations were also changed in photo-Fenton experiences in order to evaluate its influence on the degradation. All the experiments were developed at natural pH, near neutral. Photo-Fenton treatments employing UV₂₅₄, 50 mg L⁻¹ of H₂O₂, with and without adding iron (5 mg L⁻¹ of Fe²⁺ added or 1.48 mg L⁻¹ of total iron already present) gave the best results. Global percentages of micropollutants removal achieved were 98 and a 97% respectively, after 30 min of treatments. As the H₂O₂ concentration increased (10, 25 and 50 mg L⁻¹), best degradations were observed. UV₂₅₄, Fenton, and photo-Fenton under simulated sunlight gave less promising results with lower percentages of removal.The highlight of this paper is to point out the possibility of the micropollutants degradation in spite the presence of DOM in much higher concentrations.     

Degradation of diclofenac by TiO2 photocatalysis: UV absorbance kinetics and process evaluation through a set of toxicity bioassays

In the present study the degradation kinetics and mineralization of diclofenac (DCF) by the TiO₂ photocatalysis were investigated in terms of UV absorbance and COD measurements for a wide range of initial DCF concentrations (5-80 mg L⁻¹) and photocatalyst loadings (0.2-1.6 g TiO₂ L⁻¹) in a batch reactor system. A set of bioassays (Daphnia magna, Pseudokirchneriella subcapitata and Artemia salina) was performed to evaluate the potential detoxification of DCF. A pseudo-first-order kinetic model was found to fit well most of the experimental data, while at high initial DCF concentrations (40 and 80 mg L⁻¹) and at 1.6 g TiO₂ L⁻¹ photocatalyst loading a second-order kinetic model was found to fit the data better. The toxicity of the treated DCF samples on D. magna and P. subcapitata varied during the oxidation, probably due to the formation of some intermediate products more toxic than DCF. Unicellular freshwater algae was found to be very sensitive to the treated samples as well as the results from D. magna test were consistent to those of algae tests. A. salina was not found to be sensitive under the investigated conditions. Finally, UV absorbance analysis were found to be an useful tool for a fast and easy to perform measurement to get preliminary information on the organic intermediates that are formed during oxidation and also on their disappearance rate.     

Heterogenous photocatalytic degradation kinetics and detoxification of an urban wastewater treatment plant effluent contaminated with pharmaceuticals

Degradation kinetics and mineralization of an urban wastewater treatment plant effluent contaminated with a mixture of pharmaceutical compounds composed of amoxicillin (10 mg L⁻¹), carbamazepine (5 mg L⁻¹) and diclofenac (2.5 mg L⁻¹) by TiO₂ photocatalysis were investigated. The photocatalytic effect was investigated using both spiked distilled water and actual wastewater solutions. The process efficiency was evaluated through UV absorbance and TOC measurements. A set of bioassays (Daphnia magna, Pseudokirchneriella subcapitata and Lepidium sativum) was performed to evaluate the potential toxicity of the oxidation intermediates. A pseudo-first order kinetic model was found to fit well the experimental data. The mineralization rate (TOC) of the wastewater contaminated with the pharmaceuticals was found to be really slow (t_1/2 = 86.6 min) compared to that of the same pharmaceuticals spiked in distilled water (t_1/2 = 46.5 min). The results from the toxicity tests of single pharmaceuticals, their mixture and the wastewater matrix spiked with the pharmaceuticals displayed a general accordance between the responses of the freshwater aquatic species (P. subscapitata > D. magna). In general the photocatalytic treatment did not completely reduce the toxicity under the investigated conditions (maximum catalyst loading and irradiation time 0.8 g TiO₂ L⁻¹ and 120 min respectively).     

Coupling membrane separation and photocatalytic oxidation processes for the degradation of pharmaceutical pollutants

The coupling of membrane separation and photocatalytic oxidation has been studied for the removal of pharmaceutical pollutants. The retention properties of two different membranes (nanofiltration and reverse osmosis) were assessed. Comparable selectivity on the separation of pharmaceuticals were observed for both membranes, obtaining a permeate stream with concentrations of each pharmaceutical below 0.5 mg L⁻¹ and a rejected flux highly concentrated (in the range of 16–25 mg L⁻¹ and 18–32 mg L⁻¹ of each pharmaceutical for NF-90 and BW-30 membranes, respectively), when an initial stream of six pharmaceuticals was feeding to the membrane system (10 mg L⁻¹ of each pharmaceutical). The abatement of concentrated pharmaceuticals of the rejected stream was evaluated by means of heterogeneous photocatalytic oxidation using TiO₂ and Fe₂O₃/SBA-15 in presence of hydrogen peroxide as photo-Fenton system. Both photocatalytic treatments showed remarkable removals of pharmaceutical compounds, achieving values between 80 and 100%. The nicotine was the most refractory pollutant of all the studied pharmaceuticals. Photo-Fenton treatment seems to be more effective than TiO₂ photocatalysis, as high mineralization degree and increased nicotine removal were attested. This work can be considered an interesting approach of coupling membrane separation and heterogeneous photocatalytic technologies for the successful abatement of pharmaceutical compounds in effluents of wastewater treatment plants.     

Performance of a passive treatment system for net-acidic coal mine drainage over five years of operation

A full-scale passive treatment system (PTS) was commissioned in 2003 to treat two net-acidic coal mine water discharges in the Durham coalfield, UK. The principal aim of the PTS was to decrease concentrations of iron (< 177 mg L⁻¹) and aluminium (< 85 mg L⁻¹) and to increase pH (> 3.2) and alkalinity (≥ 0 mg L⁻¹ CaCO₃ eq). Secondary objectives were to decrease zinc (< 2.8 mg L⁻¹), manganese (< 20.5 mg L⁻¹) and sulfate (< 2120 mg L⁻¹). Upon treatment, water qualities were improved by 84% in the case of Fe, 87% Al, 83% acidity, 51% Zn, 23% Mn and 29% SO₄²⁻. Alkalinity (74%) and pH (95% as H⁺) were increased. Area adjusted removal rates (Fe = 1.49 ± 0.66 g d⁻¹ m⁻²; acidity = 6.7 ± 4.9 g d⁻¹ m⁻²) were low compared to design criteria, mainly due to load limitation. Disregarding seasonality effects, acidity removal and effluent pH were stable over time. A substantial temporal decrease in calcium and alkalinity generation suggests that limestone is increasingly armoured. Once pH is no longer buffered by the carbonate system, metals could be remobilized, putting treatment efficiency at risk.     

Field solar degradation of pesticides and emerging water contaminants mediated by polymer films containing titanium and iron oxide with synergistic heterogeneous photocatalytic activity at neutral pH

Photocatalytic degradation of phenol, nalidixic acid, mixture of pesticides, and another of emerging contaminants in water was mediated by TiO₂ and iron oxide immobilized on functionalized polyvinyl fluoride films (PVF^f-TiO₂-Fe oxide) in a compound parabolic collector (CPC) solar photoreactor. During degradation, little iron leaching (<0.2 mg L⁻¹) was observed. Phenol was efficiently degraded and mineralized at operational pH < 5 and nalidixic acid degradation was complete even at pH 7, but mineralization stopped at 35%. Pesticide mixture was slowly degraded (50%) after 150 min of irradiation. Degradation of the emergent contaminant mixture was successful for eight compounds and less efficient for six other compounds. The significant reactivity differences between tested compounds were assigned to the differences in structure namely that the presence of complexing or chelating groups enhanced the rates.PVF^f-TiO₂-Fe oxide photoactivity gradually increased during 20 days of experiments. X-ray photoelectron spectroscopy (XPS) measurements revealed significant changes on the catalyst surface. These analyses confirm that during photocatalysis mediated by PVF^f-TiO₂-Fe oxide, some iron leaching led to enlargement of the TiO₂ surface exposed to light, increasing its synergy with iron oxides and leading to enhanced pollutant degradation.     

Effect of bromide on the formation of disinfection by-products during wastewater chlorination

The effect of bromide ion on the formation and speciation of trihalomethanes (THMs) and haloacetic acids (HAAs) during the chlorination of biologically treated wastewaters was investigated. The experimental results showed that the formation of total THMs and total HAAs during chlorine disinfection increased with increasing bromide levels in wastewater. The formation of CHBr₃ increased nearly linearly with increasing bromide ion levels, while CHCl₂Br and CHClBr₂ increased with increasing bromide concentration from 0 to 3.2 mg L⁻¹ and thereafter remained constant or slightly decreased. Increasing initial bromide levels up to 12.8 mg L⁻¹ resulted in sharp decrease of the concentration of CHCl₃ and chloro- HAAs. The mixed bromochloro- HAAs and bromo-only species replaced chloro- HAAs as the dominated species of HAA with increasing bromide levels. The distribution of monohalogenated, dihalogenated and trihalogenated species of HAAs in chlorinated wastewater at high concentration of bromide (>2 mg L⁻¹) is different from that of drinking/natural water. The values of the bromine incorporation factors, n (Br) and n′ (Br), increased with increasing bromide concentration and remained constant or slightly decreased with increasing contact time under the studied range of bromide ion concentrations during chlorination. Moreover, the bromine incorporation into THMs was higher than that of HAAs with bromide levels ranging from 1.0 to 12.8 mg L⁻¹, indicating the dissimilar formation mechanisms of THMs and HAAs involving bromide.     

Degradation of the antibiotic oxolinic acid by photocatalysis with TiO2 in suspension

In the work presented here, a photocatalytic system using titanium Degussa P-25 in suspension was used to evaluate the degradation of 20 mg L⁻¹ of antibiotic oxolinic acid (OA). The effects of catalyst load (0.2-1.5 g L⁻¹) and pH (7.5-11) were evaluated and optimized using the surface response methodology and the Pareto diagram. In the range of variables studied, low pH values and 1.0 g L⁻¹ of TiO₂ favoured the efficiency of the process. Under optimal conditions the evolution of the substrate, chemical oxygen demand, dissolved organic carbon, toxicity and antimicrobial activity on Escherichia coli cultures were evaluated. The results indicate that, under optimal conditions, after 30 min, the TiO₂ photocatalytic system is able to eliminate both the substrate and the antimicrobial activity, and to reduce the toxicity of the solution by 60%. However, at the same time, ∼53% of both initial DOC and COD remain in solution. Thus, the photocatalytical system is able to transform the target compound into more oxidized by-products without antimicrobial activity and with a low toxicity. The study of OA by-products using liquid chromatography coupled with mass spectrometry, as well as the evaluation of OA degradation in acetonitrile media as solvent or in the presence of isopropanol and iodide suggest that the reaction is initiated by the photo-Kolbe reaction. Adsorption isotherm experiments in the dark indicated that under pH 7.5, adsorption corresponded to the Langmuir adsorption model, indicating the dependence of the reaction on an initial adsorption step.     

Characterization of the degradation performance of the sulfamethazine antibiotic by photo-Fenton process

The present study provides results describing the degradation performance of the Sulfamethazine (SMT) antibiotic via photo-Fenton treatment. Experiments were carried out using 1 L solution samples of SMT (50 mg L⁻¹) under different conditions. HPLC results reveal that both Fenton and photo-Fenton reactions were able to completely remove SMT antibiotic from the studied samples in less than 2 min treatment. Half-life times and kinetic parameters (assuming a pseudo-first-order kinetics at reaction initial stage, far from the equilibrium) for SMT degradation were determined and discussed. Hence, appropriate Fenton reagent loads are given to attain different targets proposed. TOC and HPLC data also revealed the presence of reaction intermediates; thus toxicity assays were performed regarding bacterial growth rate. The toxicity of an SMT solution was shown to increase during its degradation by means of photo-Fenton reactions.     

Characterization of copper bioreduction and biosorption by a highly copper resistant bacterium isolated from copper-contaminated vineyard soil

Copper is an essential but toxic heavy metal that negatively impacts living systems at high concentration. This study presents factors affecting copper bioremoval (bioreduction and biosorption) by a highly copper resistant monoculture of Pseudomonas sp. NA and copper bioremoval from soil. Seven bacteria resistant to high concentration of Cu(II) were isolated from enrichment cultures of vineyard soils and mining wastes. Culture parameters influencing copper bioreduction and biosorption by one monoculture isolate were studied. The isolate was identified by 16S rRNA gene sequence analysis as a Pseudomonas sp. NA (98% similarity to Pseudomonas putida, Pseudomonas plecoglossicida and other Pseudomonas sp.). The optimal temperature for growth was 30 °C and bioremoval of Cu(II) was maximal at 35 °C. Considerable growth of the isolate was observed between pH 5.0 and 8.0 with the highest growth and biosorption recorded at pH 6.0. Maximal bioreduction was observed at pH 5.0. Cu(II) bioremoval was directly proportional to Cu(II) concentration in media. Pseudomonas sp. NA removed more than 110 mg L^− 1 Cu(II) in water within 24 h through bioreduction and biosorption at initial concentration of 300 mg L^− 1. In cultures amended with 100 mg L^− 1, 20.7 mg L^− 1 of Cu(II) was biologically reduced and more than 23 mg L^− 1 of Cu(II) was biologically removed in 12 h. The isolate strongly promoted copper bioleaching in soil. Results indicate that Pseudomonas sp. NA has good potential as an agent for removing copper from water and soil.     

Solar treatment of cork boiling and bleaching wastewaters in a pilot plant

This paper reports on cork boiling and bleaching wastewaters treatment by solar photocatalytic processes, TiO₂/UV and Fe²⁺/H₂O₂/UV (TiO₂-only for bleaching wastewater), in a pilot plant with compound parabolic collectors. The photo-Fenton reaction (k = 0.12 L/kJ_UV, r₀ = 59.4 mg/kJ_UV) is much more efficient that TiO₂ photocatalysis and TiO₂ + S₂O₈²⁻ (k = 0.0024 L/kJ_UV, r₀ = 1.36 mg/kJ_UV), leading to 94% mineralization of the bleaching wastewater after 31.5 kJ_UV/L, consuming 77.1 mM of H₂O₂ (3.0 mmol/kJ_UV) and using 20 mg/L of iron. For the cork boiling wastewater, after a slow initial reaction rate, the DOC degradation curve shows a first-order kinetics behaviour (k = 0.015 L/kJ_UV, r₀ = 20.8 mg/kJ_UV) until 173 kJ_UV/L (≈300 mg C/L). According to the average oxidation state (AOS), toxicity profiles, respirometry and kinetic results obtained in two solar CPCs plants, the optimal energy dose estimated for phototreatment to reach a biodegradable effluent is 15 kJ_UV/L and 114 kJ_UV/L, consuming 33 mM and 151 mM of H₂OT:/PGN/ELSEVIER/WR/web/00007490/₂, achieving almost 49% and 48% mineralization of the wastewaters, respectively for the cork bleaching and boiling wastewaters.     

Ultrasonic treatment of water contaminated with ibuprofen

The application of ultrasound (US) waves for remediation of wastewater is an area of increasing interest and promising results. The aim of this paper is to evaluate the influence of several parameters of the US process on the degradation of ibuprofen (IBP), a widely used non-steroidal anti-inflammatory recalcitrant drug found in water. Applied US power, dissolved gas, pH and initial concentration of IBP were the parameters investigated under sonication (300 kHz).Ultrasound increased the degradation of IBP from 30 to 98% in 30 min. Initial rate of IBP degradation was evaluated in the range of 1.35 and 6.1 μmol L⁻¹ min⁻¹ for initial concentrations of 2 to 21 mg L⁻¹ or 9.7 μmol L⁻¹ to 101 μmol L⁻¹, respectively. Under air and oxygen the degradation rate of IBP was 4 μmol L⁻¹ min⁻¹ being higher than that when argon was used. The most favorable degradation pH was acidic media. Complete removal of IBP was achieved but some dissolved organic carbon (DOC) remained in solution showing that long-lived intermediates were recalcitrant to the US irradiation. However, chemical and biological oxygen demands (COD and BOD₅) indicated that the process oxidize the ibuprofen compound to biodegradable substances removable in a subsequent biological step.