Optimization of Headspace Single-Drop Microextraction Coupled with Gas Chromatography–Mass Spectrometry for Determining Volatile Oxidation Compounds in Mayonnaise by Response Surface Methodology

In this assay, headspace single-drop microextraction (HS-SDME) coupled with gas chromatography–mass spectrometry (GC–MS) as a simple, low-cost and rapid method has been developed and validated for determining volatile oxidation compounds including hexanal and heptanal in mayonnaise. The main microextraction variables affecting the HS-SDME procedure such as extraction temperature and time, stirring rate, and amount of NaCl were optimized by response surface methodology employing a central composite design. Obtained results demonstrated that higher yield of extracted analytes could be achieved under the following optimal conditions: extraction temperature of 45 °C, extraction time of 16 min, stirring rate at 700 rpm, and addition of 2 g NaCl. The optimized HS-SDME/GC–MS method was validated for oxidized mayonnaise samples (50 °C/48 h) by calculating analytical parameters (linearity, precision, accuracy, and sensitivity). Good linearity (R ²?>?0.99) was observed by plotting calibration curves of extracted hexanal and heptanal over the concentration range of 0.025–10 μg g^?1, and the repeatability of the method, expressed as relative standard deviation, were found to be 4.04 % for hexanal and 3.68 % for heptanal (n?=?7). After the microextraction process of spiked mayonnaise sample, high levels of relative recovery were obtained for hexanal (107.33 %) and heptanal (91.43 %). The detection limits were 0.008 ng g^?1 and 0.021 ng g^?1 for hexanal and heptanal, respectively, while quantification limits of hexanal and heptanal were calculated to be 0.027 ng g^?1 and 0.071 ng g^?1, respectively. The possibility of the HS-SDME followed GC–MS to determine and quantify volatile oxidation compounds such as hexanal and heptanal was confirmed by analyzing commercial fresh mayonnaise stored at 4 and 25 °C during 3 months.     

A Rapid Determination of Ergosterol in Grains Using Gas Chromatography–Mass Spectrometry Method Without Derivatization

Food Analytical Methods - A simple, rapid and sensitive GC-MS method using on-column injection was developed and validated to determine ergosterol (ERG) levels in maize and wheat. In this method,...     

Simple Method for Determination of Fungicides in Citrus Fruits by Liquid Chromatography–Tandem Mass Spectrometry

A simple method for the determination of four fungicides (thiabendazole, imazalil, o-phenylphenol, and diphenyl) in citrus fruits has been developed. After spiking surrogates of these fungicides, the sample was extracted with acetonitrile, salted out, and the water was simultaneously removed using anhydrous magnesium sulfate and sodium chloride. The extract was first purified with a primary secondary amine and octadecylsilane, followed by the addition of dimethyl sulfoxide as a keeper solvent, and subsequently concentrated under a nitrogen stream. The compounds were analyzed by liquid chromatography–tandem mass spectrometry using the atmospheric pressure photoionization interface. The recoveries and relative standard deviations (RSDs) of the fungicides (1 mg kg^?1) were satisfactory (recovery 92–114 %; RSD <10 %). An evaluation with Shewhart QC plots revealed that all data points are within the controlled area, thus confirming the robustness of the method for analyzing the fungicide content of citrus fruits. The sample preparation time for ten samples was approximately 2 h, highlighting the time and labor efficiency of the method.     

Direct Chiral Determination of Acephate and Its Metabolite Methamidophos in Vegetables Using QuEChERS by Gas Chromatography–Tandem Mass Spectrometry

Currently, methamidophos, the main metabolite of acephate in the plants, has been paid particular attention in the risk evaluation of acephate because of its severely accurate toxicity, but the chirality of methamidophos and acephate has not been taken into account. In this study, a chiral separation and analysis method was developed to help evaluate the risks posing to the environment and human health. The efficiency of four commercial chiral capillary columns to accomplish enantioseparation of these two pesticides was firstly evaluated, and the chromatographic condition on the chose column BGB-176 SE was optimized. An analytical method for determination and confirmation of the enantiomers in vegetables by gas chromatography–tandem mass spectrometry was then developed with the column. QuEChERS was adopted to extract and clean the residues in vegetables. The mean recovery rates of quintuplicate results in cabbage and pakchoi ranged from 71.87 to 81.45 %; the relative standard deviation was less than 8.81 %. The limits of detection of enantiomers of acephate and methamidophos were 0.008 and 0.005 mg/kg, respectively. After the application of the method to vegetables from a market, it was proved that the metabolism of acephate and methamidophos in plants should be enantioselective.     

Determination of Chlorothalonil Residue in Cabbage by a Modified QuEChERS-Based Extraction and Gas Chromatography–Mass Spectrometry

Being susceptible to any matrix with pH >5, taking cabbage as an example, the low recovery of chlorothalonil residues adsorbed onto the cabbage matrix was almost completely improved by extracting with 1/1 (v/v) acetonitrile (containing 5 % acetic acid)/toluene. Under the optimized conditions, the recoveries of chlorothalonil in cabbage fortified at three concentrations of 0.5 to 10 mg kg^?1 were 71–93 % with relative standard deviations (RSDs) lower than 6 %. The limit of detection (LOD) and the limit of quantification (LOQ) of the gas chromatography–mass spectrometry (GC–MS) method for chlorothalonil were 0.05 and 0.5 mg kg^?1, respectively, which were much lower than the maximum residue limits (MRLs). The proposed analytical method demonstrated a potential for its application to monitor for chlorothalonil and to help assure food safety, especially base-sensitive-pesticide analysis.     

Dispersive Liquid–Liquid Microextraction Followed by Magnetic Solid-Phase Extraction for Determination of Four Parabens in Beverage Samples by Ultra-performance Liquid Chromatography Tandem Mass Spectrometry

In this study, a two-step extraction technique was developed for extraction and preconcentration of parabens from beverage samples using ionic liquid dispersive liquid–liquid microextraction (IL-DLLME) and magnetic solid-phase extraction (MSPE). In this IL-DLLME followed by MSPE method, ionic liquid (IL, 1-octyl-3-methylimidazolium hexafluorophosphate) formed hydrophobic microdroplets in beverage samples as an extractant of parabens; after the IL-DLLME process was completed, graphene modified Fe₃O₄ nanoparticles (Fe₃O₄@G) were placed to adsorb and isolate IL from the sample solution. After the supernatant was carefully moved, acetonitrile was added to elute the IL containing parabens from Fe₃O₄@G. The experimental variables affecting the extraction procedure have been systematically studied. Under optimal conditions, the detection limits were less than 1.53 ng/mL and the linear detection ranges were 2–500 ng/mL (R ² ≥ 0.998) for these analytes. The recoveries for spiked samples were 58.8–89.2% and satisfactory precision (RSD ≤ 4.8%) were obtained.     

Determination of Triazoles in Tea Samples Using Dispersive Solid Phase Extraction Combined with Dispersive Liquid–Liquid Microextraction Followed by Liquid Chromatography–Tandem Mass Spectrometry

In this study, dispersive solid phase extraction (DSPE) combined with dispersive liquid–liquid microextraction (DLLME) method was developed for the determination of triazole fungicide residues in tea samples. DSPE with ODS C₁₈, primary secondary amine, and florisil as sorbents was applied to clean up and minimize matrix interference from tea samples; it was followed with the enrichment of target compounds in the DLLME procedure and detection with liquid chromatography–tandem mass spectrometry (LC-MS/MS). The effects of various experimental parameters on the DSPE and DLLME procedures were studied systematically, such as the kinds and volume of sorbents, extraction and dispersive solvents, and extraction time. Under optimum conditions, the method was validated in a tea matrix. The matrix-matched calibration curves of three triazoles had good linearity in the range of 0.0125–50 μg kg^?1, and the linear regression coefficients (r) ranged from 0.9998 to 0.9999. The limits of quantification (S/N?=?10) for penconazole, tebuconazole, and triadimenfon were 4.0, 7.8, and 31.6 ng kg^?1, respectively. The intra-day and inter-day relative standard deviations varied from 3.6 to 18.6 %. Recoveries in three concentration levels were between 91 and 118 %. The obtained results show that the proposed DSPE-DLLME-LC-MS method has the potential to analyze trace fungicides in a complex sample matrix.     

Determination of Selected Polychlorinated Biphenyl Residues in Meat Products by QuEChERS Method Coupled with Gas Chromatography–Mass Spectrometry

Polychlorinated biphenyl (PCB) residues in food are an important food safety concern. Simple and sensitive analytical methods are needed to monitor PCB residues and ensure that food is safe for consumption. The aim of this study was to adapt a selective, sensitive, quick, and easy sample treatment for purification of animal fat matrices and to measure the level of PCB28, PCB52, PCB101, PCB118, PCB138, PCB153, and PCB180 in samples of meat products (salami, soudjouk, and sausage) produced in Turkey. The extraction and purification of meat products were performed via the modified quick, easy, cheap, effective, rugged, and safe (QuEChERS) method and PCB levels determined by gas chromatography–mass spectrometry. The linearity was satisfactory for all compounds studied, with correlation coefficients ≥0.99. The limits of determination and the limits of quantification were in the range of 0.144–0.382 and 0.479–1.274 ng g^?1, respectively. Recovery at 3 different spiking concentrations was 95.7–101 % and the relative standard deviations were <3.5 %. This validated method was observed to be more economic and eco-friendly, as it uses a smaller volume of extraction solvents that are also less toxic. The validated method was successfully applied to the analysis of selected PCBs in meat products with satisfactory results. The method’s results indicated the presence of PCBs in some of the meat product samples, although the levels were below the maximum residue limit for food products of animal origin in Turkey (40 ng g^?1 of fat), which is in accordance with EU and Turkish levels.     

Application of Fast Gas Chromatography–Mass Spectrometry in Combination with the QuEChERS Method for the Determination of Pesticide Residues in Fruits and Vegetables

A fast gas chromatography–mass spectrometry method has been developed for multiresidue determination of up to 56 pesticides in fruits and vegetables in a chromatographic run time of <10 min, using a single quadrupole mass spectrometer operating in selected ion monitoring mode. The well-known acetate-buffering version of the QuEChERS method has been used for sample preparation. Programmable temperature vaporizer injection of 3 μL allowed reaching limits of detection between 0.15 and 15 μg/kg for most compounds in the sample matrices tested. The applicability of the method has been evaluated in apple, orange, carrot, and tomato. Recoveries at three fortification levels (0.01, 0.1 and 0.5 mg/kg) ranged from 70 to 120 % for most compounds, with relative standard deviations below 20 % in all cases. The developed method has been applied to fruit and vegetable samples from different Spanish provinces.     

Analysis of Peanut Using Near-Infrared Spectroscopy and Gas Chromatography–Mass Spectrometry: Correlation of Chemical Components and Volatile Compounds

Peanut contains protein, oil, oleic acid, and linoleic acid its flavor is largely determined by pyrazine and aldehyde compounds. Both nutritional value and flavor are standards for measuring peanut quality. In this report, the contents of protein, oil, oleic acid, and linoleic acid were determined using near-infrared reflectance spectroscopy, and flavor compounds were identified using headspace solid-phase microextraction combined with gas chromatography–mass spectrometry in 12 different peanut cultivars. Our results showed that the content of oleic acid in raw peanut ranged from 35.69 to 82.79 g/100 g oil and the linoleic acid content ranged from 2.92 to 44.19 g/100 g oil, with high coefficients of variation. The coefficients of variation of protein and oil were lower, with content of 26.97–33.07 g/100 g raw materials and 45.53–55.53 g/100 g raw materials, respectively. Overall, 14 volatile components were isolated and identified, among which pyrazine and aldehyde compounds were the major aroma components in 12 different peanut cultivars.. Based on these results, peanuts with high protein content have high linoleic oil levels but low oleic oil levels, and roasted peanuts have a high content of pyrazines but low content of aldehydes. The results of this study will enable manufacturers to develop simple tests that predict the flavor of roasted peanuts based on their composition.     

Application and Optimization of Microwave-Assisted Extraction and Dispersive Liquid–Liquid Microextraction Followed by High-Performance Liquid Chromatography for the Determination of Oleuropein and Hydroxytyrosol in Olive Pomace

In the present study, a new method based on microwave-assisted extraction and dispersive liquid–liquid microextraction (MAE–DLLME) followed by high-performance liquid chromatography (HPLC) was proposed for the separation and determination of oleuropein (Ole) and hydroxytyrosol (HyT) from olive pomace samples. The effective factors in the MAE–DLLME process such as microwave power, extraction time, the type and volume of extraction, and dispersive solvents were studied and optimized with the aid of response surface methodology (RSM) based on a central composite design (CCD) to obtain the best condition for Ole and HyT extraction. At the optimized conditions, parameter values were 220 W microwave power, 12 min extraction time, 60 μL extracting solvent, and 500 μL dispersive solvent. The calibration graphs of the proposed method were linear in the range of 10–500,000 μg L^?1, with the coefficient of determination (R²) higher than 0.99 for Ole and HyT. Repeatability of the method, described as the relative standard deviation (RSD), was 4.12–5.63% (n?=?6). The limits of detection were 35 and 20 μg L^?1 for Ole and HyT, respectively. The recoveries of these compounds in the spiked olive pomace sample were from 93 to 98%. The proposed method, MAE–DLLME–HPLC–UV, was an accurate, rapid, and reliable method when compared with previous methods.     

A Rapid and Sensitive Method for Determination of Melamine in Fish,Shrimp, Clam,and Winkle by Gas Chromatography–Mass Spectrometry with Microwave-Assisted Derivatization

A method for rapid and sensitive determination of melamine in aquatic products by gas chromatography–mass spectrometry with microwave-assisted derivatization was proposed in this paper. Melamine was extracted from aquatic product samples using methanol, and the extract was cleaned with a mixed-mode cationic exchange solid phase extraction column. After elution with 5 % ammonia–methanol solution and drying with nitrogen, the residue was derivatized using N,O-bis(trimethylsilyl)trifluoroacetamide containing 1 % trimethylchlorosilane under microwave irradiation for 1 min with a power of 420 W, then detected with gas chromatography–mass spectrometry, and quantified by the external standard method. Some important parameters such as extraction solvent, microwave irradiation power and time, and derivatization reagent volume were investigated and optimized. The results showed that methanol could effectively extracted melamine from aquatic products as well as precipitated the protein in samples. Under the optimum conditions, the detection limit for melamine was as low as 0.006 mg/kg, and the linear range was from 0.02 to 50 mg/kg with a correlation coefficient of 0.9997. The proposed method was applied to the analysis of melamine in aquatic products (fish, shrimp, clam, and winkle), and the recovery for melamine was 89.65–105.16 % with relative standard deviation of 3.0–6.0 %.     

Comparison of Simple and Rapid Extraction Procedures for the Determination of Pesticide Residues in Fruit Juices by Fast Gas Chromatography–Mass Spectrometry

Three sample treatment methods, based on QuEChERS, solid-phase extraction (SPE) and solid-phase microextraction (SPME), were compared and evaluated in order to obtain the best conditions to determine pesticide residues in fruit juice by fast gas chromatography–mass spectrometry (single quadrupole GC-MS). Analysis were performed under selected ion monitoring, acquiring the three most abundant and/or specific ions for each analyte and using their relative intensity ratios as a confirmatory parameter. The 3 methodologies (QuEChERS, SPE and SPME) were validated taking 15 selected pesticides as model compounds, using commercial apple juice. QuEChERS procedure was based on the AOAC Official Method 2007.01, using acetonitrile (containing 1 % acetic acid) as extraction solvent and primary–secondary amine during the dispersive solid-phase extraction. Oasis hydrophilic–lipophilic balance cartridges were used for SPE, and polyacrylate fibers were used for direct immersion SPME procedure. Three isotopically labeled standards were added to the samples before extraction and used as surrogate standards. Validation parameters as recoveries, limits of detection, and limits of quantification (LOQ), as well as matrix effects and sample throughput, were obtained and compared for the three extraction procedures. QuEChERS was considered faster and led to the best quantitative results. In this way, validation was extended to up to 56 pesticides by applying QuEChERS in multi-fruit juice samples, obtaining LOQs ranging from 2 to 20 μg/L for most compounds. Accuracy and precision were evaluated by means of recovery experiments at two concentration levels (10 and 100 μg/L), obtaining recoveries between 70 and 120 % in most cases and relative standard deviations below 15 %. Finally, the QuEChERS method was applied to the analysis of commercial juices, including mango–apple, pineapple, grapefruit and orange.     

Determination of Triazole Fungicides in Vegetable Samples by Magnetic Solid-Phase Extraction with Graphene-Coated Magnetic Nanocomposite as Adsorbent Followed by Gas Chromatography–Mass Spectrometry Detection

A graphene-based magnetic nanocomposites (G-Fe₃O₄ MNPs) was synthesized and used as the adsorbent for the extraction of some triazole fungicides (triadimefon, paclobutrazol, hexaconazole, myclobutanil, diniconazole, propiconazole, and tebuconazole) in cucumber, cabbage, and tomato samples prior to gas chromatography–mass spectrometry detection. Various experimental parameters affecting the extraction efficiencies, such as the amount of G-Fe₃O₄ MNPs, extraction time, pH and salt concentration of the sample solution, and desorption conditions were investigated. Under the optimized experimental conditions, the enrichment factors of the method for the analytes were in the range from 461 to 697. The signal response was linear in the range of 0.5–35.0 ng g^?1 for all the analytes with the correlation coefficients ranging from 0.9810 to 0.9986. The limits of detection (S/N?=?3) of the method for the analytes were between 0.01 and 0.10 ng g^?1. The recoveries of the method for the seven triazoles were in the range from 84.4 to 108.2 % with RSDs between 3.4 and 10.6 %.     

Analysis of Infant Formula for Steroid Hormones by Gas Chromatography–Tandem Mass Spectrometry Using Microwave-Assisted Extraction and Gel Permeation Chromatography Clean Up

A new method was developed for effective separation and simultaneous determination of estrogens, gestagens, and androgens, including estrone, 17β-estradiol, testosterone, progesterone, and estriol, in infant formula. The samples were enzymatically digested with β-glucuronidase/arylsulfatase prior to microwave-assisted extraction. After the extract was cleaned up by gel permeation chromatography the hormones were derivatived with 50 μL BSTFA containing 1 % TMCS. The derivatived hormones were measured with GC–MS/MS using electron impact ionization source in the positive multi-reaction monitoring mode. The calibration curves showed good linearity with correlation coefficient (r) of >0.999. The limit of quantification of five hormones ranged from 0.094 to 0.265 μg kg^?1, which is below the minimum required performance limits established by the European Community. The intra- and inter-day precision (as RSD) for six determinations of five analytes at 40 μg kg^?1 spiked level was in range of 3.4–5.4 % and 3.5–6.8 %, respectively. The recovery of five analytes was obtained to be 84.5–104 %, with relative standard deviations (RSD, n?=?6) of 1.7–5.5 %. This method has been successfully used for the qualitatively and quantitatively determination of estrone, 17β-estradiol, testosterone, progesterone, and estriol in infant formula.     

Determination of Amoxicillin Stability in Chicken Meat by Liquid Chromatography–Tandem Mass Spectrometry

An amoxicillin stability study was performed under different pH (1, 3 and 5) and temperature (4 °C, 22 °C, 37 °C and 55 °C) conditions and for incurred samples stored at −20 °C with the goals of better understanding amoxicillin degradation and characterising its main degradation products (amoxicilloic acid and amoxicillin diketopiperazine). The analytical methodology used consisted of a simple extraction using phosphate buffer (pH 8) with sodium chloride followed by a sample clean-up using OASIS? HLB cartridges and a liquid chromatography–tandem mass spectrometric analysis. Amoxicillin was found to be greatly unstable at temperatures above 22 °C for all pH values studied, so it was recommended that biological samples should be frozen at temperatures below −70 °C until analysis of the amoxicillin residues.     

Modified QuEChERS Combination with Magnetic Solid-Phase Extraction for the Determination of 16 Preservatives by Gas Chromatography–Mass Spectrometry

In this paper, based on the mechanism of the quick, easy, cheap, effective, rugged and safe (QuEChERS) method, a novel graphene grafted silica-coated Fe₃O₄ (Fe₃O₄@SiO₂@G) was synthesized and applied as the efficient magnetic solid-phase extraction (MSPE) adsorbent for rapid cleanup of vegetable samples prior to analyzing 16 preservative residues by gas chromatography–mass spectrometry (GC-MS). The method, which took advantages of the novel nanoparticle adsorbent and an external magnetic field separation targets from samples, not only could avoid the time consuming of the traditional solid-phase extraction, but also could be developed for simultaneous determination of 16 preservative residues in vegetables. Various experimental parameters that could affect the extraction efficiencies have been investigated. Under the optimum conditions, 16 preservatives showed good linearity over the range of 0.02–2.00 mg/L and correlation coefficients (R ²) of 0.9946–0.9998. The limits of detections (LODs) were in the range of 0.21–11.50 μg/kg. The recoveries of 16 preservatives ranged from 78.3 to 116.7 %, and the relative standard deviations (RSDs) ranged from 1.4 to 11.9 %.     

Multi-Objective Optimization of Osmotic–Ultrasonic Pretreatments and Hot-Air Drying of Quince Using Response Surface Methodology

In this study, application of a multi-objective optimization technique based on response surface methodology has been presented. Quince slices were dehydrated using osmotic dehydration with sucrose solutions at different concentration (40 and 60 Brix), processing time (1, 1.5, and 2 h), and ultrasonication time (0, 15, and 30 min) were the factors investigated with respect to water loss, solid gain, and weight reduction. Response surface methodology was used to determine the optimum processing conditions that yield maximum water loss and weight reduction and minimum solid gain during osmotic dehydration of quinces. Dehydrated quince slices at optimized osmo-ultrasound condition were then subjected to air-drying at 60 and 80 °C. Rehydration ratio, shrinkage, and moisture content of dried samples were regarded as responses to the non-thermal and air-drying conditions. Multi-objective optimization led to obtaining the best condition for production of dried quince slices with lowest moisture content, and shrinkage.     

Investigation of Levels and Fate of Pyridalyl in Fruit and Vegetable Samples by Fast Gas Chromatography–Mass Spectrometry

The search on pyridalyl residues, the novel insecticide, in strawberries and spring onions was evaluated. The QuEChERS technique was used for sample preparation. A fast gas chromatography–mass spectrometry (GC–MS) method was developed and validated for the analysis of pyridalyl in both matrices. Fast GC–MS was performed with a narrow-bore capillary column and a quadrupole mass detector with electron ionization and negative chemical ionization, both operating in selected ion monitoring mode. Fortification studies at 1, 5, 10, and 250 μg/kg for fruit and vegetable matrices were performed. Recoveries for all fortification levels, two ionization modes ranged from 72 to 114 %. Matrix effects were discussed. Limits of quantification were established at 1 μg/kg. Field experiments to investigate the pre-harvest interval were carried out. The proposed method was applied successfully to the determination of pyridalyl residues in samples available on Slovak market, and none of the samples contained detectable amounts of pesticides. The developed method is simple, efficient, and easy to adopt in laboratories engaged in pesticide residue analysis method.