Catalytic cracking of isobutane over HZSM-5, FeHZSM-5 and CrHZSM-5 catalysts with different SiO<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> ratios

Several systems of HZSM-5, FeHZSM-5 and CrHZSM-5 zeolite catalysts with different ratios of SiO₂/Al₂O₃ (25,38,50,80, and 150) were prepared and they were characterized by means of X-ray diffraction (XRD), UV–Vis, NH₃-TPD and BET techniques. The results indicated that, compared with uncalcined HZSM-5 zeolites, the total acid amounts, acidic site density and acidic strength of HZSM-5, FeHZSM-5 and CrHZSM-5 zeolite catalysts obviously decreased, while those of weak acid amounts obviously enhanced with the decrease of SiO₂/Al₂O₃ molar ratio. When the ratio of SiO₂/Al₂O₃ is less than 50, the three systems of HZSM-5, FeHZSM-5 and CrHZSM-5 zeolite catalysts with same ratio of SiO₂/Al₂O₃ gave similar and high isobutane conversions. However, when the ratio of SiO₂/Al₂O₃ was equal to or greater than 80, these three systems of catalysts possessed different altering tendencies of isobutane conversions, thus their isobutene conversions were different. High yields of light olefins were obtained over the FeHZSM-5 and CrHZSM-5 zeolite catalysts with high ratio of SiO₂/Al₂O₃ (≥80). The ratio of SiO₂/Al₂O₃ has large effects on the surface area, and acidic characteristics of HZSM-5, FeHZSM-5 and CrHZSM-5 zeolites catalysts, and thus further affect their catalytic performances for isobutane cracking. That is the nature of SiO₂/Al₂O₃ ratio effect on the catalytic performances.     

Selective catalytic reduction of nitrogen monoxide with methane over impregnated In/HZSM-5 in the presence of excess oxygen

In/HZSM-5 catalyst prepared by the impregnation method was active for NO reduction with methane. Complete reduction of NO was obtained at 450°C over an In/HZSM-5 catalyst. The presence of oxygen in the feed greatly enhanced the NO reduction activity of In/HZSM-5. Co/HZSM-5 and Ga/HZSM-5 were less effective than In/HZSM-5. Cu/HZSM-5, In/Na-ZSM-5 and In₂O₃/Al₂O₃ were ineffective for NO reduction with CH₄. The NO reduction activity was proportional to the level of indium impregnated onto HZSM-5 but excess amounts of indium were detrimental to the catalytic activity. Phase analysis by XRD measurements demonstrated that there was a threshold value in the indium content, i.e., the maximum dispersion capacity of indium oxides. It is concluded that highly dispersed indium species are the active centers for the selective catalytic reduction of NO with CH₄.     

The Remarkable Effect of In2O3 on the Catalytic Activity of In/HZSM-5 for the Reduction of NO with CH4

In/HZSM-5/In₂O₃ catalyst that contained two different kinds of In induced by the impregnating and the physical mixing method respectively has shown remarkable activity for the CH₄-SCR of NO _x comparing with In/HZSM-5. The addition of In₂O₃ into In/HZSM-5 improved the NO conversion through enhancing the adsorption of NO _x over In/HZSM-5.     

Dual effects of supported W catalysts for dehydroaromatization of methane in the absence of oxygen

The screening of a series of W-based catalysts on different supports i.e. HZSM-5, Hβ, USY and Al₂O₃ for the dehydroaromatization of methane (DHAM) revealed that HZSM-5 emerged as the best support. Next, the performance of W/HZSM-5 and W-H₂SO₄/HZSM-5 catalysts for the DHAM reaction was compared to study the effect of acidic treatment in the impregnation method. The results showed that the optimum activity of W-H₂SO₄/HZSM-5 catalyst exceeded that of W/HZSM-5 catalyst. Finally, the influence of Si/Al ratio in the W-H₂SO₄/HZSM-5 catalyst was studied and the catalyst with Si/Al ratio = 30 was found to be the most promising for the DHAM reaction. The remarkable activity of the catalyst is attributed to the presence of dual effects: suitable content of octahedral polymeric and tetrahedral monomeric tungstate species accompanied by proper amount and strength of acid sites in the catalyst.     

Activity and stability of Cu/ZnO/Al2O3 catalyst promoted with B2O3 for methanol synthesis

The addition of B₂O₃ to a Cu/ZnO/Al₂O₃ catalyst increased the activity of the catalyst for methanol synthesis after an induction period during the reaction. The stability of the B₂O₃-containing Cu/ZnO/Al₂O₃ catalyst was greatly improved by the addition of a small amount of colloidal silica to the catalyst. This revised version was published online in July 2006 with corrections to the Cover Date.     

Performance of Ni catalyst supported on La-hexaaluminate in CO<Subscript>2</Subscript> reforming of CH<Subscript>4</Subscript>

CO₂ reforming of CH₄ was performed using Ni catalyst supported on La-hexaaluminate which has been an well-known material for high-temperature combustion. La-hexaaluminate was synthesized by sol-gel method at various conditions where different amount of Ni (5–20 wt%) was loaded. Ni/La-hexaaluminate experienced 72 h reaction and its catalytic activity was compared with that of Ni/Al₂O₃, Ni/La-hexaaluminate shows higher reforming activity and resistance to coke deposition compared to the Ni/Al₂O₃ model catalyst. Coke deposition increases proportionally to Ni content. Consequently, Ni(5)/La-hexaaluminate(700) is the most efficient catalyst among various Ni/La-hexaaluminate catalysts regarding the cost of Ni in Ni(X)/La-hexaaluminate catalysts. BET surface area, XRD, EA, TGA and TPO were performed for surface characterization. This work was presented at the 6 ^th Korea-China Workshop on Clean Energy Technology held at Busan, Korea, July 4–7, 2006.     

Characterization of Pd catalysts supported on USY zeolites with different SiO2/Al2O3 ratios for the hydrogenation of naphthalene in the presence of benzothiophene

A series of ultra-stable Y-type (USY) zeolites with different SiO₂/Al₂O₃ ratios in the range of 10–80 were used as supports for preparing Pd/USY at 2 wt% Pd loading. The FT-IR of hydroxyl groups of USY zeolites, the n-butylamine chemisorption and the temperature-programmed desorption were used in combination to characterize the zeolite acidity. TPR, H₂-TPD and chemisorption using H₂ were used to characterize the Pd reduction and dispersion. The hydrogenation of naphthalene was conducted at 200 °C in the presence of benzothiophene at different sulfur/metal ratios. The hydrogenation activity, selectivity, and the sulfur tolerance strongly depended on the SiO₂/Al₂O₃ ratio (thus the acidity) of the zeolites. The activity decreased with increasing SiO₂/Al₂O₃ in this range. The IR and n-butylamine TPD showed that both the amount and strength of Brönsted acidity decreased with the increase of the SiO₂/Al₂O₃ ratio. The good relationship between the acidity modification and catalytic performance suggests that the sulfur tolerance of Pd/USY zeolite might be due to the desired metal-support interaction, which resulted in larger amount of electron-deficient Pd. However, as shown in TGA and TPO-IR studies, the higher hydrogenation performance on more acidic zeolite also caused higher amount of carbonaceous species on the catalyst.     

Characterization of hydrodesulfurization catalyst prepared by impregnating cobalt nitrate solution onto the sulfided MoO3/Al2O3 catalyst

CoMo/Al₂O₃ catalysts were prepared by impregnating Cobalt nitrate solution into oxidic or sulfided Mo/Al₂O₃. The properties of CoMo/Al₂O₃ catalysts were characterized by XRD, TPS, oxygen chemisorption and ESR. Catalytic activity of CoMo/Al₂O₃ catalyst was evaluated by thiophene HDS as a probe reaction. When CoMo/Al₂O₃ catalyst was prepared by impregnating Cobalt nitrate solution into sulfided Mo/Al₂O₃, the interaction between Mo and alumina became weaker and the formation of synergic phase was facilitated. These structural changes may explain higher HDS activity of CoMo/Al₂O₃ catalyst prepared by impregnating Cobalt nitrate solution into sulfided Mo/Al₂O₃.     

Preparation and characterization of NiO/MgO/Al2O3 supported CoPcS catalyst and its application to mercaptan oxidation

MgO/Al₂O₃ and NiO/MgO/Al₂O₃ solid bases were prepared by mixing method. The samples were characterized by X-ray diffraction (XRD), CO₂ temperature-programmed desorption (CO₂-TPD) and surface area measurements. After supported sulfonated cobalt phthalocyanine (CoPcS) the catalytic performance of these catalysts was evaluated in the mercaptan oxidation reaction. The effect of Mg/Al mole ratios on activity, crystal structure, basicity and stability in air was discussed. And the mechanism of the effect of NiO was identified. Results show that the base amount of MgO/Al₂O₃ increases with increasing Mg/Al mole ratio and catalyst with high Mg/Al mole ratio has a higher initial activity. NiO/MgO/Al₂O₃–CoPcS shows a higher initial activity and a much longer lifetime than MgO/Al₂O₃–CoPcS. When nickel oxide is doped into the MgO/Al₂O₃ support more crystal defects are generated, which increases the amount and types of basic sites.     

The effect of sodium on the catalytic activity of ZnO–Al2O3/ZSM-5 and SnO–Al2O3/ZSM-5 for the transesterification of vegetable oil with methanol

In order to elucidate the effect of sodium on the activity of ZSM-5 supported metal oxides catalysts (ZnO–Al₂O₃/ZSM-5 and SnO–Al₂O₃/ZSM-5) for the transesterification of soybean oil with methanol, ZSM-5 supported metal oxides were prepared with and without sodium hydroxide by impregnation. The metal compositions of the ZSM-5 supported metal oxide catalysts and the metal concentrations dissolved from the catalysts to the methylester phase were measured by SEM-EDS and inductive coupled plasma spectroscopy, respectively. The catalytic activity of ZnO–Al₂O₃/ZSM-5 and SnO–Al₂O₃/ZSM-5 containing sodium did not originate from surface metal oxides sites, but from surface sodium sites or dissolved sodium leached from the catalyst surface.     

High Efficiency of Noble Metal and Metal Oxide Catalyst Systems for the Selective Reduction of NO with Propene in Lean Exhaust Gas

An investigation was conducted of noble metal and metal oxide catalysts deposited on Al₂O₃. The noble metals Pt, Pd, Rh the metal oxides CuO, SnO₂, CoO, Ag₂O, In₂O₃, catalysts were examined. Also investigated were noble metal Pt, Pd, Rh-doped In₂O₃/Al₂O₃ catalysts prepared by single sol–gel method. Both were studied for their capability to reduce NO by propene under lean conditions. In order to improve the catalytic activity and the temperature window, the intermediate addition propene between a Pt/Al₂O₃ oxidation and metal oxide combined catalyst system was also studied. Pt/Al₂O₃ and In₂O₃/Al₂O₃ combined catalyst showed high NO reduction activity in a wider temperature window, and more than 60% NO conversion was observed in the temperature range of 300–550 °C.     

Ru-Promoted CrO x /Al2O3 Catalyst for the Low-Temperature Oxidative Decomposition of Trichloroethylene in Air

A series of Ru-promoted CrO _x /Al₂O₃ as catalysts for the low-temperature oxidative decomposition of trichloroethylene (TCE) were characterized and evaluated in comparison with an unpromoted CrO _x /Al₂O₃ catalyst. Catalyst characterization was conducted by surface area measurement, X-ray diffraction and X-ray photoelectron spectroscopy. Catalyst performance in the TCE decomposition reaction was evaluated with respect to the initial catalytic activity, the rate of catalyst deactivation, and the product concentrations of CO and Cl₂ under dry or wet air conditions. The presence of a small amount of Ru, as much as 0.4 wt% in a CrO _x /Al₂O₃ catalyst, brought about several beneficial effects on the catalytic reaction performance. As compared with the unpromoted CrO _x /Al₂O₃, this Ru-promoted CrO _x /Al₂O₃ catalyst showed enhanced catalytic activity (249 versus 264 °C in terms of temperature at which 50% of TCE conversion occurred), a reduced concentration of CO (180 versus 325 ppm) in the product, and a decreased propensity to deactivation. Performance improvements of the Ru-promoted CrO _x /Al₂O₃ catalyst were thought to originate from its enhanced oxidation activity due to the coexisting highly-dispersed Ru oxides rendering less active Cr(III) to more active Cr(VI), and facilitating the process of supplying activated oxygen for the reaction system.     

A1PO4-Al2O3 catalysts with low alumina content. III. Surface basicity of catalysts obtained in aqueous ammonia

The amount of basic sites of A1PO₄-Al₂O₃ (APA1-A, 5–15 wt% Al₂O₃) catalysts at two basic strengths was measured by studying the liquid-phase adsorption of two acidic molecules (benzoic acid (BA, pK = 4.2) and phenol (PH, pKa = 9.9) from cyclohexane solutions, through the application of a spectrophotometric method. The data obtained follow the Langmuir adsorption isotherm and the monolayer coverage at equilibrium (at 298 K),X _m, is assumed as the amount of basic sites corresponding to the specific pK of the acid used as titrant. The amount of basic sites of any AlPO₄-Al₂O₃ catalyst is higher than that of AlPO₄, but lower than that of Al₂O₃. Besides, an increase in the Al₂O₃ content from 10 wt% gradually increases the basicity of the APA1-A catalyst. Moreover, calcination at increasing temperatures does not practically affect the surface basicity of APAl-A-5 and APAl-A-10 catalysts. However, for AlPO₄ content higher than 10 wt% we observe a decrease in surface basicity, this decrease depends on alumina content, i.e. it is higher as the amount of alumina increases. The basic sites of APAl-A systems catalyze the Knoevenagel condensation ofp-methoxybenzaldehyde and malononitrile at room temperature and in the absence of solvent.     

Methanol synthesis pathway over Cu/ZrO2 catalysts: a time‐resolved DRIFT 13C‐labelling experiment

X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) have been used to characterize a series of Cu/Ce/Al₂O₃ catalysts. Catalysts were prepared by incipient wetness impregnation using metal nitrate and alkoxide precursors. Catalyst loadings were held constant at 12 wt% CuO and 5.1 wt% CeO₂. Mixed oxide catalysts were prepared by impregnation of cerium first, followed by copper. The information obtained from surface and bulk characterization has been correlated with CO and CH₄ oxidation activity of the catalysts. Cu/Al₂O₃ catalysts prepared using Cu(II) nitrate (CuN) and Cu(II) ethoxide (CuA) precursors consist of a mixture of copper surface phase and crystalline CuO. The CuA catalyst shows higher dispersion, less crystalline CuO phase, and lower oxidation activity for CO and CH₄ than the CuN catalyst. For Cu/Ce/Al₂O₃ catalysts, Ce has little effect on the dispersion and crystallinity of the copper species. However, Cu impregnation decreases the Ce dispersion and increases the amount of crystalline CeO₂ present in the catalysts, particularly in Ce modified alumina prepared using cerium alkoxide precursor (CeA). Cerium addition dramatically increases the CO oxidation activity, however, it has little effect on CH₄ oxidation. This revised version was published online in July 2006 with corrections to the Cover Date.     

Preparation of MoO3/Al2O3 Catalysts with Sharp Eggshell Mo Distribution by Slurry Impregnation

MoO₃/Al₂O₃ catalysts with eggshell Mo concentration profiles were prepared by reaction of Al₂O₃ extrudates or balls with slurry of MoO₃ in water. The Mo concentration wave penetrating Al₂O₃ particles during this slurry impregnation was almost rectangular. Its height was close to the filled monolayer loading. The thickness of the shell was regulated either by impregnation time or by the MoO₃ amount in the slurry. The hydrodesulfurization activity of Mo species deposited by slurry impregnation was about the same or better (depending on the Al₂O₃ used) as in industrial MoO₃/Al₂O₃ catalyst.     

SSITKA studies of the catalytic flameless combustion of methane

This paper presents results which were obtained for the flameless combustion of methane over the Pd(PdO)/Al₂O₃ catalyst by using the steady state isotopic transient kinetic analysis method. During the reaction switches between ¹⁶O₂/Ar/CH₄/He and ¹⁸O₂/CH₄/He were carried out. The obtained results indicate the presence of large amounts of oxygen as well as of intermediates leading to the formation of carbon dioxide on the surface of the palladium catalyst. Additionally, information was obtained proving that the complete oxidation of methane over Pd/Al₂O₃ catalyst proceeds according to the Mars and van Krevelen redox mechanism. With the increase of the reaction temperature there is an increase in the number of active centres on the Pd(PdO)/Al₂O₃ catalyst surface—a larger amount of oxygen from the lattice of the catalyst is accessible for the reaction of methane oxidation.     

Production of hydrogen by steam reforming of bio-oil over Ni/Al2O3 catalysts: Effect of addition of promoter and preparation procedure

Catalytic steam reforming of bio-oil was investigated in a fixed bed tubular reactor for production of hydrogen. Two series of nickel/alumina (Ni/Al₂O₃) supported catalysts promoted with ruthenium (Ru) and magnesium (Mg) were prepared. Each catalyst of the first series (Ru–Ni/Al₂O₃) was prepared by co-impregnation of nickel and ruthenium on alumina. They were examined to investigate the effect of adding ruthenium on the performance of the catalysts for hydrogen production. The effect of the temperature, the most effective parameter in the steam reforming of bio-oil, on the activity of the catalysts was also investigated. Each catalyst of the second series (Ni–MgO/Al₂O₃) was prepared by consecutive impregnation using various preparation procedures. They were tested to determine the effect of adding magnesium as well as the effect of the preparation procedure on the outlet gas concentrations. It was shown that in both series, the catalysts were more efficient in hydrogen production as well as carbon conversion than Ni/Al₂O₃ catalysts. The highest hydrogen yield was 85% which was achieved over Ru–Ni/Al₂O₃ at 950 °C. It was also found that the effect of adding a small amount of ruthenium was superior to that of nickel on the yield of hydrogen when the nickel content was equal to or greater than 10.7%.     

Activity and characterization of Rh/Al2O3 and Rh-Na/Al2O3 catalysts for the SCR of NO with CO in the presence of SO2 and HCl

SO₂ and HCl are major pollutants emitted from waste incineration processes. Both pollutants are difficult to remove completely and can enter the catalytic reactor. In this work, the effects of SO₂ and HCl on the performance of Rh/Al₂O₃ and Rh-Na/Al₂O₃ catalysts for NO removal were investigated in simulated waste incineration conditions. The characterizations of the catalysts were analyzed by BET, SEM/EDS, XRD, and ESCA. Experimental results indicated the 1%Rh/Al₂O₃ catalyst was significantly deactivated for NO and CO conversions when SO₂ and HCl coexisted in the flue gas. The addition of between 2 and 10 wt.% Na promoted the activity of the 1%Rh/Al₂O₃ catalyst for NO removal, but decreased the CO oxidation and BET surface area. The catalytic activity for NO removal was inhibited by HCl as a result of the formation of RhCl₃. Adding Na to the Rh/Al₂O₃ catalyst decreased the inhibition of SO₂ because of the formation of Na₂SO₄, which was observed in the XRD and ESCA analyses. SEM mapping/EDS showed that more S was residual on the surface of the Rh-Na/Al₂O₃ catalyst than Cl.     

Improvement of coke resistance of Ni/Al2O3 catalyst in CH4/CO2 reforming by ZrO2 addition

This work investigates the improvement of Ni/Al₂O₃ catalyst stability by ZrO₂ addition for H₂ gas production from CH₄/CO₂ reforming reactions. The initial effect of Ni addition was followed by the effect of increasing operating temperature to 500–700 °C as well as the effect of ZrO₂ loading and the promoted catalyst preparation methods by using a feed gas mixture at a CH₄:CO₂ ratio of 1:1.25. The experimental results showed that a high reaction temperature of 700 °C was favored by an endothermic dry reforming reaction. In this reaction the deactivation of Ni/Al₂O₃ was mainly due to coke deposition. This deactivation was evidently inhibited by ZrO₂, as it enhances dissociation of CO₂ forming oxygen intermediates near the contact between ZrO₂ and nickel where the deposited coke is gasified afterwards. The texture of the catalyst or BET surface area was affected by the catalyst preparation method. The change of the catalyst texture resulted from the formation of ZrO₂–Al₂O₃ composite and the plugging of Al₂O₃ pore by ZrO₂. The 15% Ni/10% ZrO₂/Al₂O₃ co-impregnated catalyst showed a higher BET surface area and catalytic activity than the sequentially impregnated catalyst whereas coke inhibition capability of the promoted catalysts prepared by either method was comparable. Further study on long-term catalyst stability should be made.     

Direct syngas to DME as a clean fuel: The beneficial use of ultrasound for the preparation of CuO–ZnO–Al2O3/HZSM-5 nanocatalyst

A series of CuO–ZnO–Al₂O₃/HZSM-5 nanocatalysts prepared by impregnation, co-precipitation–physically mixing and combined co-precipitation–ultrasound methods and their catalytic activity investigated toward direct conversion of syngas to DME. BET, XRD, FESEM, TPR-H₂ and FTIR techniques were used to characterize nanocatalysts. XRD and FTIR results showed that structure of HZSM-5 is not damaged even after it is loaded with CuO–ZnO–Al₂O₃ nanoparticles. TPR-H₂ profiles indicated that reducibility of co-precipitation–ultrasound nanocatalyst is higher than other catalysts. It is found that employing ultrasound energy has great influence on the dispersion of nanocatalyst and its catalytic performance. Size distribution histogram of this nanocatalyst indicated that active phase particle size is between 25.7 and 125.4 nm and their average size is 47.86 nm. The physically mixing of CuO–ZnO–Al₂O₃ and HZSM-5 resulted in the low catalytic activity, indicating that the closest packing of both active sites for CO hydrogenation and methanol dehydration is necessary for direct synthesis of DME. The nanocatalyst loses negligible activity over the course of reaction due to coke formation on copper species.