Modelling and measurements of power losses and turbulence intensity in wind turbine wakes at Middelgrunden offshore wind farm

Understanding of power losses and turbulence increase due to wind turbine wake interactions in large offshore wind farms is crucial to optimizing wind farm design. Power losses and turbulence increase due to wakes are quantified based on observations from Middelgrunden and state‐of‐the‐art models. Observed power losses due solely to wakes are approximately 10% on average. These are relatively high for a single line of wind turbines due in part to the close spacing of the wind farm. The wind farm model Wind Analysis and Application Program (WAsP) is shown to capture wake losses despite operating beyond its specifications for turbine spacing. The paper describes two methods of estimating turbulence intensity: one based on the mean and standard deviation (SD) of wind speed from the nacelle anemometer, the other from mean power output and its SD. Observations from the nacelle anemometer indicate turbulence intensity which is around 9% higher in absolute terms than those derived from the power measurements. For comparison, turbulence intensity is also derived from wind speed and SD from a meteorological mast at the same site prior to wind farm construction. Despite differences in the measurement height and period, overall agreement is better between the turbulence intensity derived from power measurements and the meteorological mast than with those derived from data from the nacelle anemometers. The turbulence in wind farm model indicates turbulence increase of the order 20% in absolute terms for flow directly along the row which is in good agreement with the observations. Copyright © 2007 John Wiley & Sons, Ltd.     

A stochastic wind turbine wake model based on new metrics for wake characterization

Understanding the detailed dynamics of wind turbine wakes is critical to predicting the performance and maximizing the efficiency of wind farms. This knowledge requires atmospheric data at a high spatial and temporal resolution, which are not easily obtained from direct measurements. Therefore, research is often based on numerical models, which vary in fidelity and computational cost. The simplest models produce axisymmetric wakes and are only valid beyond the near wake. Higher‐fidelity results can be obtained by solving the filtered Navier–Stokes equations at a resolution that is sufficient to resolve the relevant turbulence scales. This work addresses the gap between these two extremes by proposing a stochastic model that produces an unsteady asymmetric wake. The model is developed based on a large‐eddy simulation (LES) of an offshore wind farm. Because there are several ways of characterizing wakes, the first part of this work explores different approaches to defining global wake characteristics. From these, a model is developed that captures essential features of a LES‐generated wake at a small fraction of the cost. The synthetic wake successfully reproduces the mean characteristics of the original LES wake, including its area and stretching patterns, and statistics of the mean azimuthal radius. The mean and standard deviation of the wake width and height are also reproduced. This preliminary study focuses on reproducing the wake shape, while future work will incorporate velocity deficit and meandering, as well as different stability scenarios. Copyright © 2016 John Wiley & Sons, Ltd.     

Quantification of wind turbine energy loss due to leading-edge erosion through infrared-camera imaging,numerical simulations,and assessment against SCADA and meteorological data

Quantification of the performance degradation on the annual energy production (AEP) of a wind farm due to leading-edge (LE) erosion of wind turbine blades is important to design cost-effective maintenance plans and timely blade retrofit. In this work, the effects of LE erosion on horizontal axis wind turbines are quantified using infrared (IR) thermographic imaging of turbine blades, as well as meteorological and SCADA data. The average AEP loss of turbines with LE erosion is estimated from SCADA and meteorological data to be between 3% and 8% of the expected power capture. The impact of LE erosion on the average power capture of the turbines is found to be higher at lower hub-height wind speeds (peak around 50% of the turbine rated wind speed) and at lower turbulence intensity of the incoming wind associated with stable atmospheric conditions. The effect of LE erosion is investigated with IR thermography to identify the laminar to turbulent transition (LTT) position over the airfoils of the turbine blades. Reduction in the laminar flow region of about 85% and 87% on average in the suction and pressure sides, respectively, is observed for the airfoils of the investigated turbines with LE erosion. Using the observed LTT locations over the airfoils and the geometry of the blade, an average AEP loss of about 3.7% is calculated with blade element momentum simulations, which is found to be comparable with the magnitude of AEP loss estimated through the SCADA data.     

Online wind turbine fault detection through automated SCADA data analysis

This paper describes a set of anomaly‐detection techniques and their applicability to wind turbine fault identification. It explains how the anomaly‐detection techniques have been adapted to analyse supervisory control and data acquisition data acquired from a wind farm, automating and simplifying the operators' analysis task by interpreting the volume of data available. The techniques are brought together into one system to collate their output and provide a single decision support environment for an operator. The framework used is a novel multi‐agent system architecture that offers the opportunity to corroborate the output of the various interpretation techniques in order to improve the accuracy of fault detection. The results presented demonstrate that the interpretation techniques can provide performance assessment and early fault identification, thereby giving the operators sufficient time to make more informed decisions regarding the maintenance of their machines. Copyright © 2009 John Wiley & Sons, Ltd.     

Global sensitivity analysis of wind turbine power output

The dynamics of wind turbine behavior are complex and a critical area of study for the wind industry. Identification of factors that cause changes in turbine performance can sometimes prove to be challenging, whereas other times, it can be intuitive. The quantification of the effect that these factors have is valuable for making improvements to both power performance and turbine health. In commercial farms, large quantities of meteorological and performance data are commonly collected to monitor daily operations. These data can also be used to analyze the relationship between each parameter in order to better understand the interactions that occur and the information contained within these signals. In this global sensitivity analysis, a neural network is used to model select wind turbine supervisory control and data acquisition system parameters for an array of turbines from a commercial wind farm that exhibit signs of wake interaction. An extended Fourier amplitude sensitivity test is then performed for 2 years of 10‐min averaged data. The study examines the primary and combined sensitivities of power output to each selected parameter for two turbines in the array. The primary sensitivities correspond to single parameter interactions, whereas combined sensitivities account for interactions between multiple parameters simultaneously. Highly influential parameters such as wind speed and rotor rotation frequency produce expected results; the extended Fourier amplitude sensitivity test method proved effective at quantifying the sensitivity of a wide range of more subtle inputs. These include blade pitch, yaw position, main bearing and ambient temperatures as well as wind speed and yaw position standard deviation. The technique holds promise for application in full‐scale wake studies where it might be used to determine the benefits of emerging power optimization strategies such as active wake management. The field of structural health monitoring can also benefit from this method. Copyright © 2013 John Wiley & Sons, Ltd.     

Simulation of wind turbine wake interaction using the vorticity transport model

The aerodynamic interactions that can occur within a wind farm can result in the constituent turbines generating a lower power output than would be possible if each of the turbines were operated in isolation. Tightening of the constraints on the siting of wind farms is likely to increase the scale of the problem in the future. The aerodynamic performance of turbine rotors and the mechanisms that couple the fluid dynamics of multiple rotors can be most readily understood by simplifying the problem and considering the interaction between only two rotors. The aerodynamic interaction between two rotors in both co‐axial and offset configurations has been simulated using the Vorticity Transport Model. The aerodynamic interaction is a function of the tip speed ratio, and both the streamwise and crosswind separation between the rotors. The simulations show that the momentum deficit at a turbine operating within the wake developed by the rotor of a second turbine is governed by the development of instabilities within the wake of the upwind rotor, and the ensuing structure of the wake as it impinges on the downwind rotor. If the wind farm configuration or wind conditions are such that a turbine rotor is subject to partial impingement by the wake produced by an upstream turbine, then significant unsteadiness in the aerodynamic loading on the rotor blades of the downwind turbine can result, and this unsteadiness can have considerable implications for the fatigue life of the blade structure and rotor hub. Copyright © 2009 John Wiley & Sons, Ltd.     

Contributions to wind farm power estimation considering wind direction‐dependent wake effects

This paper presents a contribution to wind farm ouput power estimation. The calculation for a single wind turbine involves the use of the power coefficient or, more directly, the power curve data sheet. Thus, if the wind speed value is given, a simple calculation or search in the data sheet will provide the generated power as a result. However, a wind farm generally comprises more than one wind turbine, which means the estimation of power generated by the wind farm as a function of the wind speed is a more complex process that depends on several factors, including the important issue of wind direction. While the concept of a wind turbine power curve for a single wind turbine is clear, it is more subject to discussion when applied to a whole wind farm. This paper provides a simplified method for the estimation of wind farm power, based on the use of an equivalent wake effect coefficient. Copyright © 2016 John Wiley & Sons, Ltd.     

A numerical study of tilt‐based wake steering using a hybrid free‐wake method

This study investigates the potential of using tilt‐based wake steering to alleviate wake shielding problems experienced by downwind turbines. Numerical simulations of turbine wakes have been conducted using a hybrid free‐wake analysis combining vortex lattice method (VLM) and an innovative free‐wake model called constant circulation contour method (CCCM). Simulation results indicate tilting a horizontal axis wind turbine's shaft upward causes its wake to ascend, carrying energy‐depleted air upward and pumping more energetic replacement air into downstream turbines, thereby having the potential to recover downstream turbine power generation. Wake cross section vorticity and velocity distributions reveal that the wake upward transport is caused by the formation of near‐wake streamwise vorticity components, and furthermore, the wake velocity deficit is weakened because of the skewed wake structure. Beyond the single turbine wake simulation, an inline two‐turbine case is performed as an assessment of the wake steering influence on the two‐turbine system and as an exploratory work of simulating turbine‐wake interactions using the hybrid free‐wake model. Individual and total turbine powers are calculated. A comparison between different tilting angles suggests turbine power enhancement may be achieved by tilting the upstream turbine and steering its wakes away from the downstream turbine.     

Application of a LES technique to characterize the wake deflection of a wind turbine in yaw

When a wind turbine works in yaw, the wake intensity and the power production of the turbine become slightly smaller and a deflection of the wake is induced. Therefore, a good understanding of this effect would allow an active control of the yaw angle of upstream turbines to steer the wake away from downstream machines, reducing its effect on them. In wind farms where interaction between turbines is significant, it is of interest to maximize the power output from the wind farm as a whole and to reduce fatigue loads on downstream turbines due to the increase of turbulence intensity in wakes. A large eddy simulation model with particular wind boundary conditions has been used recently to simulate and characterize the turbulence generated by the presence of a wind turbine and its evolution downstream the machine. The simplified turbine is placed within an environment in which relevant flow properties like wind speed profile, turbulence intensity and the anisotropy of turbulence are found to be similar to the ones of the neutral atmosphere. In this work, the model is used to characterize the wake deflection for a range of yaw angles and thrust coefficients of the turbine. The results are compared with experimental data obtained by other authors with a particle image velocimetry technique from wind tunnel experiments. Also, a comparison with simple analytical correlations is carried out. Copyright © 2009 John Wiley & Sons, Ltd.     

One‐way mesoscale‐microscale coupling for simulating a wind farm in North Texas: Assessment against SCADA and LiDAR data

One‐way nested mesoscale to microscale simulations of an onshore wind farm have been performed nesting the Weather Research and Forecasting (WRF) model and our in‐house high‐resolution large‐eddy simulation code (UTD‐WF). Each simulation contains five nested WRF domains, with the largest domain spanning the north Texas Panhandle region with a 4 km resolution, while the highest resolution (50 m) nest simulates microscale wind fluctuations and turbine wakes within a single wind farm. The finest WRF domain in turn drives the UTD‐WF LES higher‐resolution domain for a subset of six turbines at a resolution of ～5 m. The wind speed, direction, and boundary layer profiles from WRF are compared against measurements obtained with a met‐tower and a scanning Doppler wind LiDAR located within the wind farm. Additionally, power production obtained from WRF and UTD‐WF are assessed against supervisory control and data acquisition (SCADA) system data. Numerical results agree well with the experimental measurements of the wind speed, direction, and power production of the turbines. UTD‐WF high‐resolution domain improves significantly the agreement of the turbulence intensity at the turbines location compared with that of WRF. Velocity spectra have been computed to assess how the nesting allows resolving a wide range of scales at a reasonable computational cost. A domain sensitivity analysis has been performed. Velocity spectra indicate that placing the inlet too close to the first row of turbines results in an unrealistic peak of energy at the rotational frequency of the turbines. Spectra of the power production of a single turbine and of the cumulative power of the array have been compared with analytical models.     

Application and validation of incrementally complex models for wind turbine aerodynamics,isolated wind turbine in uniform inflow conditions

A comparison of several incrementally complex methods for predicting wind turbine performance, aeroelastic behavior, and wakes is provided. Depending on a wind farm's design, wake interference can cause large power losses and increased turbulence levels within the farm. The goal is to employ modeling methods to reach an improved understanding of wake effects and to use this information to better optimize the layout of new wind farms. A critical decision faced by modelers is the fidelity of the model that is selected to perform simulations. The choice of model fidelity can affect the accuracy, but will also greatly impact the computational time and resource requirements for simulations. To help address this critical question, three modeling methods of varying fidelity have been developed side by side and are compared in this article. The models from low to high complexity are as follows: a blade element‐based method with a free‐vortex wake, an actuator disc‐based method, and a full rotor‐based method. Fluid/structure interfaces are developed for the aerodynamic modeling approaches that allow modeling of discrete blades and are then coupled with a multibody structural dynamics solver in order to perform an aeroelastic analysis. Similar methods have individually been tested by researchers, but we suggest that by developing a suite of models, they can be cross‐compared to grasp the subtleties of each method. The modeling methods are applied to the National Renewable Energy Laboratory Phase VI rotor to predict the turbine aerodynamic and structural loads and then also the wind velocities in the wake. The full rotor method provides the most accurate predictions at the turbine and the use of adaptive mesh refinement to capture the wake to 20 radii downstream is proven particularly successful. Though the full rotor method is unmatched by the lower fidelity methods in stalled conditions and detailed prediction of the downstream wake, there are other less complex conditions where these methods perform as accurately as the full rotor method. Copyright © 2014 John Wiley & Sons, Ltd.     

Wind tunnel investigation on the effect of the turbine tower on wind turbines wake symmetry

In wind farms, the wake of the upstream turbines becomes the inflow for the downstream machines. Ideally, the turbine wake is a stable vortex system. In reality, because of factors like background turbulence, mean flow shear, and tower‐wake interaction, the wake velocity deficit is not symmetric and is displaced away from its mean position. The irregular velocity profile leads to a decreased efficiency and increased blade stress levels for the downstream turbines. The object of this work is the experimental investigation of the effect of the wind turbine tower on the symmetry and displacement of the wake velocity deficit induced by one and two in‐line model wind turbines (,D= 0.9 m). The results of the experiments, performed in the closed‐loop wind tunnel of the Norwegian University of Science and Technology in Trondheim (Norway), showed that the wake of the single turbine expanded more in the horizontal direction (side‐wall normal) than in the vertical (floor normal) direction and that the center of the wake vortex had a tendency to move toward the wind tunnel floor as it was advected downstream from the rotor. The wake of the turbine tandem showed a similar behavior, with a larger degree of non‐symmetry. The analysis of the cross‐stream velocity profiles revealed that the non‐symmetries were caused by a different cross‐stream momentum transport in the top‐tip and bottom‐tip region, induced by the turbine tower wake. In fact, when a second additional turbine tower, mirroring the original one, was installed above the turbine nacelle, the wake recovered its symmetric structure. Copyright © 2017 John Wiley & Sons, Ltd.     

Simulation and wake analysis of a single vertical axis wind turbine

Because of several design advantages and operational characteristics, particularly in offshore farms, vertical axis wind turbines (VAWTs) are being reconsidered as a complementary technology to horizontal axial turbines. However, considerable gaps remain in our understanding of VAWT performance since cross‐flow rotor configurations have been significantly less studied than axial turbines. This study examines the wakes of VAWTs and how their evolution is influenced by turbine design parameters. An actuator line model is implemented in an atmospheric boundary layer large eddy simulation code, with offline coupling to a high‐resolution blade‐scale unsteady Reynolds‐averaged Navier–Stokes model. The large eddy simulation captures the turbine‐to‐farm scale dynamics, while the unsteady Reynolds‐averaged Navier–Stokes captures the blade‐to‐turbine scale flow. The simulation results are found to be in good agreement with three existing experimental datasets. Subsequently, a parametric study of the flow over an isolated VAWT, carried out by varying solidities, height‐to‐diameter aspect ratios and tip speed ratios, is conducted. The analyses of the wake area and velocity and power deficits yield an improved understanding of the downstream evolution of VAWT wakes, which in turn enables a more informed selection of turbine designs for wind farms. Copyright © 2016 John Wiley & Sons, Ltd.     

Adjustment of wind farm power output through flexible turbine operation using wind farm control

When the installed capacity of wind power becomes high, the power generated by wind farms can no longer simply be that dictated by the wind speed. With sufficiently high penetration, it will be necessary for wind farms to provide assistance with supply‐demand matching. The work presented here introduces a wind farm controller that regulates the power generated by the wind farm to match the grid requirements by causing the power generated by each turbine to be adjusted. Further, benefits include fast response to reach the wind farm power demanded, flexibility, little fluctuation in the wind farm power output and provision of synthetic inertia. Copyright © 2015 John Wiley & Sons, Ltd.     

Validation of the dynamic wake meander model for loads and power production in the Egmond aan Zee wind farm

This paper investigates wake effects on load and power production by using the dynamic wake meander (DWM) model implemented in the aeroelastic code HAWC2. The instationary wind farm flow characteristics are modeled by treating the wind turbine wakes as passive tracers transported downstream using a meandering process driven by the low frequent cross‐wind turbulence components. The model complex is validated by comparing simulated and measured loads for the Dutch Egmond aan Zee wind farm consisting of 36 Vestas V90 turbine located outside the coast of the Netherlands. Loads and production are compared for two distinct wind directions—a free wind situation from the dominating southwest and a full wake situation from northwest, where the observed turbine is operating in wake from five turbines in a row with 7D spacing. The measurements have a very high quality, allowing for detailed comparison of both fatigue and min–mean–max loads for blade root flap, tower yaw and tower bottom bending moments, respectively. Since the observed turbine is located deep inside a row of turbines, a new method on how to handle multiple wakes interaction is proposed. The agreement between measurements and simulations is excellent regarding power production in both free and wake sector, and a very good agreement is seen for the load comparisons too. This enables the conclusion that wake meandering, caused by large scale ambient turbulence, is indeed an important contribution to wake loading in wind farms. Copyright © 2012 John Wiley & Sons, Ltd.     

Characterizing power performance and wake of a wind turbine under yaw and blade pitch

Wind turbine wakes have been recognized as a key issue causing underperformance in existing wind farms. In order to improve the performance and reduce the cost of energy from wind farms, one approach is to develop innovative methods to improve the net capacity factor by reducing wake losses. The output power and characteristics of the wake of a utility‐scale wind turbine under yawed flow is studied to explore the possibility of improving the overall performance of wind farms. Preliminary observations show that the power performance of a turbine does not degrade significantly under yaw conditions up to approximately 10°. Additionally, a yawed wind turbine may be able to deflect its wake in the near‐wake region, changing the wake trajectory downwind, with the progression of the far wake being dependent on several atmospheric factors such as wind streaks. Changes in the blade pitch angle also affect the characteristics of the turbine wake and are also examined in this paper. Copyright © 2015 John Wiley & Sons, Ltd.     

Mesoscale modeling of offshore wind turbine wakes at the wind farm resolving scale: a composite‐based analysis with the Weather Research and Forecasting model over Horns Rev

The use of mesoscale modeling to reproduce the power deficits associated with wind turbine wakes in an offshore environment is analyzed. The study is based on multiyear (3 years) observational and modeling results at the Horns Rev wind farm. The simulations are performed with the Weather Research and Forecasting mesoscale model configured at a high horizontal resolution of 333 m over Horns Rev. The wind turbines are represented as an elevated momentum sink and a source of turbulent kinetic energy. Composites with different atmospheric conditions are extracted from both the observed and simulated datasets in order to inspect the ability of the model to reproduce the power deficit in a wide range of atmospheric conditions. Results indicate that mesoscale models such as Weather Research and Forecasting are able to qualitatively reproduce the power deficit at the wind farm scale. Some specific differences are identified. Mesoscale modeling is therefore a suitable framework to analyze potential downstream effects associated with offshore wind farms. Copyright © 2014 John Wiley & Sons, Ltd.     

Predictions of ice formations on wind turbine blades and power production losses due to icing

Prediction of ice shapes on a wind turbine blade makes it possible to estimate the power production losses due to icing. Ice accretion on wind turbine blades is responsible for a significant increase in aerodynamic drag and decrease in aerodynamic lift and may even cause premature flow separation. All these events create power losses and the amount of power loss depends on the severity of icing and the turbine blade profile. The role of critical parameters such as wind speed, temperature, liquid water content on the ice shape, and size is analyzed using an ice accretion prediction methodology coupled with a blade element momentum tool. The predicted ice shapes on various airfoil profiles are validated against the available experimental and numerical data in the literature. The error in predicted rime and glime ice volumes and the maximum ice thicknesses varies between 3% and 25% in comparison with the experimental data depending on the ice type. The current study presents an efficient and accurate numerical methodology to perform an investigation for ice‐induced power losses under various icing conditions on horizontal axis wind turbines. The novelty of the present work resides in a unified and coupled approach that deals with the ice accretion prediction and performance analysis of iced wind turbines. Sectional ice profiles are first predicted along the blade span, where the concurrence of both rime and glaze ice formations may be observed. The power loss is then evaluated under the varying ice profiles along the blade. It is shown that the tool developed may effectively be used in the prediction of power production losses of wind turbines at representative atmospheric icing conditions.     

A generalized framework for reduced‐order modeling of a wind turbine wake

A reduced‐order model for a wind turbine wake is sought from large eddy simulation data. Fluctuating velocity fields are combined in the correlation tensor to form the kernel of the proper orthogonal decomposition (POD). Proper orthogonal decomposition modes resulting from the decomposition represent the spatially coherent turbulence structures in the wind turbine wake; eigenvalues delineate the relative amount of turbulent kinetic energy associated with each mode. Back‐projecting the POD modes onto the velocity snapshots produces dynamic coefficients that express the amplitude of each mode in time. A reduced‐order model of the wind turbine wake (wakeROM) is defined through a series of polynomial parameters that quantify mode interaction and the evolution of each POD mode coefficients. The resulting system of ordinary differential equations models the wind turbine wake composed only of the large‐scale turbulent dynamics identified by the POD. Tikhonov regularization is used to recalibrate the dynamical system by adding additional constraints to the minimization seeking polynomial parameters, reducing error in the modeled mode coefficients. The wakeROM is periodically reinitialized with new initial conditions found by relating the incoming turbulent velocity to the POD mode coefficients through a series of open‐loop transfer functions. The wakeROM reproduces mode coefficients to within 25.2%, quantified through the normalized root‐mean‐square error.  A high‐level view of the modeling approach is provided as a platform to discuss promising research directions, alternate processes that could benefit stability and efficiency, and desired extensions of the wakeROM.     

Maximization of the annual energy production of wind power plants by optimization of layout and yaw‐based wake control

This paper presents a wind plant modeling and optimization tool that enables the maximization of wind plant annual energy production (AEP) using yaw‐based wake steering control and layout changes. The tool is an extension of a wake engineering model describing the steady‐state effects of yaw on wake velocity profiles and power productions of wind turbines in a wind plant. To make predictions of a wind plant's AEP, necessary extensions of the original wake model include coupling it with a detailed rotor model and a control policy for turbine blade pitch and rotor speed. This enables the prediction of power production with wake effects throughout a range of wind speeds. We use the tool to perform an example optimization study on a wind plant based on the Princess Amalia Wind Park. In this case study, combined optimization of layout and wake steering control increases AEP by 5%. The power gains from wake steering control are highest for region 1.5 inflow wind speeds, and they continue to be present to some extent for the above‐rated inflow wind speeds. The results show that layout optimization and wake steering are complementary because significant AEP improvements can be achieved with wake steering in a wind plant layout that is already optimized to reduce wake losses. Copyright © 2016 John Wiley & Sons, Ltd.