High-Performance Directional Metallopolyamides. I. Synthesis and Thermal Analysis

High-performance polyamides containing the 4,4-disubstituted-2,2-bipyridyl moiety were synthesized by phosphorylation polycondensation from 2,2-bipyridyl-4,4-dicarboxylic acid and a series of primary aromatic diamines with triphenylphosphite and pyridine as the agents to facilitate condensation. Polyamides exhibiting improved solubility in organic solvents and strong acids, melting transitions at low temperatures, and good thermal properties were prepared by introducing bulking methyl and fluoro groups and flexible ether and propyl linkages and by using monomers with reduced symmetry. Solutions of the polyamides with rigid main chains (III, IV, V, VI, and VIII) showed birefringence (colorful spherulites) at concentrations of 5, 10, and 15% (w/v) polymer/solvent. The chelation of ruthenium(II) ions resulted in the preparation of directional metallopolyamide systems based on the geometrically favorable tris(2,2-bipyridyl)ruthenium(II) complex. The three-dimensional polyamides, which absorbed at a _max of 476 mm and emitted at a _max of 620 nm, exhibited a high thermal stability and improved solubility, making them suitable candidates for compressive strength studies and cyclic voltammetry studies as part of an effort to address the corrosion of graphite fiber-reinforced composites.     

Shape-Selective Alkylation of Biphenyl over H-[Al]-SSZ-31 with Propylene

Isopropylation of biphenyl (BP) over [Al]-SSZ-31, a large-pore, one-dimensional zeolite has been studied. Effects of temperature, pressure and SiO₂/Al₂O₃ ratio were examined. SSZ-31 was found to be an active catalyst in the isopropylation of biphenyl with propylene. The selectivity for 4-isopropylbiphenyl (4-IPBP) and 4,4-diisopropylbiphenyl (4,4-DIPB) was high among isopropylbiphenyl (IPBP) and diisopropylbiphenyl (DIPB) isomers, respectively, indicating SSZ-31 shows shape-selective catalysis. The selectivity for 4,4-DIPB decreased with temperature increase; correspondingly the selectivity for thermodynamically more stable isomers (3,3- and 3,4 DIPB) increased with temperature. The yield of IPBP isomers decreased while that of DIPB isomers increased with temperature increase. Pressure showed less effect on conversion; however, increase in pressure suppresses the isomerization of 4,4-DIPB to 3,3- and 3,4-DIPB. Conversion decreased with increase in SiO₂/Al₂O₃ ratio. At low SiO₂/Al₂O₃ ratio of 136, relatively high triisopropylbiphenyl (TriIPB) isomers were formed in bulk products and their amount decreased with increase in SiO₂/Al₂O₃ ratio.     

Synthesis, Characterization and Optimum Reaction Conditions of Oligo-N, N′-bis (2-hydroxy-1-naphthalidene) Thiosemicarbazone

The oxidative polycondenzation reaction conditions of N, N-bis (2-hydroxy-1-naphthalidene) thiosemicarbazone (HNTSC) using air oxygen, H₂O₂ and NaOCl were studied in an aqueous alkaline medium between 50–90°C. Oligo-N, N-bis (2-hydroxy-1-naphthalidene) thiosemicarbazone was characterized by ¹H-NMR, FT-IR, UV-Vis, size exclusion chromatography (SEC) and elemental analysis techniques. Solubility testing of oligomer was investigated using organic solvents such as DMF, THF, DMSO, methanol, ethanol, CHCl₃, CCl₄, toluene acetonitrile, ethyl acetate, concentrated H₂SO₄ and an aqueous alkaline solution. Using NaOCl, H₂O₂ and air O₂ oxidants, conversion to oligo-N, N-bis (2-hydroxy-1-naphthalidene) thiosemicarbazone (OHNTSC) of N, N-bis (2-hydroxy-1-naphthalidene) thiosemicarbazone was found to be 85, 80 and 76%, respectively, in an aqueous alkaline medium. According to the SEC analyses, the number-average molecular weight, weight-average molecular weight and polydispersity index values of OHNTSC synthesized were found to be 1050 gmol^–1 1715 gmol^–1 and 1.63, using NaOCl, and 2137, 2957 gmol^–1 and 1.38, using air O₂ and 2155 gmol^–1 4164 gmol^–1 and 1.93, using air H₂O₂, respectively. Also, TG analysis was shown to be unstable of oligo-N, N-bis (2-hydroxy-1-naphthalidene) thiosemicarbazone against thermo-oxidative decomposition. The weight loss of OHNTSC was found to be 97.29% at 900°C.     

Shape-selective isopropylation of biphenyl over a highly dealuminated mordenite: effect of propylene pressure

A highly dealuminated H-mordenite (H-M) catalyzed the selective isopropylation of biphenyl to 4,4-diisopropylbiphenyl (4,4-DIPB). The high selectivity is ascribed to the shape-selective catalysis in mordenite pores. The selectivity of 4,4-DIPB decreased during the isopropylation of biphenyl due to isomerization of 4,4-DIPB under low propylene pressure. The increase of propylene pressure suppressed the isomerization in the isopropylation. 4,4-DIPB itself was isomerized over highly dealuminated H-M under low propylene pressure.     

Heterogeneous asymmetric reactions. 23. Enantioselective hydrogenation of ethyl pyruvate over cinchonine- and α-isocinchonine-modified platinum catalysts

The enantioselective hydrogenation of ethyl pyruvate to (S)-ethyl lactate over cinchonine- and -isocinchonine-modified Pt/Al₂O₃ catalysts was studied as a function of modifier concentration and reaction temperature. The maximum enantioselectivities obtained under the applied mild conditions were 89% ee using cinchonine (0.014 mmoldm^–3, 1 bar H₂, 23°C, 6% AcOH in toluene), and 76% ee in the case of -isocinchonine (0.14 mmoldm^–3, 1 bar H₂, –10°C, 6% AcOH in toluene). Since -isocinchonine of rigid structure exists only in anti-open conformation these data provide additional experimental evidence to support the former suggestion concerning the dominating role of anti-open conformation in these cinchona-modified enantioselective hydrogenations.     

Chemical modification of copoly(methylsilylene/1,4-phenylene) by Pt-catalyzed hydrosilation reactions with functionally substituted alkenes

Copoly(methyl-3-biphenoxypropylsilylene 1,4-phenylene), copoly(methyl-3-cyanopropylsilylene 1,4-phenylene), copoly(methyl-3-ethoxypropylsilylene 1,4-phenylene), copoly(methyl-3-phenoxypropylsilylene 1,4-phenylene), and copoly(methyl-4,7,10,13-tetraoxatetradecanylsilylene 1,4-phenylene) have been prepared by platinum-catalyzed hydrosilation graft reactions between poly (methylsilylene 1,4-phenylene) and appropriate functionally substituted alkenes. These polymers have been characterized by¹H,¹³C, and²⁹Si NMR as well as by FT-IR and UV-vis spectroscopy. The molecular weight distribution of these polymers has been determined by gel permeation chromatography (GPC), and their glass transition temperatures (T _e) by DSC.     

Silyl Triflate-Initiated Ring-Opening Polymerizations of Cyclosiloxanes

Polymer yields between 70 and 85% form in ring-opening polymerizations of trimeric cyclosiloxanes initiated with trimethylsilyl triflate in the presence of a selective scavenger for protic acids, 2,6-di-t-butylpyridine. Examples include the polymerization of 1,3,5-trimethyl-1,3,5-tris(3,3,3-trifluoropropyl)cyclotrisiloxane (F₃) and hexamethylcyclotrisiloxane (D₃). Siloxane bond redistribution is essentially absent and data are presented establishing a nonterminating polymerization giving an average of roughly one trimethylsilyl group per chain. The present observations contrast with other work that suggests that the presence of free triflic acid is required for initiation with trimethylsilyl triflate.     

Preparation of Linear π-Conjugated Coordination Polymers Having Ruthenium(II) Complex in the Main Chain

Soluble -conjugated coordination polymers having a ruthenium(II) complex in the main chain were prepared from a soluble metal complex monomer and a bridging ligand via coordination. Refluxing of an ethanol-water suspension containing (4,4-dinonyl-2,2-bipyridyl)Ru(III) with 2,3-bis(2-pyridyl)pyrazine gave the coordination polymer. The resulting polymer was soluble in common organic solvents. The structure was confirmed by uv/vis spectra and gpc analysis.     

Mechanisms of Iron Activation on Fe-Containing Zeolites and the Charge of α-Oxygen

According to previous Mössbauer data [1] -sites formation at the activation of Fe-containing zeolites is accompanied by irreversible self-reduction of the iron, proceeding without participation of an external reducing agent. Reduced Fe²⁺ ions are inert to O₂ but are reversibly oxidized to Fe³⁺ by N₂O, generating the -oxygen species, O, which provide selective oxidation of hydrocarbons.In this work, the mechanism of -sites formation was studied via quantitative measurement of the dioxygen amount desorbed into the gas phase at the step of self-reduction. A prominent role of the zeolite matrix chemical composition has been revealed. For example, with zeolites of Al–Si composition (FeZSM-5 and Fe-), heating to 900 °C in a closed vacuum space leads to irreversible evolution of O₂, which is accompanied by the immediate formation of -sites. Similar heating of B–Si and Ti–Si zeolites also leads to dioxygen evolution; however, this evolution is reversible and is not accompanied by formation of -sites. Activation of these zeolites occurs only in the presence of water vapor. Stoichiometric measurements showed that in terms of charge one regular O^2- ion, removed at the activation, is equivalent to two -oxygen atoms. So, -oxygen is identified as an ion-radical species O ^-., whose unique oxidation properties still distinguish it from the generally observed O^-. radicals.The mechanism of -sites formation is proposed, in which the process of strong chemical stabilization of reduced Fe²⁺ atoms in the zeolite structure is a key step, making impossible the reoxidation of the iron with O₂.     

Synthesis and properties of aromatic polyesters and brominated polyesters derived from α,α′-bis(4-hydroxyphenyl)-1,4(or 1,3)-diisopropylbenzene

The interfacial polycondensation technique was used for the preparation of polyarylates and brominated polyarylates. Polyarylates and brominated polyarylates were prepared by mixing a solution of diacid chloride such as terephthaloyl chloride, isophthaloyl chloride, or their mixture in dichloromethane with an aqueous alkaline solution of ,-bis(4-hydroxyphenyl)-1,4(or 1,3)-diisopropylbenzene or ,-bis(4-hydroxy-3,5-dibromophenyl)-1,4(or 1,3)-diisopropylbenzene using triethylbenzylammonium chloride as the phase transfer agent. Moderate to high molecular weight polyarylates with _inh up to 1.27 dL/g were obtained, and most of them could be cast into tough and flexible films depending on the polymer composition. In general, polymers containing more 1,3-isomer or isophthaloyl chloride moieties gave transparent and flexible films and had lower glass transition temperatures and higher solubility. Although these polymers have two isopropylidene linkages in their repeating units, they still exhibit moderately high thermal stability and show no obvious weight loss before 400 °C. The introduction of bromine on the polymer backbone caused a decrease of inherent viscosity, crystallinity, and thermal stability of the polyarylates, while causing an increase in glass transition temperature and a great enhancement of fire retardancy.     

Electrosynthesis of 4,4′-dinitroazobenzene on PbO2 electrodes

Parameters which affect the electrosynthesis of 4,4-dinitroazobenzene from p-nitroaniline on platinum and PbO₂ electrodes were investigated and optimum conditions were determined. Maximum conversion efficiency for electrosynthesis was 95% with a pure -PbO₂ electrode. It was found that the electrocatalytic activity of a PbO₂ electrode depends upon its / ratio and its degree of crystallinity. The effects of the added base and water on the conversion efficiency were also elucidated.     

Local study of wall to liquid mass transfer in fluidized and packed beds. II. Mass transfer in packed beds

Mass and momentum transfer at a wall in liquid-particle systems are studied with a two-dimensional model which consists of fixed spherical turbulence promoters arranged in a simple cubic lattice in a rectangular channel. Local values of the mass transfer coefficient and shear stress at a wall of the channel have been measured at identical locations. The results show that there are large differences between the local values but their distribution along the transfer surface is reproduced identically. The dependence of these local values on each other allows one to obtain a general relationship between overall mass and momentum transfer as well as a correlation of mass transfer results for exchange between a wall and a flowing liquid in a fixed bed of particles.Nomenclature a _g particle specific area - a coefficient in expression s=a ^q (q>0) - a, b coefficients in expressionJ _M=a(Re) ^–b - d _p particle diameter - d microelectrode diameter - D molecular diffusion coefficient - h _K,h _B constants in Ergun equation - J _M=(¯k/u/)(Sc) ^2/3 Colburnj-factor - k local mass transfer coefficient - k local mass transfer coefficient in inert wall - ¯k overall mass transfer coefficient - L length of the transfer surface - q exponent in expressions=a ^q - (Re)=(ud _p)/[v(1-)] modified Reynolds particle number - (Sc)=v/D Schmidt number - s, ¯s velocity gradients at the wall - u superficial liquid velocity - coefficient in Equation 1 - characteristic length - bed porosity - _F fluid density - dynamic viscosity - kinematic viscosity - shear stress at the wall - P/L fluid pressure gradient     

Synthesis of soluble polyarylenes containing alternating 4,4′-(1,1′-binaphthyl) and 4,4′-(3,3′-diphenyl)biphenyl structural units

Summary The synthesis and Ni(0) catalyzed homocoupling polymerization of 4,4-bis[5-(trifluoromethanesulfonyloxy)-2-biphenylyl]-1, 1-binaphthyl (9) are described. This polymerization reaction produces a soluble polyarylene containing alternating 4,4-(1,1-binaphthyl) and 4,4-(3,3-diphenyl)biphenyl structural units.     

Syntheses and optical properties of <Emphasis Type="Italic">α</Emphasis>- and <Emphasis Type="Italic">β</Emphasis>-cyano-poly(<Emphasis Type="Italic">p</Emphasis>-phenylene vinylene) derivatives

Two light emitting molecules with the cyano group at different positions on the vinylene i.e., 2,5-bis(2-thienyl-1-cyanovinyl)-1-(2_-ethylhexyloxy)-4-methoxybenzene (-TPT) and 2,5-bis(2-thienyl-2-cyanovinyl)-1-(2-ethylhexyloxy)-4-methoxybenzene (-TPT), and corresponding polymers, i.e., poly[2,5-bis(2-thienyl-1-cyanovinyl)-1-(2-ethylhexyloxy)-4-methoxybenzene] (denoted as P1) and poly[2,5-bis(2-ethienyl-2-cyanovinyl)-1-(2-ethylhexyloxy)-4-methoxybenzene] (denoted as P2) were synthesized. -TPT and -TPT, respectively, were blended into two host polymers, poly(methyl methacrylate (PMMA) and poly(9-vinylcarbazole) (PVK), to study the optical properties of the dopants in different host polymer matrices. Although -TPT and -TPT have the same backbone structure, their optical properties are much different. The PL emission maximum ( _max) of -TPT was found blue-shifted, compared with that of -TPT, while the PL intensity of -TPT was stronger than that of -TPT. Concentration effect in the optical properties was found, 1 wt% of -TPT in PVK had the maximum fluorescent emission.The PL maximum peak wavelengths for polymer films (P1 and P2) were found red-shifted; while their PL intensities were weaker when compared with those of blends.     

Geographic variation of natural products of tropical nudibranch Asteronotus cespitosus

Extracts of the dorid nudibranch Asteronotus cespitosus from two geographically separate regions of Australia and from the Philippines were compared using thin-layer, high-performance liquid and gas chromatography and ¹H NMR analysis. Halogenated metabolites were detected in all mollusk specimens. The major component detected in digestive tissue of specimens from the Great Barrier Reef in northeastern Australia was 4,6-dibromo-2-(2,4-dibromophenoxy)phenol (1), with minor amounts of 3,5-dibromo-2-(3,5-dibromo-2-methoxyphenoxy)phenol (2). In a specimen collected from northwestern Australia, only 3,5-dibromo-2-(3,5-dibromo-2-methoxyphenoxy)phenol was found. The specimen from the Philippines contained 2,3,4,5-tetrabromo-6-(2-bromophenoxy)phenol (3) together with a novel chlorinated pyrrolidone (4). In addition, the sesquiterpenes dehydroherbadysidolide (5) and spirodysin (6) were detected in the digestive organs and mantle tissue of the nudibranchs from the Great Barrier Reef and from the Philippines, whereas these chemicals were not found in the specimen from northwestern Australia. All of the chemicals (1-3,5, and 6) have previously been isolated from the sponge Dysidea herbacea, as have chlorinated metabolites related to 4. This is the first time the characteristic halogenated metabolites that typify Dysidea herbacea have been reported from a carnivorous mollusk, which implies a dietary origin as opposed to de novo synthesis.     

Kinetics of copper electrodeposition in citrate electrolytes

The kinetics of copper electrocrystallization in citrate electrolytes (0.5M CuSO₄, 0.01 to 2M sodium citrate) and citrate ammonia electrolytes (up to pH 10.5) were investigated. The addition of citrate strongly inhibits the copper reduction. For citrate concentrations ranging from 0.6 to 0.8 M, the impedance plots exhibit two separate capacitive features. The low frequency loop has a characteristic frequency which depends mainly on the electrode rotation speed. Its size increases with increasing current density or citrate concentration and decreases with increasing electrode rotation speed. A reaction path is proposed to account for the main features of the reduction kinetics (polarization curves, current dependence of the current efficiency and impedance plots) observed in the range 0.5 to 0.8 M citrate concentrations. This involves the reduction of cupric complex species into a compound that can be either included as a whole into the deposit or decomplexed to produce the metal deposit. The resulting excess free complexing ions at the interface would adsorb and inhibit the reduction of complexed species. With a charge transfer reaction occurring in two steps coupled by the soluble Cu(I) intermediate which is able to diffuse into the solution, this model can also account for the low current efficiencies observed in citrate ammonia electrolytes and their dependencies upon the current density and electrode rotation speed.Nomenclature b, b ₁, b ₁ ^* Tafel coefficients (V^–1) - bulk concentration of complexed species (mol cm^–3) - (si*) concentration of intermediate C^* atx=0 (mol cm^–3) - C concentration of (Cu Cit H)^2– atx=0 (mol cm^–3) - C C variation due to E - C concentration of complexing agent (Cit)^3- at the distancex (mol cm^–3) - C _o concentrationC atx=0 (mol cm^–3) - C _o C _o variation due to E - Cv _s bulk concentrationC (mol cm^–3) - (Cit H), (Cu), (Compl) molecular weights (g) - C _dl double layer capacitance (F cm^–2) - D diffusion coefficient of (Cit)^3- (cm²s^–1) - D ₁ diffusion coefficient of C^* (cm²s^–1) - E electrode potential (V) - f ₁ frequency in Equation 25 (s^–1) - F Faraday's constant (96 500 A smol^–1) - i, i ₁, i ₁ ^* current densities (A cm^–2) - i i variation due to E - Im(Z) imaginary part ofZ - j - k ₁, k ₁ ^* , K₁, K ₁ ^* , K₂, K rate constants (cms^–1) - K rate constant (s^–1) - K ₃ rate constant (cm³ A^–1s^–1) - R _t transfer resistance (cm²) - R _p polarization resistance (cm²) - Re(Z) real part ofZ - t time (s) - x distance from the electrode (cm) - Z _f faradaic impedance (cm²) - Z electrode impedance (cm²) Greek symbols maximal surface concentration of complexing species (molcm^–2) - thickness of Nernst diffusion layer (cm) - , ₁, ₂ current efficiencies - angular frequency (rads^–1) - electrode rotation speed (revmin^–1) - =K ^–1(s) - _d diffusion time constant (s) - electrode coverage by adsorbed complexing species - (in0) electrode coverage due toC _s - variation due to E     

Thermophysical and elastomechanical properties of grainy corundum-zircon refractories and the effect of these properties on the thermal-shock resistance

Conclusions The thermophysical properties (l/l ₀ and ) and the elastomechanlcal properties (E, G, _bend) of corundum-zircon specimens in the 20–1200°C interval with various concentrations and grain sizes of zircon and different grain sizes and types of the corundum and zircon components in the grain and bondings have been investigated. It is established that in particular temperature regions there is a connection between the criteria R and R calculated from the values of the properties and the number of heat changes before the onset of primary cracking and total destruction of the specimens.Translated from Ogneupory, No. 1, pp. 56–60, January, 1980.     

Catalytic Methoxycarbonylation of Aromatic Diamines with Dimethyl Carbonate to Their Dicarbamates Using Zinc Acetate

The methoxycarbonylation of 2,4-toluene diamine and 4,4-diphenylmethane diamine with dimethyl carbonate to the corresponding dicarbamates using zinc acetate was carried out at 453 K. Zn(OAc)₂, prepared by evacuating Zn(OAc)₂2H₂O at 383 K for 2 h, yields dimethyltoluene-2,4-dicarbamate in 96% yield in 2 h, while Zn(OAc)₂2H₂O yields dimethyl-4,4-methylenediphenyldicarbamate in 98% yield at 453 K in 2 h.The structure of methyl 3-amino-4-methyl phenyl carbamate, which is one of the intermediates for the reaction of 2,4-toluene diamine with dimethyl carbonate into dimethyltoluene-2,4-dicarbamate, has been determined by measuring the NOE spectrum of ¹H NMR.     

Synthesis, Characterization, and Electrical Conductivity of Oligo[aromatic diimidoselenium(IV)]

Oligo[aromatic diimidoselenium] (PADIS) is prepared from the reaction of the disubstituted aromatic compounds, namely, 1,4-phenylenediamine, 4,4-thiodianiline, 1,1-biphenylene-4,4-diamine, and 2,2-dithiodianiline, with selenium dioxide in refluxing absolute ethanol. The four materials are investigated by elemental analysis, electronic spectra, Fourier Transform-infrared spectroscopy, and [¹H]NMR spectroscopy. The DC electrical conductivity variation with temperature in the range 300–500 K of the materials after annealing for 24 h at 100°C and after doping with 10% I₂ is determined for comparison.     

Preparation of poly(alkylvinylether)s for nonlinear optical applications

Summary 3,5-Dimethoxy-4-(2-vinyloxyethoxy)-4-nitrostilbene 2 and 3,5-dimethoxy-4-(2-vinyloxyethoxy)-2,4-dinitrostilbene 5 were prepared by the reactions of 2-iodoethyl vinyl ether with 3,5-dimethoxy-4-hydroxy-4-dinitrostilbene 1 and 3,5-dimethoxy-4-hydroxy-2,4-dinitrostilbene 4, respectively. Monomers 2 and 5 were polymerized with cationic initiators to obtain polymers with the NLO-phores 3,5-dimethoxy-4-oxy-4-nitrostilbene and 3,5-dimethoxy-4-oxy-2,4-nitrostilbene in the side chain. The resulting polymer 3 and 6 were soluble in DMSO and DMF. The inherent viscosities of polymers were in the range of 0.28–0.33 dL/g in DMSO. Polymers 3 and 6 showed good thermal stabilities in their TGA thermograms, and the T_g values from DSC thermograms were in the range of 81–87°C.